Enhanced TiO2 surface electrochemistry with carbonised layer-by-layer cellulose-PDDA composite films

In this report we demonstrate a versatile (and potentially low-cost) cellulose nano-whisker-based surface carbonisation method that allows well-defined films of TiO(2) nanoparticles surface-modified with carbon to be obtained. In a layer-by-layer electrostatic deposition process based on TiO(2) nanoparticles, cellulose nano-whiskers, and poly(diallyl-dimethylammonium) or PDDA are employed to control the ratio of surface carbon to TiO(2). Characterisation based on optical, AFM, XRD, and XPS methods is reported. Electrochemical measurements suggest improved access to surface states, dopamine binding at the anatase surface, and surface redox cycling aided by the thin amorphous carbon film in mesoporous TiO(2). In future, the amorphous carbon layer method could be applied for surface processes for a wider range of semiconductor or insulator surfaces.     

Gold-Titanium(IV) Oxide Plasmonic Photocatalysts Prepared by a Colloid-Photodeposition Method: Correlation Between Physical Properties and Photocatalytic Activities

Colloidal gold (Au) nanoparticles were prepared and successfully loaded on titanium(IV) oxide (TiO(2)) without change in the original particle size using a method of colloid photodeposition operated in the presence of a hole scavenger (CPH). The prepared Au nanoparticles supported on TiO(2) showed strong photoabsorption at around 550 nm due to surface plasmon resonance (SPR) of Au and exhibited a photocatalytic activity in mineralization of formic acid in aqueous suspensions under irradiation of visible light (>ca. 520 nm). A linear correlation between photocatalytic activity and the amount of Au loaded, that is, the number of Au nanoparticles, was observed, indicating that the activity of Au/TiO(2) plasmonic photocatalysts can be controlled simply by the amount of Au loading using the CPH method and that the external surface area of Au nanoparticles is a decisive factor in mineralization of formic acid under visible light irradiation. Very high reaction rates were obtained in samples with 5 wt % Au or more, although the rate tended to be saturated. The CPH method can be widely applied for loading of Au nanoparticles on various TiO(2) supports without change in the original size independent of the TiO(2) phase. The rate of CO(2) formation also increased linearly with increase in the external surface area of Au. Interestingly, the TiO(2) supports showed different slopes of the plots. The slope is important for selection of TiO(2) as a material supporting colloidal Au nanoparticles.     

Tuning the solubility of TiO2 nanoparticles in apolar solvents by doping with Co2+

Anatase Co-doped TiO2 nanoparticles capped by oleic acid with a wide range of dopant concentrations (0-23.27%) were synthesized. The surface chemistry of the doped nanoparticles was probed by Fourier transform infrared spectroscopy and thermogravimetric analyses. An interesting effect of doping was discovered: doping with Co2+ at the nanocrystal surface significantly improves the solubility and dispersibility of the nanocrystals in apolar solvents, which can originate in the change in the self-assembled structure of the surface ligand from the weakly hydrophobic quasibilayer in undoped TiO2 nanorods to the strongly hydrophobic monolayer in Co-doped TiO2 nanocrystals.     

Effect of supporting surface layers on catalytic activities of gold nanoparticles in CO oxidation

The surfaces of fumed silica materials were modified with a surface sol-gel process for catalysis applications. This surface-modification approach allows not only a monolayer growth of TiO(2) or Al(2)O(3) but also a stepwise double-layer growth of TiO(2)/TiO(2), Al(2)O(3)/Al(2)O(3), TiO(2)/Al(2)O(3), or Al(2)O(3)/TiO(2) on the surfaces of the silica materials with a monolayer precision. XRD analyses revealed that the coated monolayers and double layers of TiO(2) and Al(2)O(3) were amorphous. Gold nanoparticles were successfully deposited on the above six surface-modified silica materials via a deposition-precipitation method. The catalytic activities of these six gold catalysts for CO oxidation are highly dependent on the structures of their surface monolayers or double layers. The gold catalyst supported on the silica material functionalized with a TiO(2) monolayer (Au/TiO(2)) is the most active in both as-synthesized and oxidized forms, while the gold catalyst supported on the silica material functionalized with an Al(2)O(3)/TiO(2) double layer (Au/Al(2)O(3)/TiO(2)/SiO(2)) is the most active in the reduced form among the six catalysts. Surprisingly, the gold catalyst supported on the silica material functionalized with a TiO(2)/Al(2)O(3) double layer (Au/TiO(2)/Al(2)O(3)/SiO(2)) has much less activity than Au/Al(2)O(3)/TiO(2)/SiO(2) under all various treatments, underscoring the sensitivity of the catalytic activity to the structure of the supporting surfaces.     

