Electrocatalytic mechanism and kinetics of SOMs oxidation on ordered PtPb and PtBi intermetallic compounds: DEMS and FTIRS study

The electrocatalytic activities and mechanisms of PtPb and PtBi ordered intermetallic phases towards formic acid, formaldehyde and methanol oxidation have been studied by DEMS and FTIRS, and the results compared to those for a pure polycrystalline platinum electrode. While PtPb exhibits an enhanced electrocatalytic activity for the oxidation of all three organic molecules when compared to a Pt electrode, PtBi exhibits an enhanced catalytic activity towards formic acid and formaldehyde oxidation, but not methanol. FTIRS data indicate that adsorbed CO does not form on PtPb or PtBi intermetallic compounds during the oxidation of formic acid, formaldehyde and methanol, and therefore their oxidation on both PtPb and PtBi intermetallic compounds proceeds via a non-CO(ads) pathway. Quantitative DEMS measurements indicate that only CO(2) was detected as a final product during formic acid oxidation on Pt, PtPb and PtBi electrodes. At a smooth polycrystalline platinum electrode, the oxidation of formaldehyde and methanol produces mainly intermediates (formaldehyde and formic acid), while CO(2) is a minor product. In contrast, CO(2) is the major product for formaldehyde and methanol oxidation at a PtPb electrode. The high current efficiency of CO(2) formation for methanol and formaldehyde oxidation at a PtPb electrode can be ascribed to the complete dehydrogenation of formaldehyde and formic acid due to electronic effects. The low onset potential, high current density and high CO(2) yield make PtPb one of the most promising electrocatalysts for fuel cell applications using small organic molecules as fuels.     

Electrocatalytic activity of ordered intermetallic phases for fuel cell applications

The electrocatalytic activities of a wide range of ordered intermetallic phases toward a variety of potential fuels have been studied, and results have been compared to those of a pure polycrystalline platinum (Pt(pc)) electrode. A significant number of the ordered intermetallic phases exhibited enhanced electrocatalytic activity when compared to that of Pt, in terms of both oxidation onset potential and current density. The PtBi, PtIn, and PtPb ordered intermetallic phases appeared to be the most promising electrocatalysts tested thus far for fuel cell applications. PtPb, in particular, showed an onset potential that was 100 mV less positive and a peak current density approximately 40 times higher than those observed for Pt in the case of methanol oxidation. The ability to control the geometric and electronic structures of the electrocatalytic material by using ordered intermetallic phases has been shown to be a promising direction of inquiry in the search for superior electrocatalysts for fuel cell applications.     

Electrocatalytic performance of fuel oxidation by Pt3Ti nanoparticles

A Pt-based electrocatalyst for direct fuel cells, Pt3Ti, has been prepared in the form of nanoparticles. Pt(1,5-cyclooctadiene)Cl2 and Ti(tetrahydrofuran)2Cl4 are reduced by sodium naphthalide in tetrahydrofuran to form atomically disordered Pt3Ti nanoparticles (FCC-type structure: Fm3m; a = 0.39 nm; particle size = 3 +/- 0.4 nm). These atomically disordered Pt3Ti nanoparticles are transformed to larger atomically ordered Pt3Ti nanoparticles (Cu3Au-type structure: Pm3m; a = 0.3898 nm; particle size = 37 +/- 23 nm) by annealing above 400 degrees C. Both atomically disordered and ordered Pt3Ti nanoparticles show lower onset potentials for the oxidation of formic acid and methanol than either pure Pt or Pt-Ru nanoparticles. Both atomically disordered and ordered Pt3Ti nanoparticles show a much lower affinity for CO adsorption than either pure Pt or Pt-Ru nanoparticles. Atomically ordered Pt3Ti nanoparticles show higher oxidation current densities for both formic acid and methanol than pure Pt, Pt-Ru, or atomically disordered Pt3Ti nanoparticles. Pt3Ti nanoparticles, in particular the atomically ordered materials, have promise as anode catalysts for direct fuel cells.     

