Preconcentration of iron (III), cobalt (II) and copper (II) nitroso-R complexes on tetradecyldimethylbenzylammonium iodide-naphthalene adsorbent

Iron, cobalt and copper form coloured water soluble anionic complexes with disodium 1-nitroso-2-naphthol-3-6-disulphonate (nitroso R-salt). The anionic complex is retained quantitatively as a water insoluble neutral ion associated complex (M-nitroso R-TDBA) on tetradecyldimethylbenzylammonium iodide on naphthalene (TDBA(+)I(-)-naphthalene) packed column in the pH range of: Fe(III): 3.1-6.5, Co: 3.4-8.5 and Cu 5.9-8.0 when their solutions are passed individually over this adsorbent at a flow rate of 0.5-5.0 ml/min. The solid mass consisting of an ion associated metal complex along with naphthalene is dissolved out of the column with 5 ml dimethylformamide/chloroform and metals are determined spectrophotometrically. The absorbance is measured at 710 nm for iron, 425 nm for cobalt and 480 nm for copper. Beers law is obeyed in the concentration range 9.2-82 mug of iron, 425 nm for cobalt cobalt and 3.0-62 mug of copper in 5 ml of final DMF/CHCl(3) solution. The molar absorptivities are calculated to be Fe: 7.58 x 10(3), Co: 1.33 x 10(4) and Cu: 4.92 x 10(4)M(-1)cm(-1). Ten replicate determinations containing 25 mug of iron, 9.96 mug of cobalt and 3.17 mug of copper gave mean absorbances 0.677, 0.450 and 0.490 with relative standard deviations of 0.88, 0.98 and 0.92%, respectively. The interference of large number of metals and anions on the estimations of these metals has been studied. The optimized conditions so developed have been employed for the trace determination of these metals in standard alloys, waste water and fly ash samples.     

Analysis of metals by solid-liquid separation after liquid-liquid extraction spectrophotometric determination of palladium(II) by extraction of palladium dimethylglyoximate with melted naphthalene

A method of liquid-liquid extraction of palladium di-methylglyoximate with molten naphthalene followed by solid-liquid separation is successfully applied to palladium. The complex between palladium and dimethylglyoxime is easily extracted into molten naphthalene. After extraction, the very fine solidified naphthalene crystals are dissolved in chloroform, and the absorbance of the resultant solution is measured at 370 nm against a reagent blank. Beer's law is obeyed for 30-370 mug of palladium in 10 ml of chloroform, and the molar absorptivity is calculated to be 1.72 x 10(4) l.mole.(-1)mm(-1). Various alkali metal salts and metal ions do not interfere. The interference of nickel(II) is overcome by the extraction at pH 2, and that of iron(III) by masking with EDTA or by reduction to iron(II). The method is rapid and accurate.     

Extractive spectrophotometric determination of chromium(III) with phenanthrenequinone monoxime into molten naphthalene

Conditions have been developed for the determination of chromium after extraction of its phenanthrenequinone monoximate into molten naphthalene in the presence of potassium chloride. The solidified naphthalene-containing chromium complex was dissolved in chloroform and the trace amounts of chromium determined spectrophotometrically. Beer's law holds in the concentration range of 5.2–84.3 μg in 10 ml of the chloroform solution. The molar absorptivity and sensitivity (for an absorbance of 0.001) are calculated to be 6.65 × 10³ liters mol⁻¹ cm⁻¹ and 0.00782 μg/cm². Ten replicate solutions containing 31.2 μg of chromium(III) gave a mean absorbance of 0.399 with a relative standard derivation of 0.00497. Interference of various ions has been studied and the method applied for the determination of chromium(III) in certain alloys.     

