The Effects of Different Processing Methods on the Morphology and Properties of PP/EPDM/Nano-CaCO3 Ternary Blend

The effects of different processing methods (direct extrusion, two-step extrusion or lateral injection extrusion) on the morphology of polypropylene (PP)/ethylene-propylene-diene terpolymer (EPDM)/calcium carbonate nanoparticles (nano-CaCO₃) ternary blend were investigated, including the morphology of the EPDM phase and the distribution of nano-CaCO₃ particles, by means of scanning electron microscopy (SEM). The results showed that the processing methods had a significant influence on the morphology of the EPDM phase and the distribution of nano-CaCO₃ particles. In the lateral injection extruded blends, it was amazingly observed that the EPDM particles encapsulated the PP phase tightly, and the dimension of EPDM particles was remarkably decreased. It was also found that the content of nano-CaCO₃ particles in the matrix of the lateral injection extruded blends was less than that of the two-step extruded blend, and that of the direct extruded blend was most. The properties of the ternary blend, including dynamic mechanical properties, rheological properties, and crystallization, were characterized in order to confirm the variety of morphologies caused by the different processing methods. The differences in the crystallization temperature, elastic modulus, and glass transition temperature of the blends prepared by different methods well agreed with the variation of their morphology.     

Mechanical Properties and Crystallization Behavior of Polycarbonate/Polypropylene Blends

The mechanical properties, morphology, and crystallization behavior of polycarbonate (PC)/polypropylene (PP) blends, with and without compatibilizer, were studied by tensile and impact tests, scanning electron microscopy (SEM), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The tensile and impact strengths of PC/PP blends decreased with increasing the PP content due to poor compatibility between the two phases. But the addition of compatibilizer improved the mechanical properties of the PC/PP blends, and the maximum value of the mechanical properties, such as tensile and impact strengths of PC/PP (80/20 wt%) blends, were obtained when the compatibilizer was used at the amount of 4 phr. The SEM indicated that the compatibility and interfacial adhesion between PC and PP phases were enhanced. DSC results that showed the crystallization and melting peak temperatures of PP increased with the increase of the PP content, which indicated that the amorphous PC affected the crystallization behavior. However, both the PC and compatibilizer had little effect on the crystallinity of PP in PC/PP blends based on both the DSC and XRD patterns.     

Relationship between Microstructure and Mechanical Properties of Ethylene-Octene Copolymer Reinforced and Toughened PP

Polypropylene (PP)/ethylene-octene copolymer (POE) blends with 10–50wt% POE composition were prepared using a twin-screw extruder in the melt state. Mechanical properties of PP and PP/POE blends were tested and the effect of POE content on the crystalline morphology and structure, melting and crystallization behavior, compatiblilty, phase morphology, and the interface cohesiveness of the blends were investigated by polarizing optical microscope (POM), wide-angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and scanning electron microscopy (SEM). The relationship between mechanical properties and microstructure of the PP/POE blends is discussed. The results showed that POE had a dual function of both reinforcing and toughening PP in the range from 10–40wt%, which was attributed to the integrated functions of the degree of crystallinity of the PP phase, phase morphology, and interface cohesiveness of the blend.     

BLENDS OF THERMOTROPIC LIQUID CRYSTALLINE POLYESTER AND POLY(ETHYLENE TEREPHTHALATE)

Two kinds of blends of thermotropic liquid crystalline polymers (LCPs) and poly(ethylene terephthalate) (PET) were prepared by solution and melt blending, respectively. Crystallization behavior of the blends was observed by differential scanning calorimetry (DSC). The LCP in both blends considerably decreased the cold crystallization temperature of PET and increased the crystallization rate in the low-temperature region, but did not show any significant effect on crystallization in the high-temperature region. Phase behavior of samples prepared by melt blending was investigated with the scanning electronic microscope (SEM). It was found that LCP/PET blends display a biphasic structure with an aromatic unit-rich phase as a dispersed domain, and a highly oriented fibrous structure was formed on the fracture surface of the blends. During the melt blending process, PET reacted with LCP through transesterification, as indicated by both DSC and SEM measurements.     