Nanostructure PtRu/MWNTs as anode catalysts prepared in a vacuum for direct methanol oxidation

Platinum and ruthenium nanoparticles that are uniformly dispersed on multiwalled carbon nanotubes (MWNTs) were synthesized by vacuum pyrolysis using Pt(acac)2 and Ru(acac)3 as the metal precursors. The resulting nanocomposites were characterized by transmission electron microscopy and X-ray diffraction. The Pt, Pt45Ru55, and Ru nanoparticles had mean diameters of 3.0 +/- 0.6, 2.7 +/- 0.6, and 2.5 +/- 0.4 nm and the same mole number as their metal precursors at 500 degrees C. The electrocatalytic activity of the Pt/MWNTs and PtRu/MWNTs was investigated at room temperature by cyclic voltammetry and chronoamperometry. All of the electrochemical results showed that the PtRu/MWNTs exhibited a high level of catalytic activity for methanol oxidation as a result of the large surface area of the supporting carbon nanotubes and the wide dispersion of the Pt and Ru nanoparticles. Compared with the Pt/MWNTs, the onset potential for methanol oxidation of the PtRu/MWNTs was significantly lower, and the ratio of the forward anodic peak current to the reverse anodic peak current during methanol oxidation was somewhat higher. The Pt45Ru55/MWNTs displayed the best electrocatalytic activity of all of the carbon-nanotube-supported Pt and PtRu catalysts.     

X-ray fluorescence investigation of ordered intermetallic phases as electrocatalysts towards the oxidation of small organic molecules

The composition of ordered intermetallic nanoparticles (PtBi and PtPb) has been quantitatively studied by in situ X-ray fluorescence (XRF) during active electrochemical control in solutions of supporting electrolyte and small organic molecules (SOMs). Because the Pt L(β1,2) lines and the Bi L(α1,2) lines are only separated by 200 eV, an energy-dispersive detector and a multiple-channel analyzer (MCA) were used to record the major fluorescent emission lines from these two elements. The molar ratios of platinum to the less-noble elements (Bi, Pb) in the nanoparticles dramatically changed as a function of the applied upper limit potentials (E(ulp)) in cyclic voltammetric (CV) characterization. Similar to previous investigations for bulk intermetallic surfaces, the less-noble elements leached out from the surfaces of the intermetallic nanoparticles. For PtBi nanoparticles, the ratios of fluorescence intensities of Pt/Bi in the samples were 0.42, 0.96, and 1.36 for E(ulp)=+0.40, +0.80, and 1.20 V, respectively, while cycling the potential from -0.20 V to the E(ulp) value for 10 cycles. The leaching-out process of the less-noble elements occurred at more negative E(ulp) values than expected. After cycling to relatively positive E(ulp) values, nonuniform PtM (M=Bi of Pb) nanoparticles formed with a Pt-rich shell and intermetallic PtM core. When the supporting solutions contained active fuel molecules in addition to the intermetallic nanoparticles (formic acid for PtBi, formic acid and methanol for PtPb), kinetic stabilization effects were observed for E(ulp)=+0.80 V, in a way similar to the response of the bulk materials. It was of great importance to quantitatively explore the change in composition and structure of the intermetallic nanoparticles under active electrochemical control. More importantly, this approach represents a simple, universal, and multifunctional method for the study of multi-element nanoparticles as electrocatalysts. This is, to our knowledge, the first report of nondestructive, quantitative characterization of bimetallic or multi-elemental nanoparticles electrocatalysts under active electrochemical control.     

铂基金属间化合物纳米晶的最新进展:可控合成与电催化应用

铂基金属间化合物纳米晶因其高度有序的结构特点,优异的抗氧化及耐腐蚀性能,作为电极材料被广泛应用于各类电催化反应,目前已有的PtCo金属间化合物纳米晶在燃料电池阴极反应(氧还原反应)中的活性和稳定性均达到了美国能源部(DOE) 2020年的目标。为了进一步提高金属间化合物纳米晶的电催化性能,需要对影响纳米晶电催化性能的因素进行深入研究。本文综述了铂基金属间化合物纳米晶的研究现状,着重介绍了铂基金属间化合物的可控合成策略及其在电催化领域的最新研究进展,分析总结了该领域存在的问题,并展望了其未来发展方向。     

Physical and electrochemical characterizations of microwave-assisted polyol preparation of carbon-supported PtRu nanoparticles

PtRu nanoparticles supported on Vulcan XC-72 carbon and carbon nanotubes were prepared by a microwave-assisted polyol process. The catalysts were characterized by transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy (XPS). The PtRu nanoparticles, which were uniformly dispersed on carbon, were 2-6 nm in diameter. All PtRu/C catalysts prepared as such displayed the characteristic diffraction peaks of a Pt face-centered cubic structure, excepting that the 2theta values were shifted to slightly higher values. XPS analysis revealed that the catalysts contained mostly Pt(0) and Ru(0), with traces of Pt(II), Pt(IV), and Ru(IV). The electro-oxidation of methanol was studied by cyclic voltammetry, linear sweep voltammetry, and chronoamperometry. It was found that both PtRu/C catalysts had high and more durable electrocatalytic activities for methanol oxidation than a comparative Pt/C catalyst. Preliminary data from a direct methanol fuel cell single stack test cell using the Vulcan-carbon-supported PtRu alloy as the anode catalyst showed high power density.     

