Plasticized microporous poly(vinylidene fluoride) separators for lithium‐ion batteries. II. Poly(vinylidene fluoride) dense membrane swelling behavior in a liquid electrolyte—characterization of the swelling kinetics

Some microporous poly(vinylidene fluoride) (PVdF) separators for lithium‐ion batteries, used in liquid organic electrolytes based on a mixture of carbonate solvents and lithium salt LiPF₆, were characterized by the study of the swelling phenomena on dense PVdF membranes. Various aspects of the kinetics of the carbonate solvents and the solvent mixture sorption in dense PVdF slabs were studied at different temperatures. Non‐Fickian behavior, characterized by S‐shaped sorption curves, was highlighted, and a salt effect, which resulted in two‐stage sorption, was studied. Diffusion coefficients and activation energies were calculated for the Fickian portions of the sorption curves, that is, at short times and low swelling ratios. A strong influence of the different interaction parameters was shown for the swelling kinetics. This study proved that the swelling of microporous PVdF membranes could be considered instantaneous. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 544–552, 2004     

Plasticized microporous poly(vinylidene fluoride) separators for lithium‐ion batteries. I. Swelling behavior of dense membranes with respect to a liquid electrolyte—Characterization of the swelling equilibrium

Some poly(vinylidene fluoride) (PVdF) microporous separators for lithium‐ion batteries, used in liquid organic electrolytes based on a mixture of carbonate solvents and lithium salt LiPF₆, were characterized by the study of the swelling phenomena on dense PVdF membranes. We were interested in the evolution of the swelling ratios with respect to different parameters, such as the temperature, swelling solution composition, and salt concentration. To understand PVdF behavior in microporous membranes and, therefore, to have a means of predicting its behavior with different solvent mixtures, we correlated the swelling ratios in pure solvents and in solvent mixtures to the solvent–polymer interaction parameters and solvent–solvent interaction parameters. We attempted a parametric identification of swelling curves with a very simple Flory–Huggins model with relative success. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 532–543, 2004     

Synthesis of poly(vinylidene fluoride) (PVdF)/silica hybrids having interpenetrating polymer network structure by using crystallization between PVdF chains

High transparent and homogeneous poly(vinylidene fluoride) (PVdF)/silica hybrids were obtained by using an in‐situ interpenetrating polymer network (IPN) method. The simultaneous formation of PVdF gel resulting from the physical cross‐linking and silica gel from sol–gel process prevented the aggregation of PVdF in silica gel matrix. To form the physical cross‐linking between PVdF chains, the cosolvent system of dimethylformaide (DMF) and γ‐butyrolactone was used. The obtained PVdF/silica hybrids had an entangled combination of physical PVdF gel and silica gel, which was called a “complete‐ IPN” structure. The physical cross‐linking between PVdF chains in silica gel matrix was confirmed by differential scanning calorimetry (DSC) measurements. The miscibility between PVdF and silica phase was examined by scanning electron microscopy (SEM) and tapping mode atomic force microscopy (TM‐AFM) measurements. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3543–3550, 2005     

Effect of poly(vinylidene fluoride) on solvation of NaSCN in PEO

The blend-based electrolyte, polyethylene oxide (PEO)-poly(vinylidene fluoride) (PVdF)-NaSCN, was prepared and characterized by FT-IR, X-ray diffraction (XRD) and differential thermal analysis (DTA) measurements at room temperature, and the effect of PVdF content on solvation and ion association was discussed over the content of 5-95%. It is shown that PEO has much stronger ability of solvation to NaSCN than PVdF does, indicating that the polymeric donor number is more important than its dielectric constant in solvating effect of polymer. However, PVdF can keep its semicrystalline nature and form microporous structure in blend-based electrolytes. These characters make PVdF not only enhance the mechanical stability of the electrolyte thin films, but also transform PEO crystalline phase into fully amorphous phase. Although PVdF can effectively disrupt the crystalline complex P(EO)(3)NaSCN, it does not affect the component of triple aggregations. In addition, the effect of PVdF content on ion association is also discussed in PEO-NaSCN electrolytes.     

Electric field processing to control the structure of poly(vinylidene fluoride) composite proton conducting membranes

A novel method is reported for controlling the structure of poly(vinylidene fluoride) (PVdF) composite proton conducting membranes. When proton conducting Nafion or zirconium phosphate sulfophenylenphosphonate (ZrPSPP) particles are dispersed in a mixed colloidal suspension with PVdF particles, the proton conducting particles selectively respond to an applied electric field. Under appropriate conditions, the proton conducting particles are induced to assemble into chains that rapidly grow to span the gap between electrodes as the electric field is applied. By removing the solvent and melting the PVdF phase while applying the electric field, composite membranes were formed that have field-induced structure. In comparison to randomly structured composites, the electric field-processed Nafion/PVdF or ZrPSPP/PVdF composite membranes showed improved proton conductivity, water sorption, selectivity for protons over methanol, and controlled surface area changes upon swelling with water. The transport and mechanical properties of the electric field-processed composite membranes suggest the potential for improved performance in direct methanol fuel cells.     