Effects of Montmorillonite on the Nonisothermal Crystallization Behavior of the Poly(trimethylene terephthalate)/Polypropylene/Montmorillonite Nanocomposites

Organic montmorillonite (MMT) reinforced poly(trimethylene terephthalate) (PTT)/ polypropylene (PP) nanocomposites were prepared by melt blending. The effects of MMT on the nonisothermal crystallization of the matrix polymers were investigated using differential scanning colorimetry (DSC) and analyzed by the Avrami equation. The DSC results indicated that the effects of MMT on the crystallization processes of the two polymers exhibited great disparity. The PTT's crystallization was accelerated significantly by MMT no matter whether PTT was the continuous phase or not, but the thermal nucleation mode and three-dimensional growth mechanism remained unchanged. However, in the presence of MMT, the PP's crystallization was slightly retarded with PP as the dispersed phase, and was influenced little with PTT as the dispersed phase. When the MMT content was increased from 2_wt% to 7_wt%, the crystallization of the PTT phase was slightly accelerated, whereas the crystallization of the PP phase was severely retarded, especially at lower temperatures. Moreover, the nucleation mechanism for the PP's crystallization changed from a thermal mode to an athermal one. In the polypropylene-graft-maleic anhydride (PP-g-MAH) compatibilized PTT/PP blends, with the addition of 2_wt% MMT during melt blending, the T _c (PTT) shifted 7.8°C to lower temperature and had a broadened exotherm, whereas the T _c (PP) shifted 17.1°C to higher temperature, with a narrowed exotherm. TEM analysis confirmed that part of the PP-g-MAH was combined with MMT during blending.     

Effect of Maleated Styrene/Ethylene-co-Butylene/Styrene on the Dispersed Particles Size and Mechanical Properties of Polyamide 6/Poly(styrene-co-acrylonitrile)/Poly(styrene-b-(ethylene-co-butylene)-b-styrene) Ternary Blends

In this study, the effect of several parameters, including composition, order of mixing, viscosity, and interfacial tension, on the phase structure and size of dispersed particles of polyamide 6 (PA6)/poly(styrene-co-acrylonitrile) SAN/poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) ternary blends was investigated. Moreover, the effect of addition of different ratios of reactive SEBS (maleic anhydride grafted-SEBS) and non-reactive SEBS at a fixed order of mixing and composition of 70/15/15 (PA6/SAN/SEBS + SEBS-g-MAH) on the mechanical properties of ternary blends was examined. Scanning electron microscopy (SEM) micrographs showed that among the studied parameters, interfacial tension and viscosity of dispersed phases were the leading factors in the formation of morphology and size of dispersed droplets. Mechanical results revealed that in contrast to the expectation, formation of core/shell structure of PA6/SAN/SEBS ternary blends did not result in a significant increasing of impact strength. The highest impact strength was achieved when a 50/50 weight ratio of SEBS/SEBS-g-MAH was used.     

Miscibility and Isothermal Crystallization Behavior of Poly (Butylene Succinate-co-Adipate) (PBSA)/Poly (Trimethylene Carbonate) (PTMC) Blends

Poly(butylene succinate-co-adipate) (PBSA)/poly (trimethylene carbonate) (PTMC) blend samples with different weight ratios were prepared by solution blending. The morphologies after isothermal crystallization and in the melt were observed by optical microscopy (OM). Differential scanning calorimetry (DSC) was used to characterize the isothermal crystallization kinetics and melting behaviors. According to the OM image before and after melting, it was found that the blends formed heterogenous morphologies. When the PTMC content was low (20%), PBSA formed the continuous phase, while when the PTMC contents was high (40%), PBSA formed the dispersed phase. The glass transition temperatures (T_g) of the blends were determined by DSC and the differences of the T_g values were smaller than the difference between those of pure PBSA and PTMC. In addition, the equilibrium melting points were depressed in the blends. According to these results, the PBSA/PTMC blends were determined as being partially miscible blends. The crystallization kinetics was investigated according to the Avrami equation. It was found that the incorporation of PTMC did not change the crystallization mechanism of PBSA. However, the crystallization rate decreased with the increase of PTMC contents. The change of crystallization kinetics is related with the existences of amorphous PTMC, the partial miscibility between PLLA and PTMC, and the changes of phase structures.     

