CuO nanocrystals in thermal decomposition of ammonium perchlorate

CuO nanocrystals of different surface areas were prepared. All samples were characterized by X-ray diffraction, transition electron microscope, thermogravimetry, Brunauer-Emmett-Teller technique, Fourier transform infrared spectroscopy, and Raman spectroscopy. CuO nanocrystals showed a stable monoclinic structure. With increasing surface areas, the surface hydration became significant, which is followed by shifts in infrared frequencies and Raman phonon modes. CuO nanocrystals were explored as an additive to catalytic decomposition of ammonium perchlorate (AP). AP decomposition underwent a two-stage process. Addition of CuO nanocrystals led to a downshift of high-temperature stage towards lower temperatures.     

Self-assembled CuO nanoarchitectures and their catalytic activity in the thermal decomposition of ammonium perchlorate

CuO shuttle-like and flower-like nanocrystals were synthesized through a one-step, low-temperature solution-phase method in the presence of a cation surfactant, hexadecyl trimethyl ammonium bromide. These nanocrystals were studied as an additive for promoting the thermal decomposition of ammonium perchlorate (AP). With the addition of CuO shuttle-like and flower-like nanocrystals, the thermal decomposition temperature of AP decreased. The structure, particle size, and morphology of resulting CuO powders were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Thermogravimetric analysis technique was applied to investigate the thermal decomposition of mixtures of AP and as-prepared CuO nanocrystals.     

Thermal decomposition of ammonium perchlorate based mixture with fullerenes

The effects of fullerenes, including fellerene soot (FS), extracted fullerene soot (EFS) and pure C₆₀ on the thermal decomposition of ammonium perchlorate (AP) compared with traditional carbon black (CB) catalyst has been studied by employing thermogravimetry (TG), differential thermal analysis (DTA), infrared spectroscopy (IR) and ignition temperature experiments. The results showed that the addition of CB and FS to AP reduced the activation energy as well as the temperature at maximum decomposition rate, but that of EFS and pure C₆₀ had little effect on the thermal decomposition of AP, and among all catalysts, FS was the best one.     

直形碳纳米管、分叉碳纳米管负载纳米NiO及其对高氯酸铵热分解的影响

采用射流进样催化裂解法制备了直形碳纳米管(CNTs)、分叉碳纳米管, 分别以二者为载体, 用化学沉积法制备了负载纳米NiO的复合粒子, 并研究了纳米NiO和CNTs的单一纳米粒子、简单混合物、复合物对高氯酸铵(AP)热分解的催化性能, 对催化效果的差异作了初步探讨. 结果表明: NiO/直形CNTs和NiO/分叉CNTs复合粒子比表面积大, 表面负载层的纳米NiO结晶好、粒子均匀、粒径小、分散性好. 复合粒子对AP热分解的催化效果比单一纳米粒子和简单混合物好, 其中NiO/分叉CNTs复合粒子催化效果最好, 使AP高温分解峰温降低了94.6 ℃, 使表观分解热增加了819 J/g. CNTs的载体支撑作用, 可防止NiO纳米粒子的团聚, 增大比表面积, 增加反应活性中心, 增加催化效果, 载体分叉CNTs的枝杈形结构, 有利于纳米NiO/分叉CNTs复合粒子催化性能的提高.     

Preparation of NdCrO3 nanoparticles and their catalytic activity in the thermal decomposition of ammonium perchlorate by DSC/TG-MS

Orthorhombic structural perovskite NdCrO₃ nanocrystals with size of 60 nm were prepared by microemulsion method, and characterized by XRD, TEM, HRTEM, SEM, EDS and BET. The catalytic effect of the NdCrO₃ for thermal decomposition of ammonium perchlorate (AP) was investigated by DSC and TG-MS. The results revealed that the NdCrO₃ nanoparticles had effective catalysis on the thermal decomposition of AP. Adding 2% of NdCrO₃ nanoparticles to AP decreased the temperature of thermal decomposition by 87° and increased the heat of decomposition from 590 to 1073 J g⁻¹. Gaseous products of thermal decomposition of AP were NH₃, H₂O, O₂, HCl, N₂O, NO, NO₂ and Cl₂. The mechanism of catalytic action was based on the presence of superoxide ion O₂ ⁻ on the surface of NdCrO₃, and the difference of thermal decomposition of AP with 2% of NdCrO₃ and pure AP was mainly caused by the different extent of oxidation of ammonium.     

