DETERMINATION OF BRANCHING DISTRIBUTION IN HIGH cis-1,4-POLYBUTADIENE BY GPC AND AUTOMATIC VISCOMETRY

Based on the methods reported by Ambler and Kraus, a method has been developed for the determination of long-chain branching distribution in polymers by the combined use of GPC and intrinsic viscosity data of polymer fractions. In this method, g_i, λ_i, G_i, m_i, the weight percentage of polymer that is branched, etc. can be used simultaneously to characterize the distribution, degree and content of branching in polymers. Some relations between molecular weight polydispersity and branching polydispersity in Nickel-based high cis-1,4-polybutadiene samples are discussed. It was found that the number of long branches λ. per unit molecular weight is a function of molecular weight and all of the samples are highly branched at a molecular weight of about 10~6.     

Configurational characteristics of trans-1,4-polychloroprene: Experimental results on the unperturbed dimensions and their temperature coefficient

Polychloroprene [CCl?CH? CH₂? CH₂? ]_x of approximately 95% trans-1,4 stereochemical structure was prepared by low-temperature emulsion polymerization. Fractions, obtained by liquid–liquid precipitations were studied in toluene solutions at 30°C by viscometry and osmometry. In addition, force–temperature measurements were carried out on networks of the polymer in the amorphous state. The results obtained on the polymer solutions indicate that the unperturbed dimensions of trans-1,4-polychloroprene are essentially the same as those of trans-1,4-polybutadiene of the same molecular weight. This observation, that substitution of a relatively large Cl atom for one of the methine H atoms in the trans-1,4-polybutadiene repeat unit has little effect on the chain dimensions, suggests that this increase in substituent size is offset by the fact that the length of a C? Cl bond is very much greater than that of a C? H bond. The results obtained on the polymer networks indicate that the unperturbed dimensions of trans-1,4-polychloroprene decrease significantly with increasing temperature, as has also been reported for both trans-1,4-polybutadiene and trans-1,4-polyisoprene.     

Syndiotactic 1,2-polybutadiene with Co-CS2 catalyst system. I. Preparation,properties, and application of highly crystalline syndiotactic 1,2-polybutadiene

Highly crystalline syndiotactic 1,2-polybutadiene (s-PB) having melting point (mp) up to 216°C was obtained by using a Co(acac)₃-AIEt₃-CS₂ catalyst. The polymer with mp 208°C was found to have 99.7% 1,2 content and 99.6% syndiotacticity by ¹H and ¹³C-NMR measurements. The s-PB can be molded by addition of a stabilizer such as 2,6-di-t-butyl-4-hydroxymethylphenol into fiber, film, and various shaped articles. The physical properties presented in the present article include stress-strain and dynamic mechanical behavior. The highly crystalline syndiotactic 1,2-polybutadiene was applied to a carbon fiber and UBEPOL VCR (cis-1,4-polybutadiene reinforced by fibrous syndiotactic 1,2-polybutadiene).     

Alternating copolymer of butadiene and propylene. IV. Studies on the catalysts for alternating copolymerization

The catalysts for alternating copolymerization of butadiene and propylene were investigated by means of ESR technique and potentiometric titration. It was found that several kinds of active species for the production of alternating copolymer, 1,2-polybutadiene, and trans-1,4-polybutadiene are formed, depending upon the catalyst composition of VO(acac)₂? Et₃Al? Et₂AlCl. ESR and potential titration studies suggest that the active species for alternating copolymerization is a divalent vanadium compound existing in an associated form.     