Preparation,Morphology and Properties of Poly(Trimethylene Terephthalate)/Thermoplastic Polyester Elastomer Blends

Poly(trimethylene terephthalate)(PTT)/thermoplastic polyester elastomer (TPEE) blends were prepared and their miscibility, crystallization and melting behaviors, phase morphology, dynamic mechanical behavior, rheology behavior, spherulites morphology, and mechanical properties were investigated by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), parallel-plate rotational rheometry, polarized optical microscopy (POM), wide angle X-ray diffraction (WAXD), universal tensile tester and impact tester, respectively. The results suggested that PTT and TPEE were partially miscible in the amorphous state, the TPEE rich phase was dispersed uniformly in the solid matrix with a size smaller than 2 μm, and the glass transition temperatures of the blends decreased with increasing TPEE content. The TPEE component had a good effect on toughening the PTT without depressing the tensile strength. The blends had improved melt viscosities for processing. When the blends crystallized from the melt state, the onset crystallization temperature decreased, but they had a faster crystallization rate at low temperatures. All the blends’ melts exhibited a predominantly viscous behavior rather than an elastic behavior, but the melt elasticity increased with increasing TPEE content. When the blends crystallized from the melt, the PTT component could form spherulites but their morphology was imperfect with a small size. The blends had larger storage moduli at low temperatures than that of pure PTT.     

Influence of halloysite nanotubes (HNTs) on morphology,crystallization, mechanical and thermal behaviour of PP/ABS blends and its composites in presence and absence of dual compatibilizer

Halloysite nanotubes (HNTs) filled 80/20 (wt/wt) polypropylene (PP)/acrylonitrile butadiene styrene (ABS) blends and its composites in presence and absence of dual compatibilizer (polypropylene grafted maleic anhydride (PP-g-MA), and styrene-ethylene, butylene-styrene triblock copolymer grafted with maleic anhydrite (SEBS-g-MA)) have been prepared using twin screw extruder followed by injection moulding. Significant refinements in dispersed ABS droplets diameter and interparticle distance between dispersed ABS droplets were observed in case of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. This has resulted in significant enhancement in tensile and impact properties of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. Refinement in morphology of dispersed ABS phase results in decrease in crystallinity of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. In addition, HNTs act as heterogeneous nucleating agent for the growth of PP crystals, and hence crystallization rate of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence and absence of PP-g-MA and SEBS-g-MA increases. Thermal stability also increases in case of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence and absence of PP-g-MA and SEBS-g-MA.     

Fracture Micromechanisms of Polypropylene/Polycarbonate/Poly(styrene-b-(ethylene-co-butylene)-b-styrene) (PP/ PC/SEBS) Ternary Blends: The Effects of SEBS Content

Ternary blends of polypropylene/polycarbonate/poly(styrene-b-(ethylene-co-butylene)-b-styrene) (PP/PC/SEBS) with varying SEBS contents were produced via melt blending in a co-rotating twin-screw extruder. The phase morphology of the resulting ternary blends and its relationship with bending and impact behaviors were studied. Transmission optical microscopy (TOM) of the crack tip damage zone and scanning electron microscopy (SEM) of impact fractured surfaces were performed to characterize the fracture mechanism. With increasing SEBS content in the PP/PC/SEBS ternary blends, the number of PC/SEBS core-shell particles increased and the size of the core-shell particles enlarged. It was shown that with an SEBS content of 5%, the crack initiation resistance decreased and then was almost unchanged with further increase of SEBS content, while resistance to crack growth increased continuously with increasing of SEBS content. Preliminary analysis of the micromechanical deformation suggested that the high impact toughness observed for samples containing 20 and 30 wt% of SEBS could be attributed to cavitation of the rubbery shell and, consequently, shear yielding of the matrix. This plastic deformation absorbed a tremendous amount of energy. Due to low interfacial adhesion between PC particles and PP matrix in samples containing 5 and 10 wt% of SEBS, debonding occurred too early, so the occurrence of matrix shear yielding was delayed and resulted in premature interfacial failure and, hence, rapid crack propagation.     

