Evaluation of plastic packaging materials used in radiation sterilized medical products and food

This paper studied the results of evaluation on resistance to radiation, moisture permeability, bacteria permeability, tensile strength, elongation at break and sealing ability for several plastic films available on the market. The result shows that nylon, sarin, and polyethylene complex films, high and low density polyethylene films are applicable for packing of radiation sterilized products.     

Thermal,tensile and rheological properties of linear low density polyethylene (LLDPE) irradiated by gamma-ray in different atmospheres

The aim of this paper is to investigate structural changes of linear low density polyethylene (LLDPE) modified by ionizing radiation (gamma rays) in different atmospheres. The gamma radiation process for modification of commercial polymers is a widely applied technique to promote new physical–chemical and mechanical properties. Gamma irradiation originates free radicals which can induce chain scission or recombination, providing its annihilation, branching or crosslinking. This polymer was irradiated with gamma source of ⁶⁰Co at doses of 5, 10, 20, 50 or 100 kGy at a dose rate of 5 kGy/h. The changes in molecular structure of LLDPE, after gamma irradiations were evaluated using thermogravimetric analyzer (TGA) and tensile machine and oscillatory rheology. The results showed the variations of the properties depending on the dose at each atmosphere.     

A study of gamma-irradiated polyethylenes by temperature modulated differential scanning calorimetry

Various polyethylenes (PEs) and the effects of high-energy radiation on their structures were widely studied in the past using conventional Differential Scanning Calorimetry (DSC) measurements. In this work, we used the Temperature Modulated Differential Scanning Calorimetry (TMDSC) technique in order to obtain more information about the influence of the initial structural differences and gamma radiation on the evolution in structure and thermal properties of different polyethylenes. For this reason, low density polyethylene (LDPE), linear low density polyethylene (LLDPE) and high density polyethylene (HDPE) samples were exposed to gamma radiation, in air, to a wide range of absorbed doses (up to 2400 kGy). The separation of the total heat flow TMDSC signal into a reversing and non-reversing part enabled us to observe the low-temperature enthalpy relaxation (related to the existence of the “rigid amorphous phase”) and recrystallisation processes, as well as to follow their radiation-induced evolution and/or that of melting in a more revealing manner compared to the case of the conventional DSC. Consequently, our results indicate that TMDSC could improve the understanding of radiation-induced effects in polymers.     

Stability of high-performance liquid chromatography columns packed with poly(methyloctylsiloxane) sorbed and radiation-immobilized onto porous silica and zirconized silica

Reversed-phase packing materials were prepared from HPLC silica and from zirconized HPLC silica support particles having sorbed poly(methyloctylsiloxane) (PMOS) as the stationary phase. Portions of zirconized material were subjected to 80 kGy of ionizing radiation. Columns prepared from these packing materials were subjected to 5000 column volumes each of neutral and alkaline (pH 10) mobile phases, with periodic tests to evaluate chromatographic performance. It was shown that the PMOS stationary phase sorbed onto zirconized silica requires an immobilization treatment (such as gamma irradiation) for long term stability while prior surface zirconization of the silica support surface greatly improves the chromatographic stability of the stationary phase when using alkaline mobile phases.     

Morphology of gamma-irradiated,low-density,bulk polyethylene

Low-density bulk polyethylene was subjected to gamma radiation doses between 0.1 and 100 megarads. Surfaces produced by fracture at liquid nitrogen temperatures were studied using scanning electron microscopy. The unirradiated polyethylene and polymer irradiated to 0.1 megarad had spherical units with a diameter of about 0.15 micron lying on the fracture surface. The units lay along the edges of the lamellae and were formed by the fracture that was, therefore, not entirely brittle. Polyethylene irradiated between 1 megarad and 100 megarads exhibited spherical voids, with a diameter of about 0.1 micron in the fracture surface. The voids have been produced either by the evolution of gas in the polymer during irradiation, the most likely mechanism, or as a function of the fracture mechanism only.     

