Defect chemistry and oxygen transport of (La0.6Sr0.4 − xMx)0.99Co0.2Fe0.8O3 − δ, M = Ca (x = 0.05, 0.1), Ba (x = 0.1, 0.2), Sr: Part I: Defect chemistry

This paper is the first part of a two part series, where the effects of varying the A-site dopant on the defect chemistry, the diffusion coefficient and the surface catalytic properties of the materials (La_0.6Sr_0.4 − xM_x)_0.99Co_0.2Fe_0.8O_3 − δ, M = Sr, Ca (x = 0.05, 0.1), Ba (x = 0.1, 0.2) (LSMFC) have been investigated. In part I, the findings on the defect chemistry are reported, while the transport properties are reported in part II. Substitution of Sr²⁺ ions with Ca²⁺ ions (smaller ionic radius) and Ba²⁺ ions (larger ionic radius) strains the crystal structure differently for each composition while keeping the average valence of the cations constant. The Ba²⁺ containing materials show the largest oxygen loss at elevated temperatures, while the purely Sr²⁺ doped material showed the smallest oxygen loss. This was reflected in the partial oxidation entropy of the materials. The measured oxygen loss was modelled with point defect chemistry models. Measurements at very low p_O2 showed several phase transitions.     

Influence of oxygen growth pressure on laser ablated Cr-doped In2O3 thin films

We present a systematic investigation of the effects of oxygen growth pressure on the structural, optical, and electrical properties of In₂O₃:Cr thin films grown by pulsed laser deposition. X-ray diffraction analysis showed increases in lattice constant from 10.103 Å to 10.337 Å, and in particle size from 13.9 nm to 35.5 nm as the oxygen growth pressure increased from 7.5 × 10⁻⁶ Torr to 7.5 × 10⁻³ Torr, respectively. The observed shift in the X-ray diffraction peaks to lower angles was assumed to be caused by the reduction in the lattice defect density, precisely oxygen vacancies. The optical transparency increased with partial oxygen pressure (P_O2), and an average transmittance of 85% was obtained at 7.5 × 10⁻³ Torr. The films are highly conducting with resistivity as low as 2 × 10⁻⁴ Ω cm and mobility as high as 133 cm/V s. Temperature dependent resistivity measurements in the 45 < T < 300 K temperature range reveal that films grown at 7.5×10⁻⁶≤P_O2≤7.5×10⁻⁴ Torr exhibit negative temperature coefficient of resistivity (TCR) below approximately T = 60 K, T = 120 K, T = 160 K; then positive TCR in the temperature intervals 60 < T < 300 K, 120 < T < 300 K, and 160 < T < 300 K, respectively. This suggests that two disparate mechanisms govern electrical dc transport in the two temperature regions. Film grown at P_O2 of 7.5 × 10⁻³ Torr displayed typical semiconducting behavior with negative TCR in the whole temperature region.     

Electrical and mechanical properties of proton conducting SrCe0.95Yb0.05O3 − α

Yb³⁺-doped ceramic strontium cerate of exactly the composition SrCe_0.95Yb_0.05O_{3 − α} was prepared, having a relative density of 99.0 (± 0.3%). Great care was taken to obtain homogeneous, carbonate free material. Analysis are made of the X-ray powder diffraction pattern of the as-prepared dense ceramic, resulting in the orthorhombic unit cell parameters a = 6.997(2) Å, b = 12.296(3) Å, c = 8.588(2) Å, Z = 8 and d_x = 5.806(2) g cm⁻³. Bending strength values of the ceramic in non-proton and proton conducting state are found to be 177 and 194 MPa respectively. The ceramic kept under proton conducting conditions for 500 h at 300 °C to 800 °C in a N₂ flow containing 155 mbar water vapour and 245 mbar H₂, have shown to remain chemically and structurally stable. Impedance spectroscopy measurements of the bulk conductivity of the proton conducting ceramic revealed an activation energy of 53.2 kJ mol⁻¹ and a preexponential factor of 359.1 (Ω cm)⁻¹ K. In the non-proton conducting state the ceramic is mainly oxygen ion vacancy conducting, which indicates that charge compensation on substituting Yb⁺³ in SrCeO₃ takes place by oxygen ion vacancies.     