乙二醇表面改性纳米二氧化钛的制备及其对水性聚氨酯的改性

以乙二醇(EG)和钛酸四丁酯(TBOT)为原料,采用原位表面修饰方法成功制备了乙二醇表面改性纳米TiO2(EG-TiO2);利用傅立叶红外光谱仪、X射线衍射仪、透射电子显微镜表征了其结构,采用热重分析仪测定了其热稳定性.结果表明,经表面修饰的纳米二氧化钛在水性聚氨酯皮革涂饰剂(WPU)基体中分散良好;将EG-TiO2添加到WPU中能显著提高其抗紫外线性能、热稳定性及耐磨性能.     

Formation of different gold nanocrystal core-resin shell structures through the control of the core assembly and shell polymerization

The formation of different Au nanocrystal core-resin shell structures through the control of the nanocrystal assembly and shell polymerization is investigated. 4-Mercaptophenol is employed together with formaldehyde as the resin monomers. 4-Mercaptophenol molecules bond to the surface of Au nanocrystals so that the resultant phenolic resin can intimately encapsulate Au nanocrystals. The morphologies of the obtained structures are determined by the nanocrystal assembly and the monomer polymerization behaviors, which are controlled by the solution pH as well as the monomer amounts. At pH = 8-9, Au nanorods are assembled and fused together under hydrothermal conditions in a preferential end-to-end manner. The fused structures are coated with a layer of resin, with the thickness controlled by the supplied amounts of the monomers. At pH = ～10, Au nanorods are coated with resin of controllable thicknesses and separated from each other. The resin-coated Au nanorods are stable in both aqueous and nonaqueous solutions. At pH = ～12, Au nanorods are coated with a thin layer of resin and assembled together in a side-by-side manner. A similar assembly and resin coating behavior is also observed with Au nanopolyhedrons. Moreover, plasmonic-fluorescent bifunctional structures are readily produced by incorporating CdTe nanocrystals in the resin shell that is coated on Au nanocrystals, owing to the presence of a number of thiol groups in the resin shell.     

Synthesis of TiO2 nanoparticles on the Au(111) surface

The growth of titanium oxide nanoparticles on reconstructed Au(111) was investigated by scanning tunneling microscopy and x-ray photoelectron spectroscopy. Ti was deposited by physical-vapor deposition at 300 K. Regular arrays of titanium nanoparticles form by preferential nucleation of Ti at the elbow sites of the herringbone reconstruction. The titanium oxide nanoclusters were synthesized by subsequent exposure to O(2) at 300 K. Two-and three-dimensional titanium oxide nanocrystallites form during annealing in the temperature range from 600 to 900 K. At the same time, the Au(111) surface assumes a serrated 110-oriented step-edge morphology suggesting step-edge pinning by titanium oxide nanoparticles. The oxidation state of the titanium oxide nanoparticles varies with annealing temperature. Specifically, annealing to 900 K results in the formation of stoichiometric TiO(2) nanocrystals as judged by the Ti(2p) binding energies measured in the x-ray photoelectron data. The nanodispersed TiO(2) on Au(111) is an ideal system to test the various models proposed for the enhanced catalytic reactivity of supported Au nanoparticles.     

Mesoporous Au/TiO2 nanocomposite microspheres for visible-light photocatalysis

Mesoporous Au/TiO(2) nanocomposite microspheres have been synthesized by using a microemulsion-based bottom-up self-assembly (EBS) process starting from monodisperse gold and titania nanocrystals as building blocks. The microspheres had large surface areas (above 270 m(2) g(-1)) and open mesopores (about 5 nm), which led to the adsorption-driven concentration of organic molecules in the vicinity of the microspheres. Au nanoparticles, which were stably confined within the microspheres, enhanced the absorption over the broad UV/Vis/NIR spectroscopic range, owing to their strong surface plasmon resonance (SPR); as a result, the Au nanoparticles promoted the visible-light photo-induced degradation of organic compounds.     

