Sensitive Spectrophotometric Determination of Copper(II) in the Presence of Manganese

Abstract

This paper recommends a simple and convenient procedure for the determination of copper(II) in the presence of large amounts of manganese. An aqueous solution of hydroxylamine hydrochloride and diluted sulphuric acid was used for dissolution and reduction of MnO₂. The copper(II) was complexed with an ethanolic 0.05% PAN solution in the pH range of 2 - 3 in aqueous medium. The absorbances of copper-PAN complexes are measured at 550 nm where molar absorptivity is 2.10 L.mol^?1.cm^?1.

The complex obeys Beer's Law from 0.1 to 4 ppm. of copper. Manganese(II) up to 1000 ppm. doesn't interfere. The method is sensitive and reproducible.

It has been applied to the analysis of samples containing 0.01 to 5% of copper on manganese dioxide catalysts.     

Preconcentration of Indium(III) from Complex Materials After Adsorption of Its Morpholine-4-dithiocarbamate on Naphthalene or Using Morpholine-4-dithiocarbamate-cetyltrimethylammonium Bromide-naphthalene Adsorbent

Abstract

A highly selective, sensitive and rapid differential pulse polarographic method has been developed for the estimation of trace amounts of indium in standard alloy, ore, synthetic and environmental samples. The morpholine-4-dithiocarbamate of indium(III) is adsorbed on microcrystalline naphthalene in the pH range 3.5–6.4. The metal complex is desorbed with HCl and determined with a differential pulse polarograph (DPP). This metal may alternatively be quantitatively retained on morpholine-4-dithiocarbamate-cetyltrimethylammonium bromidenaphthalene adsorbent packed in a column at a flow rate of 0.5–5.0 ml/min and determined similarly. The detection limit is 0.10 ppm at the minimum instrumental setting (signal to noise ratio = 2). Indium has been determined in the concentration range 0.70–15.0 ppm with a correlation factor of 0.9996 and a relative standard deviation of 0.76% (n = 8). In the column method, the linearity is maintained in the concentration range 0.70–8.5 ppm with a correlation factor of 0.9994 and a relative standard deviation of 0.89% (n = 8). Various parameters, such as the effect of pH, volume of aqueous phase, reagent, and naphthalene concentrations and interference of a large number of metal ions and anions on the estimation of indium have been studied in detail to optimize the conditions for its trace determination in various complex materials.     

Development of a Highly Sensitive and Selective Bismuth Optical Sensor Based on (2E,4E)-5-(2,4-Dinitrophenyl Amino)penta-2,4-dienal

Abstract

An optical sensor based on (2E,4E)-5-(2,4-dinitrophenyl amino)penta-2,4-dienal as ionophore has been developed for the determination of bismuth(III) ions in aqueous solutions. This proposed membrane works on the basis of a cation-exchange mechanism and shows a significant absorbance signal change on exposure to 1 M HCl solution of pH 0.0 containing bismuth ions. The optode membrane shows a reproducible and reversible response toward bismuth in the concentration range 0.2 to 60.5 ppm with a detection limit of 0.095 ppm. This sensor has been used for determination of bismuth in real samples.     

Determination of Gallium By Liquid-Liquid Extraction-Flame Atomic Absorption Spectrometry In Bayer Process Aluminate Solutions

Abstract

The described flame-atomic absorption determination of gallium involves the extraction of 8-hydroxyauinoline-Ga complex and the extraction of galhum as an ion association complex from strong hydrochloric acid into Methyl Isobutyl Ketone (MIBK). Both of the examined extraction systems were found to be workable for gallium determination in aqueous solutions. A comparison of mentioned extraction systems showed that only the second one can be applied for gallium determination in low concentration in aluminate solutions (strong alkaline). Finally, an analytical scheme for gallium determination in aluminate solutions is recommended (extraction of Ga from hydrochloric acid solutions, 3.0-50M, through matrix matched calibration curve). the proposed procedure was found to be simple, selective and accurate.     

Spectrophotometric determination of traces of gallium and indium with 1-(2-pyridylazo)-2-naphthol

1-(2-Pyridylazo)-2-naphthol (PAN) reacts with either gallium or indium at pH 5–6 giving a red complex in an aqueous medium in the presence of N.N-dimethyl-formamide. The maximum absorption of both PAN complexes of gallium and indium in an aqueous solution is at 545 mμ. The gallium-PAN complex shows a characteristic enhancement of color by addition of small amounts of ethers. Based on this selective enhancement reaction, gallium can be determined in the presence of other metals without separation. The results of determining gallium and indium in the presence of each other are reported. Both gallium and indium form M₂(PAN)₃; but in the presence of certain organic solvents, a different gallium complex, Ga(PAN)₅, and the same indium complex, In₂(PAN)₃, are formed. The reaction of PAN with cadmium can be masked by iodide; an example of determining indium in the presence of cadmium is given. The PAN method has a sensitivity of 0.003 μg/cm² for gallium and 0.005μg/cm² for indium and an absorptivity of 24,900 for the Ga-PAN complex and of 24,500 for the In-PAN complex, respectively. The methods have been successfully applied to the determination of both gallium and indium in germanium thin films.     

