RuO2/Co3O4 thin films prepared by spray pyrolysis technique for supercapacitors

RuO₂/Co₃O₄ thin films with different RuO₂ content were successfully prepared on fluorine-doped tin oxide coated glass plate substrates by spray pyrolysis method, and their capacitive behavior was investigated. Electrochemical property was performed by cyclic voltammetry, constant current charge/discharge, and electrochemical impedance spectra. The capacitive performance of RuO₂/Co₃O₄ thin films with different RuO₂ content corresponded to a contribution from a main pseudocapacitance and an additional electric double-layer capacitance. The specific capacitance of pure Co₃O₄, 15.5%, 35.6%, and 62.3% RuO₂ composites at the current density of 0.2 A g⁻¹ were 394 ± 8, 453 ± 9, 520 ± 10, and 690 ± 14 F g⁻¹, respectively; 62.3% RuO₂ composite presented the highest specific capacitance value at various current densities, whereas 35.6% RuO₂ composite exhibited not only the largest specific capacitance contribution from RuO₂ (C _sp ^RuO2) at the current density of 0.5, 1.0, 1.5, and 2.0 A g⁻¹ but also the highest specific capacitance retention ratio (46.3 ± 2.8%) at the current density ranging from 0.2 to 2.0 A g⁻¹. Electrochemical impedance spectra showed that the contact resistance dropped gradually with the decrease of RuO₂ content, and the charge-transfer resistance (R _ct) increased gradually with the decrease of RuO₂ content.     

The New Fluorescence Enhancement System Eu<Superscript>3+</Superscript>-ARADE-HMTM-Al<Superscript>3+</Superscript> and its Analytical Application

A new bis-Schiff base ligand, N,N-bis-(4-N-aminothiourea-2-amylidene)-4,4-diaminodiphenyl ether (ARADE), was synthesized. Its complex with Eu³⁺ in DMF emits the intrinsic fluorescence of Eu³⁺. The fluorescence intensity of the Eu³⁺-ARADE system was enhanced about 60-fold by the addition of hexamethylene tetramine (HMTM) and potash alum. This is a new fluorescence enhancement phenomenon. The excitation and emission wavelengths are 375nm and 615nm, respectively. Under optimal conditions, the fluorescence intensities vary linearly with the concentration of Eu³⁺ in the range of 7.8×10^–9–1.75×10^–5mol·L^–1 with a detection limit of 5.2×10^–9mol·L^–1, or with the concentration of Al³⁺ in the range of 3.1×10^–7–9.7×10^–5mol·L^–1 with a detection limit of 2.7×10^–7mol·L^–1. The interferences of some rare earth metals and other inorganic ions were described. This method was applied to the determination of Eu³⁺ in high purity yttrium oxide and the analysis of Al³⁺ in alloy steel standard samples. The mechanism of fluorescence enhancement was also studied.     

Effects of La<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> on outward potassium channels in Vicia guard cells

Effects of La³⁺ and Eu³⁺ on outward potassium channels (K_out⁺) in Vicia guard cells have been studied by patch clamping technique. Extracellular La³⁺ inhibited K_out⁺ currents with a half-inhibition concentration (IC₅₀) of 81 μmol·L⁻¹. Interestingly, intracellular La³⁺ activated K_out⁺ currents at a free concentration of 1.13 × 10⁻¹⁴ mol·L⁻¹, and inhibited K_out⁺ currents at a free concentration of 5.86 × 10⁻¹⁴ mol·L⁻¹. Extracellular Eu³⁺ also activated K_out⁺ currents at concentrations of 10 μmol·L⁻¹ and 50 μmol·L⁻¹, and inhibited K_out⁺ currents at concentrations of more than 1 mmol·L⁻¹. The effects of La³⁺ and Eu³⁺ on K_out⁺ currents may contribute to regulation of the plant water status, which may be one of the mechanisms of the biological effect of rare earth elements.     

Distribution of luminescence excitation energy between Eu<Superscript>3+</Superscript> and Tb<Superscript>3+</Superscript> ions fixed in a perfluorosulfonic membrane

Ion-exchange modification of MF-4SK perfluorosulfonic membranes with Eu³⁺ and Tb³⁺ cations was realized. The state of cations in the membrane was studied by X-ray photoelectron spectroscopy. Special features of the luminescence of the resulting systems point to preferential excitation energy transfer from europium to terbium.     

