Local heat transfer coefficients around a horizontal heated tube immersed in a gas fluidized bed

The heat transfer characteristics around a single horizontal heated tube immersed in air fluidized bed was investigated, to clarify the mechanism of heat transfer in a fluidized bed heat exchanger. The local heat transfer coefficient around the tube was measured at various fluidization velocities and five different solid particles. The experimental values of the local heat transfer coefficient at the minimum fluidization velocity condition were correlated with the particle size in two empirical equations. The predicted results were in good agreement with the experiment data.     

Heat-transfer characteristics from a bundle of horizontal tubes immersed in aggregative fluidized bed

Experiments were performed to study the effect of air fluidization velocity, particle diameter, tube diameter, and pitch between tubes on heat-transfer coefficient for a bundle of horizontal tubes immersed in an aggregative fluidized bed. Not only horizontal but also vertical distributions of the heat-transfer coefficients within the bundle were also extensively determined. The heat-transfer coefficient and its maximum value were found to be dependent on the particle diameter, the air fluidization velocity, and the gap between the tubes in the bundle. The proposed correlation for the maximum heat-transfer coefficient was in good agreement with the present results.     

Fluidization behavior of graphitized glassy particles in a fluidized carbon bed cooling process for investment casting

Fluidized Carbon Bed Cooling (FCBC) is an innovative investment casting process for directional solidification of superalloy components. It takes advantage of a fluidized bed with a base of small glassy carbon beads for cooling and other low-density particles that form an insulating layer by floating to the bed surface. This so-called “Dynamic Baffle” protects the fluidized bed from the direct heat input from the high-temperature heating zone and provides the basis for an improved bed microstructure. The prerequisites for a stable casting process are stable fluidization conditions where neither collapse of the bed nor particle blow out at excessive bubble formation occur.This work aimed to investigate the fluidization behavior of spherical carbon bed material in argon and air at temperatures between 20 to 350 °C. Systematic studies at reduced pressures using the FCBC prototype device were performed to understand the stable fluidization conditions at all stages of the investment casting process. The particle shape factor and size distribution characterization and the measurement of the powder’s minimum fluidization velocity and bed voidage show that this material can be fully utilized as a cooling and buoyancy medium during the FCBC process.     

Hydrodynamics of gas-solid fluidization of a homogeneous ternary mixture in a conical bed： Prediction of bed expansion and bed fluctuation ratios

Hydrodynamic characteristics of fluidization in a conical or tapered bed differ from those in a columnar bed because the superficial velocity in the bed varies in the axial direction. Fixed and fluidized regions could coexist and sharp variations in pressure drop could occur, thereby giving rise to a noticeable pressure drop-flow rate hysteresis loop under incipient fluidization conditions. To explore these unique properties, several experiments were carried out using homogeneous, well-mixed, ternary mixtures with three dif- ferent particle sizes at varying composition in gas-solid conical fluidized beds with varying cone angles. The hydrodynamic characteristics determined include the minimum fluidization velocity, bed fluctuation, and bed expansion ratios. The dependence of these quantities on average particle diameter, mass fraction of the fines in the mixture, initial static bed height, and cone angle is discussed. Based on dimensional analysis and factorial design, correlations are developed using the system parameters, i.e. geometry of the bed （cone angle）, particle diameter, initial static bed height, density of the solid, and superficial velocity of the fluidizing medium. Experimental values of minimum fluidization velocity, bed fluctuation, and bed expansion ratios were found to agree well with the developed correlations.     

Thermal and hydraulic performance of a three-phase fluidized bed cooling tower

An experimental study was made of the thermal and hydraulic characteristics of a three-phase fluidized bed cooling tower. The experiments were carried out in a packed tower of 200 mm diameter and 2.5 m height. The packing used was spongy rubber balls 12.7 mm in diameter and with a density of 375 kg/m³. The tower characteristic was evaluated. The air-side pressure drop and the minimum fluidization velocity were measured as a function of water/air mass flux ratio (0.4–2), static bed height (300–500 mm), and hot water inlet temperature (301–334 K).

The experimental results indicate that the tower characteristics KaV/L increases with increases in the bed static height and hot water inlet temperature and with decreases in the water/air mass flux ratio. It is also shown that the air-side pressure drop increases very slowly with increases in air velocity. The minimum, fluidization velocity was found to be independent of the static bed height.

The data obtained were used to develop a correlation between the tower characteristics, hot water inlet temperature, static bed height, and the water/air mass flux ratio. The mass transfer coefficient of the three-phase fluidized bed cooling tower is much higher than that of packed-bed cooling towers with higher packing height.     