Base hydrolysis of mono-alkylsubstituted chloropentaamminecobalt(III) complexes

Summary The preparation of the series ofcis- andtrans-[Co(NH₃)₄(RNH₂)Cl]²⁺ complexes (withcis, R = Me orn-Pr andtrans, R = Me, Et,n-Pr,n-Bu ori-Bu) is described. The u.v-visible spectra indicate a decrease of the ligand field on increasing chain length. Infrared spectra show an enhanced Co-Cl bond strength compared to the pentaammine. Partial molar volumes of the complex cations do not reveal steric compression. From proton exchange studies in D₂O it follows that [Co(NH₃)₅Cl]²⁺ and thecis- andtrans-[Co(NH₃)₄-(CH₃NH₂)C1]²⁺ complexes exchange the amine protons on the grouptrans to the chloro faster than those on thecis. A coordinated methylamine group exchanges its amine protons slower than a corresponding NH₃ group in the parent pentaammine, but the methyl introduction accelerates the exchange of the other NH₃ groups. The aquation of thetrans-alkylamine complexes (studied at 52° C) is acceleratedca. 10 times compared to the parent pentaammine, irrespective of the nature of the alkyl group. Thecis complexes do not show this acceleration of aquation. In base hydrolysis (studied at 25° C) thecis complexes are the most reactive (a factor 20 over the parent ion). Thecis/trans product ratio in base hydrolysis and the competition ratio in the presence of azide ions were calculated from the 500 MHz¹H n.m.r. spectra, which display distinctly different alkyl resonances for each individual complex. Thecis ions react under stereochemical retention of configuration; thetrans compounds give 10±1%trans tocis rearrangement. The ionic strength (4 mol dm^–3) and the pH do not affect this result. The same product ratio is obtained in methanol-water and DMSO-water mixtures. Ammoniation in liquid ammonia gives the same ratios as in base hydrolysis, base-catalyzed solvolysis in neat methylamine gives stereochemical retention for both thecis- andtrans-methylamine ion. The product competition ratio (Co-N₃)/(Co-OH₂) for thecis compounds and the bulkier amines (R =n- andi-Bu), 15–25% at 1 mol dm^–3N ₃ ^– , isca. twice that of thetrans compounds and the pentaammine. The results are interpreted in the classical conjugate base mechanism, and discussed in the context of current ideas about stereochemistry of base hydrolysis.Prof. C. R. Píriz Mac-Coll from Uruguay is a guest at the Free University of Amsterdam.     

cis-trans-and Intramolecular enol-enolic equilibrium of β-ketoaldehydes

Tautomerism of aromatic β-ketoaldehydes p-XPhCOCH₂CHO ( 1 , X = NMe₂, OMe, Me, H, Br, NO₂), aliphatic β-ketoaldehydes and benzoylacetaldehyde RCOCH₂CHO ( 2 , R = Me, i-Bu, t-Bu, Ph), RCOCH(Me)CHO ( 3 , R = Me, Et, i-Pr) and methyl 2-formylpropionate MeOCOCH(Me)CHO ( 4 ) has been studied by the ¹H NMR technique. In basic solvents both cis- and trans-enol forms of these compounds co-exist. trans-Enolisation, which occurs exclusively at the formyl group, is most favoured in compound ( 4 ) and least favoured in compounds ( 1 ) and ( 2 ). The increasing electron-attracting property of the substituent X in the aromatic β-ketoaldehydes ( 1 ), as well as increasing solvent basicity in the series propanediol-1, 2-carbonate, acetone < dimethylformamide < dimethylacetamide < pyridine, also shifts the equilibrium towards the trans-enol form. The trans-enol form is absent in aprotic solvents of low basicity such as CCl₄, C₂HCl₃ and toluene. The thermodynamic parameters of the cis-trans-enol (C ? T) and cis-enol-enolic (C ? C') equilibria have been estimated from the temperature dependences. The transition from the cis-to the trans-enol form is accompanied by an entropy decrease of about 10 cal mol^?1 degree^?1. Nevertheless the trans-enol form is stabilised due to its lower enthalpy. The cis-trans-enol equilibrium is determined by the relative strength of the intramolecular hydrogen bond in the cis-enol form and the intermolecular hydrogen bonds with basic solvent molecules of the trans-enol form. The enthalpy difference of the two cis-enolic forms does not exceed 1.0 kcal/mol, in rough agreement with the data calculated by the CNDO/2 approximation. Polar solvents favour the hydroxymethyleneketone form (C) for both groups of compounds 2 and 3 . The content of the hydroxymethyleneketone form is about the same within series 2 where R = Me, i-Bu, Ph and is a little higher for the t-Bu derivative. A decrease of temperature only slightly shifts the equilibrium of compounds 1 and 2 to the hydroxymethyleneketone form, while in the case of 2-methyl-β-ketoaldehydes (3) this effect is markedly pronounced.     

