Formation and characterization of conductive thin layers of copper sulfide (CuxS) on the surface of polyethylene and polyamide by the use of higher polythionic acids

Layers of copper sulfide of varying composition and properties are formed on the surface of polyethylene and polyamide by a sorption-diffusion method using solutions of higher polythionic acids, H₂S_nO₆. The concentration of sulfur adsorbed-diffused into PE and PA depends on the degree of the acid sulfurity, n, the temperature of the solution and the period of the polymer treatment. The amount of copper in a sulfide (Cu_xS) layer formed after the sulfured polymer treatment with a solution of Cu(I-II) salt is strongly dependent on the concentration of sulfur in the PE and PA. By the chemical analysis of the obtained sulfide layers was determined that a value of x in the Cu_xS layers varies in the interval 1 < x < 2. The microscopic investigation of transverse sections of PE and PA samples with copper sulfide layers showed that the major part of copper sulfide is in the surface matrix of the polymer. X-ray diffraction studies of the Cu_xS layers obtained seven phases: with x = 2 (chalcocite), 1.9375 (djurleite), 1.8 (digenite), 1.75 (anilite), 1.12 (yarrowite), 1.06 (talnakhite) and 1 (covellite). The measurements of the electrical conductance of Cu_xS layers (0.1-4 S cm⁻²) showed that its value greatly depends on the conditions of PE and PA interaction with H₂S_nO₆ and of further interaction with Cu(I-II) salt solution, on the chemical and phase composition of the layer.     

Optical and structural properties of CdS thin films grown by chemical bath deposition doped with Ag by ion exchange

In this work thin CdS films using glycine as a complexing agent were fabricated by chemical bath deposition and then doped with silver (Ag), by an ion exchange process with different concentrations of AgNO₃ solutions. The CdS films were immersed in silver solutions using different concentrations during 1 min for doping and after that the films were annealed at 200 °C during 20 min for dopant diffusion after the immersion on the AgNO₃ solutions. The aim of this research was to know the effects of different concentrations of Ag on the optical and structural properties of CdS thin films. The optical band gap of the doped films was determined by transmittance measurements, with the results of transmittance varying between 35% and 70% up to 450 nm in the electromagnetic spectra and the band gap varying between 2.31 and 2.51 eV depending of the silver content. X-ray photoelectron spectroscopy was used to study the influence of silver on the CdS:Ag films, as a function of the AgNO₃ solution concentration. The crystal structure of the thin CdS:Ag films was studied by the X-ray diffraction method and the film surface morphology was studied by atomic force microscopy. Using the ion exchange process, the CdS films’ structural, optical and electric characteristics were modified according to silver nitrate concentration used.     

Investigation of CdS and CdTe thin films and influence of CdCl2 on CdTe/CdS structure

CdTe/CdS heterojunction solar cell structure has been fabricated using simple, easy and low-cost methods. To fabricate this structure, CdS and CdTe thin films are deposited onto FTO-coated conducting glass substrates by chemical bath deposition (CBD) and electrodeposition method, respectively. The optimized growth conditions are chosen for both CdS and CdTe films by investigating the optical, structural and morphological properties of both the as-deposited and annealed films. Optical measurement showed that CdS films have higher transmittance and lower absorbance, and CdTe films have lower transmittance and higher absorbance in the near infrared region. The band gap of CdS films is estimated to lie in the range 2.29–2.41 eV and that of CdTe films is in the range 1.53–1.55 eV. X-ray diffraction (XRD) study reveals that CdS and CdTe films are polycrystalline with preferential orientation of (1 1 1) plane. Scanning electron microscopy (SEM) study reveals that both films are smooth, void-free and uniformly distributed over the surface of the substrate. Fabricated CdTe/CdS structure showed the anticipated rectifying behaviour, and the rectifying behaviour is observed to improve due to CdCl₂ treatment.     

CdS films deposited by chemical bath under rotation

Cadmium sulfide (CdS) films were deposited on rotating substrates by the chemical bath technique. The effects of the rotation speed on the morphological, optical, and structural properties of the films were discussed. A rotating substrate-holder was fabricated such that substrates can be taken out from the bath during the deposition. CdS films were deposited at different deposition times (10, 20, 30, 40 and 50 min) onto Corning glass substrates at different rotation velocities (150, 300, 450, and 600 rpm) during chemical deposition. The chemical bath was composed by CdCl₂, KOH, NH₄NO₃ and CS(NH₂)₂ as chemical reagents and heated at 75 °C. The results show no critical effects on the band gap energy and the surface roughness of the CdS films when the rotation speed changes. However, a linear increase on the deposition rate with the rotation energy was observed, meanwhile the stoichiometry was strongly affected by the rotation speed, resulting a better 1:1 Cd/S ratio as speed increases. Rotation effects may be of interest in industrial production of CdTe/CdS solar cells.     