自制双层固相萃取柱在新会陈皮及其制品中11种有机磷农药测定中的应用

以自制改性多壁碳纳米管（MWNTs）和N-丙基乙二胺（PSA）填料分层填装的双层固相萃取柱为净化柱,建立了测定陈皮及其制品中11种有机磷农药残留的分析方法。样品经乙酸乙酯提取、离心后,固相萃取柱净化,净化液经Agilent RTS-1701毛细管柱分离,火焰光度检测器检测,外标法定量。考察了填料类型、填料用量、洗脱方式等因素对提取效率的影响。在优化条件下,11种有机磷农药检测的线性范围为0.020~1.0 mg/L,相关系数为0.9990~0.9998,检出限为3.5~9.6 μ g/kg。样品在10、25、100 μg/kg 3种水平下的加标回收率为50.8%~109%,相对标准偏差为2.7%~8.5%。该法准确度和灵敏度高、操作简单、快速,检出限能满足对有机磷农药残留的限量要求。自制固相萃取柱可降低成本,值得推广应用。     

Acetylcholinesterase based assay of eleven organophosphorus pesticides: finding of assay limitations

The study includes findings about limitations of acetylcholinesterase (AChE) based assay. Eleven organophosphorus pesticides: chlorpyrifos ethyl, chlorpyrifos methyl, DFP, dichlorvos, dimethoate, fenthion, paraoxon ethyl, paraoxon methyl, phosalone, pirimiphos methyl and pirimiphos ethyl were photometrically assayed using AChE as a recognition element. The study was carried out in order to find approachability of AChE based assay. In the first round, common organic solvents were tested for interfering in assay, since samples collection and extraction is a necessary part in samples processing. Isopropanol was found as the most convenient due to minimal inhibition not exceeding 5%. Though all analysed pesticides inhibit AChE in vivo, some of them are toxic after metabolisation. We found AChE based assay approachable for assay of DFP, paraoxons, and dichlorvos. These are oxoforms of organophosphorus pesticides. From thioforms of assayed pesticides, only fenthion was able significantly inhibit AChE in vitro. Electrochemical biosensor with AChE attached on platinum electrode was used for confirmation of interaction pesticide – AChE and complex stability estimation. DFP, paraoxons and dichlorvos were allowed to interact with AChE in biosensor. These pesticides were settled firmly in AChE active site as no spontaneous recovery of AChE activity was observed.     

Determination of chlorpyrifos and acephate in tropical soils and application in dissipation studies

A rapid and accurate method for the extraction and determination of the two organophosphorus insecticides, chlorpyrifos and acephate in top- and subsoil materials of three tropical clayey soils from Sarawak has been developed. Soil samples were extracted with ethyl acetate and the pesticides were determined by GC-FPD. High recoveries of 76–102% and 76–100% were obtained for acephate and chlorpyrifos respectively, at fortification levels of 0.01, 0.1 and 1 mg kg^?1 with standard deviations below 9.0%. The addition of water prior to the extraction was important for obtaining high and reproducible recoveries. The method did not require clean-up of the extracts prior to GC analysis and could be detected down to 0.01 mg kg^?1. A field study was conducted using the modified method to measure the degradation kinetics and migration of acephate and chlorpyrifos in one of the soils over a period of 84 days. The degradation of acephate and chlorpyrifos were rapid with half-lives of 3.3 and 8.7 days, respectively. Both pesticides were detected in subsoils 2 h after application at the deepest (50 cm) soil layers examined and at concentrations up to 5.42 mg kg^?1. Subsoil concentrations of acephate were higher than for chlorpyrifos, and subsoil concentrations of acephate peaked after it had started to degrade in the top soil. The subsoil concentrations of the pesticides were attributed to transport with soil particles (chlorpyrifos) and via solution (acephate) through pores and cracks present in the soil profiles. The study demonstrates the high mobility of even strongly retained and fast degrading pesticides under tropical humid conditions.     

