Analysis of droplet transfer mode and forming process of weld bead in CO2 laser–MAG hybrid welding process

In this paper, CO₂ laser–metal active gas (MAG) hybrid welding technique is used to weld high strength steel and the optimized process parameters are obtained. Using LD Pumped laser with an emission wavelength of 532 nm to overcome the strong interference from the welding arc, a computer-based system is developed to collect and visualize the waveforms of the electrical welding parameters and metal transfer processes in laser–MAG. The welding electric signals of hybrid welding processes are quantitatively described and analyzed using the ANALYSATOR HANNOVER. The effect of distance between laser and arc (D_LA) on weld bead geometry, forming process of weld shape, electric signals, arc characteristic and droplet transfer behavior is investigated. It is found that arc characteristic, droplet transfer mode and final weld bead geometry are strongly affected by the distance between laser and arc. The weld bead geometry is changed from “cocktail cup” to “cone-shaped” with the increasing D_LA. The droplet transfer mode is changed from globular transfer to projected transfer with the increasing D_LA. Projected transfer mode is an advantage for the stability of hybrid welding processes.     

Welded joints integrity analysis and optimization for fiber laser welding of dissimilar materials

Dissimilar materials welded joints provide many advantages in power, automotive, chemical, and spacecraft industries. The weld bead integrity which is determined by process parameters plays a significant role in the welding quality during the fiber laser welding (FLW) of dissimilar materials. In this paper, an optimization method by taking the integrity of the weld bead and weld area into consideration is proposed for FLW of dissimilar materials, the low carbon steel and stainless steel. The relationships between the weld bead integrity and process parameters are developed by the genetic algorithm optimized back propagation neural network (GA-BPNN). The particle swarm optimization (PSO) algorithm is taken for optimizing the predicted outputs from GA-BPNN for the objective. Through the optimization process, the desired weld bead with good integrity and minimum weld area are obtained and the corresponding microstructure and microhardness are excellent. The mechanical properties of the optimized joints are greatly improved compared with that of the un-optimized welded joints. Moreover, the effects of significant factors are analyzed based on the statistical approach and the laser power (LP) is identified as the most significant factor on the weld bead integrity and weld area. The results indicate that the proposed method is effective for improving the reliability and stability of welded joints in the practical production.     

Microstructure characteristics of laser-MIG hybrid welded mild steel

To deepen the understanding of laser-arc hybrid welding, the weld shape and microstructure characteristics of laser-metal inert gas hybrid welded mild steel were analyzed. The results showed typical hybrid weld could be classified as two parts: the wide upper zone and the narrow nether zone, which were defined as arc zone and laser zone, respectively. In the hybrid weld, the microstructure, alloy element distribution and microhardness all have evident difference between laser zone and arc zone. The microstructure of arc zone consists of coarse columnar dendrite and fine acicular dendrite between the columnar dendrites, but that of laser zone is composed of fine equiaxed dendrite in weld center and columnar dendrite around the equiaxed dendrite. Compared to arc zone, laser zone has finer grain size, higher microhardness, smaller alloy element content in the fusion zone and narrower heat affected zone. The discussions demonstrated that the observed difference was caused by the difference of temperature gradient, crystallizing and the effects of arc pressure on the molten pool between laser zone and arc zone.     

5083铝合金光纤激光-TIG复合焊接工艺研究

采用IPG YLS-6000光纤激光器和Fronius MagicWave3000job数字化焊机,对4mm厚5083H116铝合金进行了复合焊接试验。研究了电源特性、电流大小和热源间距等工艺参数对光纤激光-钨极惰性气体保护焊(TIG)复合焊接焊缝成形的影响规律,并分析了焊接接头的缺陷、显微硬度及力学性能。结果表明,光纤激光-TIG复合焊接5083铝合金,能够明显改善焊缝成形,提高焊接过程稳定性,特别是与变极性TIG电弧复合效果更为显著;光纤激光与变极性TIG电弧复合焊接,采用激光在前的方式,电弧电流150A,且热源间距不大于4mm,可以得到具有明亮金属光泽和均匀鱼鳞纹的焊缝,焊缝无气孔和裂纹缺陷,其表面有少量的下凹;复合焊接接头抗拉强度为318MPa,达到母材强度的93%,延伸率为7.6%,高于单光纤激光焊接,断口分析为韧性断裂。     