Extraction chromatographic study on the separation of Am<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> using ethyl-BTP as the extractant

Ethyl-substituted bis-triazinylpyridine (Et-BTP), a nitrogen containing soft-donor extractant, was used in investigations pertaining to the separation of Am³⁺ and Eu³⁺ from dilute nitric acid feed solutions by extraction chromatography using XAD-4 as the inert support, chlorinated dicarbollide as the modifier and 2-nitrophenyloctylether (NPOE) as the diluent. After carrying out a series of experiments, the optimum composition of the extractant mixture for the resin was found out to be 0.1 M Et-BTP and 0.025 M CCD in NPOE. Separation factor values were encouraging to carry out subsequent batch uptake studies at varying nitrate ion concentration which indicated favourable separation behaviour up to NaNO₃ concentration of 2 M. Column studies have been carried out and conditions for elution and separation of Am³⁺ from Eu³⁺ have been found out. Long term stability of the resin was also investigated.     

Spectral Hole-Burning in Femtosecond Laser-Irradiated Eu<Superscript>3+</Superscript>-Doped Aluminosilicate Glasses

We studied the persistent spectral hole-burning (PSHB) of the Eu³⁺-doped Al₂O₃-SiO₂ glasses, prepared by a sol–gel process, exposed to femtosecond laser pulses. The spectral holes were burned in the excitation spectra of the ⁷F₀⁵D₀ transition of Eu³⁺ ion. The depth and width of the burned holes were 15% and 2.5 cm^–1 fwhm at 7 K, respectively. The burned hole is stable up to room temperature. Fluorescence line narrowing spectra showed that Eu³⁺ ions were located in two different sites.     

Detection of up-conversion in nano-structure BaTiO<Subscript>3</Subscript> co-doped with Er<Superscript>3+</Superscript> and Yb<Superscript>3+</Superscript> ions

Nano-structure pure barium titanate BaTiO₃ (BT) and (BT) co-doped with constant concentration of Er³⁺ ions and different concentrations of Yb³⁺ ions were prepared using sol–gel method. XRD results confirmed that the pure sample was found to crystallize in tetragonal phase by sintering at 750 °C for 1 h. All major peaks corresponding to perovskite BT phase appeared. Efficient infrared-to-visible up-conversion is reported in the doped samples. The conversion process and results in the generation of visible emissions are discussed. Up-conversion efficiency for red emission predominates in doped samples. Results illustrate the large potential of this class of materials for photonic applications in optoelectronics devices.     

Thermoanalytical study of precursors for In<Subscript>2</Subscript>S<Subscript>3</Subscript> thin films deposited by spray pyrolysis

Thermal decomposition of precursors for In₂S₃ thin films obtained by drying aqueous solutions of InCl₃ and SC(NH₂)₂ at the In:S molar ratios of 1:3 (1) and 1:6 (2) was monitored by simultaneous TG/DTA/EGA-FTIR measurements in the dynamic 80%Ar + 20%O₂ atmosphere. XRD and FTIR were used to identify the dried precursors and products of the thermal decomposition. The precursors 1 and 2 are complex compounds, while in 2 free SC(NH₂)₂ is also present. The thermal degradation of 1 and 2 in the temperature range of 30–900 °C consists of four mass loss steps, the total mass loss being 89.1 and 78.5%, respectively. According to XRD, In₂S₃ is formed below 300 °C, crystalline In_2.24(NCN)₃ is detected only in 1 above 520 °C and In₂O₃ is the final decomposition product at 900 °C. The gaseous species evolved include CS₂, NH₃, H₂NCN, HNCS, which upon oxidation yield also COS, SO₂, HCN and CO₂.     

Water-soluble polymers as chelating agents for the deposition of Er<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript>:LiNbO<Subscript>3</Subscript> waveguiding films

