High-Resolution Solid-State NMR Characterization of Morphology in Annealed Polylactic Acid

Single-pulse ¹³C NMR spectra and spin-lattice relaxation times T₁(¹H), detected indirectly via ¹³C carbons, and T₁(¹³C) were measured at 31°C for virgin pelletized and annealed polylactic acid (PLA) samples using the magic-angle spinning technique. The structural relaxation resulting in more regular crystals with narrower conformation distribution and increase in the lamellae thickness and crystallinity brought about by annealing at 100°C was deduced from the narrowing of the ¹³C NMR lines and proton spin-lattice relaxation times T₁(¹H). The spin-lattice relaxation times T₁(¹³C) related to the respective carbons of the α-polymorph of PLA are also discussed in the study.     

New solid polymer electrolytes based on polyester diacrylate for lithium power sources

New solid polymer electrolytes are developed for a lithium power source used at the temperatures up to 100°C. Polyester diacrylate (PEDA) based on oligohydroxyethylacrylate and its block copolymers with polyethylene glycol were offered for polymer matrix formation. The salt used was LiClO₄. The ionic conductivity of electrolytes was measured in the range of 20 to 100°C using the electrochemical impedance method. It is shown that the maximum conductivity in the whole temperature range is characteristic of the electrolyte based on the PEDA copolymer and polyethylene glycol condensation product (2.8 × 10^?6 S cm^?1 at 20°C, 1.8 × 10^?4 S cm^?1 at 95°C).     

Sol-Gel Processing of Sm2+-Doped Glass and Its Spectral Hole Burning at Room Temperature

The sol-gel process was applied to the preparation of Sm²⁺ ion-doped silicate glasses, which show persistent spectral hole burning at room temperature. The gels synthesized by the hydrolysis of metal alkoxides and SmCl₃·6H₂O were heated in air at 500°C, were then reacted with H₂ gas to form the Sm²⁺ ion. The Al₂O₃−SiO₂2 glasses are appropriate to reduce the Sm³⁺ ion with H₂ gas and show intense photoluminescence of Sm²⁺ ion. Persistent spectra hole burning was observed in the excitation spectrum for the⁷F₀→⁵D₀ transition of the Sm²⁺ ion by the irradiation of DCM dye laser. The hole width and depth were ∼16 cm⁻¹ and ∼10% of the total intensity, respectively, at 20°C.     

27Al NMR Study of Al-Speciation in Aqueous Alumina-Sols

A new method of preparing concentrated alumo-sols, the hydrolysis of Al-tri-sec-butylate in acidic aqueous media at 85°C, was studied in detail by varying the H₂O/Al- and NO₃ ⁻/Al-ratios in wide ranges. The components of the sols were characterized by ²⁷Al NMR spectroscopy. The pH-value depends on both the chosen H₂O/Al- and NO₃ ⁻/Al-ratio and on the aging time of the sols and reflects the composition of the sols. Al₁₃ polycations were detected in sols with a pH-value between 3.0 and 3.7. As a new result its presence was shown by NMR below 3.4. The Al₁₃ content of the sols increased with pH and the maximum fraction of Al₁₃ polycations was detected in the sol with the highest pH (3.7). Nearly 65% of the entire aluminium content of this solution is bound in the Al₁₃ polycations. Hence, a new synthetic method for the preparation of Al₁₃ ions containing sols was developed. Aging studies of the sols showed, that the Al₁₃ polycations were more stable in solutions with higher pH-value. Al₁₃ polycations were detected after an aging time of four months only in sols with a pH-value of 3.7. Tempering the aged sols at 40° to 80°C caused formation of Al₁₃ and also of Al₃₀ polycations.     

