Positron annihilation properties of copolyimides and copolyamides with microphase‐separated structures

The positron annihilation lifetime (PAL) of a series of copolyimides and copolyamides with microphase‐separated structures was measured to investigate the effects of different hard‐segment polymers on the PAL properties of soft‐segment domains of poly(dimethyl‐siloxane) (PDMS) and poly(ethylene oxide) (PEO). The lifetime (τ₃) and intensity (I₃) of the long‐lived component are given as a function of the PDMS or PEO content for a series of copolymers, of which the density roughly obeys the additive rule except for the PDMS‐segmented copolyamides. The PDMS‐segmented copolyimides and copolyamides show much smaller I₃ values than those estimated from the additive rule. The lifetime distribution of the long‐lived component for the PDMS‐segmented copolyamides is composed of two components. The longer‐lifetime component is attributed to pure PDMS domains, and the shorter‐lifetime component is attributed to the polyamide domains, intermediate phases, and PDMS domains containing small amounts of short amide blocks. Despite the high PDMS content, the latter component is rather large. Thus, the positronium formation in the PDMS domains of the copolyimides and copolyamides is effectively reduced. This can be explained by the combination of the difference in the electron affinity of the PDMS and polyimide or polyamide segments and the incomplete phase separation. The PEO‐segmented copolyimides show much smaller I₃ values than those predicted from the additive rule. This is likely attributable to the effects of the intermediate phases. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1123–1132, 2000     

Gas transport properties of poly(ether‐b‐amide) segmented block copolymers

The permeation properties of H₂, N₂, and CO₂ were determined at 35 °C and pressures up to 15 atm in phase‐separated polyether‐b‐polyamide segmented block copolymers. These polymers contain poly(ethylene oxide) [PEO] or poly(tetramethylene oxide) [PTMEO] as the rubbery polyether phase and nylon‐6 [PA6] or nylon‐12 [PA12] as the hard polyamide phase. Extremely high values of polar (or quadrupolar)/nonpolar gas selectivities, coupled with high CO₂ permeability coefficients, were observed. CO₂/H₂ selectivities as high as 9.8 and CO₂/N₂ selectivities as high as 56 were obtained in polymers with CO₂ permeability coefficients of approximately 220 × 10⁻¹⁰ cm³(STP) cm/(cm² s cmHg). As the amount of polyether increases, permeability increases. Gas permeability is higher in polymers with less polar constituents, PTMEO and PA12, than in those containing the more polar PEO and PA6 units. CO₂/N₂ and CO₂/H₂ selectivities are higher in polymers with higher concentrations of polar groups. These high selectivity values derive from large solubility selectivities in favor of CO₂. Because CO₂ is larger than H₂ and has, therefore, a lower diffusion coefficient than H₂, the weak size‐sieving ability of the rubbery polyether phase, which is the locus of most of the gas permeation, also contributes to high CO₂/H₂ selectivity. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2051–2062, 2000     

Calorimetric and Dielectric Study of the Segmented Biodegradable Poly(ester‐urethane)s Based on Bacterial Poly[(R)‐3‐hydroxybutyrate]

Two series of segmented poly(ester‐urethane)s were synthesized from bacterial poly[(R)‐3‐hydroxybutyrate]‐diol (PHB‐diol), as hard segments, and either poly(ε‐caprolactone)‐diol (PCL‐diol) or poly(butylene adipate)‐diol (PBA‐diol), as soft segments, using 1,6‐hexamethylene diisocyanate as a chain extender. The hard‐segment content varied from 0 to 50 wt.‐%. These materials were characterized using ¹H NMR spectroscopy and GPC. The polymers obtained were investigated calorimetrically and dielectrically. DSC showed that the T_g of either the PCL or PBA soft segments are shifted to higher temperatures with increasing PHB hard‐segment content, revealing that either the PCL or PBA are mixed with small amounts of PHB in the amorphous domains. The results also showed that the crystallization of soft or hard segments was physically constrained by the microstructure of the other crystalline phase, which results in a decrease in the degree of crystallinity of either the soft or hard segments upon increase of the other component. The dielectric spectra of poly(ester‐urethane)s, based on PCL and PHB, showed two primary relaxation processes, designated as α_S and α_H, which correspond to glass–rubber transitions of PCL soft and PHB hard segments, respectively. Whereas in the case of other poly(ester‐urethane)s, derived from PBA and PHB, only one relaxation process was observed, which broadens and shifts to higher temperature with increasing PHB hard‐segment content. It was concluded from these results that our investigated materials exhibit micro‐phase separation of the hard and soft segments in the amorphous domains.     

