Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber–titanium dioxide–lithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol–gel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4 × 10⁻⁵ S cm⁻¹ was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.

     

Investigations on electrical properties of PVP:KIO4 polymer electrolyte films

Solid polymer electrolytes based on poly(vinyl pyrrolidone) (PVP) complexed with potassium periodide (KIO₄) salt at different weight percent ratios were prepared using solution-cast technique. X-ray diffraction (XRD) results revealed that the amorphous nature of PVP polymer matrix increased with the increase of KIO₄ salt concentration. The complexation of the salt with the polymer was confirmed by Fourier transform infrared (FTIR) spectroscopy studies. The ionic conductivity was found to increase with the increase of temperature as well as dopant concentration. The maximum ionic conductivity (1.421 × 10⁻⁴ S cm⁻¹) was obtained for 15 wt% KIO₄ doped polymer electrolyte at room temperature. The variation of ac conductivity with frequency obeyed Jonscher power law. The dynamical aspects of electrical transport process in the electrolyte were analyzed using complex electrical modulus. The peaks found in the electric modulus plots have been characterized in terms of the stretched exponential parameter. Optical absorption studies were performed in the wavelength range 200–600 nm and the absorption band energies (direct band gap and indirect band gap) values were evaluated. Using these polymer electrolyte films electrochemical cells were fabricated and their discharge characteristics were studied.     

Structure and ion transport in an ethylene carbonate-modified biodegradable gel polymer electrolyte

The influence of ethylene carbonate (EC) addition on 85poly(ε-caprolactone):15Lithium thiocyanate (85PCL:15LiSCN) polymer electrolyte is investigated using X-ray diffraction, impedance spectroscopy, Wagner's polarization and electrochemical measurements. The results reveal that the amorphicity of the 85PCL:15LiSCN system increases with increase of EC content up to an optimal level of 40 wt.%. This is reflected in the electrical properties of the gel polymer electrolytes, i.e., the 40 wt.% EC-incorporated gel polymer electrolyte exhibits both high amorphicity and high electrical conductivity as compared to the other samples. The EC concentration dependences of dielectric constant and electrical conductivity show a similar trend, indicating that these properties are closely related to each other. The total ionic transference numbers of EC-incorporated gel polymer electrolytes are in the range 0.989–0.993, demonstrating that they are almost completely ionic conductors. The electrochemical stability window of the 40 wt.% EC-incorporated gel polymer electrolyte is ∼4.1 V along with the electrical conductivity of 2.2 × 10⁻⁴ S cm⁻¹, which is significantly improved as compared to the 85PCL:15LiSCN system (3.0 V and 1.04 × 10⁻⁶ S cm⁻¹). Consequently, the addition of EC in the 85PCL:15LiSCN polymer electrolyte leads to a promising improvement in its various properties.     

Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber�Ctitanium dioxide�Clithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol?Cgel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4?×?10^?5 S cm^?1 was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.     

Characterization and properties of ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes

Gel polymer electrolytes containing 1-ethyl-3-methylimidazolium-bis (trifluoromethyl-sulfnyl)imide (EMITFSI) ionic liquid were prepared for lithium ion batteries by solution casting method. Thermal and electrochemical properties have been determined for the gel polymer electrolytes. Proper addition of EMITFSI to the P(VdF-HFP)-LiTFSI polymer electrolyte improves the ionic conductivity and electrochemical window to 2.11 × 10⁻³ S cm⁻¹ (30 °C) and 4.6 V. In combination of the prepared ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes, Li₄Ti₅O₁₂ anode exhibited two extra voltage plateaus around 1.1 V and 2.3 V except the typical voltage plateau around 1.6 V by possible side reaction between ionic liquid and polymer. LiFePO₄ cathode exhibited high capacity above 140 mA h g⁻¹ and retention of 93.1% due to the suppressed polarization effect caused by enhanced ion transport properties. The high temperature of 80 °C didn't have significant impact on the cycling performance.     