Simultaneous determination of lead and cadmium in various environmental and biological samples by differential pulse polarography after adsorption of their morpholine-4-carbodithioates onto microcrystalline naphthalene or morpholine-4-dithiocarbamate-CTMAB-naphthalene adsorbent

A highly selective, sensitive and rapid differential pulse polarographic method (DPP) has been developed for the simultaneous estimation of trace amounts of lead and cadmium in standard alloys, biological and environmental samples. The morpholine-4-carbodithioates of the samples were absorbed on microcrystalline naphthalene in the pH range of 5-10 for lead and 3.4-11 for cadmium. The metal complexes were desorbed with 10 ml of 1M HCl and determined simultaneously with a differential pulse polarograph. These metals can alternatively be quantitatively adsorbed on morpholine-4-dithiocarbamate-cetyltrimethylammonium bromide-naphthalene adsorbent packed in a column and determined similarly. The detection limits are 0.14 ppm for Pb and 0.014 ppm for Cd at minimum instrumental settings (signal-to-noise ratio = 2). The linearity is maintained in the concentration ranges of Pb, 0.7-15 ppm and Cd, 0.07-10 ppm with a correlation factor of 0.9997 and relative standard deviations of 0.95 and 0.81%, respectively. Various parameters such as the effect of pH, volume of aqueous phase, and interference of a number of metal ions on the estimation of lead and cadmium have been studied in detail to optimize the conditions for their simultaneous estimation in various biological and environmental samples.     

Column Preconcentration of Palladium Using Phenanthrenequinonedioxime Supported on Naphthalene by Atomic Absorption Spectroscopy

Abstract

A solid chelating compound, phenanthrenequinonedioxime(PQDO) supported on naphthalene provides a rapid and economical means of preconcentration of palladium from the aqueous samples. Palladium forms a complex with PQDO supported on naphthalene in the column at pH 1.2～2.7. The metal complex and naphthalene are dissolved out from the column with 5 ml of dimethylformamide-nitric acid (100+4) and the absorbance is measured atomic absorption spectrometer at 244.7 nm. A calibration curve is linear over the concentration range 1～24 μg of palladium in 5 ml of the final solution. The sensitivity for 1% absorption is 0.126 μg/ml (0.153 μg/ml for the direct AAS method from the aqueous medium). The method has been used for the determination of palladium in various synthetic samples and can be safely applied to the environmental samples too.     

Extraction - Spectrophotometric Determination of Phosphate Using N-Phenylbenzohydroxamic Acid

Abstract

A simple solvent extraction and spectrophotometric method for the determination of micro amount of phosphate (PO₄) is described. Phosphate is selectively separated from associated elements by reacting it with calcium and extracting excess calcium with N-phenylbenzohydroxamic acid (PBHA) at pH 11.3. The excess calcium was determined in ultra-violet and visible region and hence the phosphate content was calculated. The Beer's law is obeyed in the range 0.5 ? 10.0 ppm at 340 nm and 0.25 - 8.0 ppm at 560 nm of phosphate for a fixed amount of calcium (20.0 ppm). These results are also compared with those obtained by atomic absorption spectrophotometry. The method has been applied for the determination of phosphate in pharmaceutical and other samples.     

Pyrocatechol-1-Aldehyde 2-Benzothiazolylhydrazone As Reagent for the Spectrofluorimetric Determination of Nanogram Amounts of Gallium in Urine and Blood Serum

Abstract

A method is developed for the spectrofluorimetric determination of 1–80 ng.ml^?1 of gallium with pyrocatechol-1-aldehyde 2-benzothiazolylhydrazone, in a 50% (v/v) DMSO-Water medium at apparent pH 4.0 (monochloracetic/monochloracetate buffer). Λ_ex = 400nm, Λ_em = 504 nm (corrected). Interferences have been evaluated and the method applied to the determination of gallium in human urine and blood serum samples.     

