Studies on epoxy resins cured by cationic latent thermal catalysts: The effect of the catalysts on the thermal,rheological, and mechanical properties

To investigate the effect of catalysts on the thermal, rheological, and mechanical properties of an epoxy system, a resin based on diglycidyl ether of bisphenol‐A (DGEBA) was cured by two cationic latent thermal catalysts, N‐benzylpyrazinium hexafluoroantimonate (BPH) and N‐benzylquinoxalinium hexafluoroantimonate (BQH). Differential scanning calorimetry was used for the thermal characterization of the epoxy systems. Near‐infrared spectroscopy was employed to examine the cure reaction between the DGEBA and the latent thermal catalysts used. The rheological properties of the blend systems were investigated under an isothermal condition with a rheometer. To characterize the mechanical properties of the systems, flexure, fracture toughness (K_IC), and impact tests were performed. The phase morphology was studied with scanning electron microscopy of the fractured surfaces of mechanical test samples. The conversion and cure activation energy of the DGEBA/BQH system were higher than those of the DGEBA/BPH system. The crosslinking activation energy showed a result similar to that obtained from the cure kinetics of the blend systems. The flexure strength, K_IC, and impact properties of the DGEBA/BQH system were also superior to those of the DGEBA/BPH system. This was a result of the substituted benzene group of the BQH catalyst, which increased the crosslink density and structural stability of the epoxy system studied. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 187–195, 2001     

Near‐infrared spectroscopic studies on the cure behaviors of the CAE/DGEBA blend system initiated by a thermal latent catalyst

The latent properties and cure behaviors of an epoxy blend system based on cycloaliphatic epoxy (CAE) and diglycidyl ether of bisphenol A (DGEBA) epoxy containing N‐benzylpyrazinium hexafluoroantimonate (BPH) as a thermal latent initiator were investigated with near‐infrared (N‐IR) spectroscopy. The assignments of the latent properties and cure kinetics were performed by the measurements of the N‐IR reflectance for epoxide and hydroxyl functional groups at different temperatures and compositions. As a result, this system showed more than one type of reaction, and BPH was an excellent thermal latent catalyst without any coinitiator. The cure behaviors were identified by the changes in the absorption intensity of the hydroxyl groups at 7100 cm⁻¹ with different composition ratios. Moreover, characteristic N‐IR band assignments were used to evaluate the reactive kinetics and were shown to be an appropriate method for studying the cure behaviors of the CAE/DGEBA blend system containing a thermal latent catalyst. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 326–331, 2001     

Cure behavior of diglycidylether of bisphenol A/trimethylolpropane triglycidylether epoxy blends initiated by thermal latent catalyst

Cure behaviors of diglycidylether of bisphenol A (DGEBA)/trimethylolpropane triglycidylether (TMP) epoxy blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate (BPH) as a cationic latent catalyst were investigated using DSC and rheometer. This system showed more than one type of reaction and BPH could be excellent thermal latent catalyst without any co‐initiator. The cure activation energy (E_a) obtained from Kissinger method using dynamic DSC data was higher in DGEBA/TMP mixtures than in pure DGEBA. Rheological properties of the blend system were investigated under isothermal condition using a rheometer. The gel time was obtained from the analysis of storage modulus (G′), loss modulus (G″) and damping factor (tanδ). The crosslinking activation energy (E_c) was also determined from the Arrhenius equation based on the gel time and curing temperature. As a result, the crosslinking activation energy showed a similar behavior with that obtained from Kissinger method. And the gel time decreased with increasing TMP content, which could be resulted from increasing the activated sites by trifunctional epoxide groups and decreasing the viscosity of DGEBA/TMP epoxy blend in the presence of TMP. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2114–2123, 2000     

Effect of the substituted benzene group on thermal and mechanical properties of epoxy resins initiated by cationic latent catalysts