Oxygen nonstoichiometry of Sr(Co,Fe)O3−δ-based perovskites: I. Coulometric titration of SrCo0.85Fe0.10Cr0.05O3−δ by the two-electrode technique

The p(O₂)–T–δ diagram of perovskite-type SrCo_0.85Fe_0.10Cr_0.05O_3−δ was determined by the coulometric titration technique in the temperature range 770–1250 K at oxygen partial pressures from 8 10⁻¹⁰ to 0.5 atm. Stability of the cubic perovskite phase of SrCo_0.85Fe_0.10Cr_0.05O_3−δ, existing down to the oxygen pressures of 10⁻³–10⁻⁵ atm, was found to be slightly higher than that of SrCo_0.80Fe_0.20O_3−δ, probably due to stabilization of oxygen octahedra neighboring Cr⁴⁺ cations. When the oxygen nonstoichiometry of the Cr-containing perovskite decreases from 0.47 to 0.38, the partial molar enthalpy and entropy for overall oxygen incorporation reaction vary in the ranges −165 to −60 kJ mol⁻¹ and 90 to 150 J mol⁻¹ K⁻¹, respectively. Within the stability limits of the single perovskite phase, the p(O₂)–T–δ diagram can be adequately described by equilibrium processes of oxygen incorporation, cobalt disproportionation and interaction of cobalt and iron cations, with the thermodynamic functions independent of defect concentrations. Increasing grain size in SrCo_0.85Fe_0.10Cr_0.05O_3−δ ceramics from submicron size to 100–200 μm has no effect on the oxygen thermodynamics. The two-electrode coulometric titration technique, based on the alternate use of electrodes for oxygen pumping and e.m.f. measurements, is described and verified by studying oxygen nonstoichiometry of La_0.3Sr_0.7CoO_3−δ and PrO_x.     

Magnetic and magnetotransport properties of Co-doped manganites with perovskite structure

A systematic study of the doping of the Mn-sites by cobalt in three series of manganites — La_0.76Ba_0.24(Mn_1−xCo_x)O₃ single crystals, La_2/3Ba_1/3(Mn_1−xCo_x)O₃ and La(Mn_1−xCo_x)O₃ ceramics has been performed. It was found that La(Mn_1−xCo_x)O₃ annealed at 800°C in the range 0.4x0.9 is a mixture of ferromagnetic domains with ordered Mn and Co ions and ionically disordered spin-glass domains. In the quenched samples the fraction of spin-glass-type component increases strongly. The La_2/3Ba_1/3(Mn_1−xCo_x)O₃ solid solutions exhibit also an evidence for phase separation in the range 0.5x0.8. All the La(Mn_1−xCo_x)O₃ samples show an insulating behavior, however, magnetoresistance reduces strongly when the cobalt content rises to x=0.5. The La_0.76Ba_0.24(Mn_1−xCo_x)O₃ single crystals show first-order phase transition below their Curie points associated with a change of ground state of the Co²⁺ ions. The magnetic phase diagrams are depicted. The results are discussed in terms of positive Mn³⁺–O–Mn⁴⁺, Mn³⁺–O–Mn³⁺, Mn⁴⁺–O–Co²⁺ and negative Mn⁴⁺–O–Mn⁴⁺, Co²⁺–O–Co²⁺, Co²⁺–O–Mn³⁺ superexchange interactions as well as Co²⁺ and Mn⁴⁺ ionic ordering.     

