Analysis of triacylglycerol and fatty acid isomers by low-temperature silver-ion high performance liquid chromatography with acetonitrile in hexane as solvent: limitations of the methodology

Silver ion HPLC (Ag-HPLC), utilizing columns containing silver ions bonded to a silica substrate and acetonitrile in hexane as solvent, has proven to be a powerful technology for the analysis of geometric (cis or trans) or positional fatty acids, fatty acid ester (primarily methyl ester; FAME), or triacylglycerol (TAG) isomers. Previous studies had demonstrated that, unlike gas chromatography, samples eluted more rapidly at lower temperatures (at 20 degrees C versus 40 degrees C, for example). A low-temperature bath [dual-column Ag-HPLC; isocratic solvent systems of 0.3 to 0.7% acetonitrile (ACN) in hexane] was utilized to study the application of this system at low (below 0 degrees C) temperatures for analysis of FAME (zero to six double bonds) and TAG [SSS, OOO and LLL, where S=stearic acid (18:0), O=oleic acid (9c-18:1), and L=linoleic acid (9c, 12c-18:2)] standards. While FAME elution times continued to decrease from 0 degrees C to -10 degrees C, they began to increase at -20 degrees C. A similar situation was noted for the TAG isomers, except that retention times began to increase below 0 degrees C. The lower temperature limit of the Ag-HPLC/ACN in hexane system is thus ca. -25 degrees C. Increasing sample elution times and pump head pressures upon sample injection were noted at temperatures of -25 degrees C to -40 degrees C. Equilibration times at each temperature could be reduced to ca. 15 min without loss of resolution and with retention times of +/-2%. Temperature, rather than solvent composition, can therefore be utilized with the Ag-HPLC/ACN in hexane solvent system to optimize elution times and resolution(s) of FAME and TAG isomers.     

Separation of conjugated linoleic acid methyl esters by silver-ion high performance liquid chromatography in semi-preparative mode

Silver-ion HPLC (Ag-HPLC) has been utilized to separate a variety of unsaturated fatty acid methyl esters (FAMEs) by configuration, location or number of olefinic or acetylenic bonds. Two analytical Ag-HPLC columns connected in series and an isocratic solvent system of acetonitrile (ACN) in hexane were used to fractionate 10-15 mg samples of a mixture of two deuterium-labeled isomers of conjugated linoleic acid (Z9.E11- and Z9,Z11-octadecadienoic acid-17,17,18,18-d4). "Baseline" (> 95%) resolution of the two isomers, which decreased with increasing weights of sample injected, was maintained by careful adjustment of the percentage of ACN in the ACN/hexane solvent system. Chemical purities of the isolated FAME were > 96%.     

Analytical monitoring of the production of biodiesel by high-performance liquid chromatography with various detection methods.

Gradient elution reversed-phase high-performance liquid chromatography (RP-HPLC) was used for the determination of compounds occurring during the production of biodiesel from rapeseed oil. Individual triacylglycerols (TGs), diacylglycerols, monoacylglycerols and methyl esters of oleic, linoleic and linolenic acids and free fatty acids were separated in 25 min using a combined linear gradient with aqueous-organic and non-aqueous mobile phase steps: 70% acetonitrile+30% water in 0 min, 100% acetonitrile in 10 min, 50% acetonitrile+50% 2-propanol-hexane (5:4, v/v) in 20 min and 5 min final hold-up. Another method with a non-aqueous linear mobile phase gradient [from 100% methanol to 50% methanol+50% 2-propanol-hexane (5:4, v/v) in 15 min] was used for fast monitoring of conversion of rapeseed oil triacylglycerols to fatty acid methyl esters and for quantitation of residual TGs in the final biodiesel product. Sensitivity and linearity of various detection modes (UV detection at 205 nm, evaporative light scattering detection and mass spectrometric detection) were compared. The individual sample compounds were identified using coupled HPLC-atmospheric pressure chemical ionization mass spectrometry in the positive-ion mode.     