Synthesis and characterization of electrospun PVdF-HFP/silane-functionalized ZrO2 hybrid nanofiber electrolyte with enhanced optical and electrochemical properties

A facile method to produce a hybrid of organic-inorganic nanofiber electrolyte via electrospinning is hereby presented. The incorporation of functionalized zirconium oxide (ZrO₂) nanoparticles into poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP) and complexed with lithium trifluoromethanesulfonate (LiCF₃SO₃) provided an enhanced optical transmissivity and ionic conductivity. The dependence of the nanofiber's morphology, optical and electrochemical properties on the various ZrO₂ loading was studied. Results show that while nanofiller content was increased, the diameter of the nanofibers was reduced. The improved bulk ionic conductivity of the nanofiber electrolyte was at 1.96 × 10⁻⁵ S cm⁻¹. Owing to the enhanced dispersibility of the 3-(trimethoxysilyl)propyl methacrylate (MPS) functionalized ZrO₂, the optical transmissivity of the nanofiber electrolyte was improved significantly. This new nanofiber composite electrolyte membrane with further development has the potential to be next generation electrolyte for energy efficient windows like electrochromic devices.     

Electrodeposition and stripping of zinc from an ionic liquid polymer gel electrolyte for rechargeable zinc-based batteries

In this paper, we report on zinc deposition and stripping in an ionic liquid polymer gel electrolyte on gold and copper substrates, respectively. The ionic liquid-based polymer gel electrolyte is prepared by combining the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate ([Py_1,4]TfO), with Zn(TfO)₂ and poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP). The ionic liquid polymer gel electrolyte exhibits good conductivity (2.2 mS cm^?1) and good mechanical stability. Zinc deposition and stripping in the ionic liquid polymer gel electrolyte were studied by cyclic voltammetry, potentiostatic, and galvanostatic cycling (charging/discharging) experiments. The gel electrolyte exhibits a promising electrochemical stability and allows a quasi-reversible zinc deposition/stripping. The morphology of the zinc deposits after 10 cycles of zinc deposition/stripping is compact and dense, and deposits without any dendrite formation can be obtained. The quasi-reversibility of the electrochemical deposition/stripping of zinc in this ionic liquid polymer gel electrolyte is of interest for rechargeable zinc-based batteries.     

Simultaneous electrodeposition behavior of dysprosium and terbium in 1-ethyl-3-methyl-imidazolium tetrafluoroborate ionic liquid

The simultaneous electrodeposition of dysprosium and terbium on platinum electrode in 1-ethyl-3-methyl-imidazolium tetrafluoroborate (EMIMBF₄) ionic liquid was investigated. The cyclic voltammetry, chronoamperometry and constant electrolysis experiments have been employed to examine the electrochemistry of dysprosium and terbium ions in 0.01 mol/L DyCl₃-0.023 mol/L TbCl₃-0.27 mol/L LiCl-EMIMBF₄ ionic liquid. The electrochemistry experiments indicated that the reduction of dysprosium and terbium ions in 0.01 mol/L DyCl₃-0.023 mol/L TbCl₃-0.27 mol/L LiCl-EMIMBF₄ ionic liquid was an irreversible process and simultaneous process. In 0.01 mol/L DyCl₃-0.023 mol/L TbCl₃-0.27 mol/L LiCl-EMIMBF₄ ionic liquid the diffusion coefficient of the diffusion process of species which controlled the total electrochemical reduction process have been determined to be (3.79–7.07) × 10⁻⁶ cm²/s from cyclic voltammetry and chronoamperometry results. XRD spectrum of constant electrolysis samples showed that dysprosium and terbium deposits were obtained.     