Magnetic properties of FexCo1−x/CoyFe1−yFe2O4 composite under hydrothermal condition

The metal–ferrite composites Fe_xCo_1−x/Co_yFe_1−yFe₂O₄ are synthesized by using disproportion of Fe (II) and reduction of Co (II) by Fe⁰ under hydrothermal condition. The size of the particles of the composites decreases as the [KOH] decreasing. The composites are measured by TEM and it can be deduced that when [KOH] = 0.1, the size of the alloy body-centered cubic (BCC) in composites is 20 ± 7 nm, the size of the Cobalt ferrite (spinel) is 170 ± 50 nm. The maximal value of the saturation magnetization (Ms) of the composite is about 100.14 emu/g, which is synthesized under Co (II)/Fe (II) = 0.05, [KOH] = 1 N, T = 150 °C and t = 3 h. The value of Hc of the composite synthesized under Co (II)/Fe (II) = 0.5, t = 3 h, T = 150 °C and [KOH] = 10.2 mol/L is about 2878.19 Oe. The Fe–Co alloy is synthesized through a reduction reaction of the composites in a flowing gaseous mixture. There is a maximal value (302.9 emu/g) of the Ms for the alloys generated at 1000 °C, which is the Co_0.412Fe_0.588 alloy.     

Kerr property of cubic K0.95Li0.05Ta0.60Nb0.40O3 single crystal

The Kerr (quadratic electro-optic) property of K_0.95Li_0.05Ta_0.60Nb_0.40O₃ was measured by using an automated scanning Mach–Zehnder interferometer. K_0.95Li_0.05Ta_0.60Nb_0.40O₃ has large Kerr effect with R₁₁ = 7.2 × 10⁻¹⁶ m²/V² and R₁₂ = −1.2 × 10⁻¹⁶ m²/V² at 632.8 nm near its phase-transition temperature. The dielectric and Kerr properties as function of temperature were also investigated, thus the quadratic polarization-optic coefficients were calculated. The values of g₁₁ and g₁₂ are 0.083 m⁴/C² and −0.014 m⁴/C², respectively, and do not depend on temperature within the measurement accuracy of 5%.     

High-resolution infrared study of the 2ν3 (A1, E) and ν1 + ν3 (E) bands of NF3

The 2ν₃ overtone (A₁, E) and the ν₁ + ν₃ (E) combination bands of the oblate symmetric top ¹⁴NF₃ were studied by FTIR spectroscopy with a resolution of 2.5 × 10⁻³ cm⁻¹. Nearly 500 lines up to K_max/J_max = 30/43 were observed for the weak A₁ component reaching the v₃ = 2⁰ substate (1803.1302 cm⁻¹), the majority of which corresponded to reinforced K = 3p-type transitions. For the strong E component reaching the v₃ = 2^±2 substate (1810.4239 cm⁻¹), about 3550 transitions were assigned up to K_max/J_max = 65/69, favoring a clear observation of the ℓ(4, −2) and ℓ(4, 4) splittings within the kℓ = −2 and +4 sublevels, respectively. The two v₃ = 2 substates are linked by the ℓ(2, 2)- and ℓ(2, −1)-type interactions, providing severe crossings, respectively, at K′ = 6 and near K′ = 24 on the v₃ = 2⁺² side. A model working in the D-reduction and including all these ℓ-type interactions could reproduce together 3695 nonzero weighted experimental data (NZW) through 33 free parameters with a standard deviation of σ = 0.357 × 10⁻³  cm⁻¹. As for the ν₁ + ν₃ (E) combination band, about 3690 lines were assigned up to K_max/J_max = 45/55. Its v₁ = v₃ = 1 upper state (1931.577 5 cm⁻¹) was treated using the same model recently applied to the v₃ = 1 (E, 907.5413 cm⁻¹) state. It yielded 21 free parameters through 3282 NZW experimental data, adjusted with σ = 0.344 × 10⁻³  cm⁻¹ in the D-reduction. For the two excited states, the small and unobserved ℓ(0, 6) interaction was tested as useless. To confirm the adequacy of the vibrationally isolated models used, some other reductions of the Hamiltonian were tried. For the v₃ = 2 state, the D-, L-, and LD-reductions led to similar σ’s, while the Q one was not successful. For the v₁ = v₃ = 1 state, the D- and Q-reductions gave comparable σ’s, while the QD-reduction was not as good. The corresponding unitary equivalence relations are generally more nicely fulfilled for the v₃ = 2 state than for the v₁ = v₃ = 1 state. The three derivable anharmonicity constants in cm⁻¹ are x₃₃ = −4.1528, g₃₃ = +1.8235 and x₁₃ = −7.9652.     