Eu,Dy co-doped SrAl<Subscript>2</Subscript>O<Subscript>4</Subscript> phosphors prepared by sol–gel-combustion processing

SrAl₂O₄:Eu²⁺, Dy³⁺ powders were synthesized by sol–gel–combustion process using metal nitrates as the source of metal ions and citric acid as a chelating agent of metal ions. The amounts of citric acid in mole were two times those of the metal ions. By tracing the formation process of the sol–gel, it is found that decreasing the amount of NO₃ ⁻ in the solution is necessary for the formation of transparent sol and gel, and the dropping of ethanol into the precursor solution can decrease the amount of NO₃ ⁻ in the solution. By combusting citrate sol at 600 °C, followed by heating the resultant combustion ash at 1,100–1,300 °C in a weak reductive atmosphere containing active carbon, SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors can prepared. X-ray diffraction, Thermogravimetry–differential thermal analysis, scanning electron microscopy and fluorescence spectrophotometer were used to investigate the formation process and luminescent properties of the as-synthesized SrAl₂O₄:Eu²⁺, Dy³⁺. The results reveal that the SrAl₂O₄ crystallizes completely when the combustion ash was sintered at 1,200–1,300 °C. The excitation and emission spectra indicate that excitation broadband mainly lies in a visible range and the phosphors emit strong light at 510 nm under the excitation of 348 nm. The afterglow of phosphors lasts for over 10 h when the excited source is cut off.     

PREPARATION AND SPECTRAL PROPERTIES OF SYMMETRICAL S-ARYL ARENESULFONOTHIOATES (THIOSULFONATES)

Abstract

Arenesulfinyl chlorides (4-XC₆H₄S(O)Cl); × = H, CH₃, F, Cl, Br) react with activated zerovalent zinc in benzene at 6 to 8°C to give symmetrical S-aryl arenesulfonothioates (thiosulfonates) in good to excellent yields. 2-and 3-Substituted arenesulfinyl chlorides (X = Cl, CH₃) give a mixture of products (disulfide, thiosulfinate, and/or thiosulfonate). 2,4,6-Triisopropylbenzenesulfinyl chloride reacts with zinc in 1,2-dimethoxyethane to give S-(2,4,6-triisopropylphenyl) 2,4,6-triisopropylbenzenesulfinothioate and bis(2,4,6-triisopropylphenyl) disulfide. Possible mechanisms for the reactions, the ¹H and ¹³C NMR spectra, and the chemical ionization and electron impact mass spectra of the thiosulfonates are discussed. The para carbon substituent chemical shifts (C_p-SCS) for the thiosulfonates and for symmetrical diaryl disulfides have been subjected to several dual substituent parameter (DSP) correlations.     

Formation of borosilicate glasses from silicon alkoxides and metaborate esters in dry non-aqueous solvents

The reaction of metaborate esters (RO)₃B₃O₃ [R = Me, Et, ClCH₂CH₂–, Cl₃CCH₂–, ClCH₂CH₂CH₂–, (ClCH₂)₂CH–] with Si(OR)₄ (R = Me, Et), either neat or in dry propan-2-one or dry THF at room temperature, led to gels which when dried and heated in air for 20 mins at 600°C afforded borosilicate glasses in high ceramic yields. The dried gels and glasses were characterized by elemental analysis, TGA, IR, and powder XRD, and solid-state MAS ²⁹Si and ¹¹B NMR. The gelling reaction was investigated by solution ¹¹B and ²⁹Si NMR. These NMR studies indicated B–O–Si reaction intermediates and a mechanism involving alkoxy exchange and various condensation/elimination reactions of the borosilicate esters have been proposed.     