Epoxy resins (DGEBA) were cured by cationic latent thermal catalysts, that is, N‐benzylpyrazinium hexafluoroantimonate (BPH) and N‐benzylquinoxalinium hexafluoroantimonate (BQH) to investigate the effect of substituted benzene group on cure kinetics and mechanical properties of epoxy system. Differential scanning calorimetry (DSC) was undertaken for activation energy of the system. It was also characterized in terms of flexural, fracture toughness, and Izod impact strengths for the mechanical tests. As a result, the cure reaction of both epoxy systems resulted in an autocatalytic kinetic mechanism accelerated by hydroxyl groups. Also, the conversion and cure activation energy of the DGEBA/BQH system were higher than those of DGEBA/BPH system. The mechanical properties of the DGEBA/BQH system were also superior to those of the DGEBA/BPH system, as well as the morphology. This was probably due to the consequence of the effect of the substituted benzene group of the BQH catalyst, resulting in increasing the crosslinking density and structural stability in the epoxy system studied. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2419–2429, 2004     

Curing reaction of biphenyl epoxy resin with different phenolic functional hardeners

The investigation of cure kinetics and relationships between glass transition temperature and conversion of biphenyl epoxy resin (4,4′-diglycidyloxy-3,3′,5,5′-tetramethyl biphenyl) with different phenolic hardeners was performed by differential scanning calorimeter using an isothermal approach over the temperature range 120–150°C. All kinetic parameters of the curing reaction including the reaction order, activation energy, and rate constant were calculated and reported. The results indicate that the curing reaction of formulations using xylok and dicyclopentadiene type phenolic resins (DCPDP) as hardeners proceeds through a first-order kinetic mechanism, whereas the curing reaction of formulations using phenol novolac as a hardener goes through an autocatalytic kinetic mechanism. The differences of curing reaction with the change of hardener in biphenyl epoxy resin systems were explained with the relationships between T_g and reaction conversion using the DiBenedetto equation. A detailed cure mechanism in biphenyl-type epoxy resin with the different hardeners has been suggested. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 773–783, 1998     

Cationic cure of epoxy resin initiated by methylanilinium salts as a latent thermal initiator

The effect of the novel N‐crotyl‐N,N‐dimethyl‐4‐methylanilinium hexafluroantimonate (CMH) initiator on cure kinetics and rheological properties of diglycidylether of bisphenol A (DGEBA) epoxy cationic system was investigated. From DSC measurements of the DGEBA/CMH system, it was found that this system exhibited excellent thermal latent characteristics at a given temperature and revealed complex cure behavior as indicated by multiple exotherms. The conversion and conversion rate of the DGEBA/CMH system increased with increasing the concentration of initiator, attributed to the high activity of CMH. Viscoelastic properties during gel formation of DGEBA initiated by CMH were investigated by rheological techniques under isothermal conditions. The gel time obtained from the modulus crossover point t(G′) = G″ was affected by a high curing temperature and the concentration of CMH, resulting in a high degree of network formation in cationic polymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2397–2406, 2001     

Flame‐retardant epoxy resins from o‐cresol novolac epoxy cured with a phosphorus‐containing aralkyl novolac

A novel phosphorus‐containing aralkyl novolac (Ar‐DOPO‐N) was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) first with terephthaldicarboxaldehyde and subsequently with phenol. The chemical structures of the synthesized compounds were characterized with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. Ar‐DOPO‐N blended with phenol formaldehyde novolac was used as a curing agent for o‐cresol formaldehyde novolac epoxy, resulting in cured epoxy resins with various phosphorus contents. The epoxy resins exhibited high glass‐transition temperatures (159–177 °C), good thermal stability (>320 °C), and retardation on thermal degradation rates. High char yields and high limited oxygen indices (26–32.5) were observed, indicating the resins' good flame retardance. Using a melamine‐modified phenol formaldehyde novolac to replace phenol formaldehyde novolac in the curing composition further enhanced the cured epoxy resins' glass‐transition temperatures (160–186 °C) and limited oxygen index values (28–33.5). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2329–2339, 2002     