Influence of octahedral tilting and composition on electrical properties of the Li0.2 − xNaxLa0.6TiO3 (0 ≤ x ≤ 0.2) series

The Rietveld analysis of ND patterns of polycrystalline Li_0.2 − xNa_xLa_0.6TiO₃ (0 ≤ x < 0.2) samples, recorded between 300 and 1075 K, shows an orthorhombic–tetragonal transformation, in which the octahedral tilting along the b axis is eliminated at ~ 773 K, but the vacancy ordering along the c axis remains. In Li rich samples, conductivity (10^− 3 Ω^− 1 cm^− 1 at 300 K) departs from the Arrhenius behaviour, decreasing activation energies from 0.37 to 0.14 eV when octahedral tilting is eliminated. Successive Maxwell–Wagner blocking processes, detected in the real part of dielectric constant plots, have been ascribed to the Li blocking at interior domains, grain-boundary and electrode–electrolyte interfaces. The substitution of Li⁺ by Na⁺ decreases the amount of vacant A-sites, decreasing several orders of magnitude the conductivity when the amount of vacancies approaches the vacancy percolation threshold (n_p = 0.27). Below the percolation threshold, Li ions only display local mobility, remaining confined into small domains of perovskites.     

Synthesis, characterization and melt processing of Y1−x(Yb0.9Nd0.1)xBa2Cu3Oz superconductors

Effects of a combined substitute of Yb and Nd on Y site on the superconducting properties of YBa₂Cu₃O_y have been studied. We synthesized Y_1−x(Yb_0.9Nd_0.1)_xBa₂Cu₃O_z compound with x = 0.2, 0.4, 0.6, 0.8 and 1.0. Here, the ratio of Yb–Nd was fixed to be 9:1 for obtaining 123 phase without secondary phases. The melt processing thermal profiles for Y_1−x(Yb_0.9Nd_0.1)_xBa₂Cu₃O_z with x = 0.2 and 0.4 and the addition of 40 mol% {Y_1−x(Yb_0.9Nd_0.1)_x}₂BaCuO₅ and 0.5 wt% Pt in air were determined on the basis of the thermal analysis results. All samples showed a low grain growth rate, particularly for high x values, which may be partially ascribed to un-optimized thermal schedules. Although almost all the samples exhibited low J_c values, the sample with x = 0.2 exhibited T_c of 88.8 K and a relatively high J_c value of 16,000 A/cm² at 77 K for H//c-axis.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

Annealing effect on the superconductivity of In2O3–ZnO thin films

We have investigated the relation among ρ–T characteristics, superconductivity, annealing conditions and the crystallinity of polycrystalline (In₂O₃)_1−x–(ZnO)_x films. We annealed as-grown amorphous films in air by changing annealing temperature and time. It is found that the films annealed at 200 °C or 300 °C for a time over 0.5 h shows the superconductivity. Transition temperature T_c and the carrier density n are T_c < 3.3 K and n ≈ 10²⁵–10²⁶ m⁻³, respectively. Investigations for films with x = 0.01 annealed at 200 °C have revealed that the T_c, n and crystallinity depend systematically on annealing time. Further, we consider that there is a suitable annealing time for sharp resistive transition because the transition width becomes wider with longer annealing times. We studied the upper critical magnetic field H_c2(T) for the film with different annealing time. From the slope of dH_c2/dT for all films, we have obtained the resistivity ρ dependence of the coherence length ξ(0) at T = 0 K.     

Fe3O4(111) termination of α-Fe2O3(0001)

Scanning tunnelling microscopy (STM) has been used to investigate the structure formed on an α-Fe₂O₃(0001) substrate after argon ion bombardment and annealing in 1 × 10⁻⁶ mbar of O₂ at 1000 K. The STM images recorded at positive sample bias reveal an hexagonal array, with a distance between (Fe) atoms of 6.0 ± 0.1 rA and steps in multiples of 4.8 Å. These results are consistent with formation of an Fe₃O₄(111) epitaxial layer terminating in a monolayer of Fe atoms.     