Improved expression of the mean-square radius of gyration, 3. 1,4-polydienes

The mean-square radii of gyration of cis- and trans-1,4-polybutadiene and corresponding 1,4-polyisoprene were derived using Abe's and Flory's rotational isomeric scheme. Calculations performed using available experimental data showed that the dependence of the mean-square radius of gyration on the molecular weight for these stereoregular polydienes can be expressed as where a and b are constants characteristic of the polymer. This behaviour is analogous to that of vinyl polymers and poly-1,1-disubstituted ethylenes discussed in the preceding papers of the present series. The mean-square radius of gyration of 1,4-polyisoprene with predominantly trans units is more sensitive to stereoirregularity than with predominantly cis units. However, 1,4-polybutadiene chains are comparatively insensitive to the stereochemical composition.     

Alternating copolymer of butadiene and propylene. III

Alternating copolymerizations of butadiene with propylene and other olefins were investigated by using VO(acac)₂–Et₃Al–Et₂AlCl system as catalyst. Butadiene–propylene copolymer with high degree of alternation was prepared with a monomer feed ratio (propylene/butadiene) of 4. Alternating copolymers of butadiene and other terminal olefins such as butene-1, pentene-1, dodecene-1, and octadiene-1,7 were also obtained. However, the butadiene–butene-2 copolymerization did not yield an alternating copolymer but a trans-1,4-polybutadiene.     

INTERACTION OF 2,4,6-TRINITROTOLUENE AND ITS ANALOGUES WITH ALDEHYDES. SYNTHESIS OF BENZOANNELATED HETEROCYCLES FROM THE PRODUCTS OF CONDENSATION

ABSTRACT

2,4,6-Trinitrotoluene (TNT) and its sulfonyl analogue 2-isobutylsulphonyl-4,6-dinitrotoluene undergo smooth condensation with chloral and fluoral to give 2-R-4,6-dinitrophenyl-1-(trihalomethyl)ethanols which easily cyclize to give 4-R-6-nitro-2-trihalomethyl-2,3-dihydrobenzo[b]furans (R=NO₂, i-Bu; halogen = F or Cl) in the presence of K₂CO₃. 2-R′-sulphonyl-4,6-dinitrotoluenes, prepared from TNT, condense with aromatic aldehydes to form 1-(2-R′-sulphonyl-4,6-dinitro)-2-arylethenes in which the ortho-nitro group, upon interaction with NaN₃ was selectively substituted by the azido group. Thermolysis of the obtained azides gave 2-aryl-4-R′-sulphonyl-6-nitroindoles (R′ = Ph, i-Bu, PhCH₂). Such N-methylated indole (R′ = i-Bu) was regioselectively aminated.     

Synthesis and characterization of polymers of 1,4-hexadienes

The homopolymerization of trans-1,4-hexadiene, cis-1,4-hexadiene, and 5-methyl-1,4-hexadiene was investigated with a variety of catalysts. During polymerization, 1,4-hexadienes undergo concurrent isomerization reactions. The nature and extent of isomerization products are influenced by the monomer structure and polymerization conditions. Nuclear magnetic resonance (NMR) and infrared (IR) data show that poly(trans-1,4-hexadiene) and poly(cis-1,4-hexadiene) prepared with a Et₃Al/α-TiCl₃/hexamethylphosphoric triamide catalyst system consist mainly of 1,2-polymerization units arranged in a regular head-to-tail sequence. A 300-MHz proton NMR spectrum shows that the trans-hexadiene polymer is isotactic; it also may be the case for the cis-hexadiene polymer. These polymers are the first examples of uncrosslinked ozone-resistant rubbers containing pendant unsaturation on alternating carbon atoms of the saturated carbon-carbon backbone. Polymerization of the 1,4-hexadienes was also studied with VOCl₃- and β-TiCl₃-based catalysts. Microstructures of the resulting polymers are quite complicated due to significant loss of unsaturation, in contrast to those obtained with the α-TiCl₃-based catalyst. In agreement with the literature, there was no discernible monomer isomerization with the VOCl₃ catalyst system.     