Improved identification of conjugated linoleic acid isomers using silver-ion HPLC separations

Silver-ion high-performance liquid chromatography (Ag+-HPLC) has been shown to be effective in the resolution of most of the isomers of conjugated octadecadienoic acids (18:2), also known as conjugated linoleic acid (CLA). The CLA isomers identified in natural fats from ruminants are a mixture of numerous positional and geometric isomers from 7,9- to 12,14-18:2. Ag+-HPLC separates both geometric (trans,trans < cis/trans < cis,cis) and positional CLA isomers using the mobile phase hexane/acetonitrile (99.9:0.1). The elution volumes for the CLA isomers were not only affected by the concentration of acetonitrile (in the prepared mobile phase) but also with successive runs during the day using a prepared mobile phase batch, due to the partial solubility of acetonitrile in hexane. However, this drift does not affect the relative resolution of the CLA isomers. The addition of diethyl ether to the mobile phase partly stabilizes the solvent mixture. In order to facilitate the interpretation of Ag-+HPLC chromatograms, the relative retention volumes (RRV) were calculated for each CLA isomer. Toluene was added to all the test portions and served as an estimator of dead volume, whereas the elution of the ubiquitous 9c,11t-CLA isomer was chosen as unity (1.00). Expressing the elution of all the CLA isomers as their RRV greatly helped to standardize each CLA isomer, resulting in relatively small coefficients of variation (% CV) for the trans,trans (<1.5%) and cis/trans (<0.5%) CLA isomers. The identification of the CLA isomers was further facilitated by synthesis of authentic CLA isomers. All the geometric CLA fatty acid methyl esters (FAME) from positions 6,8- to 13,15-CLA were commercially available or synthesized by a combination of partial hydrazine reduction of known polyunsaturated fatty acids followed by alkali isomerization, isolation of products, and further iodine-catalyzed geometric isomerization. Based on expressing the elution volume as RRV and the availability of the synthetic CLA isomers, a unique reversal of the elution order of the c/t CLA isomers was found. It is also proposed that the retention times of CLA isomers by gas chromatography (GC) should be expressed as their relative retention times (RRT) relative to methyl gamma-linoleneate. The availability of CLA reference materials and the application of RRV and RRT to Ag+-HPLC and GC separations, respectively, will greatly improve in the identifications of CLA isomers.     

Comprehensive two-dimensional liquid chromatography with ultraviolet, evaporative light scattering and mass spectrometric detection of triacylglycerols in corn oil

An improved comprehensive two-dimensional (LC x LC) HPLC system for the analysis of triacylglycerols was developed. In the first-dimension, a Ag(I)-coated cation exchanger (250 mm x 2.1 mm, 5 microm) was employed with a gradient from 100% MeOH to 6% MeCN in MeOH at 20 microL/min. Using a 10-way valve with two switching loops, 1 min sections of the first-dimension were introduced in the second-dimension consisting of a 30 mm x 4.6 mm C18 (1.8 microm) column with an isocratic mobile phase of methanol-methyl tert-butyl ether (70:30) at 3.0 mL/min. As the second-dimension solvent was stronger than the first-dimension solvent, focusing in the second-dimension took place, leading to better separations than in previously reported analyses in which hexane was the main constituent of the first-dimension eluent. Compounds differing by 2 in their partition number were baseline separated in the second-dimension. Detection took place by UV at 210 nm, evaporative light scattering and (+)-atmospheric pressure chemical ionisation-MS with the latter giving the best results. Corn oil was investigated and 44 compounds could be detected: 34 triacylglycerols (TAGs), 8 oxygenated TAGs, and 2 TAGs containing a trans double bond. Data manipulation allowed the construction of contour plots and the automated calculation of the first- and second-dimension retention times and peak areas. Quantitative results are compared with a fatty acid methyl ester analysis, and with literature data.     

Determination of low levels of an antioxidant in polyolefins by large-volume injection temperature-programmed packed capillary liquid chromatography

