Synthesis of Gd2Ti2O7:Eu, V phosphors by sol-gel process and its luminescent properties

A red-emitting phosphor material, Gd₂Ti₂O₇:Eu³⁺, V⁴⁺, by added vanadium ions is synthesized using the sol-gel method. Phosphor characterization by high-resolution transmission electron microscopy shows that the phosphor possesses a good crystalline structure, while scanning electron microscopy reveals a uniform phosphor particle size in the range of 230-270 nm. X-ray photon electron spectrum analysis demonstrates that the V⁴⁺ ion promotes an electron dipole transition of Gd₂Ti₂O₇:Eu³⁺ phosphors, causing a new red-emitting phenomenon, and CIE value shifts to x=0.63, y=0.34 (a purer red region) from x=0.57, y=0.33 (CIE of Gd₂Ti₂O₇:Eu³⁺). The optimal composition of the novel red-emitting phosphor is about 26% of V⁴⁺ ions while the material is calcinated at 800  °C. The results of electroluminescent property of the material by field emission experiment by CNT-contained cathode agreed well with that of photoluminescent analysis.     

Enhanced luminescence of Ca3B2O6:Dy phosphors by Na-codoping for LED applications

The Ca_2.95−yDy_0.05B₂O₆:yNa⁺ (0≤y≤0.20) phosphors were synthesized at 1100 °C in air by the solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE), photoluminescence (PL) spectra and thermoluminescence (TL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid-state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions on 350 nm excitation was observed at 480 nm (blue) due to the ⁴F_9/2→⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2→⁶H_13/2 transitions and 660 nm (red) due to weak ⁴F_9/2→⁶H_11/2 emissions. The PL results from the investigated Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors show that Dy³⁺ emissions increase with the increase of the Na⁺ codoping ions. The integral intensity of yellow to blue (Y/B) can be tuned by controlling Na⁺ content. By the simulation of white light, the optimal CIE value (0.328, 0.334) can be achieved when the content of Na⁺-codoping ions is y=0.2. The results imply that the Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors could be potentially used as white LEDs.     

Enhanced luminescence of Dy in Y3Al5O12 by Bi co-doping

In the present paper, phosphors with the composition Y_3−x−yAl₅O₁₂:Bi³⁺_x, Dy³⁺_y were synthesized with solid state reactions. The luminescence properties of Bi³⁺ and Dy³⁺ in Y₃Al₅O₁₂(YAG) and the energy transfer from Bi³⁺ to Dy³⁺ were investigated in detail. Bi³⁺ in YAG emits one broad band peaking at 304 nm which can be ascribed to the transition from excited states ³P_{0, 1} to ground state ¹S₀. Dy³⁺ in YAG emits two groups of peaks around 484 and 583 nm, respectively, which can be ascribed to the transitions from excited state ⁴F_9/2 to ground states ⁶H_15/2 and ⁶H_13/2. The co-doping of Bi³⁺ enhances the luminescent intensity of Dy³⁺ by ∼7 times because Bi³⁺ can transfer the absorbed energy to Dy³⁺ efficiently. The mechanism of energy transfer was also discussed.     

Luminescent properties of KGd1−x(WO4)2:Eux and KGd1−x(WO4)2−y(MoO4)y:Eux phosphors in UV-VUV regions

KGd_1−x(WO₄)_2−y(MoO₄)_y:Eu³⁺_x(0.1?x?0.75, y=0 and 0.2) phosphors are synthesized through traditional solid-state reaction and their luminescent properties in ultraviolet (UV) and vacuum ultraviolet (VUV) regions are investigated. Under 147 nm excitation, these phosphors show characteristic red emission with good color purity. In order to improve their emission intensity, the MoO₄²⁻ (20 wt%) is introduced into the anion of KGd_1−x(WO₄):Eu³⁺_x. The Mo⁶⁺ and Eu³⁺ co-doped KGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped KGd(WO₄)₂ in VUV region. The chromaticity coordination of KGd_0.45(WO₄):Eu³⁺_0.55 is (x=0.669, y=0.331), while that of KGd_0.45(WO₄)_1.8(MoO₄)_0.2:Eu³⁺_0.55 is (x=0.666, y=0.334) in VUV region.     