Microstructures and Mechanical Properties of Poly(Trimethylene Terephthalate)/Maleic Anhydride Grafted Poly(Ethylene-octene)/Polypropylene Blends

A range of blends based on 70 wt% of poly(trimethylene terephthalate) PTT with 30 wt% dispersed phase were produced via melt blending. The dispersed phase composition was varied from pure maleic anhydride grafted poly(ethylene-octene) (POE-g-MA) over a range of POE-g-MA:polypropylene (PP) ratios. The micromorphology and mechanical properties of the ternary blends were investigated. The results indicated that the domains of the POE-g-MA are dispersed in the PTT matrix, and at the same time the POE-g-MA encapsulate the PP domains. The interfacial reaction between the hydroxyl-end group of PTT and maleic anhydride (MA) during melt blending changes the formation from “isolated formation” to “capsule formation,” where the PP domains are encapsulated by POE-g-MA. Compared to the PTT/POE-g-MA blends, mechanical properties of ternary blends, such as tensile strength and Young's modulus, were improved significantly.     

Shape Memory Properties of Melt-Blended Olefin Block Copolymer (OBC)/Ethylene-Vinyl Acetate Blends

The completely crosslinked shape memory polymer blends (SMPs) traditionally suffer from recycling problems due to their network structure. In this paper we describe the thermal, mechanical, and shape memory behavior of physical blends of OBC (Olefin block copolymer) and EVA (Ethylene-vinyl acetate copolymer), with and without modification of one or both of the components, prepared using a melt-blending method. These behaviors of the modified blends, based on maleated OBC (OBC-g-MA) and/or vinyltriethoxysilane (VTEOS) modified EVA, included OBC/EVA-g-VTEOS, OBC-g-MA/EVA, and OBC-g-MA/EVA-g-VTEOS blends; they were investigated to compare with the OBC/EVA blend. The SEM (scanning electron microscopy) observations showed that the compatibility of the silane and maleic anhydride modified OBC/EVA blends were better than that of the unmodified OBC/EVA blend. The crystallization temperatures of OBC and EVA in the modified blends were higher than those in the neat blend. The OBC-g-MA/EVA-g-VTEOS blend had the highest modulus and thermal stability of all investigated blend systems due to the numerous interactions between maleic anhydride and silane. The shape memory performance, as defined by the shape fixity ratio (R_f) and shape recovery ratio (R_r), was higher for the modified blends of one or both of the modified components than that for the OBC/EVA blend. These modified blends were readily reprocessible, like thermoplastic vulcanizates, and still retained shape memory behavior, in contrast with the fully crosslinked shape memory polymer blends; thus they were also improved in terms of the environmental aspects of processing.     

Compositional Dependence of Static Shear Viscosity of Immiscible PP/PS Blends

Phase structures of immiscible polypropylene (PP)/polystyrene (PS) blends with different volume proportions, PP90/PS10, PP80/PS20, PP70/PS30, PP60/PS40, PP50/PS50, PP40/PS60, PP30/PS70, PP20/PS80, PP10/PS90, were observed by means of scanning electronic microscopy (SEM). The zero shear viscosities of the blends were determined according to a modified Carreau model by fitting the curves of static shear rate sweeps of blends tested at 190°C in a Stress Tech Fluids Rheometer. The results showed that the compositional dependence of zero shear viscosity of PP/PS deviated greatly from linear or log‐linear additivity. When PS was dispersed in a PP continuous phase, the blends showed negative deviation, while for blends with PP dispersed in a PS matrix, positive deviation was generated. When different theoretical equations of Nielsen, Utracki, Taylor, Frankel‐Acrivos (FA), Choi‐Schowalter (CS), and Han‐King (HK) were used to fit the experimental data of zero shear viscosities of blends, none of them was suitable for PP/PS blends. These experimental phenomena may result from the complex phase structures of the blends and their response to shear conditions, which are discussed in detail and compared with the experimental analysis.     