Critical phenomena in ethylbenzene oxidation in acetic acid solution at high cobalt(<Emphasis Type="SmallCaps">II</Emphasis>) concentrations

Critical phenomena in ethylbenzene oxidation in an acetic acid solution at high cobalt(III) concentrations (from 0.01 to 0.2 mol L⁻¹) were studied at 60–90 °C by the gasometric (O₂ absorption), spectrophotometric (Co^III accumulation), and chemiluminescence (relative concentration of radical RO₂ ^·) methods. These phenomena are as follows: (1) increase in the oxidation rate above the theoretical limiting rate of radical autooxidation (k ₃ ²[RH]²/2k ₆); (2) achievement of a maximum and a sharp decrease in the oxidation rate and concentration of radical RO₂ ^· with the further increase in the Co^II concentration (existence of critical concentrations). The oxidation rate increases due to the reaction RO₂ ^· + Co^II + H⁺ → → ROOH + Co^III, while the inhibition effect is caused by the decay of RO₂ ^· radical involving two cobalt(II) atoms: RO₂ ^· + 2 Co^II → R′CO + Co^III + Co^II (k(70 °C) ≈ 300 L² mol⁻² s⁻¹). The detailed scheme (through the formation of the complex RO₂ ^·Co^II) describing the conjugation of these reactions was proposed. __________ Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1823–1827, August, 2005.     

Copolymerization of 4‐Propanoylphenyl Acrylate with Methyl Methacrylate: Synthesis,Characterization and Reactivity Ratios

The new acrylic monomer 4‐propanoylphenyl acrylate (PPA) was synthesized and copolymerized with methyl methacrylate (MMA) in methyl ethyl ketone at 70±1°C using benzoyl peroxide as a free radical initiator. The copolymers were characterized by FT‐IR, ¹H‐NMR and ¹³C‐NMR spectroscopic techniques. The compositions of the copolymers were determined by ¹H‐NMR analysis. The reactivity ratios of the monomers were determined using Fineman‐Ross (r₁=0.5535 and r₂=1.5428), Kelen‐Tüdös (r₁=0.5307 and r₂=1.4482), and Ext. Kelen‐Tüdös (r₁=0.5044 and r₂=1.4614), as well as by a nonlinear error‐in‐variables model (EVM) method using a computer program, RREVM (r₁=0.5314 and r₂=1.4530). The solubility of the polymers was tested in various polar and non‐polar solvents. The elemental analysis was determined by a Perkin‐Elmer C‐H analyzer. The molecular weights (M_w and M_n) of the copolymers were determined by gel permeation chromatography. Thermogravimetric analysis of the polymers reveals that the thermal stability of the copolymers increases with an increase in the mole fraction of MMA in the copolymers. Glass transition temperatures of the copolymers were found to increase with an increase in the mole fraction of MMA in the copolymers.     

Polymerization of N,N-Dimethylaminopropyl-Acrylamide Through Hydrogen Transfer Induced by the Propagation of the Polyacrolein Anion

The anionic polymerization of acrolein (AL) with N, N-dimethylamino-propylacrylamide (DMAPA) in the presence of water was investigated in tetrahydrofuran, benzene, and ethanol at 0°C in a nitrogen atmosphere. The resulting polymers were found to be essentially vinyl polymers with one DMAPA attached and an aldehyde side chain. From observations of the polymerization process by ¹H NMR, we find that polymerization was initiated by the hydroxyl anion formed in the thermodynamic equilibrium between the amine of DMAPA and water. The hydrogen transfer reaction of DMAPA was caused by the propagating poly-AL anion. On the other hand, the monomer reactivity ratios and the Q₂-e₂values of DMAPA were determined by the free-radical copolymerization of styrene (St, M₁) with DMAPA and AIBN as initiator.     

Electrochemical properties of systems with rubidium-tungsten-oxide bronze

Single-phase rubidium-tungsten-oxide bronze of the composition Rb_0.3WO₃ with hexagonal syngony (a = 0.7387 ± 0.0004 nm, c = 0.7547 ± 0.0004 nm) is synthesized. The ionic constituent of the bronze conductivity, determined for the first time ever, is nearly three orders of magnitude as small as the electronic constituent and varies from 1.1 × 10^?2 to 2.7 × 10^?2 S cm^?1 at 30–84°C. The reversibility of the Rb_0.3WO₃/Rb₆La₂Si₆O₁₈ interface increases with the environment humidity. The exchange current is equal to 6.4 × 10^?4 A cm^?2 at a temperature of 30°C and a relative humidity of 58%. It is shown that the synthesized bronze may, in principle, be utilized in the role of a reference electrode in solid-state potentiometric sensors for carbon dioxide and hydrogen sulfide that would be capable of operating in natural conditions.     