Compared to other oxide materials, the sol-gel deposition of an optically transparent LiNbO₃ waveguiding film of sufficient thickness (approx. 1?μm) is complicated by the presence of a highly hydrolyzing Nb(V) in the starting solution. Thicker films require more concentrated solutions that are not easily achieved for such ions. This problem may be solved using strong chelating agents such as water-soluble polymers. To prepare a stable Er(III)/Yb(III)/Li(I)/Nb(V)/2-methoxyethanol solution with high metal concentration, we tested three such polymers: polyethylene glycol (PEG), polyacrylic acid (PAA) and polyvinyl alcohol (PVA), and compared them with already used polyvinylpyrrolidone (PVP). The solutions were spin-coated on crystalline sapphire substrates under a multi-step heating-deposition regime. Apart from Er³⁺/Yb³⁺ photoluminescence properties, we evaluated the influence of the film microstructure (SEM, AFM) on optical transparency and waveguiding ability in the UV/Vis/NIR region (transmission and m-line spectroscopy). Among the newly tested polymers, only PEG was able to prevent Nb(V) hydrolysis up to a maximum metal concentration of 0.6?mol/L. For PEG and PVP, the crystallization temperature of the deposited films (between 700?°C and 1000?°C) was compared. After further optimization of the heating-deposition process, we were able to prepare a transparent Er³⁺/Yb³⁺:LiNbO₃ film thick enough to guide an optical signal in the NIR region. Thus, the use of PEG results is one of the very few non-hydrolytic sol-gel methods suitable for the preparation of not only luminescent, but also waveguiding Er³⁺/Yb³⁺:LiNbO₃ structures.

Open image in new window

     

UV excited green luminescence of SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Dy<Superscript>3+</Superscript> nanophosphor

Eu, Dy co-doped strontium aluminate nanophosphors were prepared by the combustion synthesis method. Their structure and morphology were investigated by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy (TEM), and Fourier transform infrared spectroscopy. According to the XRD and the TEM analysis, the average crystallite size was found to be in the nanometer range. The phase structure of the prepared nanophosphor is consistent with a standard monoclinic phase with a space group P2₁. The prepared SrAl₂O₄:Eu²⁺, Dy³⁺ nanophosphor emitted green light with a peak at 510 nm showing blue shift, which is due to the reduction in the particle size. Two distinct peaks were observed in the ML intensity versus time curve. The two peaks in ML indicate the presence of charge transfer in an ML process.     

Intercalation of cytosine into Eu<Superscript>3+</Superscript>-doped hydrocalumite and their fluorescent responses

Intercalation of cytosine into Eu³⁺-doped hydrocalumites and the fluorescence of the Eu³⁺-doped hydrocalumite response to cytosine has been investigated. XRD patterns showed that the basal spacing of Eu-doped hydrocalumite obviously increased after it exposed to various content of cytosine, revealing the intercalation of cytosine into Eu³⁺-doped hydrocalumite. TG-DSC curves and IR spectra of the intercalated samples are different from that of the Eu-doped hydrocalumite and cytosine, indicating the interaction between the Eu³⁺-doped hydrocalumite and cytosine. Fluorescent spectra suggested that the fluorescent changes of Eu³⁺-doped hydrocalumite depended on the concentration of cytosine solution. This fluorescent change would be potential application in biological probe in view of the biocompatibility of Ca²⁺ ions and the fluorescence of Eu³⁺ ions. Moreover, the Eu³⁺-doped hydrocalumite would be a healthy and cheap fluorescent material applied in biology or healing drugs fields.     

Long-term cycling and stability of crystalline WO3 electrochromic thin films prepared by spray pyrolysis

Journal of Solid State Electrochemistry - WO3 thin films with improved electrochromic durability were deposited by pneumatic spray pyrolysis technique on top of FTO substrates; tungsten...     

Eu<Superscript>3+</Superscript>-doped LaPO<Subscript>4</Subscript> and LaAlO<Subscript>3</Subscript> nanosystems and their luminescence properties

Eu³⁺ ion-doped LaPO₄ nanowires or nanorods have been successfully synthesized by a simple hydrothermal method. The influence of varying the hydrothermal and subsequent sintering conditions on the morphology and structure of the LaPO₄ host has been investigated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). For comparison, the Eu³⁺ ions were also doped into monoclinic monazite LaPO₄ nanoparticles and perovskite LaAlO₃ nanoparticles. The relative intensities of the emission lines of the LaPO₄:Eu³⁺ nanosystems were essentially independent of their shape. The optimal doping concentrations in the monoclinic LaPO₄ and perovskite LaAlO₃ nanosystems were determined to be about 5.0 and 3.5 mol%, respectively. Under appropriate UV-radiation, the red light emitted from LaAlO₃:Eu³⁺ (3.5 mol%) was brighter than that from LaPO₄:Eu³⁺ (5.0 mol%) nanomaterial, resulting from differences in their spin-orbit couplings and covalence, which indicates that the nanoscale LaAlO₃ is a promising host material for rare earth ions. Electronic Supplementary Material  Supplementary material is available for this article at and is accessible for authorized users. Supported by the National Natural Science Foundation of China (Grant Nos. 20873039 & 90606001), Hunan Provincial Natural Science Foundation (No. 07jj4002), and the Students Innovation Training Fund of Hunan University     