Studies on the Nonisothermal Crystallization Behavior of Polypropylene/Multiwalled Carbon Nanotubes Nanocomposites

Polypropylene/multiwalled carbon nanotubes (PP/MWNTs) nanocomposites were prepared by a melt compounding process. The morphology and nonisothermal crystallization of these nanocomposites were investigated by means of optical microscopy, scanning electron microscopy, and differential scanning calorimetry. Scanning electron microscope micrographs of PP/MWNTs composite showed that the MWNTs were well dispersed in the PP matrix and displayed a clear nucleating effect on PP crystallization. Avrami theory, modified by Jeziorny and Mo's method, was used to analyze the kinetics of the nonisothermal crystallization process. It was found that the addition of MWNTs improved the crystallization rate and increased the peak crystallization temperature of the PP/MWNTs nanocomposites as compared with PP. The results show that the Jeziorny theory and Mo's method successfully describe the nonisothermal crystallization process of PP and PP/MWNTs nanocomposites.     

The Effect of Microwave Irradiation on the Crystallization Behavior of PET/PEN Blends

The crystallization behavior of poly(ethylene terephthalate) (PET)/poly(ethylene‐ 2,6‐naphthalate) (PEN) blends before and after microwave irradiation for different time intervals has been investigated by means of wide angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC) techniques. It was found that microwave irradiation could greatly affect the crystallization behavior of PET/PEN blends and significantly enhance their degree of crystallinity. For the PET/PEN (90/10) blends, the degree of crystallinity increased from 15 to 45%; for the PET/PEN (60/40) blends, the degree of crystallinity significantly increased, from 1 to 36%. However, with increasing irradiation time, the degree of crystallinity didn't continually increase. It reached a maximum at certain time point. The cold crystallization enthalpy △Hcc gradually decreased as microwave irradiation time increased and the melting enthalpy △Hm vis‐à‐vis the long time interval of such irradiation was decreased. In addition, the mechanism for microwave irradiation affecting the crystallization behavior of polymers is discussed.     

The Construction of Sandbag Microstructure in Polyamide 6/Ethylene-Propylene-Diene Terpolymer/Nanometer Calcium Carbonate Ternary Composite

A sandbag microstructure was constructed in Polyamide 6(PA6)/ethylene-propylene-diene terpolymer (EPDM)/nanometer calcium carbonate (nano-CaCO₃) ternary composites by the addition of maleinated EPDM (EPDM-g-MA) to reduce the interfacial tension between EPDM and PA6 and EPDM and nano-CaCO₃. Scanning electron microscopy (SEM) observation and differential scanning calorimetry (DSC) analysis revealed that the microstructure of the ternary composites evolved from the initial separated EPDM and nano-CaCO₃ dispersion structure to the sandbag structure and finally to the separated dispersion structure again with the increase of EPDM-g-MA content in the elastomer phase. The mechanical results showed the composites with the sandbag microstructure exhibited excellent toughness and stiffness.     

Synthesis of Polypropylene/Attapulgite Nanocomposites and Their Crystallization Behavior Studied by Step-Scan DSC

Attapulgite (AT) was modified by grafting with butyl acrylate (BA) via polymerizations initiated by Gamma radiation. Polypropylene (PP)/AT nanocomposites were synthesized via melt extrusion in a twin-screw extruder. Fourier transform infrared (FTIR) spectroscopy and thermogravimetry (TG) were used to assess the structure of the hybrid materials and the dispersion of AT was verified by transmission electron microscopy (TEM). The crystallization kinetics of PP/AT nanocomposites were investigated by differential scanning calorimetry (DSC) and analyzed by using the Avrami method. The isothermal crystallization kinetics showed that the addition of AT increased both the crystallization rate and the isothermal Avrami exponent of PP. Step-scan differential scanning calorimetry (SDSC) was used to study the influence of AT on the crystallization and subsequent melting behavior. The results revealed that PP and PP/AT nanocomposites experienced multiple melting and secondary crystallization processes during heating. The melting behaviors of PP and PP/AT nanocomposites varied with the variation of crystallization temperature and AT content.     