MOF-derived hollow NiO–ZnO composite micropolyhedra and their application in catalytic thermal decomposition of ammonium perchlorate

Ni(II)-doped Zn-based coordination polymer particles (Ni(II)-doped Zn-CPPs) with controllable shape and size were successfully synthesized by solvothermal method, which further transformed to porous ZnO–NiO composite micropolyhedra without significant alterations in shape by calcination in air. Those products were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), infrared spectroscopy (IR) and gas adsorption measurements. The catalytic activity of ZnO–NiO composites for the thermal decomposition of ammonium perchlorate (AP) was investigated. The result shows that all ZnO–NiO composites efficiently catalyzed the thermal decomposition of AP, and NiO–ZnO composite hollow octahedrons have the highest catalytic efficiency compared with that of most materials reported to now, indicating that porous ZnO–NiO composite micropolyhedra could be a promising candidate material for application in AP-based propellant.     

Room temperature solution-phase synthesis of flower-like nanostructures of [Ni3(BTC)2·12H2O] and their conversion to porous NiO

Hierarchical flower-like architectures of[Ni₃（BTC）₂·12H₂O]（BTC³=benzene-1,3,5-tricarboxylate） were successfully prepared by a simple solution-phase method under mild conditions without any template or surfactant.Phase-pure porous NiO nanocrystals were obtained by annealing the Ni-BTC complex without significant alteration in morphology.The product was characterized by X-ray diffraction techniques,field-emission scanning electron microscopy（FESEM）.transmission electron microscopy（TEM） and high-resolution TEM（HRTEM）.The catalytic effect of the NiO product was investigated on the thermal decomposition of ammonium perchlorate（AP） and it was found that the annealed NiO product has higher catalytic activity than the commercial NiO.     

The effect of specific surface area of TiO<Subscript>2</Subscript> on the thermal decomposition of ammonium perchlorate

The thermal decomposition of ammonium perchlorate (AP) is considered to be the first step in the combustion of AP-based composite propellants. In this report, the effect of the specific surface area of titanium oxide (TiO₂) catalysts on the thermal decomposition characteristics of AP was examined with a series of thermal analysis experiments. It was clear that the thermal decomposition temperature of AP decreased when the specific surface area of TiO₂ increased. It was also possible that TiO₂ influences the frequency factor of AP decomposition because there was no observable effect on the activation energy.     

CuO nanoparticles supported on three‐dimensional nitrogen‐doped graphene as a promising catalyst for thermal decomposition of ammonium perchlorate

In the present work, CuO nanoparticles grown on three‐dimensional nitrogen‐doped graphene‐based frameworks (CuO@3D‐(N)GFs) were synthesized using a two‐step method. After the synthesis of three‐dimensional nitrogen‐doped graphene, CuO nanoparticles were deposited on it, by adding cupric acetate followed by thermal treatment. Different analysis methods were used to characterize the products. The as‐prepared nanocomposite was used as a promising catalyst for thermal decomposition of ammonium perchlorate (AP) as one of the most common oxidizer in composite propellants. Differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA) techniques were used to investigate the thermal decomposition of ammonium perchlorate. According to the DSC/TGA, high temperature decomposition of AP decreased to 111 °C in the presence of 4% CuO@3D‐(N)GFs and the total heat release (ΔH) from decomposition of AP increased to 1893 J g^?1 which is much more than 590 J g^?1 for pure AP.     

