Compact layer influence on hysteresis effect in organic–inorganic hybrid perovskite solar cells

Organic–inorganic hybrid perovskite solar cells have attracted great attention due to their high power conversion efficiency and low cost. However, an anomalous hysteresis effect exists in the perovskite solar cells, especially with TiO₂ as the n-type electron extraction layer. In this communication, we prepare two kinds of TiO₂ compact layers using Atomic Layer Deposition (ALD) and Spin-Coating (SC) methods and compare their influences on the hysteresis effect. By efficiency comparison and AC impedance spectroscopy study, we find that the thickness and morphology of compact layer have a significant influence on the hysteresis effect. Compared to the SC approach, the ALD prepared compact layer is ultra-thin with uniform morphology and shows small interfacial capacitance and large recombination resistance, meaning reduced interfacial charge accumulation and accelerated electron transport, which would relieve the hysteresis effect.     

Electrochemical Impedance Spectra of Poly(3-octylthiophene) Films

Charge transfer in poly(3-octylthiophene) films in 0.05–0.5 M LiClO₄ solutions in acetonitrile is studied by an electrochemical impedance method. The resistance to charge transfer R _ct and the capacitance of the electrical double layer C _dl are calculated from the high-frequency semicircle and referred to the film/electrolyte interface. The low-frequency capacitance C _lf and effective diffusion coefficient D _ef are determined by analyzing the region of medium and low frequencies. The discrepancies between potential dependences of C _lf and D _ef derived experimentally and calculated within a simple model for a redox film are analyzed. The assumption is made that additional factors, such as a macroporous character of the films and the change in their properties during oxidation, which results from the film swelling, the change in the film volume and the solvation character, should be taken into account.     

Anomalous lithium ion diffusion into CeO2·TiO2 thin film by film thickness variations

CeO₂·TiO₂ thin film is considered as an excellent candidate for a passive ion storage layer due to its good electrochemical stability and comparatively great charge capacitance. When cerium-titanium oxide thin film is adopted as an ion storage layer against cathodic tungsten oxide layer, the electrochromic device shows long term durability and cyclability. Therefore, many researchers investigated the composition and crystallinity effects to the charge density. In our study, we prepared CeO₂·TiO₂ thin by sol–gel dip-coating method, varying thickness by controlling withdrawal speeds. As investigating results of cyclic voltammetry and chronocoulometry, we found that there are three regions in the film thicknesses: (1) fast lithium ion diffusion region under 100 nm, (2) slow diffusion region in the range of 100 to 150 nm, and (3) fast and great charge capacitance region over 150 nm. In region 1, lithium ions diffuse very fast and reach into indium-tin oxide (ITO) layers, and slow diffusion region follows in region 2, probably due to the remains or impurities within the film, and in region 3, lithium ion diffusion gets fast again, accompanied with charge capacitance increase with thickness.     

Synthesis and characterization of novel InVO<Subscript>4</Subscript>–TiO<Subscript>2</Subscript> thin films using the low temperature sol

The InVO₄ sol was obtained by a mild hydrothermal treatment (the precursor precipitation solution at 423 K, for 4 h). Novel visible-light activated photocatalytic InVO₄–TiO₂ thin films were synthesized through a sol–gel dipping method from the composite sol, which was obtained by mixing the low temperature InVO₄ sol and TiO₂ sol. The photocatalytic activities of the new InVO₄–TiO₂ thin films under visible light irradiation were investigated by the photocatalytic discoloration of methyl orange aqueous solution. The thin films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and UV–Vis absorption spectroscopy (UV–Vis). The results revealed that the InVO₄ doped thin films enhanced the methyl orange degradation rate under visible light irradiation, 3.0 wt% InVO₄–TiO₂ thin films reaching 80.1% after irradiated for 15 h.     

Electrochemical impedance spectroscopy of mesoporous Al-stabilized TiO<Subscript>2</Subscript> (anatase) in aprotic medium

High-frequency electrochemical impedance spectroscopy was used to investigate the mesoporous film of Al-stabilized TiO₂ on F-doped SnO₂ support in 1 M Li(CF₃SO₂)₂N in ethylene carbonate/dimethoxyethane (1:1 v/v). Kinetic parameters, viz. charge transfer resistance and chemical diffusion coefficient, were determined. Charge transfer resistance increased with time of contact of electrode in the above aprotic electrolyte solution. The increase followed exponential dependence, whereas the double layer capacitance, simultaneously, decreased exponentially with time. These effects were discussed in terms of the solid–electrolyte interface, which undergoes chemical changes upon contact with the electrolyte solution. Adel Attia is currently on leave from the Department of Physical Chemistry, National Research Center, El-Tahrir St., Dokki 12622, Cairo, Egypt.     