Effect of Laser Pulse on Arc Plasma and Magnesium Target in Low-Power Laser/Arc Hybrid Welding

Low-power laser/arc hybrid welding process of magnesium alloy shows that the weld capability of tungsten-inert-gas arc is improved under the action of laser pulses. The effect of laser pulse on arc plasma is analyzed by studying the plasma spectra, plasma shapes, and arc voltage in this paper. On the one hand, laser pulse attracts arc plasma to laser keyhole and improves the stability of arc plasma; on the other hand, laser pulse expands the arc plasma and concentrates the electric conducting route of arc plasma. All these increase the output power and energy density of arc plasma, so the welding penetration is improved. In addition, laser pulses are controlled to act on the negative wave of alternating-current arc (the target metal has negative polarity) in hybrid welding process to improve the stability of arc plasma and weld penetration.      

Parametric optimisation and microstructural analysis on high power Yb-fibre laser welding of Ti–6Al–4V

In this work thin sheets of Ti–6Al–4V were full penetration welded using a 5 kW fibre laser in order to evaluate the effectiveness of high power fibre laser as a welding processing tool for welding Ti–6Al–4V with the requirements of the aircraft industry and to determine the effect of welding parameters including laser power, welding speed and beam focal position on the weld microstructure, bead profile and weld quality. It involved establishing an understanding of the influence of welding parameters on microstructural change, welding defects, and the characteristics of heat affected zone (HAZ) and weld metal (WM) of fibre laser welded joints. The optimum range of welding parameters which produced welds without cracking and porosity were identified. The influence of the welding parameters on the weld joint heterogeneity was characterised by conducting detailed microstructural analysis.     

An investigation on capability of hybrid Nd:YAG laser-TIG welding technology for AA2198 Al-Li alloy

This paper surveys the capability of the hybrid laser-arc welding in comparison with lone laser welding for AA2198 aluminum alloy experimentally. In the present research, a continuous Nd:YAG laser with a maximum power of 2000 W and a 350 A electric arc were used as two combined welding heat sources. In addition to the lone laser welding experiments, two strategies were examined for hybrid welding; the first one was low laser power (100 W) accompanied by high arc energy, and the second one was high laser power (2000 W) with low arc energy. Welding speed and arc current varied in the experiments. The influence of heat input on weld pool geometry was surveyed. The macrosection, microhardness profile and microstructure of the welded joints were studied and compared. The results indicated that in lone laser welding, conduction mode occurred and keyhole was not formed even in low welding speeds and thus the penetration depth was so low. It was also found that the second approach (high laser power accompanied with low arc energy) is superior to the first one (low laser power accompanied with high arc energy) in hybrid laser-arc welding of Al2198, since lower heat input was needed for full penetration weld and as a result a smaller HAZ was created.     

Influences of laser in low power YAG laser-MAG hybrid welding process

The influences of laser defocusing amount △z, laser power P, space distance DLA between laser and arc on weld penetration, arc modality and stability are investigated in low power YAG laser and metal active gas （laser-MAG） hybrid welding process. The experimental results indicate that the effects of laser-induced attraction and contraction of MAG arc are emerged in hybrid welding process, which result in the augmentation of hybrid welding energy. When DLA ： -0.5 - 2 mm, △z = -2 - 2 mm and P ≥ 73 W, the synergic efficiency between laser and MAG arc is obvious, the cross section at the root of hybrid arc is contracted and the hybrid weld penetration is increased. The maximal ratio of hybrid/MAG weld penetration is 1.5 and the lowest YAG laser power that augments MAG arc is 73 W. The input of YAG laser makes the stabilities of arc ignition and combustion prominent in hybrid welding process.     

