丁二烯在氯化稀土-乙醇-烷基铝催化体系中的某些动力学规律Ⅰ.链增长速度常数的变化规律

本文测出丁二烯在La、Nd、Sm、Gd、Dy、Ho和Y七种稀土氯化物与两种烷基铝分别组成的催化体系中聚合链增长速度常数和活性中心浓度。其30℃时k_p值在6—100 1/mol·sec间,不同稀土催化剂k_p值顺序为:k_p(Nd)～k_p(Sm)～k_p(Gd)>k_p(La)>k_p(Dy)>k_p(Ho)>k_p(Y)。钕催化剂在七种稀土催化剂中具有较大的活性中心浓度,其值为2—3×10~(-2)mol/molNd。本文对稀土络合催化剂k_p的性质作了讨论。     

STUDIES ON THE KINETICS OF PROPYLENE POLYMERIZATION WITH THE COMPLEXTYPE TiCl_3 CATALYST

The active center concentration C_p, the rate constant k_p, and the activation energy of chain propagation E_p in the polymerization of propylene with complex-type TiCl_3-(C_2H_5)_2AlCl catalyst system were studied. The Mn was corrected by (?) value determined by GPC. The values thus obtained for C_p, k_p, and E_p at 50℃were 3.01 mol/mol Ti, 6.27 1/mol·sec, and 5.10 Kcal/mol respectively.The kinetic parameters were compared with those obtained from conventional TiCl_3·AlCl_2 catalyst, showing that the higher activity of the complex-type catalyst over the conventional catalyst is not only due to the higher C_p of the former, but to a greater extent due to the increase of the k_p value.     

STUDY ON THE MECHANISM OF 1-OCTENE ZIEGLER-NATTA POLYMERIZATION BASED ON THE NUMBER OF ACTIVE CENTERS

The number of active centers (C_p)-t and k_p-t profiles of Solvay type TiCl_3 - AlR_3 (R=C_2H_5, i-C_4H_9) or Stauffer AA TiCl_3-Al (C_2H_5)_3 catalyzed 1-octene polymerization were determined by using an acetyl chloride quenching method as well as kinetic data. The results show that in the studied systems k_p decreases when C_p increases, indicating the presence of two or more types of different active centers. The C_(p~(-t)) plots of the Solvay TiCl_3-AlR_3 systems show the presence of both stable active centers and unstable centers which decay in the polymerization process. The phenomena are explained based on a model of active center plurality. The increases of C_p in the induction periods are also discussed.     

丙烯聚合络合催化剂中醚的作用

我们已初步研究了在丙烯聚合络合催化剂的制备过程中,醚络合剂在络合处理步骤中的作用,它不仅可将有害于聚合的还原副产物(AlEtCl_2)络合去掉,而且可降低TiCl~3晶型的转变温度。近年来虽有关于在TiCl_4中添加醚类物质进行热处理以改善催化剂性能的报道,但都没有解释醚在其中的特殊作用。我们在催化剂制备的第三步TiCl_4溶液中添加醚(以下用(TiCl_4/醚)溶液表示)进行热处理,发现催化剂中的醚含量有明显     

配体和溶剂对乙烯在Ti(OR)nCl4-n-AlEtCl2催化剂上低聚和高聚作用的考察

以TiCl_4(n-BuO)_4Ti,(n-BuO)_2TiCl_2为催化剂,AlEtCl_2为助催化剂,考察了Ti周围配体对乙烯聚合产物分子量的影响。结果表明,配体主要影响Ti的还原速度。在同一Ti价态下,几种配体并不显著改变链增长和链转移的速度比,而Ti的价态则是影响的主要因素。考察了溶剂效应,观察到在以氯化烷烃作溶剂时,催化剂活性与溶剂的Taft诱导常数呈线性关系。     