Short Range Order Evolution in the Preparation of SnO2 Based Materials

The evolution of Eu³⁺ doped SnO₂ xerogels to the cassiterite structure observed during sintering was studied by means of Eu³⁺ spectroscopy, XRD and EXAFS at the Sn K-edge. Eu³⁺ ions adsorbed at the surface of colloidal particles present a broad distribution of sites, typical of oxide glasses. With sintering at 300°C, this distribution is still broadened. Crystallization is clearly observed by the three techniques with increasing sintering temperature. It is found that the addition of Eu³⁺ limits the crystallite growth.     

Properties and Extraction for [Ni(NH3)6]2+ of ATPS-a Formed by Aqueous Cationic–Anionic Surfactant Mixtures

The properties and extraction for [Ni(NH₃)₆]²⁺ of anionic aqueous two-phase systems (ATPS-a) that formed in mixtures of cetyltrimethylammonium bromide (CTAB) and excess sodium dodecyl sulfate (SDS) aqueous solutions were investigated. The results showed that the properties and extraction effects were strongly affected by the surfactant concentration, the temperature of system, and the mole fraction of surfactants. The increase of temperature induces narrower phase region and larger phase volume ratio. In addition, [Ni(NH₃)₆]²⁺ was extracted into the surfactant-rich phase with higher distribution coefficient when the liquid crystal had the birefringent properties. Moreover, the distribution coefficient can be improved through reducing the concentration of surfactant from 0.15 to 0.05 mol · L^?1 or increasing mole fraction of CTAB from 21.9% to 23.1%. The results showed that ATPS of cationic–anionic surfactants was efficient for [Ni(NH₃)₆]²⁺ extraction with distribution coefficients of 13.5 when the total surfactant concentration was 0.05 mol · L^?1, mole fraction of CTAB was 21%, and temperature was 34°C.     

MACROBICYCLIC D-METAL TRIS-DIOXIMATES OBTAINED BY CROSS-LINKING WITH P-BLOCK ELEMENTS. PART VI. PREPARATION,MOLECULAR STRUCTURE AND MÖSSBAUER (57FE, 119SN) PARAMETERS OF AN IRON(II) COMPLEX WITH A MACROBICYCLIC TIN-CONTAINING TRIS-NIOXIMATE LIGAND

Abstract

The tin-containing clathrochelate complex of Fe(II) with cyclohexanedione-1,2-dioxime (nioxime, H₂Nx), [FeNx₃(SnCl₃)₂]^2- · (Et₂NH⁺ ₂)₂ · Et₂NH₂ ⁺ · Cl^? · 2Prⁱ OH was prepared by slowly adding diethylamine to a solution containing the macrobicyclic [FeNx₃(SnCl₃)₂]^2- anion. The structure of the complex has been determined by X-ray methods. Crystal data: monoclinic, space group P2₁/c, a = 10.565(2), b = 25.413(5), c = 20.198(4)Å, β=95.40(3)°, Z = 4. The iron atoms is encapsulated by the clathrochelate ligand and surrounded by a distorted trigonal antiprismatic coordination sphere comprising by six nitrogen atoms of three dioxime residues. The experimental value of the distortion angle (ca 37.5°) is close to that predicted by the Mössbauer (⁵⁷Fe) parameters (ca 40°). The average Fe-N bond length of 1.923Å is somewhat greater than that in boron-containing analogues. The Sn atoms have a slightly distorted octahedral coordination, which also correspond to Mössbauer (¹¹⁹Sn) spectroscopic data. The six-membered carbocycles in the dioxime fragments have a half-chair conformation with both β-carbons displaced to the opposite sides of the mid-plane of the remaining atoms. All the active hydrogen atoms of the structure are involved in a hydrogen bond system.

