Designing and Characterization of Biodegradable Multiblock Poly(L-Lactic Acid)/Polybutadiene Elastomers

A series of poly(L-lactic acid)/polybutadiene (PLA/PB) biodegradable multiblock elastomers was synthesized and characterized. A two-step process to prepare PLA/PB multiblock elastomers was applied. Melt polymerization was used to prepare poly(L-lactic acid) (PLA) terminated with hydroxyl groups and, at the same time, hydroxyl-terminated polybutadiene (HTPB) and 1,6-hexamethylene diisocyanate (HDI) were employed to synthesize diisocyanate-terminated polybutadiene (ITPB). Then, PLA and ITPB were reacted with different PLA/PB weight ratios. Consequently, a series of PLA/PB biodegradable poly(ester-urethane)s with crosslinked chains was obtained. Swelling characteristics and crosslink density of the crosslinked elastomer were investigated. DMA was applied to characterize its thermal properties. The measurement of mechanical properties showed that a PLA/PB elastomer with adjustable mechanical properties was synthesized. Micromorphology, hydrophobicity, and degradability of the material were also characterized.     

Fabrication and Physical Characterization of Biodegradable Poly(butylene succinate)/Carbon Nanofiber Nanocomposite Foams

Nanocomposites of biodegradable poly(butylene succinate) (PBS) and carbon nanofibers (CNFs) were prepared by three different methods, that is, solution blending, melt compounding, and solution and subsequent melt blending (SOAM) method, among which the SOAM method, where nano-scale fillers and polymer matrix are solution-blended and subsequently melt-mixed in a torque rheometer, is a two-step process for obtaining polymer nanocomposite. Dispersion of CNFs in the PBS matrix was characterized by FE-SEM, while thermal and mechanical properties were analyzed by thermogravimetric ananlysis (TGA) and universal test machine (UTM), respectively. The PBS/CNF nanocomposites were then converted to foams by employing a chemical blowing agent (CBA) in the melt. The presence of CNFs increased the melt viscosity of PBS so that the PBS/CNF nanocomposite foams were produced without modifying the chemical structure of the PBS. Nanocomposite foams prepared by the SOAM method showed higher physical properties compared with those prepared by the solution blending and the melt mixing. Cell size and blowing ratio increased with the increase in the CBA content, blowing temperature and time. Cell morphology of the nanocomposite foams was examined by optical microscopy, and the cell size distribution was also investigated.     

Preparation and Properties of Novel Maleated Poly (D,L-lactide-co-glycolide) Porous Scaffolds for Tissue Engineering

Three-dimensional biodegradable porous scaffolds play an important role in tissue engineering. A new polymer based on maleated poly(lactic-co-glycolic acid) (MPLGA) was synthesized using direct melt copolymerization from maleic anhydride (MAH), D, L-lactide, and glycolide monomers. MPLGA porous biodegradable scaffolds were prepared by a solution-casting/salt-leaching method. The effects of content and size of the NaHCO₃ porogen on the compressive strength of the MPLGA scaffolds were investigated, and the effect of content of the porogen on the porosity of the MPLGA scaffolds was also studied. The results indicated that MAH was grafted onto PLGA successfully and MPLGA scaffolds with interconnective and open pore structure were obtained. Increasing content of NaHCO₃ porogen resulted in an increase of porosity and decrease of the compressive strength of the MPLGA scaffolds with the compressive strength of the scaffolds also decreasing with increasing porogen size.     

Synthesis,Characterization and Thermal Properties of Bio-Based Poly(Ethylene 2,5-Furan Dicarboxylate)

Poly(ethylene 2,5-furan dicarboxylate) (PEF), based on renewable resources, was synthesized using several different polycondensation methods and then characterized. In this study the properties of polycondensed PEF were compared using five types of catalysts and two types of monomers. For the optimal catalyst, the influence of the amount of catalyst, polycondensation temperature and polycondensation time were investigated and, thereafter, direct and indirect polycondensations were compared at the optimum conditions. Various properties of PEF were characterized by Fourier transform infrared spectroscopy, intrinsic viscosity, gel permeation chromatography, ¹H NMR, differential scanning calorimetry, dynamic mechanical thermal analysis, thermogravimetric analysis, and X-ray diffraction for comparison with the properties of polyethylene terephthalate PET. In addition, the rheological behaviour and mechanical properties of the PEFs were tested. The results confirmed that the obtained properties of PEF were similar to the corresponding properties of PET.     