Sub-ambient column temperatures, promoting strong interactions between the analyte and the stationary phase material, were utilized to focus large volumes of the polyolefin antioxidant Irganox 1076 [benzenepropanoic acid, 3.5-bis(1,1-dimethylethyl)-4-hydroxy-, octadecyl ester] on the column inlet, using pure acetonitrile as sample solvent and mobile phase. Injection volumes up to 100 microl were successfully employed on a 50 cm x 320 microm I.D. capillary column packed with 5 microm Kromasil 100 ODS particles. Irganox 1076 was eluted after completed injection by temperature programming, using a temperature program from 7 to 90 degrees C, in 3 degrees C min(-1). UV detection, using a low-dispersion "U"-shaped flowcell, was performed at 280 nm. The method was applied for the determination of Irganox 1076 that was extracted from low-density polyethylene (0.6 ppm, w/w). Both Soxhlet and microwave-aided solvent extractions were performed, using chloroform and acetonitrile as solvents, respectively. The microwave-aided extraction with acetonitrile was found to give approximately the same yield as the standard Soxhlet reference method. Consequently, small volumes of acetonitrile could be used both as extraction solvent, sample solvent and mobile phase, simplifying the analysis process. The mass limit of detection of the method was found to be 3.3 ng, corresponding to a concentration limit of detection of 33 ng ml(-1), utilizing an injection volume of 100 microl. The within and between day precision of retention times displayed relative standard deviations below 1.2%.     

高效液相色谱分析鱼毒性藻类海洋卡盾藻溶血毒素

采用高效液相色谱技术(HPLC)分离和分析了海洋卡盾藻(香港株)溶血毒素的甲醇粗提物,通过对比不同流动相、检测波长、等度和梯度洗脱方式,初步建立了分析其溶血毒素的HPLC方法.结果表明,采用梯度洗脱的方法,海洋卡盾藻溶血毒素的粗提物在50 min内取得了较好地分离.色谱条件为C8硅胶柱(4.6 mm× 150 mm,5 μm),流动相为乙腈和水,梯度洗脱(0～10 min,60％→80％乙腈;10～40 min,80％ →90％乙腈;40～50 min,90％乙腈);紫外检测器检测波长为205和448nm;流速为0.8 mL/min;柱温为25℃.用兔血红细胞法对各个主要色谱峰进行溶血活性检测显示,海洋卡盾藻(香港株)的溶血毒素至少含有5种成分.光谱分析显示一种成分的紫外吸收高峰在448 nm,一种未完全分离的混合组分的紫外吸收高峰为440和446nm,另外3种成分的紫外吸收高峰为205 nm.     

Use of triacylglycerol profiles established by high performance liquid chromatography with ultraviolet-visible detection to predict the botanical origin of vegetable oils

A method for the determination of triacylglycerols (TAGs) in vegetable oils from different botanical origins by HPLC with UV-vis detection has been developed. Using a core-shell particle packed column (C18, 2.6 μm), TAG separation was optimized in terms of mobile phase composition and column temperature. Using isocratic elution with acetonitrile/n-pentanol at 10 °C, excellent efficiency with good resolution between most of the TAG peak pairs, within a total analysis time of 15 min, was achieved. Using mass spectrometry detection, a total of 15 peaks, which were common to oils of six different botanical origins (corn, extra virgin olive, grapeseed, hazelnut, peanut and soybean) were identified. These peaks were used to construct linear discriminant analysis (LDA) models for botanical origin prediction. Ratios of the peak areas selected by pairs were used as predictors. All the oils were correctly classified with assignment probabilities higher than 95%.     

Development and validation of a HPLC method for determination of levonorgestrel and quinestrol in rat plasma

Levonorgestrel and quinestrol, commonly known as EP‐1, has long been used in the control of wild rodents. Up to the present time, however, no method for simultaneous quantification of levonorgestrel and quinestrol in rat plasma has been reported. In the present study, a sensitive reverse‐phase high‐performance liquid chromatography with ultraviolet detection (RP‐HPLC‐UV) method for quantification of levonorgestrel and quinestrol in rat plasma has been developed. It uses a Kromasil ODS C₁₈ column and acetonitrile‐0.1% formic acid (85 : 15, v/v) mobile phase at ambient temperature. The plasma sample was prepared by hexane–isoamyl alcohol extraction (90 : 10, v/v). The flow rate and detection wavelength were 1.0 mL/min and 230 nm. The correlation coefficients were greater than 0.9995 within 0.08–50 μg/mL for levonorgestrel and 0.12–50 μg/mL for quinestrol, and the limits of detection were 0.02 and 0.05 μg/mL for levonorgestrel and quinestrol, respectively. Average recovery ranged from 92.5 to 96.3% and inter‐day RSDs were less than 7.56%. This method can be applied to the further pharmacokinetic study of levonorgestrel and quinestrol in rat plasma. Copyright © 2009 John Wiley & Sons, Ltd.     