高温合金活性剂激光微焊接接头的组织性能研究

采用配方均匀设计法,配制了SiO2-MnO2-CaO-TiO2-CaF2-NaF多组元活性剂,利用微型脉冲激光器对500 m厚GH4169高温合金进行了活性剂激光焊接试验。分析并讨论了焊接接头的显微组织和力学性能。试验结果表明,与传统激光焊相比,所配制的20种活性剂均增加了焊缝熔深,并且其中F12系混合活性剂增加熔深能力最为显著,使焊缝深宽比增加了159%,证明通过使用活性剂来增加微激光焊焊缝熔深,降低高温合金板激光焊接的成本是可行的。在活性剂作用下,焊缝显微组织仍由柱状晶和等轴晶组成,接头抗拉强度达到927 MPa,为母材强度的92.7%。     

Optimization of hybrid laser – TIG welding of 316LN steel using response surface methodology (RSM)

In the present study, the hybrid laser – TIG welding parameters for welding of 316LN austenitic stainless steel have been investigated by combining a pulsed laser beam with a TIG welding heat source at the weld pool. Laser power, pulse frequency, pulse duration, TIG current were presumed as the welding process parameters whereas weld bead width, weld cross-sectional area and depth of penetration (DOP) were considered as the process responses. Central composite design was used to complete the design matrix and welding experiments were conducted based on the design matrix. Weld bead measurements were then carried out to generate the dataset. Multiple regression models correlating the process parameters with the responses have been developed. The accuracy of the models were found to be good. Then, the desirability approach optimization technique was employed for determining the optimum process parameters to obtain the desired weld bead profile. Validation experiments were then carried out from the determined optimum process parameters. There was good agreement between the predicted and measured values.     

Influence of shielding gas pressure on welding characteristics in CO2 laser-MIG hybrid welding process

The droplet transfer behavior and weld characteristics have been investigated under different pressures of shielding gas in CO2 laser and metal inert/active gas (laser-MIG) hybrid welding process. The experimental results indicate that the inherent droplet transfer frequency and stable welding range of conventional MIG arc are changed due to the interaction between CO2 laser beam and MIG arc in laser-MIG hybrid welding process, and the shielding gas pressure has a crucial effect on welding characteristics. When the pressure of shielding gas is low in comparison with MIG welding, the frequency of droplet transfer decreases, and thedroplet transfer becomes unstable in laser-MIG hybrid welding. So the penetration depth decreases, which shows the characteristic of unstable hybrid welding. However, when the pressure of shielding gas increases to a critical value, the hybrid welding characteristic is changed from unstable hybrid welding to stablehybrid welding, and the frequency of droplet transfer and the penetration depth increase significantly.     

Microstructure evolution and mechanical property of pulsed laser welded Ni-based superalloy

For evaluating the microstructure evolution and mechanical property of Ni-based Hastelloy C-276 weld joint by the pulsed laser welding, the influence of pulsed laser welding on the microstructure and mechanical property of the weld joint is investigated by the analysis of the microstructure morphology, microhardness, phase structure and tensile property. The results indicate that, in the fusion zone three sections are divided on the basis of the patterns of grain structures. In the weld joint, the element segregation is found, but the trend of brittle phase׳s formation is weakened. The weld microhardness presents just a little higher than that of base metal, and there is no obvious the softened heat affected zone. Meanwhile in the weld joint, the phase structure is still the face-center cubic with the tiny shift of peak positions and widened Full Width at Half-Maximum. The yield strength of weld joint is the same as that of base metal, and the tensile strength is nearly 90% of that of base metal. The decreased tensile strength is mainly attributed to the dislocation piling-up.     