PtRu catalysts supported on heteropolyacid and chitosan functionalized carbon nanotubes for methanol oxidation reaction of fuel cells

A simple self-assembly approach has been developed to functionalize carbon nanotubes (CNTs) with chitosan (CS) and heteropolyacids (HPAs) of phosphomolybdic acid (H(3)PMo(12)O(40), HPMo) and phosphotungstic acid (H(3)PW(12)O(40), HPW). The non-covalent functionalization method, which introduces homogenous surface functional groups with no detrimental effect on graphene structures of CNTs, can be carried out at room temperature without the use of corrosive acids. The PtRu nanoparticles supported on HPAs-CS-CNTs have a uniform distribution and much smaller size as compared to those of the PtRu nanoparticles supported on conventional acid treated CNTs (PtRu/AO-CNTs). The onset and peak potentials for CO(ad) oxidation on PtRu/HPAs-CS-CNTs catalysts are more negative than those on PtRu/AO-CNTs, indicating that HPAs facilitate the electro-oxidation of CO. The PtRu/HPMo-CS-CNTs catalyst has a higher electrocatalytic activity for methanol oxidation and higher tolerance toward CO poisoning than PtRu/HPW-CS-CNTs. The better electrocatalytic enhancement of HPMo on the PtRu/HPAs-CS-CNTs catalyst is most likely related to the fact that molybdenum-containing HPAs such as HPMo have more labile terminal oxygen to provide additional active oxygen sites while accelerating the CO and methanol oxidation in a similar way to that of Ru in the PtRu binary alloy system.     

In-situ X-ray absorption spectroscopy study of Pt and Ru chemistry during methanol electrooxidation

Methanol electrooxidation in a 0.5 M sulfuric acid electrolyte containing 1.0 M CH3OH was studied on 30% Pt/carbon and 30% PtRu/carbon (Pt/Ru = 1:1) catalysts using X-ray absorption spectroscopy (XAS). Absorption by Pt and Ru was measured at constant photon energy in the near edge region during linear potential sweeps of 10-50 mV/s between 0.01 and 1.36 V vs rhe. The absorption results were used to follow Pt and Ru oxidation and reduction under transient conditions as well as to monitor Ru dissolution. Both catalysts exhibited higher activity for methanol oxidation at high potential following multiple potential cycles. Correlation of XAS data with the potential sweeps indicates that Pt catalysts lose activity at high potentials due to Pt oxidation. The addition of Ru to Pt accelerates the rate of methanol oxidation at all potentials. Ru is more readily oxidized than Pt, but unlike Pt, its oxidation does not result in a decrease in catalytic activity. PtRu/carbon catalysts underwent significant changes during potential cycling due to Ru loss. Similar current density vs potential results were obtained using the same PtRu/carbon catalyst at the same loading in a membrane electrode assembly half cell with only a Nafion (DuPont) solid electrolyte. The results are interpreted in terms of a bifunctional catalyst mechanism in which Pt surface sites serve to chemisorb and dissociate methanol to protons and carbon monoxide, while Ru surface sites activate water and accelerate the oxidation of the chemisorbed CO intermediate. PtRu/carbon catalysts maintain their activity at very high potentials, which is attributed to the ability of the added Ru to keep Pt present in a reduced state, a necessary requirement for methanol chemisorption and dissociation.     