Spectrophotometric determination of iron(III) dimethyldithiocarbamate (ferbam)

A spectrophotometric method was developed for the determination of ferbam (iron(III) dimethyldithiocarbamate) by converting it into an iron-phenanthroline complex, which was then absorbed on microcystalline naphthalene in the presence of tetraphenylborate, and the absorbance was measured at 515 nm against a reagent blank. The molar absorptivity of the complex was 1.2 x 10(4)l mol(-1)cm(-1). Ten replicate analyses of a sample solution containing 150 mug of ferbam gave a relative standard deviation of 0.84%. Beer's law was obeyed over the concentration range 22.4-372.9 mug of ferbam. The effects of various factors such as reagent concentration and naphthalene, shaking time and diverse ions were studied in detail. The method is sensitive and selective and can be applied to the direct determination of ferbam in commercial samples and in mixtures containing various other dithiocarbamates (e.g. ziram, zineb and maneb) in foodstuffs.     

Malachite green as a reagent for detection and spectrophotometric determination of chromium(VI)

A sensitive and inexpensive method of spectrophotometric determination of chromium(VI), based on the absorbance of its complex with malachite green and acetic acid at pH 2.5 is reported. The complex shows a molar absorptivity of 8 x 10(4) l.mole(-1) cm(-1) at 560 nm, using malachite green and acetic acid as reference solution. The effect of time, temperature, pH and reagent concentration is studied and optimum operating conditions are established. Beer's law is applicable in the concentration range 2.0-22.8 mug/ml chromium(VI). The resin beads act as a catalyst and as little as 1.6 mug of chromium(VI) is detected in the resin phase as compared to 4.1 mug in the solution phase. The standard deviation in the determinations is +/-0.40 mug/ml for a 10.35 mug/ml solution.     

Extractive spectrophotometric determination of trace amounts of iron(III) with benzyltriethylammonium chloride

The ion-association complex formed between a thiocyanato-iron(III) ion and a benzyltriethylammonium ion is extracted into 1,2-dichloroethane, and its absorbance at 476 nm is used for determination of the iron. Beer's law is obeyed up to about 4 mug/ml iron concentration in the final solution. The molar absorptivity is 2.79 x 10(4) l.mole(-1).cm(-1).     

Fluorimetric trace determination of cerium(III) with sodium triphosphate

Sodium triphosphate acts as a specific reagent for enhancing the fluorescence intensity of cerium(III). The purpose of this study was to investigate the spectrofluorimetric determination of trace amounts of Ce(III) in sodium triphosphate solution. The excitation and emission wavelengths are 303.5 nm and 353 nm respectively. Optimum sodium triphosphate concentration is found to be 0.074 g l(-1) at room temperature. The fluorescence varies linearly with the concentration of cerium(III) in the range 0.001-45 mug ml(-1). The detection limit is 9.4 x 10(-4)mug ml(-1). The relative standard deviations for 30 mug ml(-1) and 0.05 mug ml(-1) Ce(III) in 0.074 g l(-1) sodium triphosphate solution are 1.1% and 0.72% respectively. Quenching effects of other lanthanides and some inorganic anions are described. This method is a direct and rapid analytical method for the determination of Ce(III) in rare earth mixtures and cerium concentrates.     

The reaction of phenylarsenazo with chromium(III)

The conditions for the reaction between phenylarsenazo (PAA) (2-[(2-arsonophenyl)azoj-7-(phenylazo)-1, 8-dihydroxynaphthalene-3,6-disulphonic acid) and chromium(III) have been studied. A blue 1:1 complex is formed at pH 2.2 on heating the reactants at 100 degrees for 15 min. It has maximum absorption at 635 nm and is stable for at least 24 hr. The molar absorptivity is 3.3 x 10(4) 1.mole(-1).cm(-1). Beer's law is obeyed in the chromium concentration range 0-1.4 mug ml . The reaction has been successfully applied to determination of chromium in alloy steel.     