Low-temperature performance of Li-ion cells with a LiBF<Subscript>4</Subscript>-based electrolyte

The effect of LiBF₄ on the low-temperature performance of a Li-ion cell was studied by using a 1:1:1 (wt) EC/DMC/DEC mixed solvent. The results show that the LiBF₄-based electrolyte has a 2- to 3-fold lower ionic conductivity and shows rather higher freezing temperature compared with a LiPF₆-based electrolyte. Owing to electrolyte freezing, cycling performance of the Li-ion cell using LiBF₄ was significantly decreased when the temperature fell below –20 °C. However, impedance data show that at –20 °C the LiBF₄ cell has lower charge-transfer resistance than the LiPF₆ cell. In spite of the relatively lower conductivity of the LiBF₄-based electrolyte, the cell based on it shows slightly lower polarization and higher capacity in the liquid temperature range (above –20 °C) of the electrolyte. This fact reveals that ionic conductivity of the electrolytes is not a limitation to the low-temperature performance of the Li-ion cell. Therefore, LiBF₄ may be a good salt for the low-temperature electrolyte of a Li-ion cell if a solvent system that is of low freezing temperature, high solubility to LiBF₄, and good compatibility with a graphite anode can be formulated. Electronic Publication     

Synthesis and electrochemical characterization of aPEO-based polymer electrolytes

In this paper, the preparation and purification of an amorphous polymer network, poly[oxymethylene-oligo(oxyethylene)], designated as aPEO, are described. The flexible CH₂CH₂O segments in this host polymer combine appropriate mechanical properties, over a critical temperature range from −20 to 60 °C, with labile salt-host interactions. The intensity of these interactions is sufficient to permit solubilisation of the guest salt in the host polymer while permitting adequate mobility of ionic guest species. We also report the preparation and characterisation of a novel polymer electrolyte based on this host polymer with lithium tetrafluoroborate, LiBF₄, as guest salt. Electrolyte samples are thermally stable up to approximately 250 °C and completely amorphous above room temperature. The electrolyte composition determines the glass transition temperature of electrolytes and was found to vary between −50.8 and −62.4 °C. The electrolyte composition that supports the maximum room temperature conductivity of this electrolyte system is n = 5 (2.10 × 10⁻⁵ S cm⁻¹ at 25 °C). The electrochemical stability domain of the sample with n = 5 spans about 5 V measured against a Li/Li⁺ reference. This new electrolyte system represents a promising alternative to LiCF₃SO₃ and LiClO₄-doped PEO analogues.     

Ion Conducting Polyethylene Oxide-Based Polymer Electrolyte Dopped with Ionic Liquid-Trifluoromethanesulfonic Chloride

In last few decades, polymer electrolyte is the most promising candidate for the fabrication of electrochemical devices. In current work, the influence of adding the room-temperature ionic liquid (trifluoromethanesulfonic chloride – CClF3O2S) in polyethylene oxide (PEO): ammonium iodide (NH4I) polymer electrolyte has been studied. The IL-doped polymer electrolyte films are synthesized by solution casting method with varying stoichiometric ratios. Several experimental techniques including optical polarizing microscope, impedance spectroscopy, X-ray diffraction, Linear sweep voltammetry, Ionic transference number thermal analysis, and electrical conductivity measurements at room temperature have been studied in detail. The complex material's maximum conductivity has been determined to be 3.3 × 10⁻⁵ S cm⁻¹ at room temperature. The POM images show the increase in amorphous region which further confirm the improvement in ionic conductivity. Ionic transference number 0.96 shows the system is purely ionic in nature. The ESW of the IL doped polymer electrolyte is also sawed to be 3.32 V which is suitable for the fabrication of electrochemical devices.     

Effect of adding ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate on the coordination environment of Li<Superscript>+</Superscript> ions in propylene carbonate,according to data from IR spectroscopy and quantum chemical modeling

The effect ionic liquid (IL) 1-ethyl-3-methylimidazolium tetrafluoroborate has on the coordination environment of Li⁺ cations in carbonate solvents is studied by means of IR spectroscopy and quantum chemical modeling using the example of propylene carbonate (PC). LiBF₄ is used as the lithium salt. This system is promising for use as an electrolyte in lithium power sources (LPSs), but the mechanism of ionic conductivity by Li⁺ ions in such systems has yet to be studied in full.     

