Carbon-Filled Polymer Paste Ion-Selective Probes

Abstract

Inexpensive, disposable, carbon-filled polymer paste electrodes activated by a superficial layer of electro-active powder are reported. Sensors for silver, copper, lead and cadmium, halides, nitrate, pH and redox were thus prepared.     

Ion Selective Electrodes Based on Brilliant Green Tetrathiocyanatezincate(II)

Abstract

Liquid state, heterogeneous silicone rubber and carbon paste electrodes based on Brilliant green tetrathiocyanatozincate(II) have been prepared and studied. The liquid state electrode, consisting of a 10^?3 M solution of Brilliant green tetrathiocyanatozincate(II) in o-dichlorobenzene supported on lightly cross-linked natural rubber, was the most satisfactory. This electrode responded rapidly when placed in 10^?4 to 10^?1 M solutions of zinc containing a twenty-fold excess of thiocyanate. The potential concentration slope (-29.5 mV per decade change in concentration) was that 2-expected for response to Zn(SON)₄ ²-. The silicone-rubber and carbon paste electrodes also gave near-Nernstian response, but responded more slowly.     

Flow Injection Analysis of Phenolic Compounds with Carbon Paste Electrodes Modified with Tyrosinase Purchased from Different Companies

Abstract

Tyrosinase-modified carbon paste electrodes were prepared using lyophilised powder of the enzyme purchased from different companies. The selectivity of these electrodes for nine phenolic compounds, including six substituted catechols, has been studied. The signals obtained for catechol were always higher than those found for other phenolic compounds. Cyclic voltammetry and flow injection measurements indicated that the response of the tyrosinase-modified carbon paste electrodes was limited by the rate of the enzymatic oxidation of catechols. Different approaches of paste electrode preparation have been studied and compared. Direct mixing of enzyme into the graphite powder doped with the osmium based mediator, resulted in the highest sensitivity for the studied substrates. However, substrate selectivity was found to be dependent on the source of enzyme used for electrode preparation.     

Applications of Chemically Modified Electrodes to Analysis of Metal Ions

Abstract

A carbon paste electrode containing chemically modified graphite has been fabricated and applied to the analysis of silver ion in aqueous media. Utilizing complexation and subsequent precipitation steps, it is shown that one can preconcentrate and then analyze for metal ions at low concentrations using these electrodes.     

Enantioselective,Potentiometric Carbon Paste Electrodes Based on C60 Derivatives as Chiral Selectors for the Enantioanalysis of S‐Clenbuterol

Abstract

Three enantioselective, potentiometric carbon paste electrodes (EPCPEs) based on carbon paste impregnated with (1,2‐methanofullerene C60)‐61‐carboxylic acid (I), diethyl (1,2‐methanofullerene C60)‐61‐61‐dicarboxylate (II), and tert‐butyl (1,2‐methanofullerene C60)‐61‐carboxylic acid (III) are reported. Response characteristics showed that the proposed electrodes could be reliably used in the assay of S‐clenbuterol raw material and in serum samples. The surfaces of the electrodes are stable and easily renewable by simply polishing on an alumina paper.     

Fabrication of Porous Pseudo-Carbon Paste Electrode as a Novel High-Sensitive Electrochemical Biosensor

Abstract

Porous pseudo-carbon paste electrode (PPCPE) as a novel high-sensitive electrochemical biosensor was fabricated by mixing polymethyl methacrylate (PMMA) microspheres for use as the template, graphite powders for the filler, and pyrrole as the precursor of the polymer which acted as the paste. After the polymerization of pyrrole catalyzed by Fe³⁺, the PMMA microspheres were removed to form PPCPE. The pore size was determined by SEM observations, with diameters ranging from 2 to 5 µm. The anodic stripping voltammetry response of DNA indicated that the adsorption of oligonucleotide on PPCPE was enhanced. The PPCPE was easy to preserve and had a good reusability in comparison with that of a pure carbon paste electrode (CPE) and a carbon nanotube-modified carbon paste electrode (CNTPE). The detection limits of guanine and adenine were 20 nM and 8 nM, respectively.     