Preparation and characterization of patterned copper sulfide thin films on n-type TiO2 film surfaces

Micro-arrayed patterns of p-type copper sulfide (Cu_xS) thin films with positive and negative features were deposited onto the surfaces of n-type TiO₂ semiconductor films via a selective nucleation and growth process from aqueous solution. The surface functional molecules of the UV photo-oxidised patterned SAMs were utilized to direct the nucleation and growth of Cu_xS crystallites. The resultant Cu_xS/TiO₂ composite films with negative and positive Cu_xS patterns on the TiO₂ film surface were investigated using SEM, XRD, XPS and a 3D Surface Profiler. It is demonstrated that regular and compact patterned films of Cu₂S crystallites had been deposited onto the n-type TiO₂ surface, with sharp edges demarcating the boundaries between the patterned Cu₂S region and the TiO₂ film region. The UV-vis spectra for three Cu₂S/TiO₂ films exhibit a wide absorption between 300 nm and 450 nm. The maximum wavelength differences in the spectra of Cu₂S/TiO₂ films and TiO₂ film were attributed to the added absorption of Cu₂S films at 302 nm and the unchanged adsorption of TiO₂ films. The absorption intensities of the Cu₂S/TiO₂ films could be varied in the UV-vis range using the Cu₂S patterned features (positive, negative).     

Synthesis of CdSe/CdS with a simple non-TOP-based route

A convenient and non-TOP-based route for the synthesis of core-shell CdSe/CdS quantum dots (QDs) is developed for the first time. Simple reagents, such as cadmium oxide, selenium powder, sodium sulfide, paraffin and oleic acid with obvious advantages are used to replace organometallics. This simple route allows the preparation of a series of core-shell CdSe/CdS QDs emitting in a wide wavelength range (from 510 to 615 nm). After passivation of CdSe by CdS shell using sodium sulfide as the source of sulfur at 80 °C, the quantum yields (QYs) are improved from 15-30% to 35-50% and remained stable at least for 4 months. A narrow bandwidth (FWHM<50 nm) indicates that the as-prepared QDs have uniform size distribution, desirable dispersibility and good fluorescence properties. The whole procedure can be carried out either open to air or under nitrogen atmosphere, which is simpler, greener and cheaper as compared with TOP-based route.     

Fabrication of highly luminescent InP/Cd and InP/CdS quantum dots

Highly luminescent InP/Cd and InP/CdS core-shell QDs were fabricated by sequential addition of cadmium acetylacetonate and dodecanethiol to InP core solutions, which showed a red-shift in absorption and emission. ICP measurement revealed the existence of cadmium and TEM images showed the increased size of InP/CdS QDs. PXRD data identified zinc blend structures of InP and InP/CdS QDs, which indexed to the (1 1 1), (2 2 0) and (3 1 1) planes. The slight shift of peaks between InP and InP/CdS QDs can demonstrate the existence of CdS shell structures.     

Effect of sintering aid (CdCl2) on the optical and structural properties of CdZnS screen-printed film

Sulphides of zinc and cadmium have been utilized effectively in various opto-electronic devices. In the present work cadmium zinc sulphide (Cd_0.4Zn_0.6S) thin film has been deposited on ultra clean glass substrate by a simple inexpensive screen-printing method using cadmium sulphide, zinc sulphide, anhydrous cadmium chloride and ethylene glycol. Cadmium chloride has been used as sintering aid and ethylene glycol as a binder. Effect of sintering aid on the optical and structural properties of prepared cadmium zinc sulphide film has been investigated. The optical band gap (E_g) of the film has been studied by using reflection spectra in wavelength range 325–600 nm. It is found that reflection spectra suffer a drastic fall at two places, which is indicative of two band gaps of film viz. 2.38 eV and 2.9 eV corresponding to CdS and Cd_0.6Zn_0.4S, respectively. This is suggestive of the fact that cadmium zinc sulphide is a wide band gap semiconducting material. X-ray diffraction also confirms the formation of Cd_0.6Zn_0.4S composition.     