给电子体在制备烯烃聚合NdCl_3载体催化剂中的作用

<正> Martin以无水稀土氯化物为载体,与磷酸三丁酯(TBP)在庚烷溶剂中反应制得LnCl_3/TBP/TiCl_4载体催化剂,其中以NdCl_3为载体的催化剂对乙烯聚合有很高活性,但对TBP的作用和载钛结构涉及较少。NdCl_3为链状晶体结构,不同于层状晶体结构的MgCl_2和TiCl_3(α和δ型)。我们对NdCl_3/EtOH/TiCl_4催化剂进行了较为详细的研究,并与MgCl_2/EtOH/TiCl_4催化剂进行比较,发现NdCl_3载体催化剂与MgCl_2载体     

丙烯聚合络合催化剂形成过程的研究

以倍半物为还原剂还原TiCl_4,经异戊醚络合处理,然后在TiCl_4己烷溶液中35℃条件下热处理,制得对丙烯聚合具有高活性和高定向度的络合催化剂。研究了制备过程中各步反应产物的组成和结构特征,并讨论了TiCl_3低温晶型转变机理。     

桥联茂钛配合物催化丙烯聚合反应选择性的理论研究

采用密度泛函方法对3种不同类型的硅桥联茂钛配合物[Me_2SiN(Me_4Cp)TiCl_2(A),Me_2SiCpFluTiCl_2(B)及Me_2SiInd_2TiCl_2(C)]催化丙烯聚合反应的选择性进行了理论研究.计算结果表明,硅桥联茂金属配体的空间结构是其催化烯烃聚合反应的区域选择性和立体选择性的主要原因.聚合过程中,α-烯烃配位有1,2插入(一级插入)和2,1插入(二级插入)2种方式,3种硅桥联茂金属催化剂均表现为烯烃的一级插入,这种区域选择性与催化剂硅桥联配体的刚性结构密切相关.对烯烃聚合反应链增长机理进行了理论计算,结果表明,具有Cs对称性的Me_2SiN(Me_4Cp)TiCl_2和Me_2SiCpFluTiCl_2催化丙烯聚合分别得到无规立构和间规立构的聚烯烃产物,而具有C_2对称性的Me_2SiInd_2TiCl_2催化丙烯聚合得到等规立构的聚烯烃产物,与实验结果一致.     

含氮试剂对p-DCC/AlCl_3引发异丁烯正离子聚合的影响

以对-二枯基氯(DCC)/AlCl3体系引发异丁烯在二氯甲烷(CH2Cl2)正己烷(Hex)(40/60,V/V)混合溶剂中进行正离子聚合,探讨了DCC用量、含氮试剂2,6-二叔丁基吡啶(DtBP)和三苯胺(TPA)对异丁烯正离子聚合转化率、产物分子量及其分布的影响.结果表明,DCC和体系中微量水均可与AlCl3产生竞争络合,形成两种活性中心并引起相继的竞争引发,聚合产物的GPC谱图呈双峰分布,分子量分布宽;增加DCC用量有利于DCC与AlCl3的络合,致使链增长反应主要通过DCC与AlCl3络合形成的活性中心引发,但聚合产物分子量相对较低,分子量分布较宽;使用DtBP,可有效地抑制微量水引发及活性链向单体的转移反应,使分子量分布明显变窄,基本实现DCC的控制引发;采用DtBP与TPA共同调节聚合反应,可使聚合产物分子量分布变窄的同时,进一步提高分子量,从而得到相对较高分子量(Mw=103200)和单峰分子量分布(Mw/Mn=2.09)的聚异丁烯产物.     