Column preconcentration of titanium in aluminium and zinc alloys with oxalic acid-ascorbic acid and the ion-pair of sodium 1,2-dihydroxybenzene-3,5-disulphonic acid and tetradecyldimethylbenzylammonium chloride supported on naphthalene using spectrometry

A solid ion-pair compound produced from sodium 1,2-dihydroxybenzene-3,5-disulphonic acid (Tiron) and tetradecyldimethylbenzylammonium chloride(TDBA) supported on naphthalene in a simple glass-tipped funnel tube provides a simple adsorbent system for preconcentrating titanium from some alloys. Titanium reacts with Tiron to form a water-soluble coloured chelate anion which in turn forms a water-insoluble stable titanium/Tiron/TDBA complex with the ion-pair on the surface of naphthalene packed in a column. Titanium is quantitatively retained on the naphthalene in the presence of L-ascorbic acid and oxalic acid in the pH range 3.0-4.5 and at a flow-rate of 1 mil/min. The metal complex and naphthalene were dissolved from the column with 5 ml of dimethylformamide(DMF), and the absorbance of the solution was measured at 398 nm. A calibration graph was linear over the range 1-18 mug of titanium in 5 ml of the final DMF solution. The complex has a molar absorptivity of 1.39 x 10(4) l.mole(-1).cm(-1) and a sensitivity of 3.44 x 10(-3) mug/cm(2) for 0.001 absorbance. Eight replicate determinations for a sample containing 12 mug of titanium gave a mean absorbance of 0.697 with a relative standard deviation of 0.82%. The interference of various ions was studied and optimum conditions were developed for the determination of titanium in various aluminium and zinc alloys.     

Spectrophotometric determination of Sb(III) in Sb(III)/Sb(V) binary mixtures using sodium dodecylsulfate/nonylphenoxy polyethoxyethanol mixed micellar media

Different micellar media had different effects on the absorption spectra of the complexes of bromopyrogallol red with Sb(III) and Sb(V). The mixed micellar medium composed of 0.7 ml of 0.2% sodium dodecylsulfate (SDS) and 0.3 ml of 2% nonylphenoxypolyethoxyethanol (OP) at 80 degrees C could be used for the sensitive determination of Sb(III) in Sb(III)/Sb(V) binary mixtures. Under the optimal conditions, Beer's Law was obeyed over the range 0.1-2.3 mug ml(-1) Sb(III) with molar absorptivity at 538 nm being 4.8 x 10(4) l mol(-1) cm(-1) and detection limit 0.04 mug ml(-1). For 10 mug Sb(III), more than 100 mug Sb(V) could be tolerated (error < 3%) in the presence of SDS/OP micellar medium as compared with 0.1 mug Sb(V) in the absence of SDS/OP micellar medium. In addition, the sensitivity of Sb(III) in the micellar medium was much higher than that in pure water medium. As compared with conventional extraction spectrometry, the proposed method produced a reproducible result. It did not need the conversion of Sb(III) to Sb(V) and a time-consuming extraction process. A detailed discussion on the selection of surfactants, the effect of temperature, and the role played by the mixed surfactants were also made.     

Spectrophotometric determination of Fe(III) in alkaline solutions without neutralization

Spectrometric study on the complexation of Fe(III) with an organic reagent obtained by coupling 3-methyl-1-phenyl-5-pyrazolone with diazotized 3-hydroxy-4-amino-benzene sulphonic acid was carried out in alkaline solutions. A 1:2 Fe(III): reagent water soluble complex is formed. The optimum pH is 9.0-11.8. The maximum absorbance of the complex lies at lambda = 560 nm, where the absorbance of the reagent is low. The molar absorptivity is 9000 l.mole(-1).cm(-1) at pH = 11.6. The value of the stability constant determined at 20 +/- 1 degrees C, pH = 11.6 and lambda = 560 nm is 4 x 10(5)M. The Beer-Lambert law is followed for iron concentration in the 0.2-5.0 mug/ml range. The spectrophotometric method was tested on synthetic solutions and thus applied for determination of traces of Fe(III) in several samples of alkaline hydroxides and carbonates without the neutralization of the solutions.     