Pd/Pt core–shell nanowire arrays as highly effective electrocatalysts for methanol electrooxidation in direct methanol fuel cells

Highly ordered Pd/Pt–core–shell nanowire arrays (Pd/Pt NWAs) have been prepared by anodized aluminum oxide (AAO) template-electrodeposition and magnetron sputtering methods. Pd/Pt NWA electrode shows a very high electrochemical active surface area and high electrocatalytic activity for the methanol electrooxidation in acid medium for direct methanol fuel cells (DMFCs). The mass specific anodic peak current density is 756.7 mA mg⁻¹ Pt for the methanol oxidation on the Pd/Pt NWA electrode, an increase by a factor of four as compared to conventional E-TEK PtRu/C electrocatalysts. The mechanism of the significant enhancement of the Pd/Pt core/shell NWA nanostructure in the efficiency and electrocatalytic activity of Pt for the methanol electrooxidation in acid medium is discussed.     

Methanol electrooxidation on a colloidal PtRu-alloy fuel-cell catalyst

The electrooxidation of methanol on a novel carbon supported PtRu electrocatalyst produced via colloidal PtRu precursors was investigated by thin-film-electrode (TFE) measurements and compared with commercially available Pt and PtRu catalysts. The PtRu-colloid-based catalyst shows similiar activity towards methanol oxidation as other conventional PtRu catalysts. A comparison with literature data from half-cell measurements at similiar mass-specific current densities clearly demonstrates the high potential of the colloid-based PtRu catalyst for fuel-cell applications.     

Influence of substrate stiffness on cell-substrate interfacial adhesion and spreading: a mechano-chemical coupling model

Highly ordered three dimensionally macroporous carbon spheres (3DMPCS) were successfully prepared against removable colloidal silica crystal bead templates by carbonization of glucose. The unique structural characteristics of the well-developed three dimensionally interconnected macropores were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and nitrogen adsorption. The 3DMPCS have uniform large pore structures with size about 250 nm. Pt nanoparticles were supported on the macroporous carbon spheres by two aqueous impregnation methods, and it was found that the 3DMPCS supported Pt exhibited high electrocatalytic activity for methanol oxidation.     

Dynamics of Electrocatalytic Oxidation of Ethylene Glycol,Methanol and Formic Acid at MWCNT Platform Electrochemically Modified with Pt/Ru Nanoparticles

Comparative electrocatalytic behavior of functionalized multiwalled carbon nanotubes (fMWCNTs) electrodecorated with Pt/Ru nanoparticles towards the oxidation of methanol (MeOH), ethylene glycol (EG) and formic acid (FA) has been investigated. The catalytic current density decreased approximately as MeOH≈EG>FA. Result revealed that BPPGE‐fMWCNT‐Pt/Ru tolerates CO poisoning for FA electrooxidation than when used for the oxidation of the EG or MeOH. Electrochemical impedance spectra are dependent on the oxidation potentials, with equivalent circuit models characteristic of adsorption‐controlled charge transfer kinetics. The results provide important insights into the electrochemical response of these small organic molecules useful in fuel cell technology.     

In situ synthesis of Pt/carbon nanofiber nanocomposites with enhanced electrocatalytic activity toward methanol oxidation

Pt/carbon nanofiber (Pt/CNF) nanocomposites were facilely synthesized by the reduction of hexachloroplatinic acid (H(2)PtCl(6)) using formic acid (HCOOH) in aqueous solution containing electrospun carbon nanofibers at room temperature. The obtained Pt/CNF nanocomposites were characterized by TEM and EDX. The Pt nanoparticles could in situ grow on the surface of CNFs with small particle size, high loading density, and uniform dispersion by adjusting the concentration of H(2)PtCl(6) precursor. The electrocatalytic activities of the Pt/CNF nanocomposites were also studied. These Pt/CNF nanocomposites exhibited higher electrocatalytic activity toward methanol oxidation reaction compared with commercial E-TEK Pt/C catalyst. The results presented may offer a new approach to facilely synthesize direct methanol fuel cells (DMFCs) catalyst with enhanced electrocatalytic activity and low cost.     

金属间化合物电催化剂Pt1Te1/XC-72的制备及其电催化氧化甲醇性能

以氯铂酸和亚碲酸钠为前驱体,采用两步法在醇水体系下得到负载型Pt1Te1金属间化合物前驱体,通过热处理得到负载型金属间化合物电催化剂Pt1Te1/XC-72.采用X射线衍射（XRD）、透射电子显微镜（TEM）、选区电子衍射（SAED）、电子能谱（EDS）和循环伏安方法（CV）对催化剂进行表征.结果表明：所得产物呈有序金属间化合物Pt1Te1结构,平均粒径4.5nm,在碳载体上具有很好的分散性;负载型金属间化合物电催化剂Pt1Te1/XC-72具有较高的电催化氧化甲醇活性,其优秀的催化氧化甲醇活性与Pt形成金属间化合物后所带来的几何及电子结构改变密切相关.     