CFD-DEM investigation into flow characteristics in mixed pulsed fluidized bed under electrostatic effects

Static electricity has an important effect on gas–solid fluidized bed reactor fluidization performance. In the process of fluidization, electrostatic interaction between particles will obviously accelerate particle agglomerate formation, which consequently reduces the fluidization performance. Pulsed gas flow injection is an efficient method to enhance particle mixing, thereby weakening the occurrence of particle agglomerate. In this study, the two-dimensional hybrid pulsed fluidized bed is established. The flow characteristics are studied by using the coupled CFD-DEM numerical simulation model considering electrostatic effects. Influences of different pulsed frequencies and gas flow ratios on fluidized bed fluidization performance are investigated to obtain the optimal pulsed gas flow condition. Results show that in the presence of static electricity, the bubble generation position is lower, which is conducive to the particle flow. Pulsed gas flow can increase the particle velocity and improve the diffusion ability. The bubble generation time is different at different frequencies, and the frequency of 2.5 Hz has the most obvious effect on the flow characteristics. Different gas flow ratios have significant impacts on the particle movement amplitude. When the pulse gas flow accounts for a large ratio, the particle agglomerate tends to be larger. Therefore, in order to improve the fluidization effect, the ratio of pulsed gas flow to stable gas flow should be appropriately reduced to 0.5 or less.     

Heat Transfer and Pressure loss of a very shallow fluidized-bed heat exchanger Part 1. Experiment with a single row of tubes

A novel gas fluidized-bed heat exchanger with a very small static bed height has been developed for a heat-exchanging system using a low-pressure fan. This fluidized bed is composed of a multislit distributor, a single row of 8 mm diameter tubes, and glass beads 48–195 μm in diameter. The measured performance of heat transfer is excellent and that of fluidization is satisfactory, in spite of the static bed height being as small as 13 mm. In the best case, the test fluidized bed exhibited a heat transfer performance comparable to that of a conventional fluidized bed with a perforated plate distributor and a static bed height of 150 mm, and showed one-fourteenth the pressure loss.     

Hydrodynamics in a new liquid–solid circulating conventional fluidized bed

A new type of liquid–solid fluidized bed, named circulating conventional fluidized bed (CCFB) which operates below particle terminal velocity was proposed and experimentally studied. The hydrodynamic behavior was systematically studied in a liquid–solid CCFB of 0.032 m I.D. and 4.5 m in height with five different types of particles. Liquid–solid fluidization with external particle circulation was experimentally realized below the particle terminal velocity. The axial distribution of local solids holdup was obtained and found to be fairly uniform in a wide range of liquid velocities and solids circulation rates. The average solids holdup is found to be significantly increased compared with conventional fluidization at similar conditions. The effect of particle properties and operating conditions on bed behavior was investigated as well. Results show that particles with higher terminal velocity have higher average solids holdup.     

图像技术在非均匀布风流化床颗粒运动分析中的应用

通过实验得到了非均匀布风流化床内示踪颗粒在床层内的运动历程,以及床层内颗粒的浓度分布随时间的变化,并发纳得到颗料在非均匀布风的内旋流流化床中不同区域的扩散系数,内旋流流化床颗粒的纵向扩散系数和横向扩散系数大小相近,横向扩散系数明显大于均匀布风的鼓泡床的横向扩散系数,具有较好的横向扩散特性,有利于使流化床内横向不均匀的状况得到改善。     

Numerical simulations of high pressure carbon dioxide fluid fluidized beds

Hydrodynamics of carbon dioxide fluid-particle mixtures are predicted using a low density ratio-based kinetic theory of granular flow in high pressure carbon dioxide fluid fluidized beds. A coexistence of particle waves and particle aggregates exists along bed height. The threshold to identify the occurrence of particle aggregates is suggested based on standard deviation of solid volume fractions in aggregative fluidization. The existence time fractions and frequencies of particle aggregates are predicted along axial direction. The effect of carbon dioxide fluid temperature and pressure on volume fraction and velocity distributions are analyzed at different inlet carbon dioxide velocities and particle densities in high pressure carbon dioxide fluidized beds. Simulated results indicate that the carbon dioxide-particles fluidization transits from particulate to aggregative states with the increase of inlet carbon dioxide velocities. The computed fluid volume fractions and heterogeneity indexes are close to the measurements in a high pressure carbon dioxide fluidized bed.     

Bottom bed regimes in a circulating fluidized bed boiler

This paper extends previous work on the fluidization regimes of the bottom bed of circulating flyidized bed (CFB) boilers. Pressure measurements were performed to obtain the time-average bottom bed voidage and to study the bed pressure fluctuations. The measurements were carried out in a 12 MW_th CFB boiler operated at 850°C and also under ambient conditions (40°C). Two bubbling regimes were identified: a “single bubble regime” with large single bubbles present at low fluidization velocities, and, at high fluidization velocities, an “exploding bubble regime” with bubbles often stretching all the way from the air distributor to the surface of the bottom bed. The exploding bubble regime results in a high through-flow of gas, indirectly seen from the low average voidage of the bottom bed, which is similar to that of a stationary fluidized bed boiler, despite the higher gas velocities in the CFB boiler. Methods to determine the fluidization velocity at the transition from the single to the exploding bubble regime are proposed and discussed. The transition velocity increases with an increase in particle size and bed height.     