Molecularly imprinted solid-phase extraction for the screening of antihyperglycemic biguanides

A new molecularly imprinted polymer (MIP) was specifically synthesized as a smart material for the recognition of metformin hydrochloride in solid-phase extraction. Particles of this MIP were packed into a stainless-steel tubing (50 mm x 0.8 mm i.d.) equipped with an exit frit. This micro-column was employed in the development of a molecularly imprinted solid-phase extraction (MISPE) method for metformin determination. The MISPE instrumentation consisted of a micrometer pump, an injector valve equipped with a 20-microl sample loop, a UV detector, and an integrator. With CH3CN as the mobile phase flowing at 0.5 ml/min, 95 +/- 2% binding could be achieved for 1200 ng of metformin from one injection of a phosphate-buffered sample solution (pH 2.5). Methanol + 3% trifluoroacetic acid was good for quantitative pulsed elution (PE) of the bound metformin. The MISPE-PE method, with UV detection at 240 nm, afforded a detection limit of 16 ng (or 0.8 microg/ml) for metformin. However, the micro-column interacted indiscriminately with phenformin with a 49 +/- 2% binding. A systematic investigation of binding selectivity was conducted with respect to sample composition (including the solvent, matrix, pH, buffer and surfactant effects). An intermediate step of differential pulsed elution used acetonitrile with 5% picric acid to remove phenformin and other structural analogues. A final pulsed elution of metformin for direct UV detection was achieved using 3% trifluoroacetic acid in methanol.     

Determination of paclitaxel in human and rat blood samples after administration of low dose paclitaxel by HPLC-UV detection

A simple and sensitive HPLC-UV method was developed for the determination of paclitaxel (TXL) in human and rat blood samples. 4-Hydroxybenzoic acid n-hexyl ester was used as an internal standard. TXL was extracted by a liquid-liquid extraction with tert-butylmethyl ether. The disturbing peaks in the case of serum sample were removed by pre-extraction with hexane. The separation of TXL was achieved within 25 min using an ODS column with 50% acetonitrile aqueous solution as a mobile phase at a flow rate of 1.0 mL/min. The eluent was monitored at 230 nm, and the resulted retention times of TXL and IS were 11.2 and 20.4 min. The detection limits of TXL for human plasma, serum and rat plasma samples at a signal-to-noise ratio of 3 were 10, 9.5 and 7.5 ng/mL, respectively. The proposed methods were applicable to the determination of TXL in human patients' plasma ranging from 15 to 27 ng/mL. Furthermore, monitoring of the time course of TXL after its single administration to rat could be demonstrated.     

Gradient reversed-phase high-performance liquid chromatographic separation of naturally occurring retinoids

A gradient reversed-phase high-performance liquid chromatographic technique is described for the facile separation and quantitation of the naturally occurring retinoids: retinoic acid, retinol, and retinyl esters. An octadecylsilane column (Waters mu Bondapak C18) is used, with gradient elution from methanol--water (80:20) (solvent A) to 70% or 100% methanol--tetrahydrofuran (50:50) (solvent B) at 2.0 ml/min; detection is by absorbance at 325 nm. Analysis can be completed, with return to starting conditions, in 25-30 min. The method is inherently flexible: retinyl esters can be eluted as a group, with little resolution, by gradient to 100% solvent B, or mostly resolved by gradient to 70% solvent B; separation of retinoids more polar than retinoic acid can be achieved by use of greater proportions of water in solvent A. The separation of vitamin A compounds from extracts of human, rat, and pig liver and from rat kidney by this technique is described.     

Liquid Chromatographic Determination of 4-Amino-N-(2,6-dimethylphenyl)-benzamide in Rat Serum and Urine

Abstract

The compound 4-amino-N-(2,6-dimethylphenyl)-benzamide has shown potential as a new anticonvulsant. A method for the liquid chromatographic determination of serum and urine concentrations of the compound and its N-acetylated metabolite was developed for pharmacokinetic studies. Quantitation was achieved via UV detection at 275 nm following isocratic reversed phase (C₁₈) separation using a ternary solvent system of water:acetonitrile:acetic acid (60:39:1) at a flow rate of 1.5 mL/min. The compounds were isolated from a 50 μL sample of serum using solid phase extraction with prior protein precipitation. The compounds and internal standard were eluted from the extraction column with acetonitrile. Isolation from urine was achieved similarly with the exclusion of protein precipitation. The assay procedure is useful for the determination of concentrations of parent compound from 0.68 to 204.6 μg/mL.     