Multichanneled hierarchical porous nanocomposite CuO/carbonized butterfly wing and its excellent catalytic performance for thermal decomposition of ammonium perchlorate

To meet the requirement of generating more apparent specific heat release at lower temperatures for ammonium perchlorate (AP)-based composite solid propellants, the development of high-performance catalysts for improving the thermal decomposition properties of AP still remains essential and challenging. Herein, a novel catalyst, multichanneled hierarchical porous nanocomposite of CuO and carbonized butterfly wing (CuO/CBW), has been prepared through an in-situ reaction on original butterfly wing scales. Owing to the high active surface area and the good electrical and thermal conductivity, as well as the synergistic effect of CuO nanoparticles (20–25 nm) and CBW, CuO/CBW nanocomposite exhibits excellent catalytic activity for AP thermal decomposition in reducing the high-temperature decomposition temperature by 88.3°C, lowering the apparent activation energy from 190.0 to 103.1 kJ mol⁻¹ and increasing the heat release from 255 to 1841 J g⁻¹.     

Improvement of thermal decomposition properties of ammonium perchlorate particles using some polymer coating agents

This research aimed to investigate the optimum conditions for modification of thermal decomposition properties of ammonium perchlorate (AP) particles through microencapsulation techniques. A solvent/non-solvent method has been used to perform microencapsulation of AP particles with some polymer-coating agents such as viton A and nitrocellulose (NC). Differential scanning calorimetry, thermogravimetry, and scanning electron microscopy have been exploited to investigate the thermal properties, heat of decomposition, and coating morphology of pure and coated samples. The preliminary results revealed that AP microparticle could be effectively coated with both NC and viton, but the latter significantly and unfavorably attenuated heat of decomposition of AP so NC was chosen as an appropriate coating agent for modification of thermal properties of AP. The thermal analysis of NC-coated samples, prepared at optimized coating conditions, showed that its first stage decomposition temperature increases about 12 °C with respect to uncoated sample and reaches to 305 °C. Also, the apparent activation energy (E), ΔG ^≠, ΔH ^≠, and ΔS ^≠ of the decomposition processes of the pure and coated AP particles at the optimum conditions were obtained by non-isothermal methods that proposed by ASTM and Ozawa. Finally, the results of this investigation showed that microencapsulation of AP particles with fibrous NC enhance its heat of decomposition (~120 J g^?1) with no obvious effect on kinetic parameters and thermal decomposition temperature.     

钛酸锌的制备及其对高氯酸铵热分解的催化性能

ZnTiO₃ nanocrystals were prepared by sol-gel method, using Zn(NO₃)₂ and Ti(C₄H₉O)₄ in the topic. The as-prepared ZnTiO₃ nanocrystals were characterized by XRD, FTIR and TEM, and the catalytic performance of ZnTiO₃ nanocrystals of different contents for the ammonium perchlorate(AP)decomposition was investigated by thermal analysis. The results indicate that ZnTiO₃ with pure cube structure can be synthesized at 600 ℃ by this procedure,which was spheroid with particle size of about 60~100 nm. The results expressed that the low temperature decomposition peaks of AP is advanced by 17 ℃ and the high temperature decomposition peaks of AP is advanced by 24 ℃ when adding 5% nanoparticle ZnTiO₃ powder. The catalytic effects of ZnTiO₃ powders on the high temperature decomposition of AP are less than that of nanometer metal powders, but all the micron metal powders decrease the low decomposition temperature of AP.     

Thermal decomposition properties of double-base propellant and ammonium perchlorate

The thermal decomposition properties and the heat of combustion (ΔH) of samples with different ammonium perchlorate (AP)/double base propellant (DB) mass ratios under argon atmosphere were studied by the thermogravimetry–differential scanning calorimetry–mass spectrometry–Fourier transform infrared spectroscopy (TG–DSC–MS–FTIR) and automatic calorimeter method. The results show that decomposition process of AP/DB samples in negative and zero oxygen balance (OB) is different from that in positive OB. With the increasing of AP in the AP/DB samples, the decomposition of the samples becomes more and more severe. When the OB of the samples is positive, the phenomenon of deflagration or explosion could be observed in the decomposition process. The sample with OB = 0 has the greatest heat of combustion.     

