Novel Composite of Multiwalled Carbon Nanotubes and Gold Nanoparticles Stabilized by Chitosan and Hydrophilic Ionic Liquid for Direct Electron Transfer of Glucose Oxidase

A novel composite was fabricated through dispersing multiwalled carbon nanotubes (MWNTs) in gold nanoparticle (GPs) colloid stabilized by chitosan and ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium tetrafluoroborate, BMIMBF₄). Transmission electron microscopy (TEM) experiment showed that the GPs highly dispersed on the MWNTs probably due to the electrostatic interaction among GPs, MWNTs and the imidazolium cation of BMIMBF₄. X‐ray photoelectron spectroscopy (XPS) indicated that thus‐formed gold nanostructure was mediated by BMIMBF₄. When glucose oxidase (GOD) was immobilized on the composite (MWNTs‐GPs) its ultraviolet‐visible absorption spectrum kept almost unchanged. The immobilized GOD coated glassy carbon electrode (GOD/MWNTs‐GPs/GC) exhibited a pair of well‐defined peaks in 0.10 M pH 7.0 phosphate buffer solution (PBS), with a formal potential of ?0.463 V (vs. SCE). The electrochemical process involved two‐electron transfer. The electron transfer coefficient was ca.0.56 and the electron transfer rate constant was 9.36 s^?1. Furthermore, the immobilized GOD presented good catalytic activity to the oxidation of glucose in air‐saturated PBS. The K_m and I_m values were estimated to be 13.7 μM and 0.619 μA. The GOD/MWNTs‐GPs/GC electrode displayed good stability and reproducibility.     

Preparation of the glucose sensor based on three-dimensional ordered macroporous gold film and room temperature ionic liquid

A novel type of glucose sensor was fabricated based on a glucose oxidase (GOD)-N,N-dimethtylformamide (DMF)-[BMIm][BF₄] composites modified three-dimensional ordered macroporous (3DOM) gold film electrode. The immobilized GOD exhibits a pair of well-defined reversible peaks in 50 mM pH 7.0 phosphate buffer solutions (PBS), which could be attributed to the redox of flavin adenine dinucleotide (FAD) in GOD. The research results show that ionic liquid ([BMIm][BF₄]), DMF and 3DOM gold film are crucial for GOD to exhibit a pair of stable and reversible peaks. It is believed that the large active area of 3DOM gold film can increase the amount of immobilized GOD. Simultaneously, the application of IL enhances the stability of GOD and facilitates the electron transfer between GOD and the electrode. The synergetic effect of DMF can help the GOD to maintain its bioactivity better. GOD immobilized on the electrode exhibits the favorable electrocatalytic property to glucose, and the prepared sensor has a linear range from 10 to 125 nM with a detection limit of 3.3 nM at a signal-to-noise ratio of 3σ. The apparent K _m (Michaelis- Menten constant) for the enzymatic reaction is 0.018 mM.     

An Amperometric Glucose Electrode Based on Adsorbed Glucose Oxidase on Palladium/Gold Modified Graphite

Abstract

A glucose electrode was constructed by adsorbing glucose oxidase (GOD) on a modified electrode for H₂ O ₂ oxidation, consisting of Pd/Au sputtered on graphite. Maximally, 0.8 U cm^?2 of GOD could be adsorbed. The electrode was used in a f.i.a. manifold for determination of glucose. Linear calibration curves were obtained in the concentration range 3. 10^?6 4. 10^?3 mol L^?1 glucose. The applied potentials for glucose determination were + 300 mV vs. Ag/AgCl at pH 8.0, + 350 mV at pH 7.0, + 400 mV at pH 6.0 and + 500 mV at pH 5.0. The activity vs. pH profile of adsorbed GOD was broad having an optimum between pH 5 and 6. The apparent kinetic parameters for adsorbed GOD, K_M ^app and i_max, were found to be 50 mM and 160 uA at optimal pH.     