Simultaneous determination of three organophosphorus pesticides in different food commodities by gas chromatography with mass spectrometry

A sensitive and selective gas chromatography with mass spectrometry method was developed for the simultaneous determination of three organophosphorus pesticides, namely, chlorpyrifos, malathion, and diazinon in three different food commodities (milk, apples, and drinking water) employing solid‐phase extraction for sample pretreatment. Pesticide extraction from different sample matrices was carried out on Chromabond C₁₈ cartridges using 3.0 mL of methanol and 3.0 mL of a mixture of dichloromethane/acetonitrile (1:1 v/v) as the eluting solvent. Analysis was carried out by gas chromatography coupled with mass spectrometry using selected‐ion monitoring mode. Good linear relationships were obtained in the range of 0.1–50 μg/L for chlorpyrifos, and 0.05–50 μg/L for both malathion and diazinon pesticides. Good repeatability and recoveries were obtained in the range of 78.54–86.73% for three pesticides under the optimized experimental conditions. The limit of detection ranged from 0.02 to 0.03 μg/L, and the limit of quantification ranged from 0.05 to 0.1 μg/L for all three pesticides. Finally, the developed method was successfully applied for the determination of three targeted pesticides in milk, apples, and drinking water samples each in triplicate. No pesticide was found in apple and milk samples, but chlorpyrifos was found in one drinking water sample below the quantification level.     

Analysis of selected pesticides and alkylphenols in human cord blood by gas chromatograph-mass spectrometer

A total of seven pesticides and eight alkylphenols were monitored using this method for the determination of their trace levels in human cord blood. The pesticides are lindane, diazinon, α-endosulfan, β-endosulfan, endosulfan sulfate, chlorpyrifos and endrin; while the alkylphenols are 4-n-butylphenol, 4-n-pentylphenol, 4-n-hexylphenol, 4-t-octylphenol, 4-n-heptylphenol, nonylphenol, 4-n-octylphenol and bisphenol A. The pesticides and alkylphenols in the cord blood samples were extracted with solid phase extraction IST C18 cartridges and analyzed by selected ion monitoring mode using quadrapole detector in Shimadzu QP-5000 gas chromatograph-mass spectrometer. Trace levels of pesticide and alkylphenols in the range of non-detectable to 15.17 ng ml⁻¹, were detected in the human cord blood samples. This technique of monitoring the levels of endocrine-disruptors in blood samples is consistent, reliable and cost effective while reducing wastage of time and solvents.     

Pilot scale-up and shelf stability of hydrogel wound dressings obtained by gamma radiation

This study is aimed of producing pilot batches of hydrogel wound dressings by gamma radiation and evaluating their shelf stability. Six batches of 3L capacity were prepared based on poly(vinyl pyrrolidone), agar and polyethylene glycol and they were dispensed in polyester trays, covered with polyester films and sealed in two types of materials: polyethylene bags and vacuum polyethylene bags. Dressings were formed in a single step process for the hydrogel formation and sterilization at 25–30 kGy gamma radiation dose in a JS-9500 Gamma Irradiator (Nordion, Canada). The six batches were initially physicochemical characterized in terms of dimensions and appearance, gel fraction, morphology analysis, hydrogel strength, moisture retention capability and swelling capacity. They were kept under two storage conditions: room temperature (T: 30±2 °C/RH: 70± 5%) and refrigerated temperature (T: 5±3 °C) during 24 months and sterility test was performed. The appearance of membranes was transparent, clear, uncut and flexible; the gel fraction of batches was higher than 75% and the hydrogel surface showed a porous structure. There was a slow decrease of the compression rate 20% until 7 h and about 70% at 24 h. Moisture retention capability in 5 h was similar for all the batches, about 40% and 60% at 37 °C and at room temperature respectively. The swelling of hydrogels in acidic media was strong and in alkaline media the weight variation remains almost stable until 24 h and then there is a loss of weight. The six batches remained sterile during the stability study in the conditions tested. The pilot batches were consistent from batch to batch and remained stable during 24 months.     

Leakage of gaseous 125I from a Na125I solution through a plastic film

Leakage of gaseous 125I from the various kinds of plastic film bags packing Na125I solution was determined. The polyethylene bag was permeable to the gaseous 125I and active charcoal could not prevent the leakage. The laminated plastic bags composed of polyethylene terephthalate and polyethylene was slightly permeable, and the leakage decreased either in the presence of active charcoal or with the use of doubly packed bags. Leakage of 125I from the various kinds of container for the Na125I solution was also determined.     