Synthesis and Kinetic Study of Thermal Cycloimidization of Novel Poly(Amide Amic Acid) to Poly(Amide Imide) by Thermogravimetric Analysis

A new series of fluorinated poly(amide imide)s (PAIs) were prepared by polycondensation of diamine amic acid (DAA) with isophthaloyl, terephthaloyl, or trimellitic anhydride chloride in dimethylformamide, and their subsequent thermal cycloimidization. DAAs were obtained by reacting 4, 4′ (hexafluoroisopropylidene) diphthalic anhydride (6FDA) with diamines in dimethylformamide at 0–5°C. The kinetics of thermal cycloimidization of poly(amide amic acid) (PAA) to PAIs was investigated by thermogravimetric analysis under isothermal conditions at four different temperatures, i.e. 175, 200, 225, and 260°C, for 75 min. A generalized equation to calculate the theoretical amount of weight loss upon complete imidization, i.e. T_w % = 18Nw/R _Mw, was developed. In the above equation numeral 18 corresponds to the molecular weight of water, N is the number of water molecules, which are eliminated per repeat unit of PAA upon cycloimidization, w is the weight of PAA taken for TGA, and R _Mw is the molecular weight of the repeat unit of PAA. The polymers were characterized by FT-IR spectra. Complete cycloimidization process is discussed in terms of monomer structure (diamines and acid chlorides), effect of imidization temperature and time, types of linkages (meta or para) present, and influence of electron withdrawing groups, such as sulfone, in the monomer structure. It was observed that cycloimidization occurred at a faster rate at the beginning, up to about 30 min, and then proceeded at a slower rate till the end of curing. The thermal and thermooxidative stabilities of PAIs were also investigated in nitrogen and oxygen atmosphere.     

Nonisothermal Crystallization Kinetics of Poly(lactic acid) Nucleated with a Multiamide Nucleating Agent

Addition of a commercial available multiamide compound (N,N′,N′′-tricyclohexyl-1,3,5- benzenetricarboxylamide, defined here as TMC) into ecofriendly poly(lactic acid) (PLA) can accelerate the crystallization rate of the material remarkably and broaden its applications. In this paper, the nonisothermal crystallization behavior of biodegradable PLA nucleated by 0.3 wt.% of TMC was investigated by differential scanning calorimetry (DSC). The modified Avrami, Tobin, Ozawa, and Mo models were applied to describe the kinetics of the crystallization process. Various parameters of nonisothermal crystallization, such as the crystallization half-time and crystallization rate constant, reflected that TMC significantly accelerated the crystallization process. The activation energy values of the neat PLA and PLA/TMC blend, determined by the Kissinger method, increased with the addition of TMC. The study should be helpful for understanding the relationship between processing and properties of this material.     

Evaluation of the Complexation Process Between Poly(Aspartic Acid) and Poly(Ethylene Glycol) Through Dynamic Rheology and Electrokinetic Potential

Investigations concerning the interactions between the polymeric pair constituted of poly(aspartic acid) (PAS) as a proton-donating polycarboxilic acid and poly(ethylene glycol) (PEG) as a proton-accepting compound are continued from previous studies. The complexation between PAS and PEG has potential use as a matrix for encapsulation of bioactive substances with potential biomedical applications. The interactions that occurred were monitored in dilute solutions by determining the particle size distribution and the zeta potential (ZP) through laser light scattering method; data associated with oscillatory rheology was used as a complementary analysis. The influence of the ratio between the components and the temperature conditions during the complexation process brought additional data concerning the intermolecular links formed through hydrogen bonds.     