Au@TiO2核壳纳米粒子光催化过程的表面增强拉曼光谱研究

利用聚电解质的静电吸附作用（层层组装）,在Au纳米粒子表面包裹上不同层数的二氧化钛前驱体TALH,通过退火形成Au@TiO2复合纳米粒子.以苯硫酚（TP）作为探针分子对退火前复合纳米粒子不同壳层厚度的SERS效应进行表征;可以发现：SERS信号强度的变化跟壳层厚度密切相关,当Au表面包裹至三层TALH时,信号几乎完全消失.此外,结合紫外照射,利用SERS对亚甲基蓝在TiO2壳层表面的光催化降解过程进行现场研究.结果表明：MB的降解主要经历了从多体及二聚体吸附逐渐向单体吸附方式转变,随后又经历了一个脱甲基的过程.因此,本工作发展了将一种紫外催化与现场SERS检测相结合的技术,该技术有望发展成为检测光催化过程,研究表面催化机理的一种强有力的工具     

Fabrication and characterization of core/shell structured TiO2/polyaniline nanocomposite

A novel core/shell structured TiO(2)/polyaniline nanocomposite was fabricated by grafting aniline on aminobenzoate monolayer that is chemically adsorbed on the TiO(2) nanocrystal surface. The formation and nanostructure of the nanocomposite were investigated by FT-IR and UV-Vis spectra, TEM, FE-SEM, and TG-DTA analysis. Adsorption of aminobenzoate on the TiO(2) surface is an effective method to obtain the uniform nanocomposite. The thickness of polyaniline layer coating on the TiO(2) nanocrystal surface can be controlled in a range of 2-5 nm by this method. A photoelectrochemical study was carried out on the TiO(2)/polyaniline nanocomposite, and found that polyaniline in the nanocomposite acted as a visible-light sensitizer in a photoelectrochemical reaction. The sensitization effect increased with increasing binding strength between polyaniline and TiO(2). A dye-sensitized solar cell with a short circuit current density of 0.19 mA/cm(2) and an open circuit voltage of 0.35 V was fabricated by using the TiO(2)/polyaniline nanocomposite film as a sensitized electrode.     

Thermal Degradation of Cellulose Nanocrystals Deposited on Different Surfaces

Thermal degradation of cellulose nanocrystals deposited on flat solid surfaces was monitored by AFM coupled with analysis of obtained images using image processor. The nanocrystals deposited on TiO₂ substrate showed different degradation patterns compared to those deposited on the nanosized layer of amorphous cellulose. The degradation was complete within 20 minutes at 300 °C. The nanocrystal deposited on amorphous cellulose resisted the heat treatment up to 120 minutes. Visual comparison and analysis of the AFM images clearly demonstrated the impact of temperature on the degradation rate of the nanocrystals deposited on TiO₂ substrate.     

同步辐射光电了能谱研究在团簇存金红石相TiO2-（1×1）表面的生长和稳定性

利用同步辐射高分辨光电子能谱研究了金团簇在部分还原TiO2-（1×1）表面的生长和稳定性．价带谱实验结果观察到非常少量金团簇的沉积导致了Ti^3＋的3d峰完全消失,表明金团簇成核在TiO2-（1×1）表面的氧缺陷位．Au4f芯电子光电子能谱实验结果证明了TiO2-（1×1）表面氧缺陷位向金团簇转移电荷．还对比研究了化学剂量比和部分还原的TiO2-（1×1）表面上金团簇的热稳定性．当金团簇尺寸相近时部分还原的TiO2-（1×1）表面上金团簇要比化学剂量比的TiO2-（1×1）面上金团簇稳定;在相同的表面上尺寸大的金团簇要比尺寸小的金团簇稳定．     

Single nanocrystals of anatase-type TiO2 prepared from layered titanate nanosheets: formation mechanism and characterization of surface properties