在载体催化体系下二乙基锌对乙烯聚合催化效率的影响及调节分子量的动力学研究

本文对比研究了用(Ⅰ):TiCl_4/MgCl_2/Al(C_2H_5)_3和(Ⅱ):TiCl_4/MgCl_2/Al(C_2H_5)_3/Zn(C_2H_5)_2两种载体催化体系在常压下进行乙烯配位聚合的动力学行为,测定了聚合速率V_p、T_i活性中心比浓度[C~*]、聚合活化能△E、聚合速率常数K_p及链增长寿期L值。并分别测定以Al(C_2H_5)_3与Zn(C_2H_5)_2为链转移剂的链转移速度常数乓K_(tr,Al)与K_(tr,Zn)以及链转移活化能△E_(tr,Al)与△E_(tr,Zn)。表明Zn(C_2H_5)_2能有效地进一步提高催化效率和降低聚乙烯的分子量并进行讨论。     

Homolysis of weak Ti-O bonds: experimental and theoretical studies of titanium oxygen bonds derived from stable nitroxyl radicals

Titanium-oxygen bonds derived from stable nitroxyl radicals are remarkably weak and can be homolyzed at 60 degrees C. The strength of these bonds depends sensitively on the ancillary ligation at titanium. Direct measurements of the rate of Ti-O bond homolysis in Ti-TEMPO complexes Cp2TiCl(TEMPO) (3) and Cp2TiCl(4-MeO-TEMPO) (4) (TEMPO = 2,2,6,6-tetramethylpiperidine-N-oxyl, 4-MeO-TEMPO = 2,2,6,6-tetramethyl-4-methoxypiperidine-N-oxyl) were conducted by nitroxyl radical exchange experiments. Eyring plots gave the activation parameters, deltaH++ = 27(+/- 1) kcal/mol, deltaS++ = 6.9(+/- 2.3) eu for 3 and deltaH++ = 28(+/- 1) kcal/mol, deltaS++ = 9.0(+/- 3.0) eu for 4, consistent with a process involving the homolysis of a weak Ti-O bond to generate the transient Cp2Ti(III)Cl and the nitroxyl radical. Thermolysis of the titanocene TEMPO complexes in the presence of epoxides leads to the Cp2Ti(III)Cl-mediated ring-opening of the epoxide followed by trapping by the nitroxyl radical. The X-ray crystal structure of the Ti-TEMPO derivative, Cp2TiCl(4-MeO-TEMPO) (4), is reported. DFT (B3LYP/6-31G*) calculations and experimental studies reveal that the strength of the Ti-O bond decreases dramatically with the number of cyclopentadienyl groups on titanium. The calculated Ti-O bond strength of the monocyclopentadienyl complex 2 is 43 kcal/mol, whereas that of the biscyclopentadienyl complex 3 is 17 kcal/mol, a difference of 26 kcal/mol. These studies reveal that the strength of these Ti-O bonds can be tuned over an interesting and experimentally accessible temperature range by appropriate ligation on titanium.     

非MAO的茂钛均相催化体系催化苯乙烯间规聚合——[Cp~*TiMe_3]/[Ph_3C]~+[B(C_6F_5)_4]~-催化体系

非ＭＡＯ的茂钛均相催化体系催化苯乙烯间规聚合———［ＣｐＴｉＭｅ３］／［Ｐｈ３Ｃ］＋［Ｂ（Ｃ６Ｆ５）４］－催化体系许光学林尚安（中山大学高分子研究所广州５１０２７５）关键词茂钛络合物，茂金属催化剂，苯乙烯，间规聚苯乙烯间规聚苯乙烯（ｓＰＳ）由于具...     

Coordination chemistry of stable radicals: homolysis of a titanium-oxygen bond

Thermolysis of Cp2TiCl(TEMPO) (TEMPO = 2,2,6,6-tetramethylpiperidine-1-oxyl) at 60 degrees C in a benzene/CCl4 mixture generates Cp2TiCl2. Kinetic studies implicate a mechanism involving the reversible cleavage of a Ti-O bond to generate the TEMPO radical and Cp2TiCl, which is trapped by CCl4 to give Cp2TiCl2. The rate of this reaction is strongly inhibited by added TEMPO and increases with increasing CCl4 concentration, indicating that the coupling of TEMPO to Cp2TiCl is faster than chloride atom abstraction from CCl4.     