Effect of Interfacial Structure on Crystallization Behavior of Polypropylene/Polyolefin Elastomer/Barium Sulfate Ternary Composites

In this paper, interfacial structure induced development of crystallization behavior of polypropylene (PP)/polyolefin elastomer (POE)/barium sulfate (BaSO₄) ternary composites was studied by DSC. Two kinds of PP (copolymer and homopolymer) were used. The compatibility between PP and POE had a distinct influence on nucleation and crystal growth of PP in PP/POE binary composites. The crystallization rate of PP homopolymer increased because of the heterogeneous nucleation by POE, while the crystallinity of PP homopolymer decreased because of an inhibition effect of the hexane side chains in POE. BaSO₄ particles acted as heterogeneous nucleating agents of PP in ternary composites. The dispersion of BaSO₄, controlled by interfacial design, had a distinct influence on the nucleation activity of BaSO₄ in ternary composites. Interfacial structure had the same effect on nucleation activity of BaSO₄ particles and crystallization rate of PP matrix in PP copolymer ternary composites as those in PP homopolymer ternary composites.     

Crystallization Behavior of Poly(Lactic Acid) Filled with Modified Carbon Black

A novel method was employed to modify the surface of carbon black (CB) by an organic small molecule in a Haake Rheomix mixer. The modified carbon black (MCB) was dispersed uniformly in poly(lactic acid; PLA). The crystallization behaviors of PLA, PLA/CB and PLA/MCB composites were investigated by differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS) and polarizing optical microscopy. It is found that the addition of CB or MCB can influence the crystallization behavior of PLA. PLA/MCB has a faster crystallization rate and higher crystallization peak temperature than PLA/CB. For non-isothermal studies, Jeziorny and Mo equations were employed. The Mo equation can well describe the non-isothermal crystallization of the three samples. For PLA/CB and PLA/MCB composites containing 3wt% fillers, the nucleating activity for CB is about 0.32, and about 0.16 for MCB. All these results show that MCB is an effective nucleating agent. PLA/MCB has a higher nucleation rate than PLA/CB because of the finer dispersed particles size and improved interaction between MCB and PLA.     

Reactive Compatibilization of Poly(trimethylene terephthalate)/Polypropylene Blends by Polypropylene‐graft‐Maleic Anhydride. Part 1. Rheology,Morphology, Melting,and Mechanical Properties

Poly(trimethylene terephthalate)/polypropylene (PTT/PP) blends were prepared by melt blending. The rheology, morphology, melting, and mechanical properties of PTT/PP blends were investigated with and without the addition of polypropylene‐graft‐maleic anhydride (PP‐g‐MAH). The melt viscosity results showed that the fluid behavior of PTT/PP blends exhibited great disparity to that of PTT but similar to that of PP; the dispersed flexible PP phase in the blends served as a “ball bearing effect” under shear stress, which made the fluid resistance markedly reduced; by contrast, the relatively rigid PTT dispersed phase made only a small contribution to the viscosity. With 5 wt.% PP‐g‐MAH addition during melt processing, both the shear viscosity and the non‐Newtonian index of 70/30 PTT/PP blend were increased over that of the corresponding uncompatibilized one, whereas the shear viscosity of the 30/70 PTT/PP melt decreased slightly indicating that a considerable amount of PP‐g‐MAH did not act as compatibilizer but probably served as plasticizer.

With the increasing of the other component, the melting temperature of the PTT phase showed a slight decrease while the melting temperature of the PP phase showed a slight increase. 5 wt.% PP‐g‐MAH addition had little influence on the melting temperatures of the two components. When PP≤20 wt.%, the cold crystallization temperature of the PTT phase (T_cc (PTT‐phase)) showed little change with the composition; however, it shifted to higher temperature when PP≥30 wt.%. The variations of the T_cc (PTT‐phase), with and without PP‐g‐MAH, suggested that, when PTT was a minor component, the excess PP‐g‐MAH which did not act as compatibilizer might serve as a plasticizer that made the PTT's cold crystallization process to be easier. The SEM results indicated that, for the uncompatibilized blends, the interfaces from particles pulling‐out are clear and smooth, while, for compatibilized blends, the reactive products are at the interfaces. The mechanical properties suggested that PP‐g‐MAH did not result in significant improvement of the toughness of the blend, but the tensile strength increased markedly.