Structure and magnetic properties of melt-spun Tb0.27Dy0.73Fex ribbons

The structure and magnetic properties of the melt-spun ribbons of Tb_0.27Dy_0.73Fe_x alloy are investigated as a function of various wheel speeds during melt-quenching using a single-roll technique. It is found that Tb_0.27Dy_0.73Fe_x alloy is difficult to be fabricated as amorphous state by using the melt-quenching method. X-ray diffractions show that all these ribbons for x=1.7−2.0 are the MgCu₂-type phase at the wheel speed of 45 m s⁻¹. For Tb_0.27Dy_0.73Fe_x alloy, the high wheel speed is beneficial to eliminate the RFe₃ phase and form the perfect MgCu₂-type phase. Compared with the bulk of Tb_0.27Dy_0.73Fe_1.95, these ribbons exhibit higher intrinsic coercivity value and their saturation magnetizations increase as well. The magnetostriction of Tb_0.27Dy_0.73Fe_1.95 composite with 4% epoxy resin is 640×10⁻⁶ at 900 kA m⁻¹.     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Luminescent properties of HTP AgGd1−xW2O8:Eux and AgGd1−x(W1−yMoy)2O8:Eux phosphor for white LED

Intense red phosphors, AgGd_1−xEu_x(W_1−yMo_y)₂O₈ (x=0.0-1.0, y=0.0-1.0), have been synthesized through traditional solid-state reaction and characterized by X-ray diffraction (XRD) and photoluminescence (PL). XRD results reveal that AgGd_1−xEu_xW₂O₈ synthesized at 1000 °C has a tetragonal crystal structure, which is named as high temperature phase (HTP) AgGdW₂O₈. All phosphors compositions with Eu³⁺ show red and green emission on excitation either in the charge-transfer or Eu³⁺ levels. Analysis of the emission spectra with different Eu³⁺ concentrations reveal that the optimum dopant concentration for Eu³⁺ is x=0.6 in the HTP AgGd_1−xEu_xW₂O₈ (x=0.0-1.0). Studies on the AgGd_0.4Eu_0.6(W_1−yMo_y)₂O₈ (y=0.0-1.0) and AgGd_1−xEu_x(W_0.7Mo_0.3)₂O₈ (x=0.0-1.0) show that the emission intensity is maximum for compositions with y=0.3 and x=0.5, respectively, and a decrease in emission intensity is observed for higher y or x values. The Mo⁶⁺ and Eu³⁺ co-doped AgGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped AgGd(WO₄)₂ in UV region. The intense emission of the tungstate/molybdate phosphors under 394 and 465 nm excitations, respectively, suggests that these materials are promising candidates as red-emitting phosphors for near-UV/blue GaN-based white LED for white light generation.     

Combustion synthesis and luminescence properties of NaY1−xEux(WO4)2 phosphors

The red phosphors NaY_1−xEu_x(WO₄)₂ with different concentrations of Eu³⁺ were synthesized via the combustion synthesis method. As a comparison, NaEu(WO₄)₂ was prepared by the solid-state reaction method. The phase composition and optical properties of as-synthesized samples were studied by X-ray powder diffraction and photoluminescence spectra. The results show that the red light emission intensity of the combustion synthesized samples under 394 nm excitation increases with increase in Eu³⁺ concentrations and calcination temperatures. Without Y ions doping, the emission spectra intensity of the NaEu(WO₄)₂ phosphor prepared by the combustion method fired at 900 °C is higher than that prepared by the solid-state reaction at 1100 °C. NaEu(WO₄)₂ phosphor synthesized by the combustion method at 1100 °C exhibits the strongest red emission under 394 nm excitation and appropriate CIE chromaticity coordinates (x=0.64, y=0.33) close to the NTSC standard value. Thus, its excellent luminescence properties make it a promising phosphor for near UV InGaN chip-based red-emitting LED application.     

Synthesis and magnetic properties of Li-Mn-Zn spinel oxides

LiMn_2−XZn_XO₄ (X<0.5) compounds were prepared by sol-gel method. The specimens with a large substitution degree (X>0.2) led to symmetry reduction from Fdm to P2₁3 in the spinel oxide, while those with a small substitution degree (X<0.1) had Fdm cubic symmetry. The Zn²⁺-substitution led to the enhancement of the low-temperature magnetic susceptibility and a shift in the Weiss constant from negative to positive, indicating that the dominant exchange interaction changed from antiferromagnetic to ferromagnetic. For the compounds with X=0.5, the spontaneous magnetization was 4.48μ_B and the Curie temperature was approximately 21 K. The experimentally obtained magnetization value was close to the value calculated under the assumption that the spins of the Mn⁴⁺ ions were aligned in ferromagnetic form. In addition, the magnetic properties of Li-Mn-Zn spinel oxides were briefly discussed, and compared with those of Li-Mn-M (M=Ni, Mg) spinel oxides.     