Highly selective multilayer polymer thin films for CO2/N2 separation

Multilayer thin films of poly(ethylene oxide) (PEO) and poly(methacrylic acid) (PMAA), deposited via layer‐by‐layer (LbL) assembly from aqueous solutions, are investigated for CO₂/N₂ separation. Eight and ten bilayer (217 and 389 nm thick, respectively) PEO/PMAA thin films deposited on a 25 μm polystyrene substrate exhibit CO₂/N₂ selectivities of 142 and 136, respectively. These are the highest reported to‐date for this gas pair separation using a homogeneous polymer film. While further work remains to improve CO₂ permeability, these results indicate the potential of LbL assemblies as standalone CO₂ separation membranes for low‐flux/high‐purity applications, or as part of a composite and/or mixed‐matrix membrane for high‐flux applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1730–1737     

Synthesis and characterization of poly(dimethylsiloxane‐urethane) elastomers: Effect of hard segments of polyurethane on morphological and mechanical properties

A series of poly(dimethylsiloxane‐urethane) elastomers based on hexamethylenediisocyanate, toluenediisocyanate, or 4,4′‐methylenediphenyldiisocyanate hard segment and polydimethylsiloxane (PDMS) soft segment were synthesized. In this study, a new type of soft‐segmented PDMS crosslinker was synthesized by hydrosilylation reaction of 2‐allyloxyethanol with polyhydromethylsiloxane, using Karstedt's catalyst. The synthesized soft‐segmented crosslinker was characterized by FT‐IR, ¹H, and ¹³C NMR spectroscopic techniques. The mechanical and thermal properties of elastomers were characterized using tensile testing, thermogravimetric analysis, differential scanning calorimetry (DSC), and dynamical mechanical analysis measurements. The molecular structure of poly(dimethylsiloxane‐urethane) membranes was characterized by ATR‐FTIR spectroscopic techniques. Infrared spectra indicated the formation of urethane/urea aggregates and hydrogen bonding between the hard and soft domains. Better mechanical and thermal properties of the elastomers were observed. The restriction of chain mobility has been shown by the formation of hydrogen bonding in the soft and hard segment domains, resulting in the increase in the glass‐transition temperature of soft segments. DSC analysis indicates the phase separation of the hard and soft domains. The storage modulus (E′) of the elastomers was increasing with increase in the number of urethane connections between the hard and soft segments. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2980–2989, 2006     

Synthesis of Porous,Nitrogen‐Doped Adsorption/Diffusion Carbonaceous Membranes for Efficient CO2 Separation

A porous, nitrogen‐doped carbonaceous free‐standing membrane (TFMT‐550) is prepared by a facile template‐free method using letrozole as an intermediate to a triazole‐functionalized‐triazine framework, followed by carbonization. Such adsorption/diffusion membranes exhibit good separation performance of CO₂ over N₂ and surpassing the most recent Robeson upper bound. An exceptional ideal CO₂/N₂ permselectivity of 47.5 was achieved with a good CO₂ permeability of 2.40 × 10⁻¹³ mol m m⁻² s⁻¹ Pa⁻¹. The latter results arise from the presence of micropores, narrow distribution of small mesopores and from the strong dipole–quadrupole interactions between the large quadrupole moment of CO₂ molecules and the polar sites associated with N groups (e.g., triazine units) within the framework.     

Synthesis of poly(N,N‐dimethylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N,N‐dimethylacrylamide) and its application for separation of proteins by capillary zone electrophoresis

A series of well‐defined triblock copolymers, poly(N, N‐dimethylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N, N‐dimethylacrylamide) (PDMA‐b‐PEO‐b‐PDMA) synthesized by atom transfer radical polymerization, were used as physical coatings for protein separation. A comparative study of EOF showed that the triblock copolymer presented good capillary coating ability and EOF efficient suppression. The effects of the M_r of PDMA block in PDMA‐b‐PEO‐b‐PDMA triblock copolymer and buffer pH on the separation of basic protein for CE were investigated. Moreover, the influence of the copolymer structure on separation of basic protein was studied by comparing the performance of PDMA‐b‐PEO‐b‐PDMA triblock copolymer with PEO‐b‐PDMA diblock copolymer. Furthermore, the triblock copolymer coating showed higher separation efficiency and better migration time repeatability than fused‐silica capillary when used in protein mixture separation and milk powder samples separation, respectively. The results demonstrated that the triblock copolymer coatings would have a wide application in the field of protein separation.     