Photocatalysis enhancement of CaAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Nd<Superscript>3+</Superscript>@TiO<Subscript>2</Subscript> composite powders

CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were synthesized by a sol–gel method under mild conditions (i.e. low temperature and ambient pressure). The as-prepared powders were characterized by transmission electron microscopy (TEM) and analyzed by X-ray diffraction (XRD). The photocatalytic behavior of the TiO₂-base surfaces was evaluated by the degradation of nitrogen monoxide gas. It suggested that CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were composed of anatase titania and that CaAl₂O₄:Eu²⁺, Nd³⁺. TiO₂ particles were deposited on the surface of CaAl₂O₄:Eu²⁺, Nd³⁺ to form uniform film. CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders exhibited higher photocatalytic activity compared with pure TiO₂ under visible light. And the result also clearly indicated that the long afterglow phosphor absorbed and stored lights for the TiO₂ to remain photocatalytic activity in the dark.     

Eu<Superscript>3+</Superscript>-fluorescence properties in nano-crystallized SnO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> glass-ceramics

Fluorescence and spectral hole burning properties of Eu³⁺ ions were studied in nanocrystals-precipitated SnO₂-SiO₂ glasses. The glasses were prepared to contain various amount of Eu₂O₃ using the sol-gel method, in which SnO₂ nanocrystals were precipitated by heating in air. In the glasses containing Eu₂O₃ less than 1%, the Eu³⁺ ions were preferentially doped in the SnO₂ nanocrystals and their fluorescence intensities were enhanced by the energy transfer due to the recombination of electrons and holes excited in SnO₂ crystals. The SnO₂ nanocrystals-precipitated glasses exhibited the persistent spectral holes with the depth of ∼25% of the total fluorescence intensities of the Eu³⁺ ions. With the increasing Eu₂O₃ concentration, the amount of SnO₂ nanocrystals decreased and the Sn⁴⁺ ions formed the random glass structure together with the silica network. This structure change induced the fluorescence intensities and the hole depth to decrease.     

Preparation and Characterization of GdTaO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> Sol-Gel Luminescence Thin Films

High quality GdTaO₄:Eu³⁺ luminescence films have been successfully prepared through a modified sol-gel process. The films were prepared using inorganic materials as raw materials, and the thermal decomposition and UV assisted technique were introduced to improve the quality of the film and reduce the period for forming the thick film. Results of structural studies by atomic force microscopy (AFM) and X-ray diffraction (XRD) showed that the surface was smooth and the structure was monoclinic with the average grain size of about 55 nm. The emission and excitation spectra of the film were investigated. Related to the transition ⁵ D₀ →⁷ F₁ and ⁵ D₀→⁷ F₂ of Eu³⁺ ions, the main luminescence peaks were observed at 591 and 611 nm respectively, and the luminescence peak at 345 nm was detected simultaneously related to the TaO₄³⁻ emission. Transmission spectrum and decay curve of the luminescence are also presented in this paper.     

Photoluminescence in Er<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript>-doped silica-titania inverse opal structures

Er³⁺ photoluminescence (PL) and Yb³⁺ → Er³⁺ energy transfer (ET) phenomena in the near infrared (NIR) have been studied in three-dimensional (3-D) inverse opal (IO) structures synthesized by a colloidal/sol–gel route, starting with the deposition of polystyrene microsphere (235 nm and 460 nm diameter) direct opal templates by convective self-assembly, followed by infiltration of the interstices with Er³⁺/Yb³⁺-doped silica, titania and silica-titania sols and heat-removal of the polymeric template material. The crystalline quality of the IOs has been optimized through suitable substrate treatments, plus the control of temperature and humidity during deposition of the templates. The structural and optical properties of the 3-D opal and IO structures have been studied by field emission scanning electron microscopy and visible-NIR reflection spectroscopy, in order to assess the relationship between microstructure and the photonic properties obtained. Photonic bandgaps have been evidenced by the corresponding stop bands in the reflection spectra. The shape and the intensity of the Er^{3+ 4}I_13/2 → ⁴I_15/2 transition at ~1.5 μm were modified in most IOs relatively to similar matrix deposits without a photonic crystal structure, particularly in the case of pure silica and titania IOs, where the PL peak narrowed and intensified. It was not possible at this stage to detect Yb³⁺ → Er³⁺ ET phenomena in the IOs structures.