The possibilities of use of Mössbauer parameters and their temperature dependences to determine the geometry of iron(II) tris-dioximates and the sign of Δ in Mössbauer (⁵⁷Fe) spectra are discussed.     

Synthesis and characterization of functionalized amphiphilic polymers for utilization as surfactants

Eight novel PEG-based amphiphilic block copolymers having self-assembling properties has been reported in the present study. The polymers have been synthesized by reacting Poly(ethylene glycols) (PEGs) of different molecular weights viz. 600, 1000, 1500 and 2000 and dimethyl-5-hydroxyisophthalate in presence of concentrated H₂SO₄ as catalyst in solventless condition at 80–90°C and further alkylating the resulting polymers by attaching octyl and hexadecanyl chains to phenolic hydroxyl group. The resulting functionalized amphiphilic polymers have been characterized by ¹H and ¹³C-NMR spectroscopy. These polymers, when dissolved in water, aggregate to form micelles, giving sizes ranging from 13.00 to 87.24 nm as determined by Dynamic Light Scattering (DLS) instrument. The molecular weights have been also calculated from the DLS and are in the range 3.5×10⁴ to 1.8×10⁶ KDa (Kilo Daltons). Critical Micelle Concentrations (CMC) of the synthesized polymers was determined using electrical conductivity meter with values in the range of 105 to 138 mg L^?1 (milligrams per litre).     

Complex Formation of 1,10-Dibenzyl-1,10-diaza-18-crown-6 with Ni2+, Cu2+, Ag+ and Cd2+ Metal Cations in Acetonitrile–dimethylformamide Binary Solutions

Conductance measurements are reported for nickel(II), cupper(II), silver(I) and cadmium(II), salts in acetonitrile (AN)–dimethylformamide (DMF) binary solvents containing macrocyclic ligand, 1,10-dibenzyl-1,10-diaza-18-crown-6 (DBDA18C6) at different temperatures. The changes in molar conductance caused by addition of DBDA18C6 to solutions were analyzed by non-linear least squares to give stability constants of 1:1 metal cation–DBDA18C6 complexes. The results show that the stabilities of the complexes are sensitive to solvent composition and in some cases the sequence of stabilities is changed with changing the composition of the mixed solvents. The values of thermodynamic quantities (ΔH°c and ΔS°c) for formation of DBDA18C6-Ni²⁺, DBDA18C6-Cu²⁺, DBDA18C6-Ag⁺ and DBDA18C6-Cd²⁺ complexes were obtained from temperature dependence of the stability constants and the results show that the values of ΔH°c and ΔS°c for these complexes are sensitive to the nature and composition of AN–DMF binary solutions, but they do not vary monotonically with the solvent composition.     

Stability of crown-ether complexes with alkali-metal ions in ionic liquid-water mixed solvents

Stability constants of sodium and cesium ion complexes with 18-crown-6 (18C6) and dibenzo-18-crown-6 (DB18C6) in N-butyl-4-methyl-pyridinium tetrafluoroborate [BMP][BF₄] aqueous solutions were measured using the ²³Na and ¹³³Cs NMR technique at 23 °C. To the best of our knowledge, the estimated values of stability constants reported in this study are the first such values given for ionic liquid solutions. The cationic exchange between the free and complexed species is rapid, and only formation of the 1:1 complexes [M(18C6)]⁺ and [M(DB18C6)]⁺ (M = Na⁺, Cs⁺) were observed. The complex formation constants demonstrated a strong dependence on the [BMP][BF₄] concentration. For [M(18C6)]⁺, in solutions with a 0.33–0.70 mole fraction of water in [BMP][BF₄], lg K values are found to be more than one unit higher than the lg K values measured in pure aqueous solutions, although no information concerning the influence of [BMP][BF₄] on the complex formation selectivity could be observed. DB18C6 complexes revealed significantly lower stability under the same conditions. An extrapolation to zero water content gave the lg K = 2.42 for [Cs(18C6)]⁺ in [BMP][BF₄]. It was discovered that when added to water, [BMP][BF₄] increases the solubility of crown ethers and decreases the solubility of alkali metal nitrates. Complex formation with crown ethers enhances the solubility of alkali metal salts in [BMP][BF₄].     