各种烷氧基取代聚对苯乙炔的合成和发光性能研究

利用脱氯缩合聚合法合成了聚（2－甲氧基－5－丁氧基）对苯乙炔（PMOBOPV），聚（2－甲氧基－5－辛氧基）对苯乙炔（PMOCOPV）和聚（2－丁氧基－5－丁氧基）对苯乙炔（PDBOPV），聚（2－辛氧基－5－辛氧基）对苯乙炔（PD－COPV）4种发光材料。对反应体系的浓度，酸碱度，反应温度及时间等工艺条件和路线进行了细致的研究。结果表明：反应物的纯度，含量对合成产物的产率和性能有较大的影响；碱性是影响脱氯缩合反应的关键因素，而反应温度和时间对缩合反应影响则相对较小，在一定温度下当反应时间达到一定阶段后其转化率基本不变，对合成材料的化学结构，物理性能和发光特性进行了表征和检测。结果显示：非对称烷氧基取代PPV具有良好的溶解性，成膜性和稳定性；而对称性烷氧基取代PPV的溶解性和成膜性相对较差。以PMOBOPV为发光材料，采用旋涂工艺制作出单层和双层发光器件，并对器件的电致和光致发光性能进行了研究。     

Improving the Barrier Properties of Poly(Lactic Acid) by Blending with Poly(Ethylene-Co-Vinyl Alcohol)

Poly(lactic acid) (PLA)/poly(ethylene-co-vinyl alcohol) (EVOH) blends were prepared via melt blending to improve the barrier properties of PLA. The phase morphologies and final properties (rheological behavior, thermal and dynamical-mechanical features, barrier properties, and mechanical behaviors) of the blends were investigated as a function of the EVOH content. The results indicated that hydroxyl groups of EVOH promoted the degradation of PLA, and thus affected the viscosities and morphologies of the resulting blends. The intrinsic viscosities of PLA in the blends decreased with the content of EVOH. The PLA and EVOH presented typical phase-separated morphologies, with a relatively small domain size of the EVOH phase. The EVOH enhanced the cold-crystallization behavior of PLA. The barrier properties to water vapor and oxygen increased linearly with increasing EVOH content.     

Optimization of Preparation Techniques for Poly(Lactic Acid-Co-Glycolic Acid) Nanoparticles

Microparticles and nanoparticles of poly(lactic acid-co-glycolic acid) (PLAGA) are excellent candidates for the controlled release of many pharmaceutical compounds because of their biodegradable nature. The preparation of submicron PLAGA particles poses serious challenges that are not necessarily present when preparing microparticles. We have evaluated several combinations of organic solvents and surfactants used in the formulation of PLAGA nanoparticles. Critical factors such as the ability to separate the nanoparticles from the surfactant, the ability to re-suspend the nanoparticles after freeze-drying, formulation yield and nanoparticle size were studied. The smallest particles were obtained using the surfactant/solvent combination of sodium dodecyl sulfate and ethyl acetate (65 nm) and the largest particles were obtained using poly(vinyl alcohol) and dichloromethane (466 nm). However, the optimal nanoparticles were produced using either acetone or ethyl acetate as the organic solvent and poly(vinyl alcohol) or human serum albumin as the surfactant. This is because the most critical measure of performance of these nanoparticles proved to be their ability to re-suspend after freeze-drying.     

Thermal and Thermo-Oxidative Degradation of Biodegradable Poly(Ester Urethane) Containing Poly(L-Lactic Acid) and Poly(Butylene Succinate) Blocks

A novel biodegradable poly(ester urethane; PEU) was synthesized by chain extension reaction of dihydroxylated poly(L-lactic acid; PLLA) and poly(butylene succinate; PBS) using diisocyanate as a chain extender. The kinetics of thermal and thermo-oxidative degradation of PEU containing PLLA and PBS blocks were studied by thermogravimetric analysis (TGA). TGA results indicated that PEU was more stable in air than in nitrogen and went through a two-stage degradation process irrespective of the experimental atmosphere. Activation energy of each stage was calculated by means of Kissinger, Kim-Park, Friedman, Flynn-Wall-Ozawa, and Kissinger-Akahira-Sunose methods. For the first stage, the activation energy value obtained in air was slightly higher than the corresponding value obtained in nitrogen; and for the second stage, the activation energy showed a much higher value in air than in nitrogen. The Coats-Redfern method was employed to study the degradation mechanism of each stage. The results indicated that the degradation of the first stage follows the P3/4 mechanism irrespective of the experimental atmosphere; the degradation of the second stage of PEU obeys the P1 mechanism in nitrogen while P3/2 in air.     

Thermal and Mechanical Properties of Poly(lactic acid)/Modified Carbon Black Composite

Poly(ethylene glycol) (PEG) was added as a plasticizer to the composite of poly(lactic acid) (PLA) and a modified carbon black (MCB). Among the three different molecular weight (M_n = 1000, 2000, 6000) PEGs used, PEG2000 promoted crystallization of PLA and enhanced the nucleation activity of MCB more efficiently than the other two. The crystallization rate of PLA/PEG2000/3 wt% MCB composite was three times that of PLA. Although a small decrease in tensile strength and modulus of elasticity of the composite was found as the PEG content increased, the elongation at break of the PLA/PEG/MCB composites significantly improved. When the PEG2000 content was 15 wt%, the elongation at break of the blend was 90%, 4.5 times that of the neat PLA.     

Toughened Poly(Trimethylene Terephthalate) by Blending with a Functionalized Metallocenic Poly(Ethylene-Octene) Copolymer

New toughened poly(trimethylene terephthalate) (PTT) materials were obtained by melt blending with maleic anhydride grafted poly(ethylene-octene) (POEg). Rheological properties, mechanical properties, and morphological characteristics of PTT/POEg blends at four different compositions—95/5, 90/10, 80/20, and 70/30—were studied. The melt viscosity of the blends shows a linear decrease on increasing the POEg content. The addition of rubbery POEg to the PTT matrix increases the impact strength, while tensile properties decrease. Scanning electron microscopy (SEM) displayed a very good dispersion of POEg particles in the PTT matrix. Differential scanning colorimetry (DSC) experiments showed that for all samples the melting point was almost constant and the crystallinity did not show obvious differences. SEM results showed shear yielding of the PTT matrix was the major toughening mechanism.     

Toughening of Poly (Butylene Terephthalate) with Epoxy-Filled Poly (Ethylene–Octene) Copolymer

Toughened poly (butylene terephthalate) (PBT) with triglycidyl isocyanurate (TGIC)-filled poly (ethylene–octene) (POE) was prepared by melt reaction extrusion. For retarding the reaction extent between PBT and the epoxy component, the TGIC was first blended with POE to enwrap its reactive epoxy groups. Then, the TGIC-filled POE was used to melt blend with PBT. The Fourier transform infrared (FTIR) spectra showed that no other peaks appeared in the POE/TGIC specimens except for those originally existing in pure POE and TGIC. The rheological results further confirmed that no reaction occurred between the epoxy and the POE matrix. When the POE/TGIC was blended with PBT, a distinct increase of the viscosity suggested that the migration of the TGIC from POE to PBT during the melt processing induced chain extension reactions of PBT. The results obtained from DSC and DMA revealed that the chain extension of PBT induced by the reaction with TGIC restricted the mobility of PBT chains leading to a limitation of the recrystallization-remelting process and an increase of the glass transition temperature of PBT. The mechanical tests showed that the presence of TGIC in the POE phase distinctly improved the toughness of PBT. Compared to the case of a PBT/POE (80/20, wt%/wt%) blend, the elongation at break and impact strength of the system filled with 5 phr TGIC were increased more than three and six times, respectively.     

Preparation and Characterization of Poly(L-lactic acid)/Polybutadiene Block Copolymers

A two-step process to prepare poly(L-lactic acid) (PLLA)/polybutadiene (PB) block copolymers was studied. Melt polymerization was used to prepare poly(L-lactic acid) terminated with hydroxy groups, at the same time hydroxy-terminated polybutadiene and 1,6-hexamethylene diisocyanate were employed to synthesize isocyanate-terminated polybutadiene (ITPB). Then PLLA and ITPB were reacted with different PB/PLLA weight ratios. Consequently, a series of PLLA/PB copolymers with linear or crosslinked chains was obtained. Viscosity of the linear copolymer was measured by an Ubbelohde viscometer. Swelling characteristics and crosslink density of the crosslink copolymer were investigated. Fourier transform infrared and proton nuclear magnetic resonance were used to characterize the structure of the copolymer, and dynamic mechanical analysis (DMA) was applied to characterize its thermal properties. Mechanical property measurements showed that a toughened PLLA polymer was synthesized. Atomic force microscope was utilized to characterize its micro-morphology.     