Transcrystallization kinetics of poly(vinylidene fluoride)

We report the transcrystallinity of poly(vinylidene fluoride) on several different types of substrate materials. The supermolecular structure and its development were characterized with polarization microscopy, whereas differential scanning calorimetry was used for monitoring the isothermal and nonisothermal crystallization kinetics. Although only approximately applicable, an Avrami–Ozawa analysis of the latter yielded reliable exponents, which characterized the transcrystalline nucleation conditions, the related dimensionality of growth, and the resulting texture. The results complemented and agreed quantitatively with those of light microscopy. Several polymers, including poly(ethylene terephthalate), polytetrafluoroethylene, and polyimide, induced distinct transcrystallinity, but only a spherulitic supermolecular structure developed on glass and metallic substrates. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2130–2139, 2001     

Effect of evolved hydrogen fluoride on radiation-induced crosslinking and dehydrofluorination of poly(vinylidene fluoride)

Poly(vinylidene fluoride) (PVdF) was irradiated by ⁶⁰Co γ-rays with and without potassium hydroxide (KOH) under vacum. KOH tablets were added to absorb completely hydrogen fluoride (HF) which is the main volatile product of radiolysis of PVdF in the irradiation cell. In the presence of HF, the rates of radiation-induced crosslinking and dehydrofluorination of PVdF were lower than those in the absence of HF. The experimental results are discussed from the standpoint of stabilization of alkyl free radicals in PVdF by reaction with hydrogen fluoride.     

Effects of organophilic clay on the solvent‐maintaining capability,dimensional stability,and electrochemical properties of gel poly(vinylidene fluoride) nanocomposite electrolytes

Four quaternary alkyl ammonium salts were used in an organophilic procedure, performed on montmorillonite clay, and resulted in intercalation in dimethylformamide (DMF) or ethylene carbonate (EC)/propylene carbonate (PC) as a cosolvent between poly(vinylidene fluoride) (PVdF) and the organophilic clay. An examination using X‐ray diffraction revealed that PVdF entered galleries of montmorillonite clay, and it exhibited exfoliation and intercalation phenomena when it was analyzed with transmission electron microscopy. Gel PVdF nanocomposite electrolyte materials were successfully prepared by the addition of the appropriate percentages of DMF or PC/EC as a cosolvent, organophilic clay, and lithium perchlorate to PVdF. The maximum ionic conductivity was 1.03 × 10^?2 S/cm, and the materials exhibited better film formation, solvent‐maintaining capability, and dimensional stability than electrolyte films without added organophilic clays. The results of cyclic voltammetry testing showed that the addition of the organophilic clays significantly enhanced the electrochemical stability of the polymer electrolyte system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3873–3882, 2002     

Characterization of volume strain of poly(vinylidene fluoride) under creep test

Poly(vinylidene fluoride) (PVDF) was subjected to a creep test performed at constant true stress. The use of an original method to control and adjust, in real time, the stress allowed the assessment of volume changes occurring during the test. The adaptation of Bucknall's model enabled us to excerpt the component related to microstructural modifications from the whole volume strain. Mechanisms inducing volume strain are temperature dependent. Above ?40 °C and below 80 °C, that is, in between both glass transitions of PVDF, a linear increase of volume strain was observed as a result of polymer damage via the crazing phenomenon. In addition, this region is characterized by the presence of two distinct domains that could be attributed to either nucleation and propagation of voids or to an increase of the number of potential sites for nucleation resulting from microstructural modifications taking place during the test. On the contrary, above the secondary glass transition, a regular decrease of volume strain was observed. It was assigned to a material densification as a result of molecular orientation of the amorphous chain segments. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1754–1759, 2002     

Fine structure of poly(vinylidene fluoride) membranes prepared by phase inversion from a water/N‐methyl‐2‐pyrollidone/poly(vinylidene fluoride) system