Anatase-type TiO2 single nanocrystals with boatlike, comblike, sheetlike, leaflike, quadrate, rhombic, and wirelike particle morphologies were prepared by hydrothermal treatment of a layered titanate nanosheet colloidal solution. The formation reactions and surface properties of the TiO2 nanocrystals were investigated using XRD, TEM, TG-DTA analyses, and measurements of BET specific surface area, photocatalytic activity, and ruthenium dye (N719) adsorption. The crystal morphology can be controlled by reaction temperature, pH value of reaction solution, and exfoliating agent. The titanate nanosheets were transformed to the TiO2 nanocrystals by two types of reactions. One is an in situ topotactic structural transformation reaction, and the other is a dissolution-deposition reaction on the surface. The anatase nanocrystals formed by the in situ topotactic structural transformation reaction retain the sheetlike particle morphology of the precursor, and they preferentially expose the (010) plane of anatase structure. The crystal surface of anatase nanocrystals prepared in this study showed higher photocatalytic activity and higher ruthenium dye adsorption capacity than did the Ishihara ST-01 sample, a standard anatase nanocrystal sample. The results indicated the (010) plane of the anatase structure has high photocatalytic activity and high ruthenium dye adsorption ability.     

Fabrication of platy apatite nanocrystals loaded with TiO2 nanoparticles by two-step emulsion method and their photocatalytic activity

Nanometer-sized TiO(2) island structure on the platy hydroxyapatite nanocrystals (HAp) has been accomplished by two-step emulsion process. At the first step, platy HAp nanocrystals, of which size was in the range of 70-200 nm after heat-treatment at 1078 K for 1 h, were prepared using the W/O emulsion system. Before the second step, HAp nanocrystals were immersed in NaH(2)PO(4) solution for the formation of hydroxyl group on their surface. In the following, titanium tetraisopropoxide reacted with the hydroxyl group of HAp surface to form TiO(2) nanoparticles on the surface of HAp nanocrystals, which were dispersed in the micrometer-sized methanol droplets of polyethylene cetylether-cyclohexane mixture (methanol/oil emulsion). The resulting hydroxyapatite nanocrystals loaded with TiO(2) nanoparticles showed the high photocatalytic activity comparing to the commercial TiO(2) catalyst.     

Interplay of three-dimensional morphologies and photocarrier dynamics of polymer/TiO2 bulk heterojunction solar cells

In this study, we investigated the interplay of three-dimensional morphologies and the photocarrier dynamics of polymer/inorganic nanocrystal hybrid photoactive layers consisting of TiO(2) nanoparticles and nanorods. Electron tomography based on scanning transmission electron microscopy using high-angle annular dark-field imaging was performed to analyze the morphological organization of TiO(2) nanocrystals in poly(3-hexylthiophene) (P3HT) in optimal solar cell devices. The Three-dimensional (3D) morphologies of these hybrid films were correlated with the photocarrier dynamics of charge separation, transport, and recombination, which were comprehensively probed by various transient techniques. Visualization of these 3D bulk heterojunction morphologies clearly reveals that elongated and anisotropic TiO(2) nanorods in P3HT not only can significantly reduce the probability of the interparticle hopping transport of electrons by providing better connectivity with respect to the TiO(2) nanoparticles, but also tend to form a large-scale donor-acceptor phase-separated morphology, which was found to enhance hole transport. The results support the establishment of a favorable morphology for polymer/inorganic hybrid solar cells due to the presence of the dimensionality of TiO(2) nanocrystals as a result of more effective mobile carrier generation and more efficient and balanced transport of carriers.     

Controlled synthesis of highly dispersed TiO2 nanoparticles using SBA-15 as hard template

Highly dispersed TiO2 nanoparticles were successfully synthesized by a wet impregnation method using SBA-15 as hard template for confining the growth of TiO2 nanocrystals, and then calcined at 550 degrees C in muffle furnace for 2 h. The as-synthesized samples were characterized with Fourier transform infrared spectra (FTIR), Raman spectroscopy, diffuse reflectance UV-visible spectroscopy (UV-vis), powder X-ray diffraction (XRD), small-angle X-ray diffraction (SAXRD), nitrogen adsorption, transmission electron microscopy (TEM) and photoluminescence spectra (PL). It was found that SBA-15 contained abundant silanol groups after removal of triblock copolymers by ethanol extraction and could easily adsorb a great number of titanium alkoxide via chemisorption. After subsequent hydrolysis of the anchored Ti complexes and calcination of the amorphous TiO2, anatase TiO2 nanocrystals with spherical shape and uniform particle diameter of about 6 nm were formed. A blue shift was observed in UV-vis absorption spectra due to the quantum size effect of TiO2 nanoparticles. Moreover, the as-prepared TiO2 nanoparticles showed a high PL intensity due to an increase in the recombination rate of photogenerated electrons and holes under UV light irradiation.     