Design of the Fluoride Ion-Selective Electrode as Tubular Detector for Flow Injection Analysis

ABSTRACT

Design of the fluoride ion-selective electrode (FISE) as the tubular detector used in the flow injection analysis (FIA) has been described. Among other things, this design makes it possible to use various internal contacts. The effect of pH on peak height and detection limit in the pH range from 2.8 to 8.0 has been examined. The effect of flow rate and sample injection volume on peak height and range of linear response has also been examined. The flow rates range from 0.56 mL/min to 4.05 mL/min, while the injection volumes are 100 and 200 μL. The optimum conditions are carrier solution (0.1 M KNO₃ buffer pH 4 and 10^-6 M NaF), flow rate 1.54 mL/min and sample injection volume 100 μL.

Applicability of the FISE as the tubular detector in determination of Fe(III)-ions and AI(III)-ions by flow infection analysis has been examined at pH values of 2.8 and 3.4.     

The Determination of Trace Amounts of Tellurium and Selenium in Gallium Metal

Abstract

Analytical methods have been developed for the separation, concentration and determination of trace quantities of tellurium and selenium from primary and scrap gallium metal. A chloroform extraction is made of the tellurium diethyldithiocarbamate complex at a pH of 8.5. This extraction, in the presence of ammonium citrate, allows the satisfactory determination of tellurium by emission or atomic absorption spectrohcopy. The limit of sensitivity of the method is 0.5 pg of tellurium in 1.0 gram of gallium (0.5 ppm Te).     

Determination of Copper by Faas After Preconcentration with Lead-4-Methylpiperidinedithiocarbamate on Microcrystalline Naphthalene By Solid Phase Extraction

ABSTRACT

By using the Pb-4-methylpiperidinedithiocarbamate complex (Pb(4-MPDC)₂) on microcrystalline naphthalene in a column a method was developed for the preconcentration of copper in water samples prior to its determination by FAAS. In this method, copper in liquid phase quantitatively replaces lead on the Pb(4-MPDC)₂-naphthalene solid phase in the column, forming solid Cu(4-MPDC)₂ complex.

Afterwards, copper on Cu(4-MPDC)₂-naphthalene can be easily eluted by potassium cyanide into the aqueous phase, and the Cu is measured by FAAS. The optimum experimental parameters such as pH, flow rate, sample volume, Pb(4-MPDC)₂-naphthalene ratio, concentration of the potassium cyanide solution and effect of matrix ions for the preconcentration of copper were investigated. The obtained recovery was nearly 100 %, when the enrichment factor was 100 for standard solutions and spiked water samples. The proposed method has been employed for the determination of copper in various standard metal alloys and natural water samples.     

Metformin and Moroxidine Determination With Cu (II)

Abstract

Conductometric titrations of metformin and moroxidine are reported. The procedure is based on the copper-biguanide reaction which gives a pink soluble complex. Studies at several pH values and presence of NH₃ are carried out. NaOH-NH₃ (1:15) are added to 5 ml of biguanide aqueous solution and diluted to 60 ml and titrated with copper sulphate. Concentrations of metformin in 205x10^?4-1,7x10^?3 M range are determined. Foreign species presence is studied too.     

Reversed-Phase High-Performance Liquid Chromatographic Determination of Nicotine in Pesticide Formulations

Abstract

A simple and rapid reversed-phase high-performance liquid chromatographic procedure is described for the determination of nicotine in liquid formulations. Samples are diluted with methanol, and naphthalene is added as the internal standard. Peak height ratios obtained from injections of standard and sample filtrates are used for quanti-tation. An eluting solvent of 0.05M (NH₄)₂ HPO4 (pH 7.5) -methanol (40/60, v/v) at a flow of 2 mL/min gives retention times of 3.13 and 6.88 min respectively for nicotine and naphthalene. Sample analysis can be completed in approximately one hour by the method described as compared to 1.5 days required by the Official AOAC gravimetric method (6.176–6.177).     

Sine-wave polarographic determination of zirconium or niobium in aqueous media

The sine-wave polarographic determination of zirconium in aqueous media was investigated using solutions which were 0.55 – 5.5·10^-3M in zirconyl chloride and 1 M in potassium chloride and had been adjusted to pH 2.0 with hydrochloric acid. It was possible to determine zirconium in the concentration range of 0.05 to 0.4 mg per ml. The sine-wave polarographic behavior of zirconium in aqueous solutions in the pH range 2–3 is discussed. The sine-wave polarographic determination of niobium in aqueous media was investigated using concentrated sulfuric acid containing 5 to 0.1 mg of niobium per ml in a supporting electrolyte of citric acid; the determination of niobium was possible down to 0.1 mg of niobium per ml of concentrated sulfuric acid although the D.C. polarographic method was impractical for the determination of less than 0.5 mg of niobium per ml.     