促进型PtMoSi/C催化剂的制备、表征及电催化活性

采用甲醛还原、H2还原、肼还原三种方法制备了添加硅钼酸的PtMoSi/C阳极催化剂, 并用XRD、XPS和TEM技术对催化剂进行了表征. XRD表明Pt粒子呈立方面心晶态结构, TEM显示PtMoSi/C催化剂粒径小(3−4 nm), 分布窄, 分散性好. XPS分析可知Pt主要以0价, Mo主要以6价, Si主要以4价形态存在于催化剂中. 同时通过循环伏安法和线性扫描法考察了制备方法和添加硅钼酸对催化剂电化学活性的影响. 结果表明, 甲醛还原法制备的PtMoSi/C催化剂(Pt、Mo的原子比为3:1)对甲醇氧化的电化学性能和抗中毒性能优于自制的PtRu/C和E-TEK PtRu/C催化剂, 可能是因为添加硅钼酸可以使活性组分的分散度提高, 从而提高了催化剂的活性和抗毒性能.     

高载量PtNi金属间化合物的氧还原电催化性能

采用改进的多元醇法制备了PtNi(原子比1∶1)质量分数为60%的高金属载量碳载PtNi合金(PtNi/C), 通过在450 ℃下退火处理获得了碳载PtNi金属间化合物氧还原电催化剂. 该催化剂对氧还原的质量比活性和面积比活性分别是商业化Pt/C(JM Pt/C)催化剂的1.66和2.3倍; 并且加速耐久性测试后PtNi金属间化合物催化剂的质量比活性仍与Pt/C的初始性能相当, 耐久性得到了大幅提升. PtNi/C金属间化合物催化剂氧还原活性和稳定性的提高归因于PtNi的有序原子排布结构及催化剂表面零价金属含量的提高.     

碳载Pt和PtRu催化剂的甲醇电氧化比较

利用电化学方法对商用Pt/C和PtRu/C催化剂在酸性介质中的甲醇电氧化进行了比较研究.动电位和恒电位氧化实验结果皆表明PtRu/C比Pt/C对甲醇电催化活性高.PtRu合金的形成不仅改变了催化剂表面对氢的吸附性质,而且使氧化物还原峰电位向阴极方向移动.Ru与甲醇的相互作用为温度活化过程,需要较高的温度.     

Localized Pd overgrowth on cubic Pt nanocrystals for enhanced electrocatalytic oxidation of formic acid

Binary Pt/Pd nanoparticles were synthesized by localized overgrowth of Pd on cubic Pt seeds for the investigation of electrocatalytic formic acid oxidation. The binary particles exhibited much less self-poisoning and a lower activation energy relative to Pt nanocubes, consistent with the single crystal study.     

Bimetallic Cluster Provides a Higher Activity Electrocatalyst for Methanol Oxidation

The cluster complex Pt₂Ru₄(CO)₁₈ was used as a precursor to prepare a 60 wt% 1:2 Pt:Ru nanoparticles on carbon (PtRu/C) for use as an electrocatalyst for methanol oxidation. This bimetallic carbonyl cluster complex was found to provide smaller, more uniform bimetallic nanoparticle that exhibited higher electrocatalytic activity than a 60 wt% 1:1 Pt:Ru commercial catalyst from E-Tek. Using bimetallic cluster precursors simplifies the synthetic procedures by reducing the need for high temperature reduction and assures a more intimate mixing of the two different metals. Transmission electron microscopy (TEM) images of the catalyst obtained from the cluster precursor showed bimetallic nanoparticles having a narrow size range of 2–3 nm that were dispersed uniformly over the surface of the support. Images of the commercial catalyst showed particles 3–4 nm in diameter that tended to agglomerate near the edges of the carbon support particles. Cyclic voltammograms of methanol oxidation from the two catalysts showed significantly higher activity for the cluster-derived catalyst. The onset potential for methanol oxidation for the cluster-derived catalyst was approximately 170 mV lower than that of the commercial catalyst at 100 A/g Pt, and approximately 250 mV lower at 400 A/g Pt. ^* This report is dedicated to Prof. Günter Schmid on the occasion of his 70th birthday.