Tuning Pore Size in Square‐Lattice Coordination Networks for Size‐Selective Sieving of CO2

Porous materials capable of selectively capturing CO₂ from flue‐gases or natural gas are of interest in terms of rising atmospheric CO₂ levels and methane purification. Size‐exclusive sieving of CO₂ over CH₄ and N₂ has rarely been achieved. Herein we show that a crystal engineering approach to tuning of pore‐size in a coordination network, [Cu(quinoline‐5‐carboxyate)₂]_n ( Qc‐5‐Cu ) ena+bles ultra‐high selectivity for CO₂ over N₂ (S_CN≈40 000) and CH₄ (S_CM≈3300). Qc‐5‐Cu‐sql‐β , a narrow pore polymorph of the square lattice ( sql ) coordination network Qc‐5‐Cu‐sql‐α, adsorbs CO₂ while excluding both CH₄ and N₂. Experimental measurements and molecular modeling validate and explain the performance. Qc‐5‐Cu‐sql‐β is stable to moisture and its separation performance is unaffected by humidity.     

Improved self‐assembly of poly(dimethylsiloxane‐b‐ethylene oxide) using a hydrogen‐bonding additive

Block copolymers with increased Flory–Huggins interaction parameters (χ) play an essential role in the production of sub‐10 nm nanopatterns in the growing field of directed self‐assembly for next generation lithographic applications. A library of PDMS‐b‐PEO block copolymers were synthesized by click chemistry and their interaction parameters (χ) determined. The highest χ measured in our samples was 0.21 at 150 °C, which resulted in phase‐separated domains with periods as small as 7.9 nm, suggesting that PDMS‐b‐PEO is a prime candidate for sub‐10 nm nanopatterning. To suppress PEO crystallization, PDMS‐b‐PEO was blended with (l )‐tartaric acid (LTA) which allows for tuning of the self‐assembled morphologies. Additionally, it was observed that the order‐disorder transition temperature (T_ODT) of PDMS‐b‐PEO increased dramatically as the amount of LTA in the blend increased, allowing for further control over self‐assembly. To understand the mechanism of this phenomenon, we present a novel field‐based supramolecular model, which describes the formation of copolymer‐additive complexes by reversible hydrogen bonding. The mean‐field phase separation behavior of the model was calculated using the random phase approximation (RPA). The RPA analysis reproduces behavior consistent with an increase of the effective χ in the PDMS‐b‐(PEO/LTA suprablock). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2200–2208     

Syntheses and properties of organosoluble polyamides and polyimides based on the diamine 3,3‐bis[4‐(4‐aminophenoxy)‐3‐methylphenyl]phthalide derived from o‐cresolphthalein

Diamine 3,3‐bis[4‐(4‐aminophenoxy)‐3‐methylphenyl]phthalide (BAMP) was derived from the o‐cresolphthalein, and then it was polycondensated with various aromatic dicarboxylic acids and dianhydrides to synthesize polyamides (PAs) and polyimides (PIs), respectively. PAs have inherent viscosities of 0.78–2.24 dL/g. Most of the PAs are readily soluble in a variety of solvents such as DMF, DMAc, and NMP and afforded transparent and tough films from DMAc solutions. The cast films have tensile strengths of 75–113 MPa as well as initial moduli of 1.71–2.97 GPa. These PAs have glass transition temperatures (T_gs) in the range of 242–325°C, 10% weight loss temperatures occur up to 473°C, and char yields are between 57 and 64% at 800°C in nitrogen. PIs were first synthesized to form polyamic acids (PAAs) by a two‐stage procedure that included a ring‐opening reaction, followed by thermal or chemical conversion to polyimides. Inherent viscosities of PAAs are between 0.71 and 1.63 dL/g. Most of the PIs obtained through the chemical cyclodehydration procedure are soluble in NMP, o‐chlorophenol, m‐cresol, etc., and they have inherent viscosities of 0.58–1.32 dL/g. T_gs of these PIs are in the range of 270–305°C and show 10% weight loss temperatures up to 477°C. PIs obtained through the thermal cyclodehydration procedure have tensile strengths of 72–142 MPa, elongations at break of 8–19%, and initial moduli of 1.80–2.72 GPa. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 455–464, 1999     