TEM and XPS studies on CdS/CIGS interfaces

Copper indium gallium selenide (CIGS) was deposited by metallic precursors sputtering and subsequently submitted to a selenization process. The upper CdS layers were deposited by chemical bath deposition (CBD) technique. The CdS/CIGS interfaces were investigated by Transmission Electron Microscopy (TEM) and X-ray Photoelectron Spectroscopy (XPS). As checked by XPS analysis, the CIGS surface exhibited a hydroxide-terminated CdSe layer when treated with Cd Partial Electrolyte solution (Cd PE). Its thickness was roughly estimated to several nanometers. A 100 nm thick CdS layer was deposited onto CIGS surface. The TEM images revealed a clear and sharp interface between CdS and CIGS. XPS analysis showed a CIGS surface covered by a pinhole free and homogeneous CdS layer. XPS depth profile measurement of the CdS/CIGS interface did not evidence elemental inter-diffusion between the CIGS and CdS layers, in very good agreement with TEM observations.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Enhancement of output performance of Cu2ZnSnS4 thin film solar cells—A numerical simulation approach and comparison to experiments

The formation of stable, low resistance and nonrectifying contacts to Cu₂ZnSnS₄ (CZTS) thin film photovoltaic material are the major and critical challenges associated with its effect over the output performance of fabricated solar cells. The solution of continuity equation in one dimension for a soda lime glass substrates (SLG) |Mo | CZTS | CdS | ZnO:Al cell structure is considered in the simulation of its current–voltage characteristics that is governed by the back contact material, acceptor concentration as well as thickness of the CZTS layer. Our primary simulation shows a 6.44% efficiency of the CZTS solar cell which is comparable to reported experimental data if these parameters are not optimized. However, by optimizing them a simulated conversion efficiency as high as 13.41% (V_oc=1.002 V, J_sc=19.31 mA/cm², fill factor (FF)=69.35%) could be achievable. The solar cell with a back contact metal work function of 5.5 eV, an absorber layer's thickness of 2.68 μm and an acceptor concentration of 5×10¹⁶ cm⁻³ were optimum. The presented optimization is ideal and subject to experimental verification with a precise control of the process parameters along with reduced surface as well as bulk recombination, secondary phases and thermalization losses.     

Structural, optical and photoelectrochemical characterization of CdS nanowire synthesized by chemical bath deposition and wet chemical etching

Nanocrystalline thin films of CdS have been grown onto flexible plastic and titanium substrates by a simple and environmentally benign chemical bath deposition (CBD) method at room temperature. The films consist of clusters of CdS nanoparticles. The clusters of CdS nanoparticles in the films were successfully converted into nanowire (NW) networks using chemical etching process. The possible mechanism of the etching phenomenon is discussed. These films were examined for their structural, surface morphological and optical properties by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and UV-vis spectrophotometry techniques, respectively. Photoelectrochemical (PEC) investigations were carried out using cell configuration as n-CdS/(1 M NaOH + 1 M Na₂S + 1 M S)/C. The film of nanowires was found to be hexagonal in structure with the preferential orientation along the (0 0 2) plane. The nanowires have widths in the range of 50-150 nm and have lengths of the order of a few micrometers. Optical studies reveal that the CdS nanowires have value of band gap 2.48 eV, whereas it is 2.58 eV for nanoparticles of CdS. Finally, we report on the ideality of junction improvement of PEC cells when CdS nanoparticles photoelectrode converted into nanowires photoelectrode.     

Synthesis and characterization of Zn(O,OH)S and AgInS2 layers to be used in thin film solar cells

In this paper AgInS₂ and Zn(O,OH)S thin films were synthesized and characterized. AgInS₂ layers were grown by co-evaporation from metal precursors in a two-step process, and, Zn(O,OH)S thin films were deposited from chemical bath containing thiourea, zinc acetate, sodium citrate and ammonia. X-ray diffraction measurements indicated that AgInS₂ thin films grown with chalcopyrite structure, and the as-grown Zn(O,OH)S thin films were polycrystalline. It was also found that the AgInS₂ films presented p-type conductivity, a high absorption coefficient (greater than 10⁴ cm⁻¹) and energy band-gap E_g of about 1.95 eV, Zn(O,OH),S thin films presented E_g of about 3.89 eV. Morphological analysis showed that under this synthesis conditions Zn(O,OH),S thin films coated uniformly the absorber layer. Additionally, the Zn(O,OH)S kinetic growth on AgInS₂ layer was studied also. Finally, the results suggest that these layers possibly could be used in one-junction solar cells and/or as top cell in a tandem solar cell.     