Removal of dust from flue gas in magnetically stabilized fluidized bed

A magnetically stabilized fluidized bed (MSFB, φ 500mm x 2100mm) was designed to study dust removal from flue gas. Based on the mechanism of dust removal in a fixed bed, the effects on collection efficiency of magnetic field intensity, ratio of flue gas velocity to minimum fluidization velocity, bed height, and particle average diameter, were investigated. Then feasible methods for MSFB to better remove dust were proposed. Over 95% of dust removal with MSFB can be achieved, when stable fluidization is maintained and when magnetic particles are frequently renewed.     

Heat transfer and hydrodynamic studies on two- and three-phase fluidized beds of floating bubble breakers

Heat transfer characteristics in three-phase fluidized beds of floating bubble breakers have been studied in a 0.142 m I.D. x 2.0 m high Plexiglas column fitted with an axially mounted cylindrical heater.Effects of the liquid and gas velocities, the particle size, the volume ratio of floating bubble breaker to particles on phase holdup, the vertical bubble length, and the heat transfer coefficient have been determined.In the bubble-coalescing regime, the heat transfer coefficient in three-phase fluidized beds having the volume ratio V_f/V_s of 10–15% produced a maximum increase in heat transfer coefficient of about 20% in comparison to that in the bed without floating bubble breakers. Also, bubble length and gas-phase holdups exhibited their maximum and minimum values at a volume ratio of 10–15%. The heat transfer coefficient in three-phase fluidized beds of floating bubble breakers can be estimated from the surface renewal model with isotropic turbulence theory.Heat transfer coefficients expressed in terms of the Nusselt number have been correlated with the particle Reynolds number and the volume ratio of floating bubble breakers to particles.     

Influence of cycle time distribution on coating uniformity of particles in a spray fluidized bed by using CFD-DEM simulations

Cycle Time Distribution (CTD) plays a critical role for determining uniformity of particle coating in spray fluidized beds. However, the CTD is influenced by both geometrical structure and operating conditions of fluidized bed. In this study, a spray fluidized bed of coating process is simulated by a comprehensive Computational Fluid Dynamics-Discrete Element Model (CFD-DEM). To achieve different behaviors of CTD, some modifications are designed on a pseudo-2D internally circulating fluidized bed, which traditionally composes of a high-velocity upward bed and low-velocity downward bed. These modifications include making the air distributor slope and/or laying a baffle in the downward bed. First, the CTD and evolution of particle size distribution under different bed structures are compared. The CTD directly influences the coating uniformity. By making the particles flowing along a parallel direction in the downward bed through the geometrical modifications, the CTD becomes narrower and the coating uniformity is significantly improved. Second, under the optimized bed structure, the influence of operating conditions on the coating uniformity is studied. Properly increasing the fluidization gas velocity and the fluidization gas temperature and reducing the liquid spray rate can improve the coating uniformity.     

Bubble behaviors of geldart B particle in a pseudo two-dimensional pressurized fluidized bed

Pressurized fluidized beds have been developed in quite a few industrial applications because of intensified heat and mass transfer and chemical reaction. The bubble behaviors under elevated pressure, strongly influencing the fluidization and reaction conversion of the whole system, are of great research significance. In this work, the bubble behaviors of Geldart B particle in a pseudo two-dimensional (2D) pressurized fluidized bed were experimentally studied based on digital image analysis technique. The effects of pressure and fluidization gas velocity on the general bubble behaviors (i.e., size, shape and spatial distribution) and the dynamic characteristics, such as the time-evolution of voidage distribution and local flow regimes, were comprehensively investigated. Results show that increasing pressure reduces the stability of bubbles and facilitates gas passing through the emulsion phase, resulting in the “smoother” fluidization state with smaller bubbles and declined bubble fraction and standard deviation. The equivalent bubble diameter and bubble aspect ratio increase with the increasing gas velocity while decrease as pressure rises. The elevated pressure reduces bubbles extension in the vertical direction, prohibits the “short pass” of fluidization gas in large oblong bubbles/slugs and benefits the gas–solid interaction. The flow regimes variation with gas velocity is affected by the elevated pressure, and demonstrates different features in different local positions of the bed.     