COMPLEXES OF AMINOPHOSPHONATES PART 9.1 COPPER(II) COMPLEXES OF CIT RIC ACID DERIVATIVES

Abstract

Complex formation between copper(II) and 3-amino-3-phosphonoglutaric acid (Apga), an ambidentate aminophosphonate or citric acid derivative, was studied in aqueous solution by pH-potentiometry and EPR and electronic spectroscopy. Complexation with the parent molecules citric acid and tricarballylic acid was reinvestigated. The stoichiometries and stability constants of the complexes formed in these systems were determined at 25°C at an ionic strength of 0.20 mol dm^?3 (KCl). Stability constant data and spectroscopic results revealed that in the acidic pH range Apga behaves as a citric acid derivative, forming the phosphonate-bridged dimeric species Cu₂A₂H₂, while in the basic pH range, with decreasing proton competition at the amino binding site, it rearranges to yield mononuclear complexes involving aminophosphonate-like (NH₂, PO₃ ^2-, CO₂) coordination.     

Triazene-N-oxides as new type of fluorimetric reagents

Summary The fact that niobium gives orange fluorescence ( _ex ^max 570, _em ^max 540 nm) in both acid and alkali media with 3-(2-hydroxyphenyl)-1-phenyltriazene-N-oxide, has been exploited to develop a simple, sensitive and selective method for the determination of trace amounts of the metal in 50% ethanolic medium. Measurements are made at the pH range of 3.2–5.0. Fluorescence intensity attains the maximum value after 45 min of standing and remains almost unchanged after 24 h. Calibration graph maintains linearity from 50 ppb to 2.2 ppm of the metal. Forty cations and anions are without any effect on the fluorimetric determination of niobium(V). The method has been applied to the analysis of synthetic mixtures.     

Column Chromatographic Preconcentration of Copper in Alloys and Complex Materials Using 9,10 Phenanthrenequinone Monoxime Supported on Naphthalene

Abstract

A solid chelating compound phenanthrenequinone monoxime PQM) supported on naphthalene provides a rapid and economical means of preconcentration and separation of copper from the aqueous samples. Copper forms a complex with PC:: supported on naphthalene in the column at pH 6.1–8.4 with a flow rate of 1 ml/min. The metal complex and naphthalene are dissolved out from the column with 5 ml of DMF and the absorbance is measured at 470 nm against reacent blank. Beer's law is obeyed in the concentration range 0.6 9.6 μg of copper in 5 ml of DMF. The molar absorptivity and sensitivity are 6.3×10⁴ L mol^?1 cm^?1 and 0.001 μg cm^?2 respectively.     

Differential pulse polarography determination of indium after column preconcentration with [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent or its complex on microcrystalline naphthalene

A highly selective, sensitive and economical differential pulse polarographic method has been developed for the determination of trace amount of indium in various samples after adsorption of its 1-(2-pyridylazo)-2-naphthol on naphthalene in the pH range of 6.5-11.5. After filtration, the solid mass is shaken with 8 ml of 1 M hydrochloric acid and indium is determined by differential pulse polarography (DDP). Indium can alternatively be quantitatively adsorbed on [1-(2-pyridylazo)-2-naphthol]-naphthalene adsorbent packed in a column and determined similarly. The detection limit is 0.2 ppm (signal to noise ratio=2) and the linearity is maintained in the concentration range 0.8-125 ppm with a correlation coefficient of 0.9994 and relative standard deviation of +/-0.96%. Characterization of the electroactive process included an examination of the degree of reversibility. Various parameters such as the effect of pH, volume of aqueous phase and interference of a number of metal ions on the determination of indium have been studied in detail to optimize the conditions for determination in various samples.     

Complex Formation Reactions of Dimethyltin(IV) with Some Zwitterionic Buffers

Equilibrium studies in aqueous solution are reported for dimethyltin(IV) complexes of zwitterionic buffers, such as bicine and tricine (L). Stoichiometry and stability constants for the complexes formed were determined at 25°C and ionic strength 0.1M NaNO₃. The results showed the best fit of the titration curves were obtained for complexes MLH, ML, ML₂, MLH_-1, and MLH_-2 with the hydrolysis products of the dimethyltin(IV) cation. The bonding sites of the dimethyltin(IV) complexes with bicine and tricine at different pH were characterized in the solid state by elemental analyses, FTIR, and TG analysis. The molecular formula of the complexes synthesized at pH=3.0 is [(CH₃)₂Sn(L)(H₂O)]Cl while in neutral and alkaline media the hydrolytic species are formed.