Facile preparation of novel epoxy curing agents and their high‐performance thermosets

Two flame‐retardant epoxy curing agents, 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐yl‐tris(4‐hydroxyphenyl)methane (1) and 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐yl‐ (4‐aminophenyl)‐bis(4‐hydroxyphenyl)methane (2), were prepared by a facile, economic, one‐pot procedure. The structures of the curing agents were confirmed by IR, high‐resolution mass, 1‐D, and 2‐D NMR spectra. A reaction mechanism was proposed for the preparation, and the effect of electron withdrawing/donating effects on the stabilization of the carbocation was discussed. (1‐2) served as curing agents for diglycidyl ether of bisphenol A (DGEBA), dicyclopentadiene epoxy (HP‐7200), and cresol novolac epoxy (CNE). Properties such as glass transition temperature, coefficient of thermal expansion, thermal decomposition temperature, and flame retardancy of the resulting epoxy thermosets were evaluated. The resulting epoxy thermosets show high T_g, low thermal expansion, moderate thermostability, and excellent flame retardancy. The bulky biphenylene phosphinate pendant makes polymer chains difficult to rotate, explaining the high T_g and low thermal expansion characteristic. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7898–7912, 2008     

Thermal stability and toughening of epoxy resin with polysulfone resin

The cure behavior, thermal stability, and mechanical properties of diglycidylether of bisphenol A (DGEBA)/polysulfone (PSF) blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate as a cationic latent catalyst were investigated. The DGEBA/PSF content was varied within 100/0–100/40 wt %. Latent properties were studied through the measurement of the conversion as a function of the curing temperature, and the cure activation energy (E_a) was studied by the Kissinger method with a dynamic differential scanning calorimetry analysis. The thermal stabilities, largely based on the integral procedural decomposition temperature (IPDT) and decomposed activation energy (E_t), were investigated by the measurement of thermogravimetric analysis. For the mechanical properties of the casting specimens, the critical stress intensity factor (K_IC) test was performed, and their fractured surfaces were examined with scanning electron microscopy. E_a, IPDT, E_t, and K_IC increased with PSF increasing in the neat epoxy resin up to 30 wt %. However, there was a marginal decrease in the blend system in both the thermal and mechanical properties due to the phase separation between DGEBA and PSF. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 121–128, 2001     

Novel,environmentally friendly crosslinking system of an epoxy using an amino acid: Tryptophan‐cured diglycidyl ether of bisphenol A epoxy

Tryptophan, an amino acid, has been used as a novel, environmentally friendly curing agent instead of toxic curing agents to crosslink the diglycidyl ether of bisphenol A (DGEBA) epoxy resin. The curing reaction of tryptophan/DGEBA mixtures of different ratios and the effect of the imidazole catalyst on the reaction have been evaluated. The optimum reaction ratio of DGEBA to tryptophan has been determined to be 3:1 with 1 wt % catalyst, and the curing mechanism of the novel reaction system has been studied and elucidated. In situ Fourier transform infrared spectra indicate that with the extraction of a hydrogen from NH₃⁺ in zwitterions from tryptophan, the formed nucleophilic primary amine and carboxylate anions of the tryptophan can readily participate in the ring‐opening reaction with epoxy. The secondary amine, formed from the primary amine, can further participate in the ring‐opening reaction with epoxy and form the crosslinked network. The crosslinked structure exhibits a reasonably high glass‐transition temperature and thermal stability. A catalyst‐initiated chain reaction mechanism is proposed for the curing reaction of the epoxy with zwitterion amino acid hardeners. The replacement of toxic curing agents with this novel, environmentally friendly curing agent is an important step toward a next‐generation green electronics industry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 181–190, 2007     

Epoxy resin/poly(ϵ‐caprolactone) blends cured with 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane. I. Miscibility and crystallization kinetics