A colloidal suspension of nanostructured poly(N-butyl benzimidazole)-graphene sheets with high oxidase yield for analytical glucose and choline detections

A colloidal suspension of nanostructured poly(N-butyl benzimidazole)-graphene sheets (PBBIns-Gs) was used to modify a gold electrode to form a three-dimensional PBBIns-Gs/Au electrode that was sensitive to hydrogen peroxide (H₂O₂) in the presence of acetic acid (AcOH). The positively charged nanostructured poly(N-butyl benzimidazole) (PBBIns) separated the graphene sheets (Gs) and kept them suspended in an aqueous solution. Additionally, graphene sheets (Gs) formed “diaphragms” that intercalated Gs, which separated PBBIns to prevent tight packing and enhanced the surface area. The PBBIns-Gs/Au electrode exhibited superior sensitivity toward H₂O₂ relative to the PBBIns-modified Au (PBBIns/Au) electrode. Furthermore, a high yield of glucose oxidase (GOD) on the PBBIns-Gs of 52.3 mg GOD per 1 mg PBBIns-Gs was obtained from the electrostatic attraction between the positively charged PBBIns-Gs and negatively charged GOD. The non-destructive immobilization of GOD on the surface of the PBBIns-Gs (GOD-PBBIns-Gs) retained 91.5% and 39.2% of bioactivity, respectively, relative to free GOD for the colloidal suspension of the GOD-PBBIns-Gs and its modified Au (GOD-PBBIns-Gs/Au) electrode. Based on advantages including a negative working potential, high sensitivity toward H₂O₂, and non-destructive immobilization, the proposed glucose biosensor based on an GOD-PBBIns-Gs/Au electrode exhibited a fast response time (5.6 s), broad detection range (10 μM to 10 mM), high sensitivity (143.5 μA mM⁻¹ cm⁻²) and selectivity, and excellent stability. Finally, a choline biosensor was developed by dipping a PBBIns-Gs/Au electrode into a choline oxidase (ChOx) solution for enzyme loading. The choline biosensor had a linear range of 0.1 μM to 0.83 mM, sensitivity of 494.9 μA mM⁻¹ cm⁻², and detection limit of 0.02 μM. The results of glucose and choline measurement indicate that the PBBIns-Gs/Au electrode provides a useful platform for the development of oxidase-based biosensors.     

Direct electrochemistry of glucose oxidase entrapped in nano gold particles-ionic liquid-N,N-dimethylformamide composite film on glassy carbon electrode and glucose sensing

The direct electrochemistry of glucose oxidase (GOD) entrapped in nano gold particles (NAs)-N,N-dimethylformamide (DMF)-1-butyl-3-methylimidazolium hexafluophosphate (BMIMPF₆) composite film on a glassy carbon electrode (NAs-DMF-GOD (BMIMPF₆)/GC) has been investigated for first time. The immobilized GOD exhibits a pair of well-defined reversible peaks in 0.050 M pH 5 phosphate solutions (PS), resulting from the redox of flavin adenine dinucleotide (FAD) in GOD. The peak currents are three times as large as those of GOD-NAs-DMF film coated GC electrode (i.e. NAs-DMF-GOD (water)/GC). In addition, the NAs-DMF-GOD (BMIMPF₆) composite material has higher thermal stability than NAs-DMF-GOD (water). Results show that ionic liquid BMIMPF₆, DMF and NAs are requisite for GOD to exhibit a pair of stable and reversible peaks. Without any of them, the peaks of GOD become small and unstable. Upon the addition of glucose, the peak currents of GOD decrease and a new cathodic peak occurs at −0.8 V (versus SCE), which corresponds to the reduction of hydrogen peroxide (H₂O₂) generated by the catalytic oxidation of glucose. The peak current of the new cathodic peak and the glucose concentration show a linear relationship in the ranges of 1.0 × 10⁻⁷ to 1.0 × 10⁻⁶ M and 2.0 × 10⁻⁶ to 2.0 × 10⁻⁵ M. The kinetic parameter I_max of H₂O₂ is estimated to be 1.19 × 10⁻⁶ A and the apparent K_m (Michaelis-Menten constant) for the enzymatic reaction is 3.49 μM. This method has been successfully applied to the determination of glucose in human plasma and beer samples, and the average recoveries are 97.2% and 99%, respectively.     