Utilization of Maltodextrin‐Based Enantioselective,Potentiometric Membrane Electrodes for the Enantioselective Assay of S‐Flurbiprofen

Abstract

Three enantioselective, potentiometric membrane electrodes (EPMEs) based on carbon paste impregnated with different maltodextrins [dextrose equivalent (DE) (DE 4.0–7.0 (I), 13–17 (II), 16.5–19.5 (III)], were proposed as chiral selectors for the assay of S‐flurbiprofen raw materials and from its pharmaceutical formulation, Froben 100^® tablets. The best response and enantioselectivity were obtained when maltodextrin with lower DE was used for the electrode design. The three EPMEs showed very low detection limits. The surfaces of the electrodes are easily renewable by simply polishing on an alumina paper.     

Electrochemical behavior of small biological molecules at organic donor—acceptor electrodes in aqueous media

The electrochemical behavior of NADH, xanthine, uric acid, 6-mercaptopurine, 6-thioxanthine, dopamine and ascorbic acid was investigated at the organic metal-like polymer paste electrodes, tetrathiafulvalene- and N-methylphenazene-tetracyanoquinodimethane. The reactivity of small biological molecules at polymer paste electrodes is generally lower than at most active graphite electrodes. Typical detection limits of about 10^?5 M and the typical upper limit of linearity of 10^?3 M are observed for the compounds studied.     

Room Temperature Ionic Liquid Carbon Nanotube Paste Electrodes: Overcoming Large Capacitive Currents Using Rotating Disk Electrodes

The voltammetric response of graphite or carbon nanotube paste electrodes, which incorporate the room temperature ionic liquid, N‐butyl‐N‐methyl pyrrolidinium bis(trifluoromethylsulfonyl) imide or [C₄mpyrr][NTf₂], (RTIL‐CNTPE and RTIL‐CPE respectively) as the binder, towards anionic, cationic and neutral redox probes is examined and compared to conventional paste electrodes which use mineral oil as the binder. The RTIL paste electrodes are found to suffer from very large background currents due to capacitive charging. This is exacerbated further when CNTs are combined with RTILs in the paste. The large charging currents obscure any Faradaic processes of interest, especially at low analyte concentrations. By employing steady state voltammetry at a rotating disk electrode made of the RTIL pastes this problem can be overcome. This allows the electroanalytical properties of these interesting electrode substrates, which combine the attractive properties of CNTs with RTILs to be further explored and developed.     

Influence of inner transducer properties on EMF response and stability of solid-contact anion-selective membrane electrodes based on metalloporphyrin ionophores

The performance of solid-contact coated-wire-type electrodes with plasticized poly(vinyl chloride) membranes containing metalloporphyrins as anion-selective ionophores is reported. The membranes are deposited on transducers based on graphite pastes and graphite rods. The hydrophobicity of the underlying conductive transducer surface is found to be a key factor that influences the formation of an aqueous layer beneath the polymer film. Elimination of this ill-defined water layer greatly improves the electrochemical properties of the ion-sensors, such as electromotive force stability and lifetime. Only highly lipophilic electrode substrates, namely graphite paste with mineral oil, were shown to prevent the formation of aqueous layer underneath the ion-sensing membrane. The possibility of employing Co(III)-tetraphenylporphyrin both as NO₂ ⁻ selective ionophore and as electron- and ion-conducting species to ensure ion-to-electron translation was also discussed based on the results of preliminary experiments.     

Tropolone Modified Carbon Paste Electrodes For Trace Measurements of Tin

Abstract

Tin-sensitive chemically modified electrodes were constructed by incorporating the ligand tropolone into the carbon paste matrix. Tin is rapidly collected onto the electrodes and the resulting surfaces are characterized by cyclic and differential pulse voltammetry. the differential pulse peak current, at-0.81V, is ca. 40-fold larger than the corresponding peak at the plain carbon paste electrode. Linear calibration curves are obtained for tin concentrations ranging from 4 to 52 mg/l. the detection limit is 0.2 mg/l. Rapid renewal of the surface allows use of a single electrode in multiple determinations. the relative standard deviation (at the 7 mg/l level) is 2.0%. Interference effects are reported.     