Novel Photosensitive Polymer: Synthesis,Characterization and Thermal Properties of Polymer having Pendant Photocrosslinkable Group

New methacrylic monomer having free radical polymerizable methacryloyl group and photocrosslinkable functional group was synthesized by reacting hydroxyl chalcone with methacryloyl chloride. The monomer was homopolymerized in methyl ethyl ketone solvent using benzoyl peroxide as an initiator at 70°C. The prepared homopolymer was characterized by UV, FT‐IR, ¹H‐NMR and ¹³C‐NMR spectra. The molecular weights (M_w and M_n) were estimated by gel permeation chromatography. The thermal stability of the polymer was measured by thermogravimetric analysis. The glass transition temperature of the polymer was determined by differential scanning calorimetry. The photocrosslinking property of the polymer was also studied.     

Conductance Study of the Thermodynamics of Complexation of K+, Rb+, Cs+ and Tl+ Ions with Dibenzo-24-crown-8 in Binary Acetonitrile–Nitromethane Mixtures

The complexation reactions between dibenzo-24-crown-8 (DB24C8) and K⁺, Rb⁺, Cs⁺ and Tl⁺ ions were studied conductometrically in different acetonitrile–nitromethane mixtures at various temperatures. The formation constants of the resulting 1:1 complexes were calculated from the computer fitting of the molar conductance–mole ratio data at different temperatures. At 25 °C and in all solvent mixtures used, the stability of the resulting complexes varied in the order Tl⁺ > K⁺ > Rb⁺ > Cs⁺. The enthalpy and entropy changes of the complexation reactions were evaluated from the temperature dependence of formation constants. It was found that the stability of the resulting complexes increased with increasing nitromethane in the solvent mixture. The TΔS° vs. ΔH° plot of all thermodynamic data obtained shows a fairly good linear correlation indicating the existence of enthalpy–entropy compensation in the complexation reactions.     

Umsetzung von 1,5-Dimethyl-2,3,3,4-tetrachlor-1,5,2,4-diazadiphosphorinan-6-on mit Anilinderivaten,Heptamethyldisilazan und tert.-Butylamin: Oxidative Addition von Tetrachlor-o-benzochinon an einige P(III)-haltige Produkte

The reaction of the title compound 1 with the p-R-aniline derivatives (R═H, F, OCH₃, NO₂, and NH₂) led to the formation of the aza-2σ³,4σ³-diphosphetidines 2a– 2e, whereas 2-trimethylsiloxyaniline furnished the azadiphosphetidine 2f. The reaction of the sterically crowded 2,6-dimethylaniline with 1 furnished the disubstituted derivative 3. The tricyclic compound 5 was formed during the reaction of 1,2-phenylenediamine with 1. Heptamethyldisilazane formed the aza-2σ ³ ,4σ ³ -diphosphetidine 6 on reaction with 1. The bulkier tert.-butylamine formed with 1 a mixture of the aza-2,4-diphosphetidine 7a and the disubstituted derivative 7b, which could not be separated. The reaction of 2b and 6 with tetrachloro-o-benzoquinone resulted in the formation of the bis-spirophosphoranes 8 and 9b, respectively. The formation of the monospirophosphorane 9a was observed in the ³¹P NMR spectrum. The characterization of compounds is based in particular on NMR investigations (¹H, ¹³C, ³¹P). 2a was characterized by a single-crystal X-ray structure analysis. The dimethylurea fragment is planar; the four-membered ring is folded about the P···P vector by 38.7°.