Column chromatographic preconcentration of palladium in alloys with 9,10 phenanthrenequinonemonoxime-naphthalene

A solid chelating compound phenanthrenequinonemonoxime (PQM) supported on naphthalene provides a rapid, sensitive and economical means of preconcentration and separation of palladium from standard solutions and from synthetic samples. Palladium forms a complex with PQM supported on naphthalene in a column at pH 2.2-5.4 with a flow-rate of 1 ml/min. The metal complex and naphthalene are dissolved out from the column with 5 ml of CHCl(3) and the absorbance is measured at 430 nm or 500 nm against a reagent blank. Beers law is obeyed in the concentration range 3.0-56.0 mug and 6.0-42.0 mug at 430 nm and 500 nm respectively. The molar absorptivities are 2.10 x 10(4) and 1.69 x 10(4) 1.mole(-1).cm(-1) at 430 and 500 nm respectively.     

Simultaneous determination of hexavalent and total chromium in water and plating baths by spectrophotometry

A new spectrophotometric determination method of hexavalent chromium in waste water and plating baths is described based on the oxidation of beryllon III by chromium(VI) in 0.02M sulphuric acid medium. The decrease in the absorbance of beryllon III was measured at 482 nm with an apparent molar absorptivity of 5.15 x 10(4)1.mole(-1).cm(-1). Beer's law was obeyed for chromium(VI) over the range 0-25 mug/25 ml. After the oxidation of Cr(III) to Cr(VI) by ammonium persulphate, total chromium can be determined. Therefore, chromium(III) can be calculated by subtracting chromium(VI) from total chromium. The detection limit is 0.015 and 0.020 mug/25 ml for chromium(VI) and total chromium, respectively. A sensitive spectrophotometric method for trace Cr(III) and Cr(VI) in waste water and plating baths was developed with good precision and accuracy. The reaction is also discussed.     

Spectrophotometric determination of ascorbic acid with potassium hexacyanoferrate(III)

A new, simple and rapid method of determination of ascorbic acid in amounts of 45-360 mug is described. The ascorbic acid is determined spectrophotometrically at 420 nm from the decrease in absorbance it causes in 1 x 10(-3)M hexacyanoferrate(III) in McIlvaine buffer at pH 5.2. The proposed method is suitable for the determination of ascorbic acid in pharmaceutical preparations and probably natural products.     

Determination of trace europium based on new fluorimetric system of europium(III) with thenoyltrifluoroacetone and N,N'-dinaphthyl-N,N'-diphenyl-3,6-dioxaoctanediamide

In the present paper, N,N'-dinaphthyl-N,N'-diphenyl-3,6-dioxaoctanediamide acts as a specific reagent for enhancing the fluorescence intensity of Eu(III) complex with thenoyl trifluoroacetone (TTA), the spectrofluorimetric determination of trace amounts of Eu(III) based on the above system was carried out and its luminescence mechanism was studied. The excitation and emission wavelengths are 343.6 and 613.3 nm, respectively. The fluorescence intensities vary linearly with the concentration of europium(III) in the range 3.647x10(-3)-3.039 mug ml(-1) for the original fluorescence with a detection limit down to 2.279x10(-4) mug ml(-1) and the standard deviation is 0.063 mug ml(-1) for 10 times measurements, and in the range 7.598x10(-4)-0.0243 mug ml(-1) (SD=0.035 for 15 times measurements), 0.06078-0.6100 mug ml(-1) (SD=0.52 for 10 times measurements) for the first derivative fluorescence signal with a detection limit down to 8.566x10(-5) mug ml(-1). The interferences of other rare earths and some of inorganic ions are described. This method is a direct, rapid, selective and sensitive analytical method for the determination of trivalent europium in rare earth ore samples and high purity of rare earth oxides.     