PVDF-HFP composite polymer electrolyte with excellent electrochemical properties for Li-ion batteries

Poly (vinylidene fluoride-co-hexafluoropropylene)-based composite polymer electrolyte (CPE) was prepared by phase inversion technique. In this work, we first applied a novel surface-modified sub-micro-sized alumina, PC-401, as ceramic filler. Various electrochemical methods were applied to investigate the electrochemical properties of the polymer electrolytes. We found that the CPE with 10 wt.% PC-401 has excellent electrochemical properties, including the ionic conductivity as high as 0.89 mS cm⁻¹ and the Li-ion transference number of 0.46. Polymer Li-ion batteries using LiFePO₄ as cathode active material exhibited excellent cycling and high-temperature performances. PC-401 shows a promising applicability in the preparation of polymer electrolyte with high electrochemical properties.     

Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

Mechanical and Electrochemical Properties of New Nanocomposite Polymer Electrolytes Based on Poly(vinylidene fluoride-co-hexafluoropropylene) and SiO<Subscript>2</Subscript> Addition

Nanocomposite polymer electrolytes based on the system poly(vinylidene fluoride-co-hexafluoropropylene)–liquid electrolyte 1 mol/L LiBF₄ in gamma-butyrolactone which is modified by introducing up to 10 wt % of SiO₂ nanopowder (an average particle size of 7 nm) are synthesized and characterized. The introduction of SiO₂ nanoparticles worsens the elasticity of films but increases their fracture stress to 24 MPa. The conductivity of the nanocomposite electrolytes containing SiO₂ nanoparticles is higher than that without SiO₂ and attains 3.7 mS/cm at 20°C for the electrolyte containing 1.25 wt % SiO₂. Upon the introduction of SiO₂ nanoparticles, the electrochemical stability of electrolytes grows by 0.50–0.85 V and attains 6.7 V relative to Li/Li⁺.     

Effect of NiO nanofiller concentration on the properties of PEO-NiO-LiClO4 composite polymer electrolyte

Composite polymer electrolyte films comprising polyethylene oxide (PEO) as the polymer host, LiClO₄ as the dopant, and NiO nanoparticle as the inorganic filler was prepared by solution casting technique. NiO inorganic filler was synthesized via sol-gel method. The effect of NiO filler on the ionic conductivity, structure, and morphology of PEO-LiClO₄-based composite polymer electrolyte was investigated by AC impedance spectroscopy, X-ray diffraction, and scanning electron microscopy, respectively. It was observed that the conductivity of the electrolyte increases with NiO concentration. The highest room temperature conductivity of the electrolyte was 7.4?×?10^?4 S cm^?1 at 10 wt.% NiO. The observation on structure shows the highest conductivity appears in amorphous phase. This result has been supported by surface morphology analysis showing that the NiO filler are well distributed in the samples. As a conclusion, the addition of NiO nanofiller improves the conductivity of PEO-LiClO₄ composite polymer electrolyte.     

Enhanced zinc ion transport in gel polymer electrolyte: effect of nano-sized ZnO dispersion

The effect of the dispersion of zinc oxide (ZnO) nanoparticles in the zinc ion conducting gel polymer electrolyte is studied. Changes in the morphology/structure of the gel polymer electrolyte with the introduction of ZnO particles are distinctly observed using X-ray diffraction and scanning electron microscopy. The nanocomposites offer ionic conductivity values of >10^?3 S cm^?1 with good thermal and electrochemical stabilities. The variation of ionic conductivity with temperature follows the Vogel–Tamman–Fulcher behavior. AC impedance spectroscopy, cyclic voltammetry, and transport number measurements have confirmed Zn²⁺ ion conduction in the gel nanocomposites. An electrochemical stability window from ?2.25 to 2.25 V was obtained from voltammetric studies of nanocomposite films. The cationic (i.e., Zn²⁺ ion) transport number (t ₊) has been found to be significantly enhanced up to a maximum of 0.55 for the dispersion of 10 wt.% ZnO nanoparticles, indicating substantial enhancement in Zn²⁺ ion conductivity. The gel polymer electrolyte nanocomposite films with enhanced Zn²⁺ ion conductivity are useful as separators and electrolytes in Zn rechargeable batteries and other electrochemical applications.     