MIL‐53(Al) as a Versatile Platform for Ionic‐Liquid/MOF Composites to Enhance CO2 Selectivity over CH4 and N2

Five different imidazolium‐based ionic liquids (ILs) were incorporated into a metal–organic framework (MOF), MIL‐53(Al), to investigate the effect of IL incorporation on the CO₂ separation performance of MIL‐53(Al). CO₂, CH₄, and N₂ adsorption isotherms of the IL/MIL‐53(Al) composites and pristine MIL‐53(Al) were measured to evaluate the effect of the ILs on the CO₂/CH₄ and CO₂/N₂ selectivities of the MOF. Of the composite materials that were tested, [BMIM][PF₆]/MIL‐53(Al) exhibited the largest increase in CO₂/CH₄ selectivity, 2.8‐times higher than that of pristine MIL‐53(Al), whilst [BMIM][MeSO₄]/MIL‐53(Al) exhibited the largest increase in CO₂/N₂ selectivity, 3.3‐times higher than that of pristine MIL‐53(Al). A comparison of the CO₂ separation potentials of the IL/MOF composites showed that the [BMIM][BF₄]‐ and [BMIM][PF₆]‐incorporated MIL‐53(Al) composites both showed enhanced CO₂/N₂ and CO₂/CH₄ selectivities at pressures of 1–5 bar compared to composites of CuBTC and ZIF‐8 with the same ILs. These results demonstrate that MIL‐53(Al) is a versatile platform for IL/MOF composites and could help to guide the rational design of new composites for target gas‐separation applications.     

Ultra‐Tuning of the Aperture Size in Stiffened ZIF‐8_Cm Frameworks with Mixed‐Linker Strategy for Enhanced CO2/CH4 Separation

ZIF‐8 membrane has the potential for CO₂/CH₄ separation based on size exclusion. But if traditionally prepared by solvothermal methods, it shows only negligible selectivity due to the linker mobility. Here, ≈500 nm‐thin hybrid ZIF‐7_x‐8 membranes with suppressed linker mobility and narrowed window aperture are prepared by a fast current‐driven synthesis (FCDS) within 20 min. The in situ electric field during FCDS allows the formation of stiffened ZIF‐8_Cm as parent skeleton and the mixed‐linker strategy is applied to narrow the aperture size simultaneously. The ZIF‐7₂₂‐8 membrane shows significantly sharpened molecular sieving for CO₂/CH₄ with a separation factor above 25, which soared tenfold compared with other unmodified ZIF‐8 membranes. Additionally, the membrane shows exceptional separation performance for H₂/CH₄ and CO₂/N₂, with separation factors of 71 and 20, respectively. After 180 h temperature swing operation, it still maintains the excellent separation performance.     

Gas sorption and characterization of poly(ether‐b‐amide) segmented block copolymers

The solubilities of He, H₂, N₂, O₂, CO₂, CH₄, C₂H₆, C₃H₈, and n‐C₄H₁₀ were determined at 35°C and pressures up to 27 atmospheres in a systematic series of phase separated polyether–polyamide segmented block copolymers containing either poly(ethylene oxide) [PEO] or poly(tetramethylene oxide) [PTMEO] as the rubbery polyether phase and nylon 6 [PA6] or nylon 12 [PA12] as the hard polyamide phase. Sorption isotherms are linear for the least soluble gases (He, H₂, N₂, O₂, and CH₄), convex to the pressure axis for more soluble penetrants (CO₂, C₃H₈, and n‐C₄H₁₀) and slightly concave to the pressure axis for ethane. These polymers exhibit high CO₂/N₂ and CO₂/H₂ solubility selectivity. This property appears to derive mainly from high carbon dioxide solubility, which is ascribed to the strong affinity of the polar ether linkages for CO₂. As the amount of the polyether phase in the copolymers increases, gas solubility increases. The solubility of all gases is higher in polymers with less polar constituents, PTMEO and PA12, than in polymers with more polar PEO and PA6 units. CO₂/N₂ and CO₂/H₂ solubility selectivity, however, are higher in polymers with higher concentrations of polar repeat units. The sorption data are complemented with physical characterization (differential scanning calorimetry, elemental analysis, and wide angle X‐ray diffraction) of the various block copolymers. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2463–2475, 1999     