COPOLYMERIZATION OF BUTADIENE AND ISOPRENE CATALYZED BY V(acac)_3-Al(i-Bu)_2Cl-Al_2Et_3Cl_3 CATALYST AND CHARACTERIZATION OF THE PRODUCTS

Copolymerization of butadiene and isoprene catalyzed by the catalyst system V(acac)_3-Al(i-Bu)_2Cl-Al_2Et_3Cl_3 has been studied. Composition, microstructure, crystallinity and melting point of the copolymer obtained were determined by PGC, IR, X-ray diffraction and DSC methods respectively. The results revealed that the product was a copolymer and not a blend. The butadiene units presented in the copolymer were of trans-1,4-configuration, while the isoprene units were of both trans-1,4-and 3,4-forms. The melting point and crystallinity of the copolymer decrcascd with increase of molar ratio of isoprene to hutadiene.     

High Asymmetric Induction in Conjugate Additions of RCu · BF3 to Chiral Enoates. Preliminary communication

1,4-Additions of PhCu · BF₃, n-Bu · BF₃ and MeCu · BF₃ to the trans-8-phenyl-menthyl enoates 1 proceeded with high chiral induction. Saponification of the resulting esters 2 gave the corresponding enantiomerically pure β-substituted alkanoic acids 3 and the recovered (?)-8-phenylmenthol in good overall yields. Analogous additions to the cis-crotonate 1 led preferentially to the acids 3 enantiomeric to those obtained from the trans-crotonate 1 , although with lower selectivity. A stereochemical model is proposed consistent with the observed results (Scheme 2, Table).     

Isomerization of cis-1,4-polybutadiene by RhCl3·3H2O

The isomerization of cis-1,4-polybutadiene by RhCl₃ in aqueous emulsion was studied. The reaction was found to be slowed down by air and by base but not by quinone and was independent of the polymer solvents. Quinone did not suppress polymer gel formation. The results obtained suggest a nonradical mechanism of these reactions.     

Copolymerization of dienes with neodymium tricarboxylate-based catalysts and cis-polymerization mechanism of dienes

It was found that poly(butadiene), poly(isoprene), and poly(2,3-dimethylbutadiene) with high cis-1,4 content were obtained with Nd(OCOR)₃–(i-Bu)₃Al–Et₂AlCl catalysts (R = CF₃, CCl₃, CHCl₂, CH₂Cl, CH₃) in hexane at 50°C [cis-1,4 content: poly(BD), > 98%; poly(IP), ≥ 96%; poly(DMBD), ≥ 94%]. Copolymerization of IP and styrene (St) was carried out at various monomer feed ratios to evaluate the monomer reactivity ratio and cis-1,4 content of the diene unit and then to elucidate the cis-1,4 polymerization mechanism of IP. The cis-1,4 content of the IP unit in the copolymers decreased with increasing St content in the copolymers. The cis-1,4 polymerization was disturbed by incorporating St unit in the copolymers, since the penultimate St unit hardly coordinates to the neodymium metal, resulting in a decrease of the cis-1,4 content in the copolymers. That is, the cis-1,4 polymerization of IP is suggested to be controlled by a back-biting coordination of the penultimate diene unit. On the other hand, in the case of poly(BD-co-IP) and poly(BD-co-DMBD), the cis-1,4 content of the BD, IP, and DMBD units in the copolymers was almost constant (cis: 94–98%), irrespective of the monomer feed ratios and polymerization temperature. Consequently, the penultimate IP and DMBD units favorably control the terminal BD, IP, or DMBD unit to the cis-1,4 configuration through the back-biting coordination. For the monomer reactivity ratios, a clear difference was observed in each system: r_BD = 1.22, r_IP = 1.14; r_BD = 40.9, r_DMBD = 0.15. Low polymerizability of DMBD was mainly ascribed to the steric effect of the methyl substituents. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1707–1716, 1998     