Improvement of laser keyhole formation with the assistance of arc plasma in the hybrid welding process of magnesium alloy

In the previous work, low-power laser/arc hybrid welding technique is used to weld magnesium alloy and high-quality weld joints are obtained. In order to make clear the interactions between low-power laser pulse and arc plasma, the effect of arc plasma on laser pulse is studied in this article. The result shows that the penetration of low-power laser welding with the assistance of TIG arc is more than two times deeper than that of laser welding alone and laser welding transforms from thermal-conduction mode to keyhole mode. The plasma behaviors and spectra during the welding process are studied, and the transition mechanism of laser-welding mode is analyzed in detail. It is also found that with the assistance of arc plasma, the threshold value of average power density to form keyhole welding for YAG laser is only 3.3×10⁴ W/cm², and the average peak power density is 2.6×10⁵ W/cm² in the present experiment. Moreover, the distribution of energy density during laser pulse is modulated to improve the formation and stability of laser keyholes.     

Effect of heat input on microstructure and properties of hybrid fiber laser-arc weld joints of the 800 MPa hot-rolled Nb-Ti-Mo microalloyed steels

Hybrid fiber laser-arc welding (HLAW) process was applied to a novel hot-rolled Nb-Ti-Mo microalloyed steels of 8 mm thickness. The steel is primarily used to manufacture automotive and construction machinery components, etc. To elucidate the effect of heat input on geometry, microstructure and mechanical properties, different heat inputs (3.90, 5.20 and 7.75 kJ/cm) were used by changing the welding speeds. With increased heat input, the depth/width of penetration was decreased, and the geometry of fusion zone (FZ) changed to “wine cup-like” shape. In regard to the microstructural constituents, the martensite content was decreased, but granular bainite (GB) content was increased. The main microstructural difference was in the FZ cross-section at 7.75 kJ/cm because of the effect of thermal source on the top and bottom. The microstructure of the top part consisted of GB, grain boundary ferrite, and acicular ferrite, while the bottom part was primarily lath martensite. The hardness distribution was similar for different heat inputs. Hardness in FZ, coarse-grained HAZ and mixed-grained HAZ was higher than the base metal (BM), but for the fine-grained HAZ was similar or marginally less than the base metal (BM). Tensile strain was concentrated in the BM such that the fracture occurred in this region. In summary, the geometry, microstructure, and mechanical properties of weld joints were superior at heat input of 5.20 kJ/cm.     

Laser welding of thin foil nickel-titanium shape memory alloy

In this study, two L27 Taguchi experiments were carried out to study the effect of fibre laser welding parameters and their interactions upon the weld bead aspect ratio of nickel-titanium thin foil. The optimum parameters to produce full penetrated weld with the largest aspect ratio and desirable microstructure were successfully obtained by the Taguchi experimental design. The corrosion property of the optimized NiTi weld in Hank’s solution at 37.5 °C was studied and compared with the as-received NiTi. To improve the corrosion properties of the weld, the effect of post-weld-heat-treatments ranging from 573 to 1173 K was investigated. The corrosion properties, surface morphology, microstructure and Ti/Ni ratio of the heat-treated NiTi weld were analysed. It was found that a post-weld heat treatment at 573 K for 1 h provided the best pitting corrosion resistance at the weld zone.     

Multi-objective optimization of weld geometry in hybrid fiber laser-arc butt welding using Kriging model and NSGA-II

An integrated multi-objective optimization approach combining Kriging model and non-dominated sorting genetic algorithm-II (NSGA-II) is proposed to predict and optimize weld geometry in hybrid fiber laser-arc welding on 316L stainless steel in this paper. A four-factor, five-level experiment using Taguchi L₂₅ orthogonal array is conducted considering laser power (P), welding current (I), distance between laser and arc (D) and traveling speed (V). Kriging models are adopted to approximate the relationship between process parameters and weld geometry, namely depth of penetration (DP), bead width (BW) and bead reinforcement (BR). NSGA-II is used for multi-objective optimization taking the constructed Kriging models as objective functions and generates a set of optimal solutions with pareto-optimal front for outputs. Meanwhile, the main effects and the first-order interactions between process parameters are analyzed. Microstructure is also discussed. Verification experiments demonstrate that the optimum values obtained by the proposed integrated Kriging model and NSGA-II approach are in good agreement with experimental results.     