Crystalline thermosetting blends composed of 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP)‐cured epoxy resin (ER) and poly(?‐caprolactone) (PCL) were prepared via the in situ curing reaction of epoxy monomers in the presence of PCL, which started from initially homogeneous mixtures of diglycidyl ether of bisphenol A (DGEBA), BAPP, and PCL. The miscibility of the blends after and before the curing reaction was established with differential scanning calorimetry and dynamic mechanical analysis. Single and composition‐dependent glass‐transition temperatures (T_g's) were observed in the entire blend composition after and before the crosslinking reaction. The experimental T_g's were in good agreement with the prediction by the Fox and Gordon–Taylor equations. The curing reaction caused a considerable increase in the overall crystallization rate and dramatically influenced the mechanism of nucleation and the growth of the PCL crystals. The equilibrium melting point depression was observed for the blends. An analysis of the kinetic data according to the Hoffman–Lauritzen crystallization kinetic theory showed that with an increasing amorphous content, the surface energy of the extremity surfaces increased dramatically for DGEBA/PCL blends but decreased for ER/PCL blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1085–1098, 2003     

Rheokinetic cure characterization of epoxy–anhydride polymer system with shape memory characteristics

An epoxy resin capable of exhibiting shape memory property was derived by curing diglycidyl ether of bisphenol A (DGEBA) with a blend of carboxy telechelic poly(tetramethyleneoxide) (PTAC) and pyromellitic dianhydride (PMDA). The cure kinetics of DGEBA/PTAC/PMDA blend of varying compositions was investigated using isothermal rheological analysis. The overall reaction conformed to a second-order autocatalytic model. The kinetic parameters including reaction order, kinetic constants and activation energy were determined. The results showed that increase of PTAC decreased the overall activation energy and frequency factor of the cure reaction. This effect resulted in a diminution of the overall rate of curing. The catalysis by PTAC has its origin from the activation of epoxy groups by the protons of the COOH groups. The autocatalysis was caused by the COOH groups generated by the reaction of alcohol groups with anhydride. The activation energy for the autocatalysis was more than that for the primary reaction as the COOH groups responsible for autocatalysis were generated on a sterically hindered polymer backbone. The kinetics helped generate a master equation conforming to second-order autocatalytic model that could predict the cure profile of a specified resin system at a given temperature, leading to cure optimization.     

Novel quaternary ammonium borates as latent catalysts for epoxy–phenolic resins

Novel tetrabutylammonium tetrakis(substituted benzoyloxy)borate salts ( 1a – 1d ) were synthesized by the reaction of tetrabutylammonium tetraphenylborate and corresponding substituted benzoic acids. Polyaddition reactions of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐bisphenol F (44BPF) or bisphenol F (BPF‐D) with the ammonium borates were investigated as model reactions of epoxy/phenol–novolac resin systems with respect to the thermal latency and storage stability of the catalyst. The polyaddition of DGEBA/44BPF with the ammonium borates in diglyme at 150 °C for 6 h proceeded up to 84–94% conversions and gave polymers with number‐average molecular weights of 3750–5750, whereas the polyaddition at 80 °C for 6 h gave less than 9% conversions. The catalytic activity of ammonium borates 1a – 1d depended on the substituent of the phenyl group of the borates, and the order of activity was 1b (p‐OMe) > 1a (? H) > 1c (p‐NO₂) > 1d [3,5‐(NO₂)₂]. The ammonium borate catalyst with the substituent that yielded lower acidity of the corresponding substituted benzoic acid tended to reveal higher activity. In comparison with tetrabutylammonium bromide (TBAB) as a conventional ammonium salt, 1a – 1d revealed better thermal latency. The storage stability of DGEBA/BPF‐D with the ammonium borate catalysts in bulk at 40 °C was better than that with TBAB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2689–2701, 2002     

Effect of nanosilica on the kinetics of cure reaction and thermal degradation of epoxy resin