Pseudohalogenogermylenes versus Halogenogermylenes: Difference in their Complexation Behavior towards Group 6 Metal Carbonyls

Pseudohalogenogermylenes [(iBu)₂ATI]GeY (Y=NCO 4 , NCS 5 ) show different coordination behavior towards group 6 metal carbonyls in comparison to the corresponding halogenogermylenes [(iBu)₂ATI]GeX (X=F 1 , Cl 2 , Br 3 ) (ATI=aminotroponiminate). The reactions of compounds 4 – 5 and 1 – 3 with cis‐[M(CO)₄(COD)] (M=Mo, W, COD=cyclooctadiene) gave trans‐germylene metal complexes {[(iBu)₂ATI]GeY}₂M(CO)₄ (Y=NCO, M=Mo 6 , W 11 ; Y=NCS, M=Mo 7 ) and cis‐germylene metal complexes {[(iBu)₂ATI]GeX}₂M(CO)₄ (M=Mo, X=F 8 , Cl 9 , Br 10 ; M=W, X=Cl 12 ), respectively. Theoretical studies on compounds 7 and 9 reveal that donor–acceptor interactions from Mo to Ge atoms are better stabilized in the observed trans and cis geometries than in the hypothetical cis and trans structures, respectively.     

Synthesis and absorption/emission properties of novel poly(silylenearylenevinylene)s

Polymerization of p-(dimethylsilyl)phenylacetylene in toluene at 25 and 80 °C with RhI(PPh₃)₃ catalyst afforded highly regio- and stereoregular poly(dimethylsilylene-1,4-phenylenevinylene)s [cis- and trans-poly( 1a )s] containing 98% cis- and 99% trans-vinylene moieties, respectively. The trans-type polymers exhibited redshifts and hyperchromic effects in the ultraviolet–visible spectrum as compared with the cis-type counterparts. Photoirradiation of cis- and trans-poly( 1a )s gave cis-rich mixtures at equilibrium states. The trans and cis polymers exhibited different emission properties, for example—trans polymer, emissn λ_max = 400 nm, quantum yield: 3.4 × 10⁻³ and cis polymer, emissn λ_max = 380 nm, quantum yield: 1.5 × 10⁻³. Besides poly( 1a ), poly(dimethylsilylenearylenevinylene)s containing biphenylene and phenylenesilylenephenylene units [poly( 3 )] were prepared. The extent of conjugation in these polymers decreased in the orders of biphenylene > phenylene > phenylenesilylenephenylene as well as trans-vinylene > cis-vinylene. The quantum yield of the trans-rich polymer with biphenylene moiety was fairly large and 0.15. Polyaddition of 1,4-bis(dimethylsilyl)benzene and three types of diethynylarenes (4,4′-diethynylbiphenyl, 2,7-diethynylfluorene, and 2,6-diethynylnaphthalene) catalyzed by RhI(PPh₃)₃ provided novel regio- and stereoregular polymers [poly( 6 )]. These polymers displayed blue light emission with high quantum yields (4–81%). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3615–3624, 2003     

Syndiotactic 1,2-polybutadiene with Co-CS2 catalyst system. III. 1H- and 13C-NMR study of highly syndiotactic 1,2-polybutadiene

The ¹H and ¹³C-NMR spectra of highly crystalline syndiotactic 1,2-polybutadiene (s-PB) are discussed in order to clarify the mechanism of butadiene polymerization with cobalt compound–organoaluminum–CS₂ catalysts. Cis opening of the double bonds in the syndiotactic polymerization is affirmed by the study of the copolymer from perdeuteriobutadiene and cis,cis-1,4-dideuteriobutadiene. S-PB (mp 210°C) has 99.7% 1,2 units, 0.3% isolated cis-1,4 units, and 99.6% syndiotacticity. Polymer ends (2-methyl-3-butenyl group and conjugated diene structure) are also determined. The differences in free energy of activation between 1,2 and cis-1,4 propagation and between syndiotactic and isotactic propagation are 14.0 and 9.6 kcal/mol, respectively, for Co(acac)₃-AlEt₃-AlEt₂Cl-CS₂, and 6.7 and 5.7 kcal/mol, respectively, for the aluminum-free Co(C₄H₆)(C₈H₁₃)CS₂ system. The conformation of s-PB in o-dichlorobenzene at 150°C is described by the sequence (tt)_1.6(gg)(tt).     