Elimination of cross-talk and modulation of function in an organized heterosupramolecular assembly

A close-packed monolayer of TiO2 nanocrystals was deposited on a conducting glass support using Langmuir-Blodgett (LB) techniques and fired. A close-packed mixed monolayer of eicosyl phosphonic acid (I) and the viologen. 1,1'-dieicosyl-4,4'-bipyridinium dichloride (II) was then deposited on the TiO2 substrate, also using LB techniques. At sufficiently high dilutions of II in II a single viologen molecule is adsorbed with a known orientation at the surface of each nanocrystal. The resulting assembly was incorporated as the working electrode in an electrochemical cell. Under open circuit conditions, bandgap excitation of a TiO2 nanocrystal results in electron transfer to a viologen molecule. No electron transfer between the viologen molecules adsorbed at different nanocrystals is observed. At a positive applied potential, electron transfer following bandgap excitation is largely suppressed. Considered are the implications of these findings for the development of practical devices based on modulatable function addressable on the nanometer scale.     

【撤稿】Au纳米颗粒二维超晶格结构的稳定性

We synthesized 5.5 nm Au nanocrystals coated by dodecanethiol (C₁₂SH₂₆) by reverse micelle method. The Au nanocrystals are multiply twinned particles (MTP), which are mainly characterized by decahedral and icosahedral structures. The 2D hexagonal network self-organizationa of Au nanocrystals are realized on both amorphous carbon (AC) and highly oriented pyrolitic graphite (HOPG) surfaces. The stability of 2D superlattices of Au nanocrystals in vacuum has been systematically surveyed, and it is found that large single triangular nanocrystals have been formed after 75 days due to the coalescence among the neighboring nanoparticles and the rearrangement of the atomics. When the Au nanocrystals in 2D organizations are annealed in air (573 K, 15 min), higher ordered 2D self-assemblies are stable, whereas worm-like coalesced nanoparticles form in those less ordered organizations. This demonstrates that the thermal stability of 2D self-assemblies is determined by the level of nanocrystals ordering.     

Gold nanoparticle-decorated keggin ions/TiO2 photococatalyst for improved solar light photocatalysis

We demonstrate a facile localized reduction approach to synthesizing a Au nanoparticle-decorated Keggin ion/TiO(2) photococatalyst for improved solar light photocatalysis application. This has been achieved by exploiting the ability of TiO(2)-bound Keggin ions to act as a UV-switchable, highly localized reducing agent. Notably, the approach proposed here does not lead to contamination of the resultant cocatalyst with free metal nanoparticles during aqueous solution-based synthesis. The study shows that for Keggin ions (phosphotungstic acid, PTA), being photoactive molecules, the presence of both Au nanoparticles and PTA on the TiO(2) surface in a cocatalytic system can have a dramatic effect on increasing the photocatalytic performance of the composite system, as opposed to a TiO(2) surface directly decorated with metal nanoparticles without a sandwiched PTA layer. The remarkable increase in the photocatalytic performance of these materials toward the degradation of a model organic Congo red dye correlates to an increase of 2.7-fold over that of anatase TiO(2) after adding Au to it and 4.3-fold after introducing PTA along with Au to it. The generalized localized reduction approach to preparing TiO(2)-PTA-Au cocatalysts reported here can be further extended to other similar systems, wherein a range of metal nanoparticles in the presence of different Keggin ions can be utilized. The composites reported here may have wide potential implications toward the degradation of organic species and solar cell applications.     

Composite Au/TiO(2) Nanoparticles: Synthesis, Characterization, and Assembly by Using Potentiostatic Technique

Composite Au/TiO(2) nanoparticles were synthesized using TiO(2) nanoparticles as nuclei. The particles were characterized by UV-vis spectroscopy, zeta potential, EDS, and TEM. The mean diameter of the particles is about 23.6 nm, and the position of the surface plasma absorption band peak is at 533 nm, with a red shift of 15 nm compared with that of Au sol. The zeta potential is +31.3 mV. Monolayers of composite Au/TiO(2) nanoparticles were obtained using the potentiostatic technique. Copyright 2000 Academic Press.