An ultrasensitive luminol cathodic electrochemiluminescence immunosensor based on glucose oxidase and nanocomposites: Graphene–carbon nanotubes and gold-platinum alloy

In the present study, a novel and ultrasensitive electrochemiluminescence (ECL) immunosensor based on luminol cathodic ECL was fabricated by using Au nanoparticles and Pt nanoparticles (nano-AuPt) electrodeposited on graphene–carbon nanotubes nanocomposite as platform for the detection of carcinoembryonic antigen (CEA). For this introduced immunosensor, graphene (GR) and single wall carbon nanotubes (CNTs) dispersed in chitosan (Chi-GR-CNTs) were firstly decorated on the bare gold electrode (GE) surface. Then nano-AuPt were electrodeposited (DpAu-Pt) on the Chi-GR-CNTs modified electrode. Subsequently, glucose oxidase (GOD) was employed to block the non-specific sites of electrode surface. When glucose was present in the working buffer solution, GOD immediately catalyzed the oxidation of glucose to in situ generate hydrogen peroxide (H₂O₂), which could subsequently promote the oxidation of luminol with an amplified cathodic ECL signal. The proposed immunosensor was performed at low potential (−0.1 to 0.4 V) and low concentration of luminol. The CEA was determined in the range of 0.1 pg mL⁻¹ to 40 ng mL⁻¹ with a limit of detection down to 0.03 pg mL⁻¹ (S N⁻¹ = 3). Moreover, with excellent sensitivity, selectivity, stability and simplicity, the as-proposed luminol-based ECL immunosensor provided great potential in clinical applications.     

Glucose oxidase/colloidal gold nanoparticles immobilized in Nafion film on glassy carbon electrode: Direct electron transfer and electrocatalysis

The direct electron transfer of glucose oxidase (GOD) was achieved based on the immobilization of GOD/colloidal gold nanoparticles on a glassy carbon electrode by a Nafion film. The immobilized GOD displayed a pair of well-defined and nearly reversible redox peaks with a formal potential (Eo ') of -0.434 V in 0.1 M pH 7.0 phosphate buffer solution and the response showed a surface-controlled electrode process. The dependence of Eo ' on solution pH indicated that the direct electron transfer reaction of GOD was a two-electron-transfer coupled with a two-proton-transfer reaction process. The experimental results also demonstrated that the immobilized GOD retained its electrocatalytic activity for the oxidation of glucose. So the resulting modified electrode can be used as a biosensor for detecting glucose.     

Unadulterated Glucose Biosensor Based on Direct Electron Transfer of Glucose Oxidase Encapsulated Chitosan Modified Glassy Carbon Electrode

Glucose oxidase (GOD) was encapsulated in chitosan matrix and immobilized on a glassy carbon electrode, achieving direct electron transfer (DET) reaction between GOD and electrode without any nano‐material. On basis of such DET, a novel glucose biosensor was fabricated for direct bioelectrochemical sensing without any electron‐mediator. GOD incorporated in chitosan films gave a pair of stable, well‐defined, and quasireversible cyclic voltammetric peaks at about ?0.284 (E_pa) and ?0.338 V (E_pc) vs. Ag/AgCl electrode in phosphate buffers. And the peak is located at the potentials characteristic of FAD redox couples of the proteins. The electrochemical parameters, such as midpoint potential (E_1/2) and apparent heterogeneous electron‐transfer rate constants (k_s) were estimated to ?0.311 V and 1.79 s^?1 by voltammetry, respectively. Experimental results indicate that the encapsulated GOD retains its catalytic activity for the oxidation of glucose. Such a GOD encapsulated chitosan based biosensor revealed a relatively rapid response time of less than 2 min, and a sufficient linear detection range for glucose concentration, from 0.60 to 2.80 mmol L^?1 with a detection limit of 0.10 mmol L^?1 and electrode sensitivity of 0.233 μA mmol^?1. The relative standard deviation (RSD) is under 3.2% (n=7) for the determination of practical serum samples. The biologic compounds probably existed in the sample, such as ascorbic acid, uric acid, dopamine, and epinephrine, do not affect the determination of glucose. The proposed method is satisfactory to the determination of human serum samples compared with the routine hexokinase method. Both the unique electrical property and biocompatibility of chitosan enable the construction of a good bio‐sensing platform for achieved DET of GOD and developed the third‐generation glucose biosensors.     

Facile Fabrication of a Graphene‐based Electrochemical Biosensor for Glucose Detection

A simple and effective glucose biosensor based on immobilization of glucose oxidase (GOD) in graphene (GR)/Nafion film was constructed. The results indicated that the immobilized GOD can maintain its native structure and bioactivity, and the GR/Nafion film provides a favorable microenvironment for GOD immobilization and promotes the direct electron transfer between the electrode substrate and the redox center of GOD. The electrode reaction of the immobilized GOD shows a reversible and surface‐controlled process with the large electron transfer rate constant (k_s) of 3.42±0.08 s^?1. Based on the oxygen consumption during the oxidation process of glucose catalyzed by the immobilized GOD, the as‐prepared GOD/GR/Nafion/GCE electrode exhibits a linear range from 0.5 to 14 mmol·L^?1 with a detection limit of 0.03 mmol·L^?1. Moreover, it displays a good reproducibility and long‐term stability.     