Poly(vinylidene fluoride) (PVDF) membranes were prepared by the isothermal immersion and precipitation of PVDF/N‐methyl‐2‐pyrollidone dope solutions in either harsh or soft nonsolvent baths. Low‐voltage field emission scanning electron microscopy imaging of the formed membranes at high magnifications (e.g., 300,000×) revealed their nanoscale fine structures, particularly dendrites observed on the surfaces of the macrovoids, cellular pores, and the membrane skin, which have never been successfully presented in the literature. Evidence of crystallization was also demonstrated by X‐ray diffraction and differential scanning calorimetry measurements. The phase diagram at 25 °C, including a binodal, tie lines, and a crystallization‐induced gelation line, was determined both experimentally and theoretically. These results were further used in mass‐transfer calculations to obtain diffusion trajectories and concentration profiles for the membrane region, which were useful for elucidating the relationship between the membrane preparation conditions and the obtained membrane morphologies. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 830–842, 2004     

Poly(styrene sulfonic acid)–poly(vinylidene fluoride) interpolymer ion-exchange membranes. I. Preparation and characterization

Highly porous interpolymer ion-exchange membranes have been prepared from poly(styrene sulfonic acid), PSSA and poly(vinylidene fluoride) PVdF using a casting solvent of dimethylformamide and hexamethylphosphoramide. The membranes have been characterized by their water content, concentration potential, ionic conductivity, and their hydraulic permeability. An estimation of the porosity of the membranes has been made from the relative conductance of the potassium and the tetrabutylammonium ions in the film. This porosity has been compared with that derived from a consideration of the water flux through a Poiseuille-type pore.     

Phase transformation to β-poly(vinylidene fluoride) by milling

Cryogenic mechanical milling successfully converted α-phase poly(vinylidene fluoride) (PVDF) powder into β-phase PVDF, as measured by wide-angle X-ray diffraction. The presence of β-phase PVDF became more pronounced with increased milling times over the limited time range evaluated. This was the first recorded instance of β-phase powders forming from the α phase through milling. These β-phase powders maintained their crystal structure during compression molding at 70 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 91–97, 2004     

Intercalated poly(vinylidene fluoride)/clay nanocomposites: Structure and properties

The preparation and characterization of melt‐intercalated poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported. Organophilic clay (clay treated with dimethyl dihydrogenated tallow quaternary ammonium chloride) was used for the nanocomposite preparation. The composites were characterized with X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). XRD results indicated the intercalation of the polymer in the interlayer spacing. The incorporation of clay in PVDF resulted in the β form of PVDF. DSC nonisothermal curves showed an increase in the melting and crystallization temperatures along with a decrease in crystallinity. Isothermal crystallization studies show an enhanced rate of crystallization with the addition of clay. DMA indicated significant improvements in the storage modulus over a temperature range of ?100 to 150 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 31–38, 2003     

Electrospun cellulose acetate/poly(vinylidene fluoride) nanofibrous membrane for polymer lithium-ion batteries

The membranes for gel polymer electrolyte (GPE) for lithium-ion batteries were prepared by electrospinning a blend of poly(vinylidene fluoride) (PVdF) with cellulose acetate (CA). The performances of the prepared membranes and the resulted GPEs were investigated, including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), porosity, hydrophilicity, electrolyte uptake, mechanical property, thermal stability, AC impedance measurements, linear sweep voltammetry, and charge–discharge cycle tests. The effect of the ratio of CA to PVdF on the performance of the prepared membranes was considered. It is found that the GPE based on the blended polymer with CA:PVdF =2:8 (in weight) has an outstanding combination property-strength (11.1 MPa), electrolyte uptake (768.2 %), thermal stability (no shrinkage under 80 °C without tension), and ionic conductivity (2.61 × 10^?3 S cm^?1). The Li/GPE/LiCoO₂ battery using this GPE exhibits superior cyclic stability and storage performance at room temperature. Its specific capacity reaches up to 204.15 mAh g^?1, with embedded lithium capacity utilization rate of 74.94 %, which is higher than the other lithium-ion batteries with the same cathode material LiCoO₂ (about 50 %).     

Surface hydroxylation of poly(vinylidene fluoride) (PVDF) film

The surface of PVDF film was selectively modified by wet chemistry. Treatment with aqueous LiOH produced HF-elimination and the emergence of an oxygen-containing functionality. The XPS analysis clearly indicated the presence of ketone-, ether(epoxide)-, and alcohol motifs. The percentage of alcohols could be significantly increased by reduction of the ketones with NaBH₄ in 2-propanol, followed by reduction of the epoxides with DIBAL-H in hexane. Thus, the full treatment led to a PVDF surface displaying 7 to 16% of oxygen-containing units, of which about 60% consisted in alcohol motifs. The reactvity of the surface-displayed hydroxyl functions was assayed by radiolabeling with [³H]-Ac₂O. © 1997 John Wiley & Sons, Inc. J. Polym Sci A: Polym Chem 35: 1227–1235, 1997     

Fracture behavior of amorphous and semicrystalline blends of poly(vinylidene fluoride) and poly(methyl methacrylate)