Removal of dust from flue gas in magnetically stabilized fluidized bed

A magnetically stabilized fluidized bed （MSFB,Ф 500mm×2100mm） was designed to study dust removal from flue gas. Based on the mechanism of dust removal in a fixed bed, the effects on collection efficiency of magnetic field intensity, ratio of flue gas velocity to minimum fluidization velocity, bed height, and particle average diameter, were investigated. Then feasible methods for MSFB to better remove dust were proposed. Over 95 % of dust removal with MSFB can be achieved, when stable fluidization is maintained and when magnetic particles are frequently renewed.     

Effect of acoustic field on heat transfer in a sound assisted fluidized bed of fine powders

The fluidized beds are widely used in a variety of industries where heat transfer properties of the fluidized system become important for successful operation. Fluidized are preferred in heat recovery processes because of their unique ability of rapid heat transfer and uniform temperature. Fine powders handling and processing technologies have received widespread attention due to increased use of fine powders in the manufacture of drugs, cosmetics, plastics, catalysts, energetics and other advanced materials. A better understanding of fluidization behavior of fine powders is of great importance in applications involving heat transfer, mass transfer, mixing, transporting and modifying surface properties etc. The difficulty in putting the fine powders in suspension with the fluidizing gas is related to the cohesive structure and to the physical forces between the primary particles. The sound waves agitate bubbling and this results in improving solids mixing in the fluidized bed. The improved solids mixing results in uniform and smooth fluidization, which leads to better heat transfer rates in the fluidized bed.     

Fluidization and bubbling behavior of potash particles in a deep fluidized bed

Most existing models for predicting bubble size and bubble frequency have been developed for freely bubbling fluidized beds. Accurate prediction of bubbling behavior in deep fluidized beds, however, has been a challenge due to the higher degree of bubble coalescence and break up, high probability of the slugging regime, partial fluidization, and chaotic behavior in the bubbling regime. In this work, the bubbling and fluidization behavior of potash particles was investigated in a deep fluidized bed employing a twin-plane electrical capacitance tomography (ECT) system. Solid volume fraction, average bubble velocity, average bubble diameter, and bubble frequency in both bubbling and slugging regimes were measured at two different bed height ratios (H/D = 3.5 and H/D = 3.78). This work is the first to illustrate a sequential view of bubbles at different superficial gas velocities in a fluidized bed. The results show that both the bubble diameter and rising velocity increased with increasing the superficial gas velocity for the two bed heights, with larger values observed in the deeper bed compared to the shallower one. Predicted values for bubble diameter, bubble rise velocity and bubble frequency from different models are compared with the experimental data obtained from the ECT system in this work. Good agreement has been achieved between the values predicted by the previous models and the experimental data for the bubble diameter and bubble rise velocity with an average absolute deviation of 16% and 15% for the bed height of 49 cm and 13% and 8% for the bed height of 53 cm, respectively.     

Flow structure and bubble dynamics in supercritical water fluidized bed and gas fluidized bed: A comparative study

Supercritical water (SCW) fluidized bed is a new reactor concept for hydrogen production from biomass or coal gasification. In this paper, a comparative study on flow structure and bubble dynamics in a supercritical water fluidized bed and a gas fluidized bed was carried out using the discrete element method (DEM). The results show that supercritical water condition reduces the incipient fluidization velocity, changes regime transitions, i.e. a homogeneous fluidization was observed when the superficial velocity is in the range of the minimum fluidization velocity and minimum bubbling velocity even the solids behave as Geldart B powders in the gas fluidized bed. Bubbling fluidization in the supercritical water fluidized bed was formed after superficial velocity exceeds the minimum bubbling velocity, as in the gas fluidized bed. Bubble is one of the most important features in fluidized bed, which is also the emphasis in this paper. Bubble growth was effectively suppressed in the supercritical water fluidized bed, which resulted in a more uniform flow structure. By analyzing a large number of bubbles, bubble dynamic characteristics such as diameter distribution, frequency, rising path and so on, were obtained. It is found that bubble dynamic characteristics in the supercritical water fluidized bed differ a lot from that in the gas fluidized bed, and there is a better fluidization quality induced by the bubble dynamics in the supercritical water fluidized bed.     

Experimental coating and heat transfer studies in a vibrating fluidized bed

This work presents an experimental study of the heat transfer in a vibrofluidized bed and an investigation of the vibrofluidized bed coating process of thin copper plates.At superficial velocities close to that of minimum fluidization the heat transfer coefficient increases with the air flow rate and also with the immersion depth in the bed. It is independent of the initial object temperature.For different experimental conditions the obtained vibrofluidized bed coating thicknesses increase with the initial object temperature and immersion time. When compared with the theoretical predictions calculated for a regular fluidized bed, they show a good agreement. The temperature-time histories of the coated object are also recorded and compared to theoretical results.