Preparation and characterization of blended solid polymer electrolyte 49% poly(methyl methacrylate)-grafted natural rubber:poly(methyl methacrylate)–lithium tetrafluoroborate

The preparation and characterization of blended solid polymer electrolyte 49% poly(methyl methacrylate)-grafted natural rubber (MG49):poly(methyl methacrylate) (PMMA) (30:70) were carried out. The effect of lithium tetrafluoroborate (LiBF₄) concentration on the chemical interaction, structure, morphology, and room temperature conductivity of the electrolyte were investigated. The electrolyte samples with various weight percentages (wt.%) of LiBF₄ salt were prepared by solution casting technique and characterized by Fourier transform infrared spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy. Infrared analysis demonstrated that the interaction between lithium ions and oxygen atoms occurred at symmetrical stretching of carbonyl (C=O) (1,735 cm^?1) and asymmetric deformation of (O–CH₃) (1,456 cm^?1) via the formation of coordinate bond on MMA structure in MG49 and PMMA. The reduction of MMA peaks intensity at the diffraction angle, 2θ of 29.5° and 39.5° was due to the increase in weight percent of LiBF₄. The complexation occurred between the salt and polymer host had been confirmed by the XRD analysis. The semi-crystalline phase of polymer host was found to reduce with the increase in salt content and confirmed by XRD analysis. Morphological studies by SEM showed that MG49 blended with PMMA was compatible. The addition of salt into the blend has changed the topological order of the polymer host from dark surface to brighter surface. The SEM analyses supported the enhancement of conductivity with the addition of salt. The conductivity increased drastically from 2.0 to 3.4?×?10^?5 S cm^?1 with the addition of 25 wt.% of salt. The increase in the conductivity was due to the increasing of the number of charge carriers in the electrolyte. The conductivity obeys Arrhenius equation in higher temperature region from 333 to 373 K with the pre-exponential factor σ _o of 1.21?×?10^?7 S cm^?1 and the activation energy E _a of 0.46 eV. The conductivity is not Arrhenian in lower temperature region from 303 to 323 K.     

Effect of ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide on the properties of poly(glycidyl methacrylate) based solid polymer electrolytes

A free standing polymer electrolytes films, containing poly(glycidyl methacrylate) (PGMA) as the polymer host, lithium perchlorate (LiClO₄), and ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl) imide [Bmim][TFSI] as a plasticizer was successfully prepared via the solution casting method. The XRD analysis revealed the amorphous nature of the electrolyte. ATR-FTIR and thermal studies confirmed the interaction and complexation between the polymer host and the ionic liquid. The maximum ionic conductivity of the solid polymer electrolyte was found at 2.56 × 10^–5 S cm^–1 by the addition of 60 wt % [Bmim][TFSI] at room temperature and increased up to 3.19 × 10^–4 S cm^–1 at 373 K, as well as exhibited a transition of temperature dependence of conductivity: Arrhenius-like behavior at low and high temperatures.     

Improved properties of polymer electrolyte by ionic liquid PP1.3TFSI for secondary lithium ion battery

A new kind of polymer electrolyte is prepared from N-methyl-N-propylpiperidinium bis (trifluoromethanesulfonyl) imide (PP1.3TFSI), polyethylene oxide (PEO), and lithium bis (trifluoromethanesulfonyl) imide (LiTFSI). IR and X-ray diffraction results demonstrate that the addition of ionic liquid decreases the crystallization of PEO. Thermal and electrochemical properties have been tested for the solid polymer electrolytes, the addition of the room temperature molten salt PP1.3TFSI to the conventional P(EO)₂₀LiTFSI polymer electrolyte leads to the improvement of the thermal stability and the ionic conductivity (x = 1.27, 2.06 × 10⁻⁴ S cm⁻¹ at room temperature), and the reasonable lithium transference number is also obtained. The Li/LiFePO₄ cell using this polymer electrolyte shows promising reversible capacity, 120 mAh g⁻¹ at room temperature and 164 mAh g⁻¹ at 55 °C.