Analysis of chemical dissolution of the barrier layer of porous oxide on aluminum thin films using a re-anodizing technique

Chemical dissolution of the barrier layer of porous oxide formed on thin aluminum films (99.9% purity) in the 4% oxalic acid after immersion in 2 mol dm⁻³ sulphuric acid at 50 °C has been studied. The barrier layer thickness before and after dissolution was calculated using a re-anodizing technique. It has been shown that above 57 V the change in the growth mechanism of porous alumina films takes place. As a result, the change in the amount of regions in the barrier oxide with different dissolution rates is observed. The barrier oxide contains two layers at 50 V: the outer layer with the highest dissolution rate and the inner layer with a low dissolution rate. Above 60 V the barrier oxide contains three layers: the outer layer with a high dissolution rate, the middle layer with the highest dissolution rate and the inner layer with a low dissolution rate. We suggest that the formation of the outer layer of barrier oxide with a high dissolution rate is linked with the injection of protons or H₃O⁺ ions from the electrolyte into the oxide film at the anodizing voltages above 57 V.     

Theoretical investigation of Cu-containing materials with different valence structure types: BaCu2S2, Li2CuSb,and LiCuS

Optoelectronics research requires cheap materials with a broad spectrum of optical, electronic, and structural properties. The class of Heusler compounds and ternary structures provide many possibilities for finding alternative group IV and III–V semiconductor compounds. This study introduces wider band gap materials for use in solar cells as an alternative to cadmium sulfide buffer layers. The buffer layer is inserted between the absorber layer (p-type) and the transparent window layer (n-type) to enhance the maximum amount of light transmission. Reasonable calculations are reported for the band gaps of copper-containing materials: LiCuS, BaCu₂S₂, and Li₂CuSb. Previous optical analysis measurements of these films determined that the band gaps were 1.8 and 1.9 eV for BaCu₂S₂ and LiCuS, respectively. In general, semiconductor compounds have been studied theoretically, but there are major differences between the experimental and theoretically calculated band gaps. A suitable calculation method for semiconductor compounds is described in this study. For the first time, calculations based on the Engel and Vosko method are introduced for these semiconductor compounds. This method yields band gaps that are comparable to the experimental values, which facilitate the development of microscopic analyses of these compounds. Direct band gaps of 1.15 and 1.7 eV were obtained for BaCu₂S₂ and LiCuS, respectively, whereas the indirect band gap was 0.7 eV for Li₂CuSb.     

Optical properties of cadmium sulfide nanocrystal film prepared by electrochemical synthesis at liquid-liquid interface

Dendritic nanocrystalline CdS film was deposited at liquid-liquid interface of surfactants and an electrolyte containing 4 mmol L⁻¹ cadmium chloride (CdCl₂) and 16 mmol L⁻¹ thioacetamide (CH₃CSNH₂) with an initial pH value of 5 at 15 °C by electrochemical synthesis. The nanofilm was characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), ultraviolet visible (UV-vis) absorption spectroscopy and fluorescence spectroscopy. The surface morphology and particle size of the nanofilm were investigated by AFM, SEM and TEM, and the crystalline size was 30-50 nm. The thickness of the nanofilm calculated by optical absorption spectrum was 80 nm. The microstructure and composition of the nanofilm was investigated by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), showing its polycrystalline structure consisting of CdS and Cd. Optical properties of the nanofilm were investigated systematically by UV-vis absorption and fluorescence spectroscopy. A λ_onset blue shift compared with bulk CdS was observed in the absorption spectra. Fluorescence spectra of the nanofilm indicated that the CdS nanofilm emitted blue and green light. The nanocomposites film electrode will bring about anodic photocurrent during illumination, showing that the transfer of cavities produces photocurrent.     

Synthesis, characterization and photoelectrochemical properties of n-CdS thin films

Cadmium sulfide thin films have been deposited on glass substrates by simple and cost effective chemical bath deposition technique. Triethanolamine was used as a complexing agent. The preparative parameters like ion concentration, temperature, pH, speed of substrate rotation and deposition time have been optimized for good quality thin films. The ‘as-grown’ films are characterized for structural, electrical, optical and photoelectrochemical (PEC) properties. The X-ray diffraction (XRD) studies reveal that the films are polycrystalline in nature. Energy-dispersive analysis by X-ray (EDAX) shows that films are cadmium rich. Uniform deposition of CdS thin films on glass substrate is observed from scanning electron microscopy (SEM) and atomic force microscopy (AFM) micrographs. Optical studies reveal a high absorption coefficient (10⁴ cm⁻¹) with a direct type of transition. The band gap is estimated to be 2.47 eV. The film shows n-type conduction mechanism. The photoelectrochemical (PEC) cell with CdS thin film as a photoanode and sulfide/polