Colorimetric Determination of Propofol in Bulk form,Dosage Form and Biological Fluids

ABSTRACT

Propofol is coupled with 2, 6-dichloroquinone-4-chlorimide (DCQ) in a reaction buffered at pH 9.6 to give a colored product having an analytically useful maximum at 635 nm. The factors affecting the color generation were optimized and incorporated in the procedure. The reacted propofol has a molar absorptivity of 3.9 × 10^?4 L mol^?1 cm^?1, and Beer's law is obeyed for concentrations 1-5 μg ml^?1 with detection limit 0.25 μg ml^?1. The method was found applicable to biological fluids (plasma and urine) spiked with propofol at concentration levels 1-5 μg ml^?1 for plasma and 1-5 μg 0.5 ml^?1 urine (less sensitivity is obtained with urine volumes above 0.5 ml) with detection limits 0.28 μg ml^?1 for plasma and 0.4 μg 0.5 ml^?1 urine. The average recovery for the commercial preparation (1% w/v propofol emulsion intravenous injection for infusion) was 99.54% with an RSD of 1.05%. The method was validated by an adopted HPLC method. The results obtained by the HPLC method for the commercial preparation were statistically compared with the proposed method and evaluated at the 95% confidence limits.     

A Fluorosensor with Immobilized Cyclodextrin As A Substrate

Abstract

A flow-through optosensor for phenylalanine and tyrosine is described in this paper. The sensor is developed in conjunction with a flow-injection analysis system and uses immobilized β-cyclodextrin as the sensing agent. The analytical performance characteristics of the proposed sensor for analysis of very low levels of phenylalanine and tyrosine were as follows: the detection limits for phenylalanine and tyrosine were 0.20 μg ml^?1 and 8.9 ng ml^?1, respectively. The observed relative standard deviations were 1.03% for 50 μg ml^?1 of phenylalanine (n = 7) and 3.6% for 0.1 μg ml^?1 of tyrosine (n = 7), respectively.     

Selective Kinetic Spectrophotometric Determination of Nitrite in Food and Water

Abstract

A highly selective and sensitive method for the kinetic spectrophothometric determination of sub-microgram amounts of nitrite has been development based on its reaction with Nile blue 2B in acidic medium. The reaction is monitored spectrophotometrically at 595 nm at a fixed time of 4.5 min. The change in absorbance at 595 nm is related to the concentration of nitrite in the range 0.005 - 1.100 μg.ml^?1 The detection limit is 0.001 μg.ml^?1. The relation standard deviation is 1% for 0.020 μg.ml^?1 of nitrite for ten replicate measurements. Most common anions and cations do not interfere. The procedure was applied to the determination of trace amounts of nitrite in sausage and water.     

Determination of Molybdenum in Human Urine by Spectrophotometric Method using Thiazolylazo Compounds as Chromogenic Reagents

ABSTRACT

Four azo compounds based on diazotization of 2-aminobenzothiazole have been synthesized and characterized by elemental analysis as well as different spectroscopic techniques. The potentiality of the prepared compounds as new chromogenic reagents for the spectrophotometric determination of Mo⁶⁺ was studied by extensive investigation of optimum conditions favouring the formation of the coloured complexes. Beers law is obeyed in the concentration range 0.2-8.5 μg ml^?1 whereas Ringbom optimum concentration range was 0.8-7.5 μg ml^?1. The detection limit was 0.05 μg ml^?1. The molar absorptivity and Sandell sensitivity of the formed complexes are calculated. The effect of interfering ions on the determination of Mo⁶⁺ was investigated. The relative standard deviations for six replicate determinations of 5.0 μg ml^?1 of Mo⁶⁺ are 1.23, 1.47, 1.05 and 1.38 % using reagents I, II, III and IV, respectively. The proposed method has been applied to investigate the amount of Mo⁶⁺ in human urine samples. The molybdenum levels found between 0.5-2.1 μg/100 ml.     

Ion-Associates of Alkaloids and Synthetical Psychopharmaca With Cresol Red.

Abstract

Ethylmorphine, morphine, codeine, cocaine, sernyl (PCP), LSD, 3-quinuclidinyl benzilate (BZ) provide, together with Cresol Red, ion-associates that are extractable by chloroform. The extracts of the ion-associates prove the absorption maxima in the interval 405 to 415 nm. Maximum extraction of the analytes of the ion-associates is reached after 4 minutes, taking readings of different pH values in 4 intervals of 1.5. This method allows detect of alkaloids and synthetical psychopharmaca row of quantities between 0.45 μg.ml^?1 and 1.55 μg.ml^?1 and to determine 1.05 μg.ml^?1 to the amount 2.99 μg.ml^?1 of the analytes in the aqueous solutions.     