Improved microstructure and mechanical properties in gas tungsten arc welded aluminum joints by using graphene nanosheets/aluminum composite filler wires

In the present study, different amounts of graphene nanosheets (GNSs) were added to the 4043 aluminum alloy powders by using the mechanical alloying method to produce the composite filler wires. With each of the produced composite filler wires, one all-weld metal coupon was welded using the gas tungsten arc (GTA) welding process. The microstructure, mechanical properties and fracture surface morphology of the weld metals have been evaluated and the results are compared. As the amount of GNSs in the composition of filler wire is increased, the microstructure of weld metal was changed from the dendritic structure to fine equiaxed grains. Furthermore, the tensile strength and microhardness of weld metal was improved, and is attributed to the augmented nucleation and retarded growth. From the results, it was seen that the GNSs/Al composite filler wire can be used to improve the microstructure and mechanical properties of GTA weld metals of aluminum and its alloys.     

Comparison of microstructure and mechanical properties of ultra-narrow gap laser and gas-metal-arc welded S960 high strength steel

The microstructural characteristics and mechanical properties, including micro-hardness, tensile properties, three-point bending properties and Charpy impact toughness at different test temperatures of 8 mm thick S960 high strength steel plates were investigated following their joining by multi-pass ultra-narrow gap laser welding (NGLW) and gas metal arc welding (GMAW) techniques. It was found that the microstructure in the fusion zone (FZ) for the ultra-NGLW joint was predominantly martensite mixed with some tempered martensite, while the FZ for the GMAW joint was mainly consisted of ferrite with some martensite. The strength of the ultra-NGLW specimens was comparable to that of the base material (BM), with all welded specimens failed in the BM in the tensile tests. The tensile strength of the GMAW specimens was reduced approximately by 100 MPa when compared with the base material by a broad and soft heat affected zone (HAZ) with failure located in the soft HAZ. Both the ultra-NGLW and GMAW specimens performed well in three-point bending tests. The GMAW joints exhibited better impact toughness than the ultra-NGLW joints.     

Optimal design for laser beam butt welding process parameter using artificial neural networks and genetic algorithm for super austenitic stainless steel

Laser welding input parameters play a very significant role in determining the quality of a weld joint. The joint quality can be defined in terms of properties such as weld bead geometry, mechanical properties and distortion. Therefore, mechanical properties should be controlled to obtain good welded joints. In this study, the weld bead geometry such as depth of penetration (DP), bead width (BW) and tensile strength (TS) of the laser welded butt joints made of AISI 904L super austenitic stainless steel were investigated. Full factorial design was used to carry out the experimental design. Artificial Neural networks (ANN) program was developed in MatLab software to establish the relationships between the laser welding input parameters like beam power, travel speed and focal position and the three responses DP, BW and TS in three different shielding gases (Argon, Helium and Nitrogen). The established models were used for optimizing the process parameters using Genetic Algorithm (GA). Optimum solutions for the three different gases and their respective responses were obtained. Confirmation experiment has also been conducted to validate the optimized parameters obtained from GA.     

Interactions between laser and arc plasma during laser–arc hybrid welding of magnesium alloy

This paper presents the results of the investigation on the interactions between laser and arc plasma during laser–arc hybrid welding on magnesium alloy AZ31B using the spectral diagnose technique. By comparably analyzing the variation in plasma information (the shape, the electron temperature and density) of single tungsten inert gas (TIG) welding with the laser–arc hybrid welding, it is found that the laser affects the arc plasma through the keyhole forming on the workpiece. Depending on the welding parameters there are three kinds of interactions taking place between laser and arc plasma.