Growth and spectroscopic characterization of Er: Sr3Y(BO3)3 crystal

This paper reports the growth and spectroscopic characterization of Er³⁺:Sr₃Y(BO₃)₃ crystal. Er³⁺:Sr₃Y(BO₃)₃ crystal with dimensions up to ∅20×35 mm³ has been grown by Czochralski method. The polarized spectroscopic properties of Er³⁺:Sr₃Y(BO₃)₃ crystal were investigated. Based on the Judd-Ofelt theory, the effective intensity parameters Ω_t were obtained: Ω₂=1.71×10⁻²⁰ cm², Ω₄=1.39×10⁻²⁰ cm², Ω₆=0.74×10⁻²⁰ cm² for π-polarization, and Ω₂=1.77×10⁻²⁰ cm², Ω₄=1.44×10⁻²⁰ cm², Ω₆=0.65×10⁻²⁰ cm² for σ-polarization. The emission cross-section σ_em was calculated to be 4.75×10⁻²¹ cm² for π-polarization at 1536 nm and 6.30×10⁻²¹ cm² for σ-polarization at 1537 nm. The investigated results showed that Er³⁺:Sr₃Y(BO₃)₃ crystal may be regarded as a potential laser host material for 1.55 μm IR solid-state lasers.     

Photoluminescence properties of Eu in Y(PO3)3 under VUV excitation

The photoluminescence properties of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) are investigated. The excitation spectrum of Y_0.85(PO₃)₃:0.15Eu₃⁺ shows that both the (PO₃)₃³⁻ groups and the CT bands of O²⁻-Y³⁺ can efficiently absorb the excitation energy in the region of 120-250 nm. Under 147 nm excitation, the optimal emissive intensity of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) is about 36% of the commercial phosphor (Y,Gd)BO₃:Eu³⁺, which hints that the absorbed energy by the host matrix could be efficiently transferred to Eu³⁺. We try to study the concentration quenching mechanism of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) under 147 and 172 nm excitation.     

Luminescence studies of a combustion-synthesized blue–green BaAlxOy:Eu,Dy nanoparticles

Blue–green emitting BaAl_xO_y:Eu²⁺,Dy³⁺ phosphor was synthesized by the combustion method. The influence of various parameters on the structural, photoluminescence (PL) and thermoluminescence (TL) properties of the phosphor were investigated by various techniques. Phosphor nanocrystallites with high brightness were obtained without significantly changing the crystalline structure of the host. In the PL studies, broad-band excitation and emission spectra were observed with major peaks at 340 and 505 nm, respectively. The observed afterglow is ascribed to the generation of suitable traps due to the presence of the co-doped Dy³⁺ ions. Though generally broad, the peak structure of the TL glow curves obtained after irradiation with UV light was non-uniform with suggesting the contribution to afterglow from multiple events at the luminescent centers. Further insight on the afterglow behavior of the phosphor was deduced from TL decay results.     

Luminescence studies on the blue-green emitting Sr4Al14O25:Ce phosphor synthesized through solution combustion route

New blue-green emitting Sr₄Al₁₄O₂₅:Ce³⁺ phosphor is reported in this paper. The polycrystalline samples of phosphor were prepared by the conventional solution combustion method and checked for crystallization and phase by X-ray diffraction. Photoluminescence studies reveal the emission at 472 and 511 nm that correspond to the transition between lowest T_2g level of the 5d state to the ²F_5/2 and ²F_7/2 ground state levels of the Ce³⁺. The excitation at 275 nm corresponds to O²⁻→Ce⁴⁺ charge transfer processes to lowest 5d state of Ce ion (T_2g). Phosphorescence decay procedures reveal the existence of slow, medium, and fast component involved in the process. Varying the γ-dose (1-6 Gy), thermoluminescence (TL) measurements were made and glow curve maximum is obtained at 383 K. The phosphor seems to follow a first-order kinetics due to non-shifting T_m property. The T_m-T_stop method followed by the repeated initial rise method is applied to determine the distribution of activation energies and corresponding maximum positions. Chi-square minimization procedures provide the appropriate peak positions and other trapping parameters. From deconvolution results, the activation energies are found to be 0.84 and 1.06 eV, while the frequency factor is of the order of 10¹⁰ and 10¹¹ s⁻¹, respectively.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Temperature-dependence of the structural and afterglow luminance properties of polymer/SrAlxOy:Eu,Dy composites

Although aluminate phosphors have attracted great interest for applications in lamps, cathode ray tubes and plasma display panels, there still remain issues affecting operational parameters such as luminescence efficiency, stability against temperature, high color purity and perfect decay time. In addition, issues involving important aspects of the monoclinic↔hexagonal phase transition temperature still exist. In this work, SrAl_xO_y:Eu²⁺,Dy³⁺ phosphor powders were prepared by the sol–gel method. X-ray diffraction (XRD) has shown that both crystallinity and crystallite sizes increased as the temperature increased. Both SrAl₂O₄ and Sr₂Al₃O₆ phases were observed. Photoluminescence (PL) characterization shows temperature-dependence, which indicates emission at low and high annealing temperatures originating from Eu²⁺ and Eu³⁺ ions. Thermoluminescence glow and decay measurements provided useful insight on the influence of traps on luminescence behavior. Differential scanning calorimetry (DSC) and thermogravimetric studies (TGA) on composites of the phosphor in low density polyethylene (LDPE) demonstrated the varied influence of annealing temperature on some luminescence and thermal properties.     