Preparation and characterization of TiO<Subscript>2</Subscript> hybrid sol for UV-curable high-refractive-index organic–inorganic hybrid thin films

In this study, UV-curable hybrid thin films were successfully prepared from TiO₂ and TiO₂ hybrid sols containing the acrylic monomer DPHA on PMMA substrates. The prepared TiO₂ and TiO₂ hybrid sols showed long-term storage stability and can provide operating control for the preparation of high-refractive-index hybrid thin films. The existence of interaction between the TiO₂ particle and the coupling agent was evidenced by FT-IR and UV–visible spectra. All hybrid thin films showed good adhesion to the PMMA substrate with refractive index falling over the range 1.64–1.77. These results suggested the potential application of present TiO₂ hybrid films in optical devices, such as anti-reflective coatings.     

Tribological performance of fluoroalkylsilane modification of sol–gel TiO<Subscript>2</Subscript> coating

This paper explores the possibility of making coatings with super friction-reducing and wear protection properties by using both sol–gel and self-assembling techniques. The thin film of TiO₂ was firstly prepared on glass substrates via a sol–gel method, followed by sintering at 480°C. The self-assembled monolayer of Fluoroalkylsilane (FAS) were then prepared on TiO₂ thin film to obtain TiO₂–FAS dual-layer film. The contact angle measurement and X-ray photoelectron spectroscopy were used to determine the wetting behavior and chemical structure of films, respectively. The friction behavior of films sliding against a steel ball was examined on a macro friction and wear tester. It is shown that FAS is strongly adsorbed on sol–gel derived TiO₂ thin film, making it strongly hydrophobic. Good friction-reducing and wear protection behavior is observed for the glass substrate after duplex surface-modification with sol–gel TiO₂ and top layer of FAS.     

Tribological performance of fatty acid modification of sol–gel TiO<Subscript>2</Subscript> coating

In this paper, the coatings with friction-reducing properties were investigated using both sol–gel and self-assembling techniques. The thin film of TiO₂ was firstly prepared on glass substrates via a sol–gel method, followed by calcinating at 480 °C. The films of fatty acid were then deposited on the TiO₂ surface to obtain a dual-layer film. The contact angle measurement and FT IR spectroscopy were used to determine the wetting behavior and chemical structure of films, respectively. The friction-reducing behavior of films sliding against a steel ball was examined on a macro friction and wear tester. It is found that fatty acid is strongly adsorbed on sol–gel derived TiO₂ surface. Good friction-reducing behavior is observed for the glass substrate after duplex surface-modification with TiO₂ surface obtained by sol–gel method and top layer of fatty acid.     

Capacitance and photocurrent study of electronic properties of anodic oxide films on Nb and Ta. Evaluation of the ionized donor concentration profile in Nb2O5 film

Electronic properties of electrochemically formed oxide films on Nb were studied by photocurrent and differential capacitance measurements in 0.025 M KH₂PO₄+0.025 M Na₂HPO₄ electrolyte, pH 6.9. Oxide films of n-type conductivity were formed galvanostatically for final potentials ranging from 4 to 230 V. Measurements were performed in two potential regions, which correspond to formation of a depleted layer of variable thickness at relatively low potentials, and to complete depletion of oxide films of electronic charge carriers at higher potentials. In the first potential region the behavior of both capacitance and photocurrent, was governed by a build up of a depleted layer of potential dependent thickness. In the second, high potential, region, which extends up to the oxide film formation potential, the photocurrent and capacitance of oxide films in most features followed the trends typical of dielectric films containing defects and traps. The photocurrent and capacitance measurements on presumably dielectric oxide films formed on Ta were staged for comparison. The capacitance–potential measurements performed in the first potential region enabled us to construct the ionized donor concentration profile across the Nb₂O₅ film width. The limitations on the use of the C–E profiling method for electrochemically formed oxide layers are considered.     

Effect of silver incorporation on crystallization and microstructural properties of sol–gel derived titania thin films on glass

Titanium dioxide (TiO₂) thin films, with and without silver (Ag), were prepared on float glass via sol–gel processing. The float glass substrates were pre-coated with a silica-barrier layer prior to the deposition of TiO₂-based thin films. Silver nanoparticle incorporation into the TiO₂ matrix was achieved by thermal reduction of Ag ions dissolved in a titanium-n-butoxide (Ti[O(CH₂)₃CH₃]₄) based sol during calcination in air at 250, 450 and 650 °C. Thin films were characterized using glancing incidence X-ray diffraction, UV–visible spectroscopy, X-ray photoelectron spectroscopy, and Raman spectroscopy. The effects of Ag concentration and calcination temperature on microstructure and on chemical and physical properties of the thin films have been reported. The size and chemical state of Ag particles, as well as the phase characteristics of the titania matrix were strongly influenced by Ag concentration and calcination temperature. Results from this study can be utilized in both processing and structure-functional property optimization of sol–gel based Ag-TiO₂ thin films by aqueous routes.     