The fracture behavior of blends of poly(vinylidene fluoride) and poly(methyl methacrylate) was investigated all over the composition range. A detailed analysis of the net stress versus crack opening displacement curves was performed. Fracture surface observations allowed statements on the process zone characteristics ahead of the crack tip. For the amorphous blends, the crack initiation energy is well related to the glass transition temperature. For the semicrystalline blends, the fracture energy is correlated with the degree of crystallinity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Ferroelectric properties of nylon 11 and poly(vinylidene fluoride) blends

Both poly(vinylidene fluoride) (PVF₂) and nylon 11 are ferroelectric polymers, and have been extensively studied over the past two decades. Blend films were made from mixed powders of these two polymers, which were then melt pressed and cold drawn. The ferroelectric properties of these blend films were investigated. The remnant polarization, P_r, was found to vary with composition, and to be 60% larger than that of either component at a 50/50 (by weight) composition where P_r exhibited a maximum of about 90 mC/m². The magnitude of the coercive field, E_c, also exhibited a maximum at this composition. Both P_r and E_c are also observed to change significantly with the draw ratio. The results are discussed based on a two-phase dielectric composite model. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 3217–3225, 1999     

Crystallization kinetics of poly(ethylene oxide) confined in semicrystalline poly(vinylidene) fluoride

Polymer blends based on poly(vinylidene fluoride) (PVDF) and poly(ethylene oxide) (PEO) have been prepared to analyze the crystallization kinetics of poly(ethylene oxide) confined in semicrystalline PVDF with different ratios of both polymers. Both blend components were dissolved in a common solvent, dimethyl formamide. Blend films were obtained by casting from the solution at 70 °C. Thus, PVDF crystals are formed by crystallization from the solution while PEO (which is in the liquid state during the whole process) is confined between PVDF crystallites. The kinetics of crystallization of the confined PEO phase was studied by isothermal and nonisothermal experiments. Fitting of Avrami model to the experimental DSC traces allows a quantitative comparison of the influence of the PVDF/PEO ratio in the blend on the crystallization behavior. The effect of melting and further recrystallization of the PVDF matrix on PEO confinement is also studied. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 588–597     

Antifouling poly(vinylidene fluoride) ultrafiltration membranes containing amphiphilic comb polymer additive

An amphiphilic comb polymer consisting of poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) [P(VDF‐co‐CTFE)] main chains and poly(oxyethylene methacrylate) (POEM) side chains was synthesized using direct initiation of the chlorine atoms in CTFE units through atom transfer radical polymerization, as confirmed by ¹H NMR and FTIR spectroscopy. The P(VDF‐co‐CTFE)‐g‐POEM comb polymer was introduced as an additive to prepare poly(vinylidene fluoride) antifouling ultrafiltration membranes. As the contents of comb polymer increased, the mechanical properties of membranes slightly decreased due to the decreased crystallinity of the membranes, as revealed by universal testing machine and X‐ray diffraction. However, water contact angle measurement and X‐ray photoelectron spectroscopy showed that the hydrophilic POEM segments spontaneously segregated on the membrane surfaces. As a result, the antifouling property of the membranes containing P(VDF‐co‐CTFE)‐g‐POEM comb polymer was considerably improved with a slight change of water flux. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 183–189, 2010     

Atom transfer radical polymerization directly from poly(vinylidene fluoride): Surface and antifouling properties

The direct preparation of grafting polymer brushes from commercial poly (vinylidene fluoride) (PVDF) films with surface‐initiated atom transfer radical polymerization (ATRP) is demonstrated. The direct initiation of the secondary fluorinated site of PVDF facilitated grafting of the hydrophilic monomers from the PVDF surface. Homopolymer brushes of 2‐(N,N‐dimethylamino)ethyl methacrylate (DMAEMA) and poly (ethylene glycol) monomethacrylate (PEGMA) were prepared by ATRP from the PVDF surface. The chemical composition and surface topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy, attenuated total reflectance/Fourier transform infrared spectroscopy, and atomic force microscopy. A kinetic study revealed a linear increase in the graft concentration of poly[2‐(N,N‐dimethylamino)ethyl methacrylate] (PDMAEMA) and poly[poly(ethylene glycol) monomethacrylate] (PPEGMA) with the reaction time, indicating that the chain growth from the surface was consistent with a controlled or living process. The living chain ends were used as macroinitiators for the synthesis of diblock copolymer brushes. The water contact angles on PVDF films were reduced by the surface grafting of DMAEMA and PEGMA. Protein adsorption experiments revealed a substantial antifouling property of PPEGMA‐grafted PVDF films and PDMAEMA‐grafted PVDF films in comparison with the pristine PVDF surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3434–3443, 2006