Characterization of Nano-Structured Poly(D,L-lactic acid) Nonwoven Mats Obtained from Different Solutions by Electrospinning

Two different solvent mixtures, chloroform/dimethylformamide (DMF) and chloroform/ acetone, in 60/40 v/v concentrations, were used to electrospin poly(D,L-lactic acid) (PDLLA). The influence of solvent type, solution concentration, and processing conditions on the morphology and properties of the electrospun mats was studied. The nanofibers characterization was done by scanning electron microscopy (SEM), wide-angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC). The smallest nanofibers’ diameters from both mixtures were obtained from solutions with 5 wt%/v PDLLA concentration using a 1.0 kV/cm electrical field. In general the nanofibers from the chloroform/DMF mixture had smaller diameters than the nanofibers from the chloroform/acetone mixture. However, the latter ones were porous, while the nanofibers from the chloroform/DMF mixtures were not. All the PDLLA nanofibers, independent of solvent mixture, had a very low amount of crystallinity and were composed of very small and imperfect α and β crystals.     

Isothermal Crystallization and Melting Behavior of Composites Composed of Poly(L-lactic Acid) and Poly(glycolic Acid) Fibers

Several composites of poly (L-lactic acid) (PLLA) with poly (glycolic acid) (PGA) fibers were prepared. The isothermal crystallization kinetics and melting behavior of PLLA and all of the composites were characterized by using differential scanning calorimetry. The experimental data were processed by using the Avrami equation. The relative parameters, such as the Avrami exponent and half-time crystallization, revealed that PGA fibers had positive effects on the crystallization of PLLA, but these effects had only a minimal dependence on the PGA fiber content. Moreover, at low isothermal crystallization temperatures (85°C～110°C), recrystallization during the heating scan was observed, which could lower the melting point of the samples to a certain extent.     

Synthesis and Application of a Novel Charring Agent Poly(p-ethylene terephthalamide)

A novel charring agent poly(p-ethylene terephthalamide) (PETA) was synthesized by using terephthaloyl chloride and ethylenediamine through solution polycondensation at low temperature. Poly(p-ethylene terephthalamide) was used together with ammonium polyphosphate (APP) to prepare a novel intumescent flame retardant (IFR) for acrylonitrile–butadiene–styrene (ABS). The thermal degradation behavior and flame retardancy were investigated by thermogravimetric analysis and limiting oxygen index (LOI) tests, and the morphology and structures of residues generated in different conditions were investigated by scanning electron microscopy and Fourier transform infrared spectra. The results showed that PETA could be effective as a charring agent, the flame retardancy of ABS and the weight of residues improved greatly with the addition of IFR. When the content of APP was 25 wt% and PETA was 12.5 wt%, the LOI value of IFR–ABS system was found to be 33, and class V-0 of UL-94 test was passed. The microstructures observed by scanning electron microscope indicated that the charring agent (PETA) can promote formation of uniform and compact intumescent charred layers in IFR–ABS system after burning.     

Tearing and Rheological Properties of Fully Biodegradable Poly(Lactic Acid)/Poly(Ethylene Glutaric-Co-Terephthalate) Copolyester Blends

The tearing and rheological properties of poly(lactic acid) (PLA)/poly(ethylene glutaric-co-terephthalate) copolyester (FP) blends were investigated using a wide range of blending ratios. The tearing strength values of PLA/FP were always significantly higher than that of the PLA specimen. The melt flow indexer and capillary rheometer analyses indicated that the viscous flow became difficult and the melt strength of PLA was improved after the addition of FP. The interactions between the molecular chains of PLA and FP adds FP branching and lengthens the macromolecular chains and the degree of macromolecular entanglement increases. The blends with 5 wt% FP reached the maximum melt strength and minimum flow index n, while the tearing strength approached the maximum level. At higher FP contents, the melt flow properties PLA/FP blends increased and the melt strength decreased, the tearing strength of PLA/FP blends also decreased.     

Characterization of Poly(Vinyl Alcohol) Membranes Cross-Linked by Aldehyde-Substituting Cyclotriphosphazene

A new type of cross-linker, based on cyclotriphosphazene with six aldehyde groups, was used for the cross-linking of poly(vinyl alcohol) membranes. FTIR-ATR analysis indicated that cyclophosphazene reacted with poly(vinyl alcohol) by forming C–O–C bonds. TGA and DTG analysis showed that cross-linking improved the thermal stability. The swelling degree and pervaporation properties of cross-linked PVA membranes were also characterized. With increasing cross-linker concentration, swelling degrees and flux decrease while separation factors increase. Compared with PVA membranes cross-linked by glutaraldehyde, PVA membranes cross-linked by cyclophosphazene exhibited better selectivity and permeation rate.