The effect of gamma irradiation on mechanical, and thermal properties of recycling polyethylene terephthalate and low density polyethylene (R-PET/LDPE) blend compatibilized by ethylene vinyl acetate (EVA)

A study has been made on the compatibility of recycled polyethylene terephthalate (R-PET) and low density polyethylene (LDPE) blend in the presence of ethylene vinyl acetate (EVA) as a compatibilizing agent prepared by extrusion hot stretching process. EVA content in the blend as a compatibilizing agent was an enhancement effect on radiation crosslinking of R-PET/EVA/LDPE blends and the highest radiation crosslinking was obtained when the EVA content was reached at 10 % EVA when irradiated by gamma irradiation. Blends containing different (EVA) ratios were irradiated to different doses of gamma irradiation 25, 50 and 100 kGy. The effect of the compatibilizer and radiation on mechanical, thermal properties of R-PET together with LDPE and morphology has been investigated. It was found that gamma irradiation together with the presence of compatibilizing agent (EVA) has positive effect on the mechanical and thermal properties of R-PET/LDPE blend. The structural properties of R-PET/LDPE modified by gamma irradiation and EVA as compatibilizing agent was examined by SEM. Also, it was found that the optimum concentration of EVA and gamma irradiation dose was found to be 10 % EVA and 100 kGy, respectively.     

A novel method for the determination of migration of contaminants from food contact materials

A neutron activation method has been developed for the analysis of high density polyethylene, low density polyethylene, polypropylene, polyethylene terephthalate and polystyrene food contact plastics. The method provides determination of over 50 elements at concentrations below 1 mg kg^–1. This technique has now been extended to study migration from food contact materials into standard food simulants (olive oil, acetic acid, ethanol and water). Samples of plastic are irradiated in a thermal neutron flux to produce radionuclides of the elements present in the plastic. Over a period of time the radionuclides of these elements may travel from the plastic into the food simulants, and hence the migration can be determined. Gamma ray spectrometry is performed on the simulants at the end of the test to quantify the migration. Any activity present must be due only to the migration of radionuclides of elements in the plastic and nothing else. This eliminates the need for a blank determination, which is required with existing migration methods. Preliminary studies have shown that detection limits of around 0.002 mg kg^–1 can be achieved for Sb in a retail polyethylene terephthalate (PET) bottle. This can be compared to levels of 0.005     

Spectrophotometric determination of some pesticides in water samples after preconcentration with Saccharomyces cerevisiae immobilized on sepiolite

A sensitive and selective method for the preconcentration and determination of carbaryl, chlorpyrifos, linuron, and thiram was developed. The column sorption method was used for the preconcentration studies. Several parameters, such as amount of sorbent, pH, flow rate, volume of elution solution, and interferences, that can influence the retention of pesticides on Saccharomyces cerevisiae immobilized on sepiolite were investigated. Results showed that it was possible to achieve quantitative analysis when the sample pH was in the range 4-6 for carbaryl and thiram, 4-8 for linuron and 6 for chlorpyrifos using 100 mL of sample solution containing 20 microg of pesticide and 5 mL of eluent. Recoveries of carbaryl, chlorpyrifos, linuron, and thiram were 93.2 +/- 0.4%, 97.1 -/+ 0.3%, 98.5 +/- 0.4%, and 96.1 +/- 0.2%, respectively, at 95% confidence level under optimum conditions. The capacity of the sorbent was found to be 41, 28, 35, and 46 mg g(-1) for carbaryl, chlorpyrifos, linuron, and thiram, respectively. Saccharomyces cerevisiae immobilized on sepiolite is suitable for repeated use without loss of capacity up to twenty five cycles. The pesticides studied have been determined in river water with high precision and accuracy.     

Gamma irradiation to improve plant vigour,grain development,and yield attributes of wheat

Utilizing low dose gamma radiation holds promise for physiological crop improvement. Seed treatment of low dose gamma radiation 0.01–0.10 kGy reduced plant height, improved plant vigour, flag leaf area, total and number of EBT. Gamma irradiation increased grain yield due to an increase in number of EBT and grain number while 1000 grain weight was negatively affected. Further uniformity in low dose radiation response in wheat in the field suggests that the affect is essentially at physiological than at genetic level and that role of growth hormones could be crucial.     