Phthalates determination in pharmaceutical formulae used in parenteral nutrition by LC-ES-MS: importance in public health

A method for determining a group of phthalate esters in pharmaceutical formulae used in parenteral nutrition samples (with and without vitamins) has been developed. The phthalic acid esters (PAEs) studied were dimethyl phthalate, diethyl phthalate, butyl benzyl phthalate, dibutyl phthalate, di-(2-ethylhexyl) phthalate, and dioctyl phthalate. This group of phthalates was determined by high performance liquid chromatography (HPLC)–electrospray ionization–mass spectrometry, working in positive ion mode. The phthalates analyzed were extracted from the sample using hexane and sodium hydroxide. The hexane was then evaporated, and the compounds were redissolved in acetonitrile. The compounds were separated by HPLC working in gradient mode with acetonitrile-ultrapure water starting from 5% to 75% acetonitrile in 5 min, followed by isocratic elution for 27 min. Standard calibration curves were linear for all the analytes over the concentration range 10–250 μg L⁻¹. The method was precise (with RSD from 3.3% to 12.9%) and sensitive. The proposed analytical method has been applied to the analysis of these compounds in different pharmaceutical formulae (with different compositions) for parenteral nutrition samples in order to check the presence of phthalates and determine their concentration.     

Indirect resolution of baclofen enantiomers from pharmaceutical dosage form by reversed-phase liquid chromatography after derivatization with Marfey's reagent and its structural variants

A high-performance liquid chromatographic (HPLC) method was developed for chiral assay of baclofen enantiomers in pharmaceutical formulations using an indirect approach. Baclofen enantiomers were derivatized with Marfey's reagent (FDNP-L-Ala-NH2) and its structural variants FDNP-L-Phe-NH2, FDNP-L-Val-NH2, FDNP-L-Leu-NH2 and FDNP-L-Pro-NH2. The resultant diastereomers were separated on RP-TLC [triethylammonium phosphate buffer (pH 4.0, 50 mm)-acetonitrile, 50:50] and on a C18 column using a linear gradient (45 min) of acetonitrile and 0.01% aqueous trifluoroacetic acid (TFA) with UV detection at 340 nm. The differences in the retention times (Delta t R) of diastereomers due to the five chiral reagents were compared. The maximum and minimum difference in retention times between separated diastereomers was for FDNP-L-Leu-NH2 and FDNP-L-Pro-NH2, respectively. The effect of flow rate, acetonitrile content and TFA concentration on resolution was studied. The method was validated for linearity, repeatability, limit of detection and limit of quantification.     

Optimization and application of methods of triacylglycerol evaluation for characterization of olive oil adulteration by soybean oil with HPLC-APCI-MS-MS

Triacylglycerols (TAGs) are the main constituents of vegetable oils where they occur in complex mixtures with characteristic distributions. Mass spectrometry using an atmospheric pressure chemical ionization interface (APCI-MS) run in positive mode and an Ion Trap mass analyser were applied in the study of olive and soybean oils and their mixtures. Direct injections of soybean and olive oil solutions allowed the identification of ions derived from the main TAGs of both oils. This procedure showed to be a simple and powerful tool to evaluate mixtures or addition of soybean to olive oil. TAG separation was optimized by high performance liquid chromatography (HPLC) using an octadecylsilica LiChrospher column (250 mm × 3 mm; 5 μm) and a gradient composed of acetonitrile and 2-propanol allowed the separation of the main TAGs of the studied oils. APCI vaporization temperature was optimized and best signals were obtained at 370 °C. Multiple reaction monitoring (MRM) employing the transition of the protonated TAG molecules ([M+H]⁺) to the protonated diacylglycerol fragments ([M+H−R]⁺) improved the selectivity of TAG detection and was used in quantitative studies. Different strategies were developed to evaluate oil composition following TAG analysis by MRM. The external standard calibration and standard additions methods were compared for triolein quantification but the former showed to be biased. Further quantitative studies were based on the estimates of soybean and olive oil proportions in mixtures by comparison of TAG areas found in mixtures of known and unknown composition of both oils. Good agreement with expected or labeled values was found for a commercial blend containing 15% (w/w) of olive oil in soybean oil and to a 1:1 mixture of both oils, showing the potential of this method in characterizing oil mixtures and estimating oil proportions. Olive oils of different origins were also evaluated by mass spectra data obtained after direct injections of oil solutions and principal component analysis (PCA). Argentinean olive oils were clustered in a different area of the principal components plot (PC2 × PC1) in comparison with European olive oils. The commercial blend containing 15% (w/w) of olive oil in soybean oil appeared in a completely different area of the graphic, showing the potential of this method to screen out for olive oil adulterations.     