Dependence of property, crystal structure and electric conductivity on substitution content and synthetic process of T′-La2−xRExCuO4−δ (RE = Sm and Tb)

We synthesized T′-La_2−xRE_xCuO_4−δ (RE = Sm and Tb) by a co-precipitation method and sintering in vacuum at various temperatures, and investigated relationship among the crystal structure, average valence of Cu, oxygen content and electric conductivity. From X-ray diffraction measurements, it was confirmed that a main phase of the product was T′ structure (S. G.: I4/mmm) regardless of the rare earth element and its concentration, although an impurity phase was observed in a part of samples. In the samples with low average valence of Cu, the resistivity showed a metallic behavior and remarkably decreased at low temperature. Rietveld analyses using synchrotron X-ray diffractions suggested that the electric conductivity was improved by decreasing a bond length of Cu–O1 in the case of La_2−xSm_xCuO_4−δ.     

Water incorporation into the Ba2(In1 − xMx)2O5‪ (M = Sc 0 ≤ x < 0.5 and M = Y 0 ≤ x < 0.35) system and protonic conduction

Ba₂(In_1 − xM_x)₂O_{5 − y / 2}(OH)_y‪□_{1 − y / 2} (y ≤ 2; M = Sc³⁺ 0 ≤ x < 0.5 and M = Y³⁺ 0 ≤ x < 0.35) compounds were prepared by reacting Ba₂(In_1 − xM_x)₂O₅‪ phases with water vapor. This reaction is reversible. Analyses of the hydration process by TG and XRD studies show that the thermal stability of hydrated phases increases when x increases and that the incorporation of water is not a single-phase reaction inducing either a crystal system or space group modification. Fully hydrated (y = 2) and dehydrated (y = 0) samples have been stabilized at room temperature and characterized for all compositions. In wet air, all phases show a proton contribution to the total conductivity at temperatures between 350 and 600 °C. At a given temperature, proton conductivity increases with the substitution ratio and reaches at 350 °C, 5.4 10^− 3 S cm^− 1 for Ba₂(In_0.65Sc_0.35)₂O_4.2□_0.2(OH)_1.6.     

Structure, ferroelectric and piezoelectric properties of (Bi1−x−yNa0.925−x−yLi0.075)0.5BaxSryTiO3 lead-free piezoelectric ceramics

Lead-free multi-component ceramics (Bi_1−x−yNa_{0.925−x−y}Li_0.075)_0.5Ba_xSr_yTiO₃ have been prepared by an ordinary sintering technique and their structure and electrical properties have been studied. All the ceramics can be well-sintered at 1100 °C. X-ray diffraction patterns shows that Li⁺, Ba²⁺ and Sr²⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a new solid solution with a pure perovskite structure, and a morphotropic phase boundary (MPB) is formed at 0.04 < x < 0.08. As compared to pure Bi_0.5Na_0.5TiO₃ ceramic, the coercive field E_C of the ceramics decreases greatly and the remanent polarization P_r of the ceramics increases significantly after the formation of the multi-component solid solution. Due to the MPB, lower E_C and higher P_r, the piezoelectricity of the ceramics is greatly improved. For the ceramics with the compositions near the MPB (x = 0.04–0.08 and y = 0.02–0.04), piezoelectric coefficient d₃₃ = 133–193 pC/N and planar electromechanical coupling factor k_P = 16.2–32.1%. The depolarization temperature T_d reaches a minimum value near the MPB. The temperature dependences of the ferroelectric and dielectric properties suggest that the ceramics may contain both the polar and non-polar regions at temperatures near/above T_d.     