Study on Electrosynthesis of Nonconducting Polyaniline Used as a Permselective Membrane in Glucose Oxidase Electrode*

Nonconducting polyaniline (PANI) is electrosynthesized at the Au electrode in 0.05 mol/l aniline solution (pH 7.0) by the potential-scan methods of 0.0–0.9 V (vs. SCE) and = 0.14 V/s. This polyaniline membrane has permselectivity to H₂O₂ and can prevent uric and ascorbic acids from diffusing to electrode surface. The glucose oxidase (GOD) electrode is prepared with the nonconducting polyaniline as an exclusive membrane. The response time, linear response range, and sensitivity of the PANI–GOD electrode are 30–35 s, 0.02–22.0 mmol/l, and 2.5 nA/mmol/l, respectively. Responses for glucose at GOD and PANI–GOD electrodes are similar. But oxidation currents of uric and ascorbic acids at PANI–GOD are smaller. The response currents of these two interferences will be restrained if the PANI–GOD electrode is used to detect the glucose in human blood.     

Immobilized Fullerene C60‐Enzyme‐Based Electrochemical Glucose Sensor

A mixed‐valence cluster of cobalt(II) hexacyanoferrate and fullerene C60‐enzyme‐based electrochemical glucose sensor was developed. A water insoluble fullerene C60‐glucose oxidase (C60‐GOD) was prepared and applied as an immobilized enzyme on a glassy carbon electrode with cobalt(II) hexacyanoferrate for analysis of glucose. The glucose in 0.1 M KCl/phosphate buffer solution at pH = 6 was measured with an applied electrode potential at 0.0 mV (vs Ag/AgCl reference electrode). The C60‐GOD‐based electrochemical glucose sensor exhibited efficient electro‐catalytic activity toward the liberated hydrogen peroxide and allowed cathodic detection of glucose. The C60‐GOD electrochemical glucose sensor also showed quite good selectivity to glucose with no interference from easily oxidizable biospecies, e.g. uric acid, ascorbic acid, cysteine, tyrosine, acetaminophen and galactose. The current of H₂O₂ reduced by cobalt(II) hexacyanoferrate was found to be proportional to the concentration of glucose in aqueous solutions. The immobilized C60‐GOD enzyme‐based glucose sensor exhibited a good linear response up to 8 mM glucose with a sensitivity of 5.60 × 10² nA/mM and a quite short response time of 5 sec. The C60‐GOD‐based glucose sensor also showed a good sensitivity with a detection limit of 1.6 × 10^‐6 M and a high reproducibility with a relative standard deviation (RSD) of 4.26%. Effects of pH and temperature on the responses of the immobilized C60‐GOD/cobalt(II) hexacyanoferrate‐based electrochemical glucose sensor were also studied and discussed.     

Enhanced direct electron transfer of glucose oxidase based on a protic ionic liquid modified electrode and its biosensing application

A novel glucose oxidase (GOD) biosensor was fabricated with a protic ionic liquid (PIL) N-ethylimidazolium trifluoromethanesulfonate ([EIm][TfO]) as the modifier of a carbon electrode. Due to the excellent conductivity and the conformational changes of the microenvironment around the GOD, the electrochemical and biocatalytic properties of GOD immobilized on the PIL-based electrode were dramatically enhanced. A couple of well-defined redox peaks could be observed, with a formal potential of −0.476 V. The GOD biosensor presented good catalytic activity to the oxidation of glucose in oxygen-saturated phosphate buffer solutions. The cathodic peak currents of GOD decreased along with glucose concentrations. A linear response in the range 0.005–2.8 mM was obtained with a detection limit of 2.5 μM. The sensitivity and the apparent Michaelis–Menten constant (K _m) were estimated to be 14.96 μA mM⁻¹ and 1.53 μM, respectively. In addition, the biosensor remained stable over 30 days, indicating its good chemical and mechanical stability. The glucose content of several serum samples was determined by using the newly developed biosensor, and the results were in good agreement with those obtained by hospital measurements. All results suggested that PILs were a good media for supporting biocatalytic processes on the bioelectrode.     