Effect of gamma radiation on the physico mechanical properties of recycled HDPE/modified sugarcane bagasse composite

In this work, the sugarcane bagasse (SCB) fibers were used as reinforcing filler for recycled high density polyethylene (rHDPE) to form eco-friendly composite. The SCB surface was chemically modified to improve the compatibility with rHDPE matrix. The SCB fibers were alkali modified using 10% sodium hydroxide (SCBm) and acetylated using acetic anhydride (SCBac). The chemically modified SCB fibers were characterized using Fourier transform infrared (FTIR) and scanning electronic microscopy (SEM). The composites were prepared by mixing of rHDPE with 15 phr (parts per hundred parts rHDPE) of different SCB samples. Neat rHDPE and its composites with SCB were irradiated by gamma radiation dose of 50–250 kGy. The Effect of gamma radiation on the water up-take, mechanical properties and the thermal stability of (rHDPE) and its composites was studied. The effect of gamma radiation on the compatibility between rHDPE and SCB was also investigated. The results showed that the combination between the chemical modification of fibers and the irradiation of polymer composites were more effective in compatibility improvement than chemical modification alone. The irradiated (at 100 kGy) composite containing of SCBac gave the best mechanical properties, lowest water up-take and the highest thermal stability.     

Natural radionuclides content and radon exhalation rate from Brazilian phosphogypsum piles

Phosphogypsum is a waste of the wet-acid process for producing phosphoric acid from phosphate rock. For every ton of phosphoric acid obtained, from the reaction of phosphate rock with sulphuric acid, about four tons of phosphogypsum are produced. The level of radioactivity present in the phosphogypsum, among other impurities, prevents its reuse for a variety of purposes. Large quantities of phosphogypsum have been produced worldwide. In 2006, the annual production was estimated to be about 170 million tons. Brazilian annual production of phosphogypsum reaches 5.5 million tons. Brazil, like other countries that produce phosphate fertilizer, tries to find solutions for the safe applications of phosphogypsum, in order to minimize the impact caused by its disposal. Most of the worldwide phosphogypsum is stockpiled, posing environmental concerns. The monitoring of air and groundwater pollution, radon exhalation rate and direct exposure to gamma radiation for workers should be considered. The aim of this study is to evaluate the natural radionuclides content and the radon exhalation rate from phosphogypsum piles from Ultrafertil and Fosfertil fertilizer industries. Samples of this material were analyzed by gamma ray spectrometry for their radionuclide content. Radon exhalation rate was measured by the activated charcoal collector method. A theoretical model for radon exhalation calculation, suggested by UNSCEAR, was applied in order to corroborate the experimental results.     

Evaluation of the effects of gamma radiation on thermal properties of wood species used in Brazilian artistic and cultural heritage

The wood is considered a natural composite of extreme complexity, mainly composed of cellulose, lignin, hemicellulose (polyposis), and extractives. Its composition encourages biological attacks from different species. In this context, several techniques have been studied and applied for disinfecting and decontaminating wood-made works of art and cultural heritage objects, which have been damaged by fungi, bacteria, and insects. Gamma radiation has been studied as an alternative to chemical methodologies for this purpose. By this way, the aim of this article is to illustrate the effect of gamma radiation on some physicochemical properties of Pinnus patula, Pinnus cunninghamia, Cedrella fissillis, and Ocotea porosa wood species. The irradiation has shown itself to be a fast and efficient process to eliminate infestations by both insects and microorganisms and no quarantine is required because of the no generation of toxic residues. On the other hand, this process does not protect the irradiated material from re-infestations or re-contamination. In this study, relatively high gamma radiation doses were applied up to 100 kGy so that radiation effects, which are cumulative, could be retrieved by means of thermal properties. The results have shown that gamma radiation, in the studied dose range, does not promote meaningful alterations on the evaluated properties, which allows that artifacts be irradiated multiple times, even if a re-infestation occurs.     

Degradation of alachlor herbicide by gamma radiation from cobalt-60 in aqueous and alcohol solution

Alachlor has been widely used in agriculture all over the world. It is suggested that it may be a carcinogen and an environmental estrogen. The aim of this work was to verify the degradation the alachlor by gamma radiation. Gamma radiation from ⁶⁰Co was used to degrade the alachlor herbicide in water and methanol solution. The alachlor in water and alcohol solution in the concentration of 100 mgL⁻¹ was irradiated with doses of 0.25–50 kGy, at dose rate 5–6 and 2.7 kGyh⁻¹. High performance liquid chromatography was used as an analytical technique to determine the degradation rate of herbicide studied.