纳米NdCoO3催化高氯酸铵热分解的DSC/TG-MS研究

采用微乳液法制备了立方晶系的NdCoO3纳米晶.利用DSC/TG-MS研究了NdCoO3对AP热分解的催化作用.结果表明,在NdCoO3的催化作用下,AP的热分解反应峰值温度下降了113℃,表观分解反应热从655 J·g-1增加到1 363 J·g-1,分解的气相产物主要有NH3,H2O,O2,HCl,N2O,NO,NO2和Cl2.在金属氧化物表面吸附生成超氧化离子(O2-)和氧离子(O-,O2-),这是加速AP分解反应的主要原因.加入NdCoO3催化AP热分解,由于对氨的氧化深度不同而导致分解放热量的增加.     

Pure CuCr2O4 nanoparticles: Synthesis,characterization and their morphological and size effects on the catalytic thermal decomposition of ammonium perchlorate

In the present paper a pure phase of the copper chromite spinel nanoparticles (CuCr₂O₄ SNPs) were synthesized via the sol–gel route using citric acid as a complexing agent. Then, the CuCr₂O₄ SNPs has been characterized by field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). In the next step, with the addition of Cu–Cr–O nanoparticles (NPs), the effects of different parameters such as Cu–Cr–O particle size and the Cu/Cr molar ratios on the thermal behavior of Cu–Cr–O NPs + AP (ammonium perchlorate) mixtures were investigated. As such, the catalytic effect of the Cu–Cr–O NPs for thermal decomposition of AP was evaluated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA/DSC results showed that the samples with different morphologies exhibited different catalytic activity in different stages of thermal decomposition of AP. Also, in the presence of Cu–Cr–O nanocatalysts, all of the exothermic peaks of AP shifted to a lower temperature, indicating the thermal decomposition of AP was enhanced. Moreover, the heat released (ΔH) in the presence of Cu–Cr–O nanocatalysts was increased to 1490 J g⁻¹.     

Nature of catalytic activities of CoO nanocrystals in thermal decomposition of ammonium perchlorate

This work addresses the chemical nature of the catalytic activity of X-ray "pure" CoO nanocrystals. All samples were prepared by a solvothermal reaction route. X-ray diffraction indicates the formation of CoO in a cubic rock-salt structure, while infrared spectra and magnetic measurements demonstrate the coexistence of CoO and Co 3O 4. Therefore, X-ray "pure" CoO nanocrystals are a unique composite structure with a CoO core surrounded by an extremely thin Co 3O 4 surface layer, which is likely a consequence of the surface passivation of CoO nanocrystals from the air oxidation at room temperature. The CoO core shows a particle size of 22 or 280 nm, depending on the types of the precursors used. This composite nanostructure was initiated as a catalytic additive to promote the thermal decomposition of ammonium perchlorate (AP). Our preliminary investigations indicate that the maximum decomposition temperature of AP is significantly reduced in the presence of CoO/Co 3O 4 composite nanocrystals and that the maximum decomposition peak shifts toward lower temperatures as the loading amount of the composite nanocrystals increases. These findings are different from the literature reports when using many nanoscale oxide additives. Finally, the decomposition heat for the low-temperature decomposition stages of AP was calculated and correlated to the chemical nature of the CoO/Co 3O 4 composite nanostructures.     