Nafion coating the ferrocenylalkanethiol and encapsulated glucose oxidase electrode for amperometric glucose detection

This paper describes the fabrication and application of a complex electrode--Nafion film coating ferrocenylalkanethiol (FcC(11)SH) and encapsulated glucose oxidase (GOD) on a gold electrode. FcC(11)SH is employed as a mediator enabling the electron transfer between GOD and the electrode, GOD is encapsulated in polyacrylamide gel to improve the stability of the enzyme, and the Nafion film is coated on the modified electrode to eliminate interferents such as ascorbic acid, uric acid and acetaminophen in amperometric glucose detection. It is noticed that such a complex electrode exhibits excellent catalytic activity for glucose oxidation, and preserves the native structure of GOD and therefore its enzymatic activity. The encapsulated GOD retains more than 80% of its original biocatalytic activity even after 24 days, much longer than that of naked GOD molecules attached directly to the electrode. The oxidation peak current at the modified electrode shows a linear relationship with the glucose concentration in the range from 0.05 to 20 mM with a detection limit of 2.4 μM. In addition, the electrode displays a rapid response and good reproducibility for glucose detection, and has been successfully employed for glucose detection in blood plasma samples.     

Direct electrochemistry of glucose oxidase on sulfonated graphene/gold nanoparticle hybrid and its application to glucose biosensing

Sulfonated graphene nanosheet/gold nanoparticle (SGN/Au) hybrid was synthesized by electrostatic self-assembly of anionic SGN and positively charged gold nanoparticles. Due to the well-dispersivity of SGN in aqueous solution and its adequate negative charge, Au nanoparticles were assembled uniformly on graphene surface with high distribution. With the advantages of both graphene and Au nanoparticles, SGN/Au hybrid showed enhanced electrocatalytic activity towards O₂ reduction. Furthermore, it provided a conductive and favorable microenvironment for the glucose oxidase (GOD) immobilization and thus promoted its direct electron transfer at the glassy carbon electrode. Based on the consumption of O₂ caused by glucose at the interface of GOD electrode modified with SGN/Au hybrid, the modified electrode displayed satisfactory analytical performance, including high sensitivity (14.55 μA mM^?1 cm^?2), low detection limit (0.2 mM), an acceptable linear range from 2 to 16 mM, and also the prevention from the interference of some species. These results indicated that the prepared SGN/Au hybrid is a promising candidate material for high-performance glucose biosensor.     

A New Technique for Chemical Deposition of Pt Nanoparticles and its Applications on Biosensor Design

A new glucose biosensor design based on glucose oxidase (GOD) immobilized by polypyrrole has been described in this paper. The polymerization of pyrrole was initiated by a hexachloroplatinate which itself was reduced into Pt nanoparticles and thus served as a catalyst for the H₂O₂ oxidation. Properties of the produced GOD modified electrode were examined and the activity of the entrapped enzyme was determined by basic application on the amperometric detection of glucose. Much better results were found comparatively with the enzyme electrode for which the enzyme was entrapped by the electrochemically polymerized polypyrrole. This kind of technique for Pt nanoparticles deposition can be generalized to many cases where polypyrrole is used.     

A glucose/O2 biofuel cell base on nanographene platelet-modified electrodes

This study demonstrated a novel nanographene platelets (NGPs)-based glucose/O₂ biofuel cell (BFC) with the glucose oxidase (GOD) as the anodic biocatalysts and the laccase as the cathodic biocatalysts. The GOD/NGPs-modified electrode exhibited good catalytic activity towards glucose oxidation and the laccase/NGPs-modified electrode exhibited good catalytic activity towards O₂ electroreduction. The maximum power density was ca. 57.8 μW cm^? 2 for the assembled glucose/O₂ NGPs-based BFC. These results indicated that the NGPs were very useful for the future development of novel carbon-based nanomaterials BFC device.     

Direct Electrochemistry of Glucose Oxidase Immobilized on Titanium Carbide‐Au Nanoparticles‐Fullerene C60 Composite Film and Its Biosensing for Glucose

The direct electrochemistry of glucose oxidase (GOD) immobilized on the designed titanium carbide‐Au nanoparticles‐fullerene C₆₀ composite film modified glassy carbon electrode (TiC‐AuNPs‐C₆₀/GCE) and its biosensing for glucose were investigated. UV‐visible and Fourier‐transform infrared spectra of the resulting GOD/TiC‐AuNPs‐C₆₀ composite film suggested that the immobilized GOD retained its original structure. The direct electron transfer behaviors of immobilized GOD at the GOD/TiC‐AuNPs‐C₆₀/GCE were investigated by cyclic voltammetry in which a pair of well‐defined, quasi‐reversible redox peaks with the formal potential (E^0′) of ‐0.484 V (vs. SCE) in phosphate buffer solution (0.05 M, pH 7.0) at the scan rate of 100 mV·s^?1 were obtained. The proposed GOD modified electrode exhibited an excellent electrocatalytic activity to the reduction of glucose, and the currents of glucose reduction peak were linearly related to glucose concentration in a wider linearity range from 5.0 × 10^?6 to 1.6 × 10^?4 M with a correlation coefficient of 0.9965 and a detection limit of 2.0 × 10^?6 M (S/N = 3). The sensitivity and the apparent Michaelis‐Menten constant (K_M^app) were determined to be 149.3 μA·mM^?1·cm^?2 and 6.2 × 10^?5 M, respectively. Thus, the protocol will have potential application in studying the electron transfer of enzyme and the design of novel electrochemical biosensors.     

Cast films of lipid-coated enzymes as selective sensors for disaccharides

A stable enzyme film was prepared on a platinum electrode by casting organic solutions of a lipid-coated enzyme. The glucose oxidase (GOD)-immobilized electrode acted as a glucose sensor with a high sensitivity and a short response time. When the lipid-coated GOD was combined with a lipid-coated glycosidase on the electrode, the film showed a high selectivity for various disaccharides. For example, combining β-galactosidase with GOD, the electrode responded only to lactose (Galβ1→4Glc), having β-galactoside at the non-reducing side of the disaccharide, but not to maltose (Glcα1→4Glc) and cellobiose (Glcβ1→4Glc) in the aqueous solution. Similarly, an enzyme electrode sensitive only for maltose (Glcα1→4Glc), cellobiose (Glcβ1→4Glc), and sucrose (Glcα1→2Fru) could be prepared by using a mixed cast film of two lipid-coated enzymes, GOD and α-glucosidase, GOD and β-glucosidase, and GOD and invertase, respectively. This technique will become a new process not only for preparing sensor membranes but also for assembling water-soluble proteins on biological electrical components.     

Direct electrochemistry study of glucose oxidase on Pt nanoparticle-modified aligned carbon nanotubes electrode by the assistance of chitosan–CdS and its biosensoring for glucose

Aligned carbon nanotubes (ACNTs) electrode has been developed for the direct protein electrochemistry and enzyme-biosensor study involving two types of nanoparticles. Pt nanoparticles (Pt_nano) were electro-modified on the ACNTs’ each tube, greatly increasing the electrode surface area for locating protein and also its electronic transfer ability. Glucose oxidase (GOD) with chitosan (CS) and CdS nanoparticles electrochemically coated on each tube of ACNTs–Pt_nano by the electrodeposition reaction of CS when pH value passing its pKa. The CdS nanoparticles between ACNTs electrode and GOD have stimulated the GOD’s direct electron transfer during its redox reaction of FAD/FADH₂. The CS–GOD–CdS/ACNTs–Pt_nano electrode also offer sensitive response to the substrate of glucose with detection limit of 46.8 μM (S/N = 3) and apparent Michaelis–Menten constant of 11.86 mM.     

Glucose nanosensors based on redox polymer/glucose oxidase modified carbon fiber nanoelectrodes

This paper describes glucose nanosensors based on the co-electrodeposition of a poly(vinylimidazole) complex of [Os(bpy)₂Cl]^+/2+ and glucose oxidase (GOD) on a low-noise carbon fiber nanoelectrodes (CFNE). The SEM image shows that the osmium redox polymer/enzyme composite film is uniform. The film modified CFNE exhibits the classical features of a kinetically fast redox couple bound to the electrode surface. A strong and stable electrocatalytic current is observed in the presence of glucose. Under the optimal experimental conditions, the nanosensor offers a highly sensitive and rapid response to glucose at an operating potential of 0.22 V. A wide linear dynamic rang of 0.01-15 mM range was achieved with a detection limit of 0.004 mM. Compared with the conventional gold electrode, the nanosensor possessed higher sensitivity and longer stability. Successful attempts were made in real time monitoring rabbit blood glucose levels.