Nanocomposites from nanoscale silica particles(NS),diglycidylether of bisphenol-A based epoxy(DGEBA),and 3,5-diamino-N-(4-(quinolin-8-yloxy) phenyl) benzamide(DQPB) as curing agent were obtained from direct blending of these materials.The effect of nanosilica(NS) particles as catalyst on the cure reaction of DGEBA/DQPB system was studied by using non-isothermal DSC technique.The activation energy(E_a) was obtained by using Kissinger and Ozawa equations. The E_a value of curing of DGEBA/DQPB/10%NS system showed a decrease of about 10 kJ/mol indicating the catalytic effect of NS particles on the cure reaction.The E_a values of thermal degradation of the cured samples of both systems were 148 kJ/mol and 160 kJ/mol,respectively.The addition of 10%of NS to the curing mixture did not have much effect on the initial decomposition temperature(T_i) but increased the char residues from 20%to 28%at 650℃.     

Evaluating a four-directional benzene-centered aliphatic polyamine curing agent for epoxy resins

A four-directional benzene-centered aliphatic polyamine, MXBDP, with high functionality and low volatility, is used to cure epoxy resin (DGEBA). Herein we originally report the isothermal cure kinetics and dynamic mechanical properties of DGEBA/MXBDP. Differential scanning calorimetry confirms that MXDBP is more reactive than commercial linear metaxylenediamine and branched Jeffamine T-403 and the isothermal curing reaction is autocatalytic. The Kamal model is found to be able to well describe the curing rate up to the onset of diffusion control, and the excellent match over the whole conversion range is achieved using the extended Kamal model. Interestingly, the isoconversional kinetic analysis indicates that the effective reaction activation energy (E _α ) changes substantially with conversion, and ultimately decreases to a very small value (<10 kJ mol^?1) because of the diffusion-controlled reaction kinetics. Then, dynamic mechanical analysis reveals that DGEBA/MXBDP exhibits the higher α- and β-relaxation temperatures and the much higher crosslink density than DGEBA/metaxylenediamine. Our experiment results support that MXBDP has the high reactivity and improved thermal resistance in combination with the advantages of the high functionality, low volatility and decreased CO₂ absorption. Therefore, MXBDP may be especially suitable for room temperature-cure epoxy coatings and adhesives.     

High melting thermoplastic/epoxy resin blends: Influence of the curing reaction on the crystallization and melting behavior

The influence of the cure process and the resulting reaction‐induced phase separation (RIPS) on the crystallization and melting behavior of polyoxymethylene (POM) in epoxy resin diglycidylether of bisphenol A (DGEBA) blends has been studied at different cure temperatures (180 and 145 °C). The crystallization and melting behavior of POM was studied with DSC and the simultaneous blend morphology changes were studied using OM. At first, the influence of the epoxy monomer on the dynamically crystallized POM was investigated. Secondly, a cure temperature above the melting point of POM (T_cure = 180 °C) was applied for blends with curing agent to study the influence of resulting phase morphology types on the crystallization behavior of POM in the epoxy blends. Large differences between particle/matrix and phase‐inverted structures have been observed. Thirdly, the cure temperature was lowered below the melting temperature of POM, inducing isothermal crystallization prior to RIPS. As a consequence, a distinction was made between dynamically and isothermally crystallized POM. Concerning the dynamically crystallized material, a clear difference could be made between the material crystallized in the homogeneous sample and that crystallized in the phase‐separated structures. The isothermally crystallized POM was to a large extent influenced by the conversion degree of the epoxy resin. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2456–2469, 2007     

Nonaqueous synthesis of nanosilica in epoxy resin matrix and thermal properties of their cured nanocomposites

Nonaqueous synthesis of nanosilica in diglycidyl ether of bisphenol‐A epoxy (DGEBA) resin has been successfully achieved in this study by reacting tetraethoxysilane (TEOS) directly with DGEBA epoxy matrix, at 80 °C for 4 h under the catalysis of boron trifluoride monoethylamine (BF₃MEA). BF₃MEA was proved to be an effective catalyst for the formation of nanosilica in DGEBA epoxy under thermal heating process. FTIR and ²⁹Si NMR spectra have been used to characterize the structures of nanosilica obtained from this direct thermal synthetic process. The morphology of the nanosilica synthesized in epoxy matrix has also been analyzed by TEM and SEM studies. The effects of both the concentration of BF₃MEA catalyst and amount of TEOS on the diameters of nanosilica in the DGEBA epoxy resin have been discussed in this study. From the DSC analysis, it was found that the nanosilica containing epoxy exhibited the same curing profile as pure epoxy resin, during the curing reaction with 4,4′‐diaminodiphenysulfone (DDS). The thermal‐cured epoxy–nanosilica composites from 40% of TEOS exhibited high glass transition temperature of 221 °C, which was almost 50 °C higher than that of pure DGEBA–DDS–BF₃MEA‐cured resin network. Almost 60 °C increase in thermal degradation temperature has been observed during the TGA of the DDS‐cured epoxy–nanosilica composites containing 40% of TEOS. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 757–768, 2006     

Facile,one‐pot synthesis of aromatic diamine‐based benzoxazines and their advantages over diamines as epoxy hardeners

Three aromatic diamine‐based benzoxazines were successfully prepared by a facile, clean, one‐pot procedure from 1,4‐phenylenediamine ( 1 ), 4,4′‐diaminodiphenyl ether ( 2 ), and 4,4′‐diaminodiphenyl methane ( 3 ), respectively. Their structures were confirmed by NMR spectra and single crystal diffractogram. The effect of the reactivity of diamines on the purity of the resultant benzoxazines was discussed. The resultant benzoxazines were applied as hardeners for cresol novolac epoxy (CNE). The processing window, the latent curing characteristic, and the miscibility of benzoxazine/CNE systems were discussed. Compared with diamines ( 1 and 3 ), ( 1 and 3 )‐based benzoxazines show latent curing characteristic as epoxy hardeners, and wide processing windows can be obtained. Compared with diamine ( 2 ) which is immiscible with CNE in the molten state, ( 2 )‐based benzoxazine shows good miscibility with CNE. Dynamic mechanical analysis shows the T_gs of the benzoxazine/CNE thermosets are as high as 242–243 °C. Thermogravimetric analysis shows the outstanding thermal stability of the resultant thermosets. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2430–2437, 2010     

Curing reaction of o-cresol novolac epoxy resin according to hardener change

The investigations of cure kinetics and glass transition temperature (T_g) versus reaction conversion (α) of o-cresol novolac epoxy resin with the change of hardener were performed. All kinetic parameters of the curing reaction such as the reaction rate order, activation energy, and frequency factor were calculated. The curing mechanisms were classified into two types. One was an autocatalytic mechanism and the other was a nth order kinetic mechanism. The constants related to the chain mobility of polymer segments were obtained by using the DiBenedetto equation. We have tried to correlate the relationships between curing mechanism and molecular structures of hardeners from these results. © 1993 John Wiley & Sons, Inc.     

Thermal properties and fracture toughness of epoxy resins cured by phosphonium and pyrazinium salts as latent cationic initiators

In this work, the latent thermal cationic initiators triphenyl benzyl phosphonium hexafluoroantimonate (TBPH) and benzyl‐2‐methylpyrazinium hexafluoroantimonate (BMPH) were newly synthesized and characterized with IR, ¹H NMR, and P NMR spectroscopy. The thermal and mechanical properties of difunctional epoxy [diglycidyl ether of bisphenol A (DGEBA)] resins cured by 1 phr of either TBPH or BMPH were investigated. The DGEBA/TBPH system showed a higher curing temperature and a higher critical stress intensity factor than the epoxy/BMPH system. This could be interpreted in terms of the slow thermal diffusion rate and bulk structure of the four phenyl groups in TBPH. However, the decomposition activation energy derived from the Coats–Redfern method was lower for epoxy/TBPH. This result was probably due to the fact that a broken short‐chain structure was developed by the steric hindrance of TBPH in the difunctional epoxy resin. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2393–2403, 2003