Synthesis and Characterization of Some Ru( tmeda ) Complexes Containing Chloride, Hydride, and Vinylidene Ligands

 The polymeric compound [Ru(cod)Cl₂] _x (cod = cyclooctadiene) reacts with 2 equivalents of tmeda (N,N,N′,N′-tetramethylethylenediamine) in refluxing MeOH to afford trans-[Ru(cod)(tmeda)(Cl)(H)] (1), which upon treatment with CHCl₃ is readily converted to the dichloro complex trans-[Ru(cod)(tmeda)Cl₂] (2). When [Ru(cod)Cl₂] _x is reacted with tmeda under an atmosphere of H₂ (3 bar), the bis-tmeda complex trans-[Ru(tmeda)₂Cl₂] (3) is obtained in 80% yield. DFT calculations revealed that 3 is by 52 kJ/mol more stable than the corresponding cis isomer. Attempts to prepare the coordinatively unsaturated complex [Ru(tmeda)₂Cl]⁺ by reacting 1 with TICF₃SO₃ were unsuccessful. According to DFT calculations, however, such a complex should be stable and, interestingly, should adopt a square pyramidal rather than a trigonal bipyramidal structure. If halide abstraction of 3 is performed in the presence of terminal alkynes HC*CR (R*t-Bu, n-Bu), the cationic vinylidene complexes [Ru(tmeda)₂(Cl)(*C*CHR)]⁺ (4a,b) are obtained.     

Quantitative estimation of trans-1,4 and cis-1,4 isomers in polychloroprene by high-resolution NMR

In the ¹H-NMR spectrum of polychloroprene dissolved in C₆D₆, the ?CH proton signal was separated into two triplet peaks. These triplet signals were assigned to the ?CH proton in the trans-1,4 and cis-1,4 isomers by measurement of ¹H-NMR spectra of 3-chloro-1-butene and a mixture of trans- and cis-2-chloro-2-butene as model compounds for the 1,2, trans-1,4 and cis-1,4 isomers. In ¹H-NMR spectra (220 Mcps) of polychloroprene dissolved in C₆D₆, two triplet signals were separated completely from which the relative concentrations of trans-1,4 and cis-1,4 isomers could be obtained quantitatively.     

Mixed Aluminum‐Magnesium‐Rare Earth Allyl Catalysts for Controlled Isoprene Polymerization: Modulation of Stereocontrol

Summary: The performances of readily available Ln(allyl)₂Cl(MgCl₂)₂ · (THF)₄ precursors (Ln = Nd, 1 ; Y, 2 ; La, 3 ), in combination with alkyl aluminum activators [MAO, AlMe₃, AlEt₃, Al(iBu)₃], have been studied in isoprene polymerization. The catalyst combination 1 /MAO (1:30) shows a high activity (average TOFs up to ca. 5 × 10⁴ mol (Ip) · mol (Nd)⁻¹ · h⁻¹ at 20 °C) and produces polyisoprene in a controlled fashion with up to 98.5% cis content, number‐average molecular weights in reasonable agreement with calculated values, and relatively narrow polydispersities index ( = 1.20–1.70). The yttrium precursor 2 affords systems with much lower activity and degree of control, but enables the formation of either 1,4‐cis‐enriched (75%) or 1,4‐trans‐enriched (91%) polyisoprenes, simply replacing the MAO activator by AlEt₃ or Al(iBu)₃, respectively.

Formation of 1,4‐cis‐ or 1,4‐trans‐enriched polyisoprenes upon activation with MAO.