Antireflective sol–gel TiO2 thin films for single crystal silicon and textured polycrystal silicon

In this paper, antireflective TiO₂ thin films have been prepared on single crystal silicon, and textured polycrystal silicon by sol–gel route using the dip-coating technique. The thickness and the refractive index of the films have been optimised to obtain low reflexion in the visible region, by controlling both the concentration of the titanium isopropoxide (Ti(ⁱOPr)₄), and the annealing temperature. We showed that the use of a TiO₂ single layer with a thickness of 64.5 nm, heat-treated at 450 or 300 °C, reduces the reflection on single crystal silicon at a level lower than 3% over the broadband spectral ranges 670–830 nm and 790–1010 nm, respectively. In order to broaden the spectral minimum reflectance as much as possible, we have proposed to texture polycrystal silicon wafers, and to coat these wafers by a TiO₂ single layer with a thickness of 73.4 nm. In this case, the reflectance has been reduced from 27 to 13% in the spectral range 460–1000 nm.     

掺杂纳米金粒子的火焰氧化TiO2膜的光电化学性质的研究

A nano-Au modified TiO2 electrode was prepared via the oxidation of Ti sheet in flame and subsequent modification with gold nanoparticles. The results of SEM and TEM measurements show that the Au nanoparticles are well dispersed on TiO2 surface. A near 2-fold enhancement in photocurrent was achieved upon the modification with Au nanoparticles. From the results of photocurrent and electrochemical impedance experiments it was found that the flatband potential of nano-Au/TiO2 electrode negatively shifted about 100 mV in 0.5 mol/L Na2SO4 solutions compared with that of bare TiO2 electrode. The improvement of photoelectrochemical performance was explained by the inhibition for charge recombination of photo-induced electrons and holes, and the promotion for interracial charge-transfer kinetics at nano-Au/TiO2 composite film. Such nanometal-semiconductor composite films have the potential application in improving the performance of photoelectrochemical solar cells.     

Relation between morphology and conductivity in TiO2 nanotube arrays: an electrochemical impedance spectrometric investigation

Two types of TiO₂ nanotubular arrays were obtained by anodisation of a titanium foil, in two different solutions containing fluoride ions. For the first type which has rough tube walls, impedance measurements in the dark showed the presence of a localised surface state which was related to adsorbed molecular water. Under UV illumination, this adsorbed molecular water was photo-dissociated. Moreover, an increase of 2 orders of magnitude for the limiting capacitance of the space charge layer was observed, simultaneously with the disappearance of the localised state and with a 100-time increase of the carrier density associated with hydrogen insertion. The second type of layer was characterised by smoother tube walls, a high doping level (10²⁰?cm^?3) in the dark, a lack of localised states and no long-lasting photo-induced effect. In this case, the width of the space charge layer became rapidly higher than the half-thickness of the tube walls, when the applied potential increased. Therefore, the walls were progressively depleted under anodic polarisation, passing from a situation where the tubes were totally active in the cathodic range towards a situation where the contribution of the tube walls could be neglected.     

Correlation between structural and optical properties of TiO<Subscript>2</Subscript>:ZnO thin films prepared by sol–gel method

We have studied structural and optical properties of thin films of TiO₂, doped with 5% ZnO and deposited on glass substrate (by the sol–gel method). Dip-coated thin films have been examined at different annealing temperatures (350–450 °C) and for various layer thicknesses (89–289 nm). Refractive index, porosity and energy band gap were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range of 1.97–2.44, the porosity is in the range of 0.07–0.46 and the energy band gap is in the range of 3.32–3.43. The coefficient of transmission varies from 50 to 90%. In the case of the powder of TiO₂, doped with 5% ZnO, and aged for 3 months in ambient temperature, we have noticed the formation of the anatase phase (tetragonal structure with 20.23 nm grains). However, the undoped TiO₂ exhibits an amorphous phase. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 350 °C. The obtained structures are anatase and brookite. The calculated grain size, depending on the annealing temperature and the layer thickness, is in the range of 8.61–29.48 nm.     