o-Phenylene-bridged Cp/sulfonamido titanium complexes for ethylene/1-octene copolymerization

The Suzuki-coupling reaction of 2-(dihydroxyboryl)-3,4-dimethyl-2-cyclopenten-1-one and 2-(dihydroxyboryl)-3-methyl-2-cyclopenten-1-one with 2-bromoaniline derivatives affords cyclopentenone compounds from which cyclopentadiene compounds, 4,6-R'(2)-2-(2,5-Me2C5H3)C6H2NH2 and 4,6-R'(2)-2-(2,3,5-Me3C5H2)C6H2NH2 are prepared. After sulfonation of the -NH2 group with p-TsCl, metallation is carried out by successive addition of Ti(NMe2)4 and Me2SiCl2 affording o-phenylene-bridged Cp/sulfonamido titanium dichloride complexes, [4,6-R'(2)-2-(2,5-Me2C5H2)C6H2NSO2C6H4CH3)]TiCl2 (R'=H, ; R'=Me, ; R'=F, ) and [4,6-R'(2)-2-(2,3,5-Me3C5H)C6H2NSO2C6H4CH3)]TiCl2 (R'=H, ; R'=Me, ; R'=F, ). The molecular structures of and [2-(2,5-Me2C5H2)C6H4NSO2C6H4CH3)]Ti(NMe2)2 are determined by X-ray crystallography. The Cp(centroid)-Ti-N angle in is smaller (100.90 degrees) than that observed for the CGC (constrained-geometry catalyst), [Me2Si(eta5-Me4Cp)(NtBu)]TiCl2 (107.6 degrees) indicating a more "constrained feature" in than in the CGC. Complex shows the highest activity among the newly prepared complexes in ethylene/1-octene copolymerization but it is slightly inferior to the CGC in terms of activity, comonomer-incorporation ability, and molecular weight of the obtained polymers.     

Revelation of the nature of the reducing species in titanocene halide-promoted reductions

The fundamental nature of Ti(III) complexes generated in tetrahydrofuran by reduction of Cp(2)TiCl(2) has been clarified by means of cyclic voltammetry and kinetic measurements. While the electrochemical reduction of Cp(2)TiCl(2) leads to the formation of Cp(2)TiCl(2)(-), the use of metals such as Zn, Al, or Mn as reductants affords Cp(2)TiCl and (Cp(2)TiCl)(2) in a mixture having a dimerization equilibrium constant of 3 x 10(3) M(-)(1), independent of the metal used. Thus, we find it unlikely that the trinuclear complexes or ionic clusters known from the solid phase should be present in solution as previously suggested. The standard potentials determined for the redox couples Cp(2)TiCl(2)/Cp(2)TiCl(2)(-), (Cp(2)TiCl)(2)(+)/(Cp(2)TiCl)(2), Cp(2)TiCl(+)/Cp(2)TiCl, and Cp(2)Ti(2+)/Cp(2)Ti(+) increase in the order listed. However, the reactivity of the different Ti(III) complexes is assessed as (Cp(2)TiCl)(2) greater, similar Cp(2)TiCl approximately Cp(2)Ti(+) > Cp(2)TiCl(2)(-) in their reactions with benzyl chloride and benzaldehyde. None of the reactions proceed by an outer-sphere electron transfer pathway, and clearly the inner-sphere character is much higher in the case of Cp(2)Ti(+) than for (Cp(2)TiCl)(2), Cp(2)TiCl, and in particular Cp(2)TiCl(2)(-). As to the electron acceptor, the inner-sphere character increases, going from benzyl chloride to benzaldehyde, and it is suggested that the chlorine atom in benzyl chloride and the oxygen atom in benzaldehyde may function as bridges between the reactants in the transition state.     

Formation of dinuclear titanium and zirconium complexes by olefin metathesis--catalytic preparation of organometallic catalyst systems

The titanium complex [(C(5)H(4)bond;allyl)TiCl(3)] (2) undergoes olefin metathesis coupling when treated with 3 mol % of [Cl(2)(L(1))(L(2))Ru=CHPh] (L(1)=L(2)=PCy(3), 4 a; L(1)=PCy(3), L(2)=(H(2)IMes), 4 b) to yield the dimetallic complex [Cl(3)Ti(C(5)H(4))-CH(2)CH=CHCH(2)-(C(5)H(4))TiCl(3)] (5). The allyl-substituted titanocene complex [Cp(C(5)H(4)bond;allyl)TiCl(2)] (3) analogously yields the dimetallic system 6 when treated with 4. The ansa-zirconocene complex [Me(2)Si(C(5)H(4))(C(5)H(3)bond;allyl)ZrCl(2)] (7) cleanly yields the analogous dimetallic coupling product 8 (>95 % isomerically pure), when treated with catalytic amounts of 4 b in toluene. Complex 8 gives an active homogeneous ethene or propene polymerization catalyst, especially at elevated temperatures, when treated with excess methylalumoxane.     

SYNTHESIS OF NOVEL THIOPHENEDIMETHYLENE BRIDGED HOMOBINUCLEAR METALLOCENES AND THEIR CATALYTIC PROPERTIES FOR ETHYLENE POLYMERIZATION

By treating disodium(thiophenedirnethylene)dicyclopentadienide C_4H_2S(CH_2C_5H_4Na)_2 with two equivalent of CpTiCl_3 or CpZrCl_3 DME at 0℃ in THF,two new thiophenedimethylene bridged binuclear metallocenes [Cl_2MC_5H_5][C_5H_4CH_2C_4H_2SCH_2C_5H_4][C_5H_5MCl_2](M=Ti 3,M=Zr 4)were synthesized in high yield and their structures were characterized by ~1H-NMR.These complexes were used as catalysts for ethylene polymerization in the presence of methylaluminoxane(MAO).The effects of polymerization temperature,time,concentration of catalyst,molar ratio of MAO/Cat on polymerization were studied in detail.The catalytic activities of thiophenedimethylene bridged binuclear metallocene catalysts(3,4)reached 2.44×10~5 g PE mol~(-1)·cat~(-1)·h~(-1),9.61×10~5 g PE mol~(-1)·cat~(-1)·h~(-1) respectively,which are higher than that of pheneyldimethylene bridged binuclear metallocene catalysts and much higher than that of corresponding mononuclear metallocenes(Cp_2TiCl_2 and Cp_2ZrCl_2).The molecular weight distribution curves of polyethylenes produced by binuclear metallocene catalysts(3,4)and by mononuclear metallocene catalyst have only single peak,but the former(MWD=3.5-4.7)is obviously broader than the latter(MWD=2.0-2.2).     

HOMO- AND COPOLYMERIZATION OF ETHYLENE CATALYZED BY ANSA-METALLOCENES WITH DOUBLY HETERO-BRIDGES

Three ansa-metallocenes(Me_2C)(Me_2Si)Cp_2TiCl_2(1),[(CH_2)_5C](Me_2Si)Cp_2TiCl_2 (2)and (Me_2C)(Me_2Si)Cp_2ZrCl_2 (3)with larger dihedral angles and longer distance from metal to the center of Cp planes were synthesized and used as catalysts for ethylene polymerization in the presence of methylaluminoxane (MAO).In the case of ethylene polymerization,compared the feature structures of unbridged metallocenes, singly bridged metallocenes and doubly bridged metallocenes 1,2,3,there exhibit the relationship ...     

Characteristics of Titanocene Catalyst Supported on Palygorskite for Ethylene Polymerization

Due to the technical problems observed for homogeneous metallocene catalysts, such as reactor fouling and requirement for large amount of expensive methylaluminoxane (MAO) as cocatalyst, the development of supported metallocene catalysts is very important…