Study of the interaction of Na9[SbW9O33]·19.5H2O with bovine serum albumin: Spectroscopic and voltammetric methods

The interaction of Na₉[SbW₉O₃₃]·19.5H₂O (SbW) with bovine serum albumin (BSA) is studied by spectroscopic and voltammetric methods. Absorption spectroscopy of BSA and the linear sweep voltammetry of SbW proved the formation of ground-state SbW–BSA complex. Fluorescence quenching of serum albumin by SbW is also found to be a static quenching process. The binding constant K_a is 4.13×10⁴ L mol⁻¹ for SbW–BSA at pH 7.40 Tris–HCl buffer at 295 K. The number of binding sites and the apparent binding constants at different temperatures are obtained from the analysis of the fluorescence quenching data. The thermodynamic parameters determined by the Van’t Hoff analysis of the binding constants (ΔH=−80.01 kJ mol⁻¹ and ΔS=−182.85 J mol⁻¹ K⁻¹) clearly show that the binding is absolutely entropy driven. Hydrogen bonding and van der Waals interaction force play major role in stabilizing the complex. The effect of SbW on the conformation of BSA is analyzed using synchronous fluorescence spectroscopy.     

High-resolution infrared and millimeterwave spectra of the v3=1 vibrational state of NF3 at 907 cm

The ν₃^±1 perpendicular band of ¹⁴NF₃ ( cm⁻¹) has been studied with a resolution of 2.5 × 10⁻³ cm⁻¹, and 3682 infrared (IR) transitions (J_max=55, K_max=45) have been assigned. These transitions were complemented by 183 millimeterwave (MMW) rotational lines (J_max=25, K_max=19) in the 150–550 GHz region (precision 50–100 kHz). The kl=+1 level reveals a strong A₁/A₂ splitting due to the l(2,2) rotational interaction (q=−4.05 × 10⁻³ cm⁻¹) while the kl=−2 and +4 levels exhibit small A₁/A₂ splittings due to l(2,−4) and l(0,6) rotational interactions. All these splittings were observed by both experimental methods. Assuming the v₃=1 vibrational state as isolated, a Hamiltonian model of interactions in the D reduction, with l(2,−1) rotational interaction (r=−1.96 × 10⁻⁴ cm⁻¹) added, accounted for the observations. A set of 26 molecular constants reproduced the IR observations with σ_IR=0.175 × 10⁻³ cm⁻¹ and the MMW data with σ_MMW=134 kHz. The Q reduction was also performed and found of comparable quality while the QD reduction behaved poorly. This may be explained by a predicted Coriolis interaction between v₃=1 and v₁=1 (A₁, 1032.001 cm⁻¹) which induces a slow convergence of the Hamiltonian in the QD reduction but has no major influence on the other reductions. The experimental equilibrium structure could be calculated as: r_e(N–F)=1.3676 Å and (FNF)=101.84°.     

Growth of superconducting single-crystalline (Lu, Ca) Ba2Cu3O7−δ whiskers

Single-crystalline (Lu, Ca)Ba₂Cu₃O_7−δ (Lu(Ca)123) whiskers have been successfully grown using the Te-doping method. X-ray diffraction patterns of Lu(Ca)123 whiskers showed sharp (0 0 l) peaks corresponding to REBa₂Cu₃O_7−δ phase (RE = rare earth elements). Transport measurements showed that the superconducting transition occurred at 83 K in the obtained whiskers.     

High resolution FTIR spectroscopy of pentafluoroethane: perturbations in the Coriolis doublet of ν4 and ν13

The FTIR spectrum of pentafluoroethane (R125) was measured in the mid infrared region from 900 to 4000 cm⁻¹. Vibrational assignments for R125 are revised by comparison of previous and current experimental data with ab initio calculations at both the MP2/6-311+(d,p) and B3LYP/TZV+(3df,3p) levels of theory. High resolution FTIR spectra were recorded at room temperature and in an enclosive flow cell at a rotational temperature of 140 K. The cold spectrum was sufficiently resolved to enable rovibrational analyses of the overlapping ν₄ (1200.7341 cm⁻¹) and ν₁₃ (1223.3 cm⁻¹) bands, which have a/c hybrid and b-type character, respectively. Ground state combination differences were used to confirm assignment of 2375 lines to ν₄ (J_max = 86, K_{a max} = 50) and 2921 lines to ν₁₃ (J_max = 60, K_{a max} = 54). Effective rotational and centrifugal distortion constants were determined for ν₄, and the polarization ratio was found to be . Severe Coriolis perturbations prevent any satisfactory fit to the ν₁₃ band.