Crystallization and morphology of poly(ethylene oxide‐b‐lactide) crystalline–crystalline diblock copolymers

The crystallization behaviors and morphology of asymmetric crystalline–crystalline diblock copolymers poly(ethylene oxide‐lactide) (PEO‐b‐PLLA) were investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and microscopic techniques (polarized optical microscopy (POM) and atomic force microscopy (AFM)). Both blocks of PEO₅‐b‐PLLA₁₆ can be crystallized, which was confirmed by WAXD, while PEO block in PEO₅‐b‐PLLA₃₀ is difficult to crystallize because of the confinement induced by the high glass transition temperature and crystallization of PLLA block with the microphase separation of the block copolymer. Comparing with the crystallization and morphology of PLLA homopolymer and differences between the two copolymers, we studied the influence of PEO block and microphase separation on the crystallization and morphology of PLLA block. The boundary temperature (T_b) was observed, which distinguishes the crystallization into high‐ and low‐temperature ranges, the growth rate and morphology were quite different between the ranges. Crystalline morphologies including banded spherulite, dendritic crystal, and dense branching in PEO₅‐b‐PLLA₁₆ copolymer were formed. The typical morphology of dendritic crystals including two different sectors were observed in PEO₅‐b‐PLLA₃₀ copolymer, which can be explained by secondary nucleation, chain growth direction, and phase separation between the two blocks during the crystallization process. Lozenge‐shaped crystals of PLLA with screw dislocation were also observed employing AFM, but the crystalline morphology of PEO block was not observed using microscopy techniques because of its small size. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1400–1411, 2008     

Efficient CO2 Removal for Ultra‐Pure CO Production by Two Hybrid Ultramicroporous Materials

Removal of CO₂ from CO gas mixtures is a necessary but challenging step during production of ultra‐pure CO as processed from either steam reforming of hydrocarbons or CO₂ reduction. Herein, two hybrid ultramicroporous materials (HUMs), SIFSIX‐3‐Ni and TIFSIX‐2‐Cu‐i , which are known to exhibit strong affinity for CO₂, were examined with respect to their performance for this separation. The single‐gas CO sorption isotherms of these HUMs were measured for the first time and are indicative of weak affinity for CO and benchmark CO₂/CO selectivity (>4000 for SIFSIX‐3‐Ni ). This prompted us to conduct dynamic breakthrough experiments and compare performance with other porous materials. Ultra‐pure CO (99.99 %) was thereby obtained from CO gas mixtures containing both trace (1 %) and bulk (50 %) levels of CO₂ in a one‐step physisorption‐based separation process.     

Fabrication‐controlled morphology of poly(butylene succinate) nano‐microcellular foams by supercritical CO2

Poly(butylene succinate) urethane ionomer (PBSUIs) foams with nano‐microcellular morphology were fabricated using supercritical CO₂ (sc‐CO₂) at different parameters. Effect of urethane ionic group (UIG) content (ranged from 1% to 5%) on the rheology and crystallization of PBSUIs were evaluated by intrinsic, dynamic rheological, X‐ray diffraction, and differential scanning calorimetry measurements. The results show that the complex viscosity of PBSUIs vastly improved, while their intrinsic viscosity and crystallinity decreased. They also evidenced that CO₂ promoted the formation of crystallites in the amorphous and increased the X_c of PBSU and PBSUIs foams. Scanning electron microscope was employed to explore the influences of UIG content and foaming parameters on the morphologies of PBSUIs microcellular foams, and it revealed that UIG content was the dominated factor. The cell size and cell densities of PBSUIs microcellular foams were smaller than 5.0 micrometers and higher than 1.5 × 10¹⁰ cells/cm³, respectively, even foamed at diverse variations of foam temperature and pressure. Interestingly, PBSUIs with 3% and 5% UIG content achieved microcellular foams in nano‐cells, high‐stretched elliptical shape. The mechanism was ascribed that these PBSUIs with high melt viscosities could retard the CO₂ bubbles to merge during the foam process and induce the cells to stretch and orient in depressururization direction. This study proposed a novel method for fabricating PBS nano‐microcellular foams.     