Square‐Wave Adsorptive‐Stripping Voltammetric Detection in the Quality Control of Fluoxetine

ABSTRACT

A simple and sensitive extraction-spectrophotometric method for the determination of barium and potassium is reported. The 18C6-Barium-Orange II (18C6-Ba-(OR II)₂) and 18C6-Potassium-Orange II (18C6-K-OR II) ternary complexes are quantitatively extracted into dichloromethane and their absorbances are measured at 483 nm. Linear calibration graphs were obtained over the barium concentration range of 0.1-5 μg ml^?1 and potassium concentration range of 1-8 μg ml^?1. The relative standard deviation for 2.0 μg ml^?1 barium and pottasium are, respectively, 4.16% and 3.60%. The interfering effect of a large number of diverse ions on the determination of barium and potassium was studied. The method was applied to a synthetic sample with natural matrix effects of tap water and the results showed high potential of the recommended method for the determination of Ba and K in water samples.     

Integrated Retention/Spectrophotometric Detection Method for the Determination of Formaldehyde

Abstract

An integrated-sensor method for the determination of formaldehyde based on retention of the reaction product of the analyte with p-rosaniline and sulfite in a flow-cell packed with Dowex 1-X-8 anion exchange resin was developed. The method has a good selectivity with a detection limit of 0.3 μg ml^?1 (1 ml sample) or 75 ng ml^?1 (2 ml sample), and a linear range between 1–30 μg ml^?1. The relative standard deviations (n = 11) were 2.8 and 1.3% for 2 and 20 μg ml^?1 formaldehyde, respectively. Depending on the working conditions, the sampling frenquency ranged between 10 and 18 h^?1. The method was applied to the determination of formaldehyde in well water.     

Flow-Injection Chemiluminescence Determination of Fluoroquinolones

ABSTRACT

A new flow-injection CL method was developed for the determination of fluoroquinolones including ofloxacin, norfloxacin, ciprofloxacin and lomefloxacin in pharmaceutical preparations, based on the chemiluminescence reaction of sulphite with cerium(IV) sensitized by these compounds. The linear ranges are 0.04 to 4.0 μg ml^?1 for ofloxacin and 0.4 to 40.0 μg ml^?1 for norfloxacin, ciprofloxacin and lomefloxacin, respectively. The detection limits are 0.016 μg ml^?1 for ofloxacin and 0.16 μg ml ^?1 for norfloxacin, ciprofloxacin and lomefloxacin, respectively. The relative standard deviations (RSD) are 2.1 to 2.6% (n=10) for these fluoroquinolones. The analytical procedure has been applied to the determination of the fluoroquinolones in pharmaceutical commercial formulations. The results are in agreement with those obtained by the official methods.     

Kinetic-Spectrophotometric Determination of Molybdenum(VI) Based on Its Catalytic Effect on the Thionine-Hydrazine Reaction

Abstract

A kinetic method for the determination of trace amounts of Mo(VI) (0.05-4 μg ml^?1) based on its catalytic effect on the reduction of thionine by hydrazine monochloride in strongly acidic media is reported. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of thionine at 605 nm after a fixed time (5 min.). The detection limit of the method is 23 ng ml^?1 and the relative standard deviation (RSD) for 0.05 μg ml^?1 of Mo(VI) is 1.2% (n=7). The method is almost free from interferences, especially from large amounts of tungsten. The procedure was successfully applied to the determination of trace amounts of molybdenum in steel.     

Fluorescent Complexes of Nucleic Acids/8-Hydroxyquinoline/Lanthanum(III) and the Fluorometry of Nucleic Acids

Abstract

The ternary fluorescent complexes of nucleic acids/8-hydroxyquinoline/ lanthanum (III) were studied. Nucleic acids in the study involve natured and thermally denatured calf thymus DNA, fish sperm DNA and yeast RNA. In the range of pH 8.0–8.4 (controlled by NH₃-NH₄Cl buffer) ternary fluorescent complexes are formed which emit at 485.0 nm for calf thymus DNA and at 480.0 nm for yeast RNA (when excited at 267.0 nm) and emits at 483.0 nm for fish sperm DNA when excited at 265.0 nm. Based on the fluorescence reactions sensitive fluorometric methods for nucleic acids were proposed. Using optimal conditions, the calibration curves were linear in the range of 0.4–3.6 μg˙ml^?1 for calf thymus DNA, 0.4–4.0 μg-ml^?1 for fish sperm DNA and 0.4–4.0 μg˙ml^?1 for yeast RNA, respectively. The limits of determination (3σ) were 0.076 μg˙ml^?1 for calf thymus DNA, 0.068 μg˙ml^?1 for fish sperm DNA and 0.329 μg˙ml^?1 for yeast RNA, respectively. Five synthetic samples were determined with satisfaction.

     

Zero-Crossing Derivative Spectrophotometric Determination of Mercury(II) And Palladium(II) with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1-3-thiazolidine and Cetyltrimethylammonium Bromide

Abstract

A method is proposed for the simultaneous determination of mercury(II) and palladium(II) by first-derivative spectrophotometry based on the absorption spectra of their complexes with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1,3-thiazolidine [5-(3,4-methoxyhydroxybenzylidene) rhodanine]. Zero-crossing measurement technique is found suitable for the measurement of the first-derivative value at the specified wavelengths. Mercury(II) (0.4-1.4 μg ml^?1) and palladium(II) (0.08 - 1.8 μg ml^?1) in different ratios have been determined simultaneously. A critical evaluation of the proposed method is performed by statistical analysis of the experimental data.     

Spectrophotometric and Spectrofluorimetric Determination of Famotidine and Ranitidine Using 1,4-Benzoquinone Reagent

ABSTRACT

Spectrophotometric and spectrofluorimetric methods were adopted for the analysis of Famotidine and Ranitidine depending on their reaction with 1,4 Benzoquinone reagent at pH 5.2 and 5.6, respectively. The absorbances of the resulting condensation products were measured at 502 and 508 nm for Famotidine and Ranitidine, respectively. Concentrations adhering to Beer's law were from 40-160 μg.ml^? for Famotidine and from 20-100 μg.ml^? for Ranitidine.

Furthermore the resulting condensation products exhibited fluorescence at 665 nm when excited at 290 nm and the calibration graphs were rectilinear from 0.4-1.4 μg.ml^? for Famotidine and from 0.21 μg.ml^? for Ranitidine.

Different parameters affecting these reactions were thoroughly studied. Also these methods were applied to the pharmaceutical preparations and the results were satisfactory. The validities of the methods were ascertained by the standard addition technique revealing fine results in consideration to the mean recovery percent and standard deviation.

The spectrofluorimetric method was a hundred times more sensitive then the spectrophotometric method. The proposed methods were sensitive, accurate, and precise as statistically compared with the official methods of analysis of Famotidine and Ranitidine.     

Utility of p-chloranilic Acid and 2,3 Dichloro-5,6-dicyano p-Benzoquinone (DDQ) for the Spectrophotometric Determination of Triamterene

Abstract

Two simple and sensitive spectrophotometric procedures are suggested for analysis of triamterene. The first procedure is based on the reaction of triamterene with p-chloranilic acid (p-CA) in methylene chloride to form a highly stable coloured product, exhibiting maximum absorbance at λ 530 nm. Beer's law is obeyed in the range of 40–220 μg.ml^?1 with a mean percentage accuracy of 99.98 ± 0.446. Limit of determination is 20 μg.ml^?1. In the second procedure, the drug is determined via charge transfer complex formation with 2,3 dichloro-5,6-dicyano p-benzoquinone (DDQ) using methylene chloride as a solvent. Here the reaction product has two well defined maxima at 460 nm and 530 nm where each has been utilized for quantitative determination. Beer's law is obeyed in concentration ranges of 25–125 μg.ml^?1 and 25–150 μg.ml^?1 with mean percentage accuracies of 99.92 ± 0.449 and 100.00 ± 0.511 for both maxima. 460 and 530 nm. respectively. Limit of determination is 12.5 μg.ml^?1 at both maxima. Optimum conditions for each procedure have been studied and the stoichiometry of both reactions was ascertained using Job's method of continuous variation. The validity of the suggested procedures was assessed by applying the standard addition technique using the drug capsules. Both procedures are statistically analyzed as compared with BP method for analysis of triamterene (non aqueous titration) revealing good accuracy and precision as indicated by t and F tests.     

Low-Temperature Phosphorescence Analysis of Mebendazole and Related Imidazoles

Abstract

Native low-temperature phosphorescence of mebendazole and flubendazole in ethanol is used for the determination of these imidazoles in anthelmintic preparations with wavelength maxima and detection limits of λ_EXC = 322 nm, λ_EM = 454 nm; 10 ng ml^?1 and λ_EXC = 325 nm, = λ_EM = 455 nm; 5 ng ml^?1, respectively, with linear response up to 8 μg ml^?1 and 9 μg ml^?1, respectively. The structural basis of these phenomena is discussed for both compounds and for related imidazoles and benzimidazoles. Apart from good sensitivity and excellent specificity offered by the technique, the use of cryogenic equipment (liquid nitrogen, special cuvettes, expensive dewar cells) implies some disadvantages for routine analyses.     