Electrocatalytic Activity of Bamboo‐Structured Carbon Nanotubes Paste Electrode Toward Hydrogen Peroxide

Abstract

In this report, we describe the finding that bamboo‐structured carbon nanotubes (CNT) showed superior electrocatalytic activity toward hydrogen peroxide. The slope of the calibration curve for hydrogen peroxide obtained with the bamboo‐structured CNT paste electrode was more than 20 times as large as the slopes obtained with hollow‐structured CNT paste and glassy carbon electrodes at an operating potential of ?0.1 V, with no interfering reactions. Incorporation of glucose oxidase within the bamboo‐structured CNT paste electrode allows the selective detection of glucose in the presence of common interferents without using any permselective membranes. This excellent ability of the bamboo‐structured CNT paste electrode toward hydrogen peroxide is applicable to the development of other enzymatic biosensors.     

Enantioanalysis of Butaclamol Using Enantioselective Potentiometric Electrodes

Abstract

Three enantioselective, potentiometric electrodes were proposed for the enantioanalysis of butaclamol. The electrodes were based on immobilization of maltodextrins (MDs) of different dextrose equivalences [4.0–7.0, I; 13–17, II; 16.5–19.5, III] into carbon paste. The electrodes based on MD I and II were used for the enantioanalysis of S-butaclamol within linear concentration ranges of 10^?10 to 10^?7 and 10^?10 to 10^?8, respectively, with slopes of 51.20 and 57.59 mV/decade of concentration; whereas the electrode based on MD III was used for the enantioanalysis of R-butaclamol within a linear concentration range between 10^?10 and 10^?7 with a slope of 58.50 mV/decade of concentration. Recoveries greater than 90% were recorded for the enantioanalysis of butaclamol in synthetic and urine samples.     

Nanocarbon Paste Electrodes

The electrochemical behaviour of carbon paste electrodes prepared using nanocarbon and mineral oil was investigated and the results contrasted with different carbon and carbon pastes electrodes. The composition of carbon paste was studied by performing cyclic voltammetry performed in 0.1 M KCl solution in the presence of 4.0 mM Ru(NH₃)₆Cl₃, a well‐characterized redox system commonly used to test the electrode behaviour. After optimisation of the paste composition, the sensors chosen were tested for the analysis and characterization of three different systems: Ru(NH₃)₆^3+/2+, FcCH₂OH/FcCH₂OH⁺ and acetaminophen. The ability to obtain high quality voltammetry from the nanocarbon electrode was demonstrated and simulation of the voltammetry allowed the extraction of electrode kinetic parameters with high precision.     

Stripping voltammetric determination of silymarin in formulations and human blood utilizing bare and modified carbon paste electrodes

Silymarin is one of the most powerful natural substances that have the ability to protect and rebuild the liver cells damaged by alcohol and other toxic substances. Silymarin showed two irreversible anodic peaks in buffered solutions (pH 2.5-8.0) at either the bare carbon paste electrode or the montmorillonite-Ca modified carbon paste one. These two peaks have been attributed to oxidation of the two phenolic OH groups at positions C-20 and C-7 of silymarin molecule. A square-wave adsorptive anodic stripping voltammetry method was optimized for determination of silymarin utilizing the bare and the modified carbon paste electrodes. The method was fully validated and successfully applied for the determination of silymarin in commercial formulations and human serum without prior extraction utilizing both carbon paste electrodes. Limits of quantitation of 1 × 10⁻⁷ and 7 × 10⁻⁹ mol L⁻¹ silymarin have been achieved in bulk form or in formulations while 2 × 10⁻⁷ and 8 × 10⁻⁹ mol L⁻¹ silymarin were achieved in spiked human serum utilizing the bare carbon paste electrode and the modified one, respectively. The two electrodes exhibited excellent selectivity towards silymarin even in the presence of 10²to 10³-fold excess of its co-formulated drugs, common excipients, and common metal ions. The pharmacokinetic parameters of silymarin in plasma of healthy human volunteers were estimated following the administration of a single oral dose of 120 mg silymarin utilizing the modified carbon paste electrode. The estimated pharmacokinetic parameters were favorably compared with those reported in literature.     