Polyurethane‐mesoporous silica gas separation membranes

The concept of mixed matrix membrane comprising dispersed inorganic fillers into a polymer media has revealed appealing to tune the gas separation performance. In this work, the membranes were prepared by incorporation of mesoporous silica into polyurethane (PU). Mesoporous silica particles with different pore size and structures, MCM‐41, cubic MCM‐48 and SBA‐16, were synthesized by templating method and functionalized with 3‐aminopropyltriethoxysilane (APTES). High porosity and aminated surface of the mesoporous silica enhance the adhesion of the particles to the PU matrix. The SEM and FTIR results showed strong interactions between the particles and the PU chains. Moreover, the thermal stability of the hybrid PUs improved compared to the pure polymer. Gas transport properties of the membranes were measured for pure CO₂, CH₄, O₂, and N₂ gases at 10 bar and 25°C. The results showed that the gas permeabilities enhanced with increasing in the loading of modified mesoporous silica particles. High porosity and amine‐functionalized particles render opportunities to enhance the gas diffusivity and solubility through the membranes. The enhanced gas transport properties of the mixed matrix membranes reveal the advantages of mesoporous silica to improve the gas permeability (CO₂ permeability up to ~70) without scarifying the gas selectivity (α(CO₂/N₂)~ 30 for 5 wt% SBA‐16 content).     

Azine‐Linked Covalent Organic Framework (COF)‐Based Mixed‐Matrix Membranes for CO2/CH4 Separation

Mixed‐matrix membranes (MMMs) comprising Matrimid and a microporous azine‐linked covalent organic frameworks (ACOF‐1) were prepared and tested in the separation of CO₂ from an equimolar CO₂/CH₄ mixture. The COF‐based MMMs show a more than doubling of the CO₂ permeability upon 16 wt % ACOF‐1 loading together with a slight increase in selectivity compared to the bare polymer. These results show the potential of COFs in the preparation of MMMs.     

Synthesis,characterization, and molecular modeling studies of novel polyurethanes based on 2,2′‐[ethane‐1,2‐diylbis(nitrilomethylylidene)]diphenol and 2,2′‐[hexane‐1,6‐diylbis(nitrilomethylylidene)] diphenol hard segments

Novel polyurethanes (PUs) based on 2,2′‐[ethane‐1,2‐diylbis(nitrilomethylylidene)]diphenol and 2,2′‐[hexane‐1,6‐diylbis(nitrilomethylylidene)]diphenol as hard segments containing four aromatic diisocyanates (4,4′‐diphenylmethane diisocyanate, toluene 2,4‐diisocyanate, isophorone diisocyanate, and hexamethylene diisocyanate) have been prepared. Fourier transform infrared, UV spectrophotometry, fluorescence spectroscopy, ¹H NMR and ¹³C NMR spectroscopy, thermogravimetric analysis, and differential thermal analysis have been used to determine the structural characterization and thermal properties of the segmented PUs. All the PUs contain domains of both semicrystalline and amorphous structures, as indicated by X‐ray diffraction. The acoustic properties have been calculated with the group contribution method. Molecular dynamics simulations have been performed on all the PUs to estimate the cohesive energy density and solubility parameter values, which compare well with the values calculated with the group contribution method. Furthermore, the simulation protocols have been applied to the PUs to produce X‐ray diffraction plots to determine the phase morphology of the PUs. The surface properties of the PUs have been estimated from the simulation protocols. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6032–6046, 2006     

Hyperthin Membranes for Gas Separations via Layer‐by‐Layer Assembly

Thin film formation via the Layer‐by‐Layer method is now a well‐established and broadly used method in materials science. We have been keenly interested in exploiting this technique in the area of gas separations. Specifically, we have sought to create hyperthin (<100 nm) polyelectrolyte‐based membranes that have practical potential for the separation of CO₂ from N₂ (flue gas) and H₂ from CO₂ (syngas). In this personal account, we summarize recent studies that have been aimed at measuring the influence of a variety of factors that can affect the permeability and permeation selectivity of hyperthin polyelectrolyte multilayers (PEMs).