Photoluminescence properties and effects of dopant concentration in Bi2ZnB2O7:Tb phosphor

A novel green phosphor, Tb³⁺ doped Bi₂ZnB₂O₇ was synthesized by conventional solid state reaction method. The phase of synthesized materials was determined using the XRD, DTA/TG and FTIR. The photoluminescence characteristics were investigated using spectrofluorometer at room temperature. Bi₂ZnB₂O₇:Tb³⁺ phosphors excited by 270 nm and 485 nm wavelengths. The emission spectra were composed of three bands, in which the dominated emission of green luminescence Bi₂ZnB₂O₇:Tb³⁺ attributed to the transition ⁵D₄ → ⁷F₅ is centered at 546 nm. The dependence of the emission intensity on the Tb³⁺ concentration for the Bi_2−xTb_xZnB₂O₇ (0.01 ≤ x ≤ 0.15) was studied and observed that the optimum concentration of Tb³⁺ in phosphor was 13 mol% for the highest emission intensity at 546 nm.     

Highly water resistant surface coating by fluoride on long persistent Sr4Al14O25:Eu/Dy phosphor

A novel and efficient method of providing moisture resistance of inorganic particles such as divalent europium activated strontium aluminate phosphors (Sr₄Al₁₄O₂₅:Eu²⁺/Dy³⁺) was developed by firing the phosphor in the presence of appropriate amount of ammonium fluoride at a temperature of 600-700 °C. Scanning electron microscopy, X-ray diffraction, FT-IR, EDAX and Photoluminescence measurements were carried out to characterize the uncoated and coated samples. The pH measurements were carried out for the water resistivity measurements. The phosphor particles became coated with a moisture-impervious thin coating that did not suppress the luminescence of the phosphor and can withstand complete immersion in water for long periods of time, showing very high water resistivity.     

Luminescence properties of Y2WO6:Eu incorporated with Mo or Bi ions as red phosphors for light-emitting diode applications

In this study, the red phosphors, Y₂W_1−xMo_xO₆:Eu³⁺ and Y₂WO₆:Eu³⁺,Bi³⁺, have been investigated for light-emitting diode (LED) applications. In Y₂WO₆:Eu³⁺, the excitation band edge shifts to longer wavelength with the incorporation of Mo⁶⁺ or Bi³⁺ ions. The emission spectra exhibit ⁵D₀→⁷F₁ and ⁵D₀→⁷F₂ transition of Eu³⁺ ion at 588, 593, and 610 nm, respectively. Moreover, the bluish-green luminescence of the WO₆⁶⁻ at about 460 nm is observed to decrease with the incorporation of Mo⁶⁺, which results in pure red color. Thus, this study shows that the red phosphor, Y₂WO₆:Eu³⁺, incorporated with Mo⁶⁺ or Bi³⁺ ions is advantageous for LEDs applications.     

The synthesis and the magnetic properties of Gd-doped FexCo1−x/CoyFe3−yO4 micro-octahedrons composites

Gd³⁺-substituted micro-octahedron composites (Fe_xCo_1−x/Co_yGd_zFe_3−y−zO₄) in which the Fe-Co alloy has either a bcc or fcc structure and the oxide is a spinel phase were fabricated by the hydrothermal method. The X-ray diffraction (XRD) patterns indicate that the as-synthesized Gd³⁺-substituted micro-octahedron composites are well crystallized. Scanning electron microscopy (SEM) images show that the final product consists of larger numbers of micro-octahedrons with the size ranging from 1.3 to 5 μm, and the size of products are increased with increasing the concentration of KOH. The effect of the Co²⁺/Fe²⁺ ratio (0?Co²⁺/Fe²⁺?1) and substitution Fe³⁺ ions by Gd³⁺ ions on structure, magnetic properties of the micro-octahedrons composites were investigated, and a possible growth mechanism is suggested to explain the formation of micro-octahedrons composites. The magnetic properties of the structure show the maximal saturation magnetization (107 emu/g) and the maximal coercivity (1192 Oe) detected by a vibrating sample magnetometer.