Effect of ammonia on the thermal decomposition of orthorhombic and cubic ammonium perchlorate

The inhibiting effect of ammonia vapours on the kinetics of the thermal decomposition of ammonium perchlorate(AP) in the temperature range 215–270°C has been investigated. An initial ammonia pressure of about 200 Torr is necessary for the practically full suppression of the decomposition of the orthorhombic crystals at temperatures close to the point of AP polymorphic transformation (240°C). With the cubic crystals, 0.5 Torr is the corresponding pressure required. In the case of complete inhibition of the decomposition in the presence of ammonia, AP crystals become yellowish. The activation energy of decomposition of the orthorhombic modification is 29 ± 0.6 kcal mole^?1 in the absence of ammonia, and 38 ± 1.1 kcal mole^?1 under ammonia vapour pressure of 6.5 Torr. A kinetic analysis of the traditional proton model of AP decomposition has been made showing that the increase of the activation energy in the presence of ammonia may be derived from this model.     

Synthesis of dihydropyrazole‐bridged dinuclear ferrocenyl derivatives and their catalytic effect on thermal decomposition of ammonium perchlorate

Dihydropyrazole‐bridged dinuclear ferrocenyl derivatives (3a–3c) have been synthesized by the reaction of 1,3‐diferrocenyl‐2‐propen‐1‐on (1) with hydrazine, then acylation with acyl chloride directly. The structures were determined by mass spectrometry, IR and ¹H NMR spectroscopy. The compound 3c was characterized by single‐crystal X‐ray analyses. It was found that compounds 3a–3c have significant catalytic effect on the decomposition of ammonium perchlorate (AP). Compared with the thermal decomposition of pure AP, adding 3a, 3b and 3c in AP decreases its decomposition temperature by 78.8, 74.3 and 57.1 °C, respectively. Copyright © 2011 John Wiley & Sons, Ltd.     

Differential thermal analysis and thermogravimetry of ammonium perchlorate at pressures up to 51 ATM

The thermal decomposition of pure ammonium perchlorate (AP)was investigated in various gaseous atmospheres at pressures up to 51 atm, using a technique of thermal analysis. It is concluded that the first and second stage decompositions of AP in an atmosphere of oxygen or nitrogen are appreciably accelerated as the pressure is increased. Platinum has a catalytic effect in the high-temperature decomposition and suppresses the sublimation of AP at high temperature ranges in helium atmosphere even at 1 atm. The reaction heat for the high-temperature decomposition of AP in the platinum cell was calculated from the peak temperatures of DTA curves at various pressures to be 77.9 kcal mol^?1. The activation energies of the sublimation in helium at 1 atm and of the high-temperature decomposition in the platinum cell at various pressures of helium have also been obtained, giving similar values of 23–25 kcal mol^?1.     

A facile synthesis of boron nanostructures and investigation of their catalytic activity for thermal decomposition of ammonium perchlorate particles

In this research, ultrasound irradiation as a simple method was used to produce boron nanostructures. Reaction conditions such as boron concentration and sonication time show important roles in the size, morphology and growth process of the final products. The boron nanostructures (nanoparticles and nanorods) were characterized by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, small-angle X-ray scattering and inductively coupled plasma atomic emission spectroscopy techniques. Primary evaluation of results showed that nanoparticles and nanorods of boron successfully have been prepared with 25–40 and 50–100 nm average particle size, respectively. These nanostructures (nanoparticles and nanorods) were studied as an additive for promoting the thermal decomposition of ammonium perchlorate (AP) particles. Thermochemical decomposition behaviors of treated samples were characterized by thermal gravimetric analysis and differential scanning calorimetry techniques. Also, the kinetic parameters of thermal decomposition processes of pure and treated samples were obtained by nonisothermal methods proposed by Kissinger and Ozawa. However, boron nanoparticles with the smallest average particle size (25–40 nm) have the most significant catalytic effect including the decrease in decomposition temperature of AP + B nanocomposite by 100 °C, increase in the heat of decomposition from 580 to 1354 J g^?1 and decrease in activation energy from 207 to 110 kJ mol^?1.