Simultaneous Determination of Glyphosate,Glufosinate, and Aminomethylphosphonic Acid by Capillary Electrophoresis After 9‐Fluorenylmethyl Chloroformate Derivatization

A capillary electrophoresis (CE) with UV absorption detection method is described for the simultaneous determination of glufosinate, glyphosate, and aminomethylphosphoric acid. The 9‐fluorenylmethyl chloroformate (FMOC‐Cl) was used for precolumn derivatization of the non‐absorbing herbicides. The three analytes were separated by CE in 9 min with 25 mM borate buffer at pH 9, followed by detection with a UV detector at 260 nm. We demonstrate how the detection limit can be enhanced by using acetonitrile‐salt mixtures. With acetonitrile‐salt mixtures, the limit of detection (LOD) was in the 10^?7 M range. Linearity of more than two orders of magnitude was generally obtained. Precisions of migration times and peak areas were less than 0.9% and 7.5%, respectively. The applicabilities of the method for the analysis of ground water and lake water were examined.     

Acrylate ester-based monolithic columns for capillary electrochromatography separation of triacylglycerols in vegetable oils

A simple and reliable method for the evaluation of triacylglycerols (TAGs) in vegetable oils by capillary electrochromatography (CEC) with UV-Vis detection, using octadecyl acrylate (ODA) ester-based monolithic columns, has been developed. The percentages of the porogenic solvents in the polymerization mixture, and the mobile phase composition, were optimized. The optimum monolith was obtained at the following ratios: 40:60% (wt/wt) monomers/porogens, 60:40% (wt/wt) ODA/1,3-butanediol diacrylate and 23:77% (wt/wt) 1,4-butanediol/1-propanol (14 wt% 1,4-butanediol in the polymerization mixture). A satisfactory resolution between TAGs was achieved in less than 12 min with a 65:35 (v/v) acetonitrile/2-propanol mixture containing 5 mM ammonium acetate. The method was applied to the analysis of TAGs of vegetable oil samples. Using linear discriminant analysis of the CEC TAG profiles, the vegetable oils belonging to six different botanical origins (corn, extra virgin olive, hazelnut, peanut, soybean and sunflower) were correctly classified with an excellent resolution among all the categories.     

Determination of tetracyclines residues in honey by on-line solid-phase extraction high-performance liquid chromatography

An automated system using on-line solid-phase extraction (SPE) high-performance liquid chromatography (HPLC) with ultraviolet (UV) detection was developed for the determination of tetracyclines (TCs), such as tetracycline (TC), oxytetracycline (OTC), chlortetracycline (CTC), metacycline (MC), and doxycycline (DC) in honey. One milliliter diluted honey sample was injected into a conditioned C18 SPE column and the matrix was washed out with water for 3 min. By rotation of the switching valve, TCs were eluted and transferred to the analytical column by the chromatographic mobile phase. Chromatographic conditions were optimized. TCs were separated in less than 8 min with a gradient elution using a mixture of 0.8% formic acid and acetonitrile. The UV detection was performed at 365 nm. The conditions for on-line SPE, including solvent and total time for loading sample and washing matrix were also optimized. Time for extraction and separation decreased greatly. For the five kinds of TCs, the limits of detection (LODs) at a signal-to-noise of 3 ranged from 5 to 12 ng g⁻¹. The relative standard deviations (R.S.D.) for the determination of TCs ranged from 3.4 to 7.1% within a day and ranged from 3.2 to 8.9% in 3 days, respectively.