Construction and performance characteristics of new ion selective electrodes based on carbon nanotubes for determination of meclofenoxate hydrochloride

This work offers construction and comparative evaluation the performance characteristics of conventional polymer (I), carbon paste (II) and carbon nanotubes chemically modified carbon paste ion selective electrodes (III) for meclofenoxate hydrochloride are described. These electrodes depend mainly on the incorporation of the ion pair of meclofenoxate hydrochloride with phosphomolybdic acid (PMA) or phosphotungestic acid (PTA). They showed near Nernestian responses over usable concentration range 1.0 × 10⁻⁵ to 1.0 × 10⁻² M with slopes in the range 55.15–59.74 mV (concentration decade)⁻¹. These developed electrodes were fully characterized in terms of their composition, response time, working concentration range, life span, usable pH and temperature range. The electrodes showed a very good selectivity for Meclo with respect to a large number of inorganic cations, sugars and in the presence of the degradation product of the drug (p-chloro phenoxy acetic acid). The standard additions method was applied to the determination of MecloCl in pure solution, pharmaceutical preparations and biological samples. Dissolution testing was also applied using the proposed sensors.     

A Novel DNA Probe Based on Molecularly Imprinted Polymer Modified Electrode for the Electrochemical Monitoring of DNA

A DNA probe that was based on methylene blue (MB) imprinted polyvinyl pyridine polymer (MIP) modified carbon paste electrodes were developed for the first time for electrochemical monitoring of DNA. Probes were built up by adsorbing MB onto modified electrodes prior to DNA immobilization. It was shown that DNA strongly immobilizes on MIP modified electrodes when MB was adsorbed in advance of DNA immobilization. The performance of the MB imprinted polymer modified carbon paste electrodes (MIP‐CPE) to rebind the template molecule (MB) were compared to those of control polymer modified (non‐imprinted polymer NIP‐CPE) and bare (CPE) electrodes. Electrochemical signal resulting from the oxidation of guanine moiety of the immobilized probe DNA was high enough on the constructed platform, implicating that probes of this kind could be favorably used for DNA analysis. These probes exhibited high selectivity for its complementary DNA sequences (target). HBV‐DNA hybridization was studied to evaluate the selectivity of the probes for complementary, non‐complementary and mismatch sequences. The detection limit of the probe for the target DNA was 8.72 µg/mL (1.38 µM), which was better than those attained by some earlier DNA sensor studies.     

Polarography in Propylene Carbonate: Preliminary Considerations

Abstract

A preliminary investigation is reported of a relatively new solvent for polarography. Its aprotic nature, stability and high dielectric constant should prove useful for studies of organic and inorganic compounds. Preparation and stability of salt bridges and reference electrodes are described. Behavior of dropping mercury, pyrolytic graphite and platinum indicator electrodes is described.     

Electrochemical Determination of Uric Acid,Dopamine and Tryptophan at Zinc Hexacyanoferrate Clay Modified Electrode

A Cameroonian smectite clay has been transformed into Zn²⁺ homoionic form and then used to prepare film modified glassy carbon electrodes and carbon paste electrodes. These electrodes containing Zn²⁺ were exploited to prepare a mixed valence zinc hexacyanoferrate (ZnHCF). Cyclic voltammetry has been employed to monitor the in situ growth of ZnHCF on clay modified electrodes. Although interesting electrocatalytic properties toward UA were observed with these modified electrodes, the modified carbon paste electrodes were the most suitable for dopamine, uric acid and tryptophan detection and exhibited for these analytes extended linear range, high sensitivities, selectivity and low limit.     

Integrated moulded polymer electrodes for performing conductivity detection on isotachophoresis microdevices

The feasibility of using integrated injection moulded polymer electrodes as drive and detection electrodes for performing miniaturised isotachophoresis (ITP) separations with conductivity detection has been demonstrated. Injection moulded electrodes were produced from three different grades of carbon-filled polymer. Two of the electrode designs were found to be suitable for performing on-chip conductivity detection. The high-voltage characteristics of the microdevices were found to be suitable for performing ITP, with a power dissipation up to 1.4 W m⁻¹ being achieved. Three model separations are presented to demonstrate the separation capability of the miniaturised injection moulded devices. Three anionic dyes, two inorganic anions and a mixture of eight alkaline earth, transition and lanthanide metal cations were analysed.