The simple and rapid spectrophotometric determination of trace chromium(VI) after preconcentration as its colored complex on chitin

Preconcentration method with collection of metal complexes on a chitin has been applied to the spectrophotometric determination of chromium(VI) in water. The chromium(VI) is collected as its 1,5-diphenylcarbazide(DPC) complex on a column of chitin in the presence of dodecyl sulfate as counter-ion. The Cr-DPC complex retained on the chitin is eluted with a methanol-1 M acetic acid mixture (7:3, v/v), and the absorbance of the eluent is measured at 541 nm. Beer's law is obeyed over the concentration range of 0.05-0.6 mug of chromium(VI) in 1 ml of the eluent. The apparent molar absorptivity is 3.5x10(4) dm(3) mol(-1) cm(-1). The tolerance limits for Fe(III) is low, i.e. ten times that of chromium(VI), but some metal ions and common inorganic anions do not interfere in concentration range of 100-10 000 times that of chromium(VI). The present method can be applied to the determination of chromium(VI) in natural water samples.     

Simultaneous kinetic spectrophotometric determination of vanadium(V) and iron(III)

Vanadium(V) and iron(III) can be determined simultaneously at pH 2 and 25 degrees C by a single experiment using their kinetic effect on the oxidation of indigo carmine by bromate which goes through an induction period and then decreases in absorbance, at lambda(max), 612 nm. The rate of the color-fading of indigo carmine is proportional to the concentration of vanadium and is independent of the concentration of iron. The length of the induction period of the reaction is related to the concentration of iron and is independent of the concentration of vanadium. Concentrations of 0.3-2 (mug ml(-1)) vanadium(V) and 6-12 (mug ml(-1)) iron(III) were determined with mean relative errors of 2.7 and 1.6%, respectively. The interference effects of various cations and anions on determination of mixtures of vanadium and iron is reported. Application of the method to real samples and several mixtures of standard solutions are performed which gave acceptable results.     

Extractive photometric determination of gallium with 8-quinolinol in layered crystals of bismuth telluride-estimation of the determination limit

A method for determining microgram amounts of gallium in milligram samples of layered monocrystals of the type A(V)(2)B(VI)(3) is described. For the separation of 1-5 mug of gallium(III) from a large excess of bismuth in a single extraction the recommended conditions are pH 3.6-4.2 (acetate buffer, V(aq) 40 ml), an adequate excess of 8-quinolinol for complete extraction and of thiosulphate for masking bismuth. The absorbance of a chloroform extract (V(org) = 10 ml) is measured at 392.5 nm in a 50-mm cell against a blank extract concurrently obtained with a solution of pure Bi(2)Te(3). Reference polycrystalline materials are used to check the precision and accuracy of the method. In routine analysis of layered monocrystals a relative standard deviation of 4-8% is to be expected for about 1 mug of gallium in the extraction system. Estimation of the limit of determination, based on two statistical models, is discussed with respect to the error of the method and the fluctuation of the blank.     

Solvent extraction separation of iron(III) and aluminium(III) from other elements with Cyanex 302

A rapid method was developed for the solvent extraction separation of iron(III) and aluminium(III) from other elements with Cyanex 302 in chloroform as the diluent. Iron(III) was quantitatively extracted at pH 2.0-2.5 with 5 x 10(-3) M Cyanex 302 in chloroform whereas the extraction of aluminium(III) was quantitative in the pH range 3.0-4.0 with 10 x 10(-3) M Cyanex 302 in chloroform. Iron(III) was stripped from the organic phase with 1.0 M and aluminium(III) with 2.0 M hydrochloric acid. Both metals were separated from multicomponent mixtures. The method was applied to the separation of iron and aluminium from real samples.     

Simultaneous determination of gallium(III) and indium(III) by derivative spectrophotometry

A simple, selective and sensitive derivative spectrophotometric method is proposed for the simultaneous determination of gallium(III) and indium(III) in mixtures using 1-(2-pyridylazo)-2-naphthol in cationic micellar medium, without any prior separation. Beer's law is obeyed between 2.80x10(-1)-3.63 and 4.60x10(-1)-9.20 mug ml(-1) concentration of Ga(III) and In(III) at 550 and 542 nm, the isodifferential points of indium and gallium complexes in the first-order derivative mode, respectively. The proposed method is successfully applied for the determination of gallium and indium in standard reference materials and synthetic binary mixtures with a relative error of +/-2.07 and +/-2.55%, respectively.