Flow Injection Analysis of Famotidine with Spectrophotometric Detection

Abstract

A flow injection determination of famotidine has been described. The method is based on the reaction of the drug with cupric acetate to form a blue coloured complex which shows absorption maxima at 314 nm and 630 nm. For an injection volume of 100 μl calibration graphs were rectilinear from 10- 50 μg. ml^?1 and 50–500 μg.ml^?1 of drug at the two wavelengths respectively. Samples could be analysed at rates upto 60 per hour with a relative standard deviation less than 1.4%. The method was evaluated by analysis of the pure drug and commercial formulations. The results compare well with those obtained by official methods.     

Spectrophotometric and First Derivative Spectrophotometric Determination of Magnesium with 1-Hydroxy-2-Carboxyanthraquinone

Abstract

1-Hydroxy-2-carboxyanthraquinone reacts with magnesium in ethanol-water mixtures to form a red complex having an absorption maximum at 490 nm in alkaline medium. A detailed study of the characteristics of this complex has been carried out and a spectrophotometric method for the determination of magnesium at the 0.4–4.0 μg ml^?1 level is proposed. The method has been sensitized by employing first derivative spectrophotometry. By the use of the derivative approach magnesium can be determined between 0.08–0.40 μg ml^?1. Statistical analysis of the results is also described.     

Fluorimetric determination of mebendazole and flubendazole in pharmaceutical dosage forms after alkaline hydrolysis

The selective and very sensitive fluorimetric determination of mebendazole and flubendazole is based on alkaline hydrolysis and adsorption on Whatman 42 filter paper. Limits of detection are 0.1 μg ml^?1 and 0.5 μg ml^?1, respectively, with linear response sponse up to 10 μg ml^?1 and 50 μg ml^t?1. The fluorescence produced is very stable (λ_em = 460 nm) and the method is applicable to anthelmintic pharmaceutical preparations.     

Determination of Biacetyl by Sensitized Photochemical Kinetic Fluorimetry

Abstract

A new in-situ photochemical kinetic fluorimetric method was proposed for the determination of biacetyl (BI). It is based on the sensitization of BI on the photochemical reaction of amaranth (AM). AM, a nonfluorescent compound was converted into an intensively fluorescent compound in a slightly alkaline medium by the sensitized photochemical reaction, and BI was indirectly determined by monitoring the change of the fluorescence intensity. The determination can be carried out by fixed-time method or tangent method. The kinetic behavior of the reaction and the effects of some experimental conditions were investigated and discussed. The calibration graph was rectilinear from 1.0 μg ml^?1 to 10.0 μg ml^?1 of BI (r = 0.999), the limit of detection was 1.0 ng ml^?1, and the coefficient of variation was 0.44% for 0.90 μg ml^?1 of BI (n = 6). The mechanism for the sensitization of BI was examined and the triplet-triplet energy transfer, in which BI acted as the energy donor and AM as the energy acceptor, was suggested to be the main cause. Its application to real samples has been tested.     

Determination of Morestan Residues in Water and Foodstuffs by Transmitted Room Temperature Solid Phase Spectrophosphorimetry

Abstract

A method for the determination of the pesticide morestan by means of transmitted room temperature solid phase spectrophosphorimetry has been developed. The method is based on the native phosphorescence showed by the morestan when it is fixed in a Whatman No 4 paper as a solid support. The excitation and emission wavelengths were 362 and 527 nm, respectively. The optimum phosphorescent emission was obtained when the delay time was 0.15 ms and the gate time 12.0 ms without need of a heavy atom. The linear dynamic range was between 0.1 and 1.0 μg.ml^?1, and the detection and quantification limits were 0.03 and 0.09 μg.ml^?1, respectively. The precision of the method, expressed as the relative standard deviation of ten samples at the 0.6 μg.ml^?1 concentration level, was 3.0%. The method was applied to the determination of the pesticide in different type of waters, potatoes and vegetables.     

Spectrophotometric Assay of Certain Aminoglycosides Using Cyanoacetamide

Abstract

A simple and sensitive ultraviolet spectrophotometric method has been devised for the determination of amikacin, kanamycin, neomycin and streptomycin in pure form and in some pharmaceutical preparations. The method depends on the nitrosation of the primary amino groups followed by reaction with cyanoacetamide in ammonia medium at 100°C for 30 min, The reaction products exhibit a characteristic absorption. maximum at 270 nm. Beer's law is obeyed within the concentration ranges 4–40 μg ml^?1 for amikacin, kanamycin and neomycin and 8–80 μg ml^?1 for streptomycin with apparent molar absorptivities of about 1.85 × 10⁴ for the first three compounds and 1.3×10⁴ 1. mole^?1.cm^?1 for streptomycin.