Synthesis,structural and electrical characterization of PbS NCs in titania sol–gel films

Nanocrystals of lead sulfide were grown in TiO₂ (titania) thin films prepared by a sol-gel process. The synthetic procedure as well as the structural, optical, and electrical properties of the films are demonstrated. The structures and morphology of PbS nanocrystals were analyzed using HRTEM, SAED, AFM, HRSEM, XRD and EDAX elemental analysis technique. When the concentration of PbS in the titania matrix is 20 mol%, PbS NCs with a diameter of 2.0 nm are created. At a higher PbS concentration (> 40 mole%) in the titania matrix, PbS NCs and PbS clusters are created not only within the TiO₂ film but also on the external surface of the TiO₂ film. By increasing the PbS concentration up to 50 mol%, PbS nanocrystals of 6–8 nm in diameter are formed within the titania film and PbS clusters with a base size of about 100 nm² and a height up to about 20 nm were self assembled on the external surface of TiO₂ film. Quantum size effect and band gap energies were obtained from shifts of the absorption edge. For electrical measurements, PbS–TiO₂ films were deposited on an ITO/glass substrate, and then covered with gold contact. The electrical properties of ITO/PbS NCs–TiO₂/Au and ITO/PbS NCs–TiO₂/PbS cluster/Au structures were studied. I–V characteristics of the one layer structure are nearly linear and symmetric, while those of the two-layer structure exhibit rectifying behavior.     

Dielectric properties of Al–Si composite oxide films formed on electropolished and DC-etched aluminum by electrophoretic sol-gel coating and anodizing

Highly pure aluminum specimens (99.99%) after electropolishing and DC-etching were covered with SiO₂ films by electrophoretic sol-gel coating and were anodized in neutral boric acid/borate solutions. Time-variations in cell voltage during electrophoretic sol-gel coating and in anode potential during anodizing were monitored. Structure and dielectric properties of the anodic oxide films were examined by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray (EDX), and electrochemical impedance spectroscopy (EIS). It was found that electrophoretic sol-gel coating forms uniform SiO₂ films on the surface of both electropolished and DC-etched specimens. Anodizing of specimens after electrophoretic coating lead to the formation of anodic oxide films consisting of two layers: an inner alumina layer and an outer Al–Si composite oxide layer. The anodic oxide films formed, thus, had slightly higher capacitances than those formed on aluminum without any coating. Higher heating temperatures after electrophoretic deposition caused the increase in capacitance of anodic oxide films more effectively. Anodizing in a boric acid solution after SiO₂ coating on DC-etched foil allowed the anode potential to reach a value higher than 1,000 V, resulting in 39% higher capacitances than those on specimens without SiO₂ film. Dedicated to Professor Su-Il Pyun on the occasion of his 65th birthday.     

Light energy accumulation using Ti/RuO2 electrode as capacitor

In the present study, the possibility to use Ti/RuO₂ electrode as capacitor for storage of photoelectrons generated under UV irradiation in Ti/TiO₂ photoelectrode has been investigated. A light-sensitive TiO₂ layer has been formed by means of anodizing Ti electrode in the solution of 0.5 M H₂SO₄. A layer of RuO₂, exhibiting the properties of electrochemical capacitor, has been formed by means of thermal decomposition of RuOHCl₃ also on Ti substrate. The photocharging capability of RuO₂ has been studied by means of short-circuiting Ti/RuO₂ electrode with Ti/TiO₂ photoelectrode in deaerated solution of 0.1 M KOH. It has been shown that the intensity of photocurrent flowing from Ti/TiO₂ to Ti/RuO₂ electrode depends mainly on the potential of the latter. Maximum value of photocurrent density was ∼180 μA cm⁻², which corresponded to maximum value of photon-to-electron conversion efficiency (IPCE) of about 60%. The amount of photogenerated charge Q _ph, which can be stored, depends on the capacitance of RuO₂ coating. Under the conditions of the experiment, Q _ph ranged from ∼35 to ∼50 mC, which corresponded to a specific charge of RuO₂ coating ranging between ∼20 and ∼30 mAh g⁻¹.     

Evolution of an iron passive film in a borate buffer solution (pH 8.4)

The evolution under open-circuit conditions of iron passive films formed at 0.8 V_SCE in a borate buffer solution at pH 8.4 was investigated with electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. The composition of the freshly formed passive film as determined by X-ray photoelectron spectroscopy (XPS) was found to be in agreement with a bilayer model, where the inner layer is composed mainly of iron oxide and the outer layer consists of a hydrated material. Results of XPS measurements also showed that the open-circuit breakdown of passive films was consistent with a reductive dissolution mechanism. When the iron electrode reached an intermediate stage in the open-circuit potential decay (approximately −0.3 V_SCE), the oxide film, containing both Fe(II) and Fe(III), was still protective. The impedance response in this stage exhibited a mixed control by charge transfer at the metal/film and film/solution interfaces and diffusion of point defects through the film. At the final stage of the open-circuit potential decay (approximately −0.7 V_SCE), the oxide film was very thin, and the ratio of Fe³⁺/Fe²⁺ and O²⁻/OH⁻ had decreased significantly. The impedance response also exhibited a mixed charge-transfer–diffusion control, but the diffusion process was related to transport of species in the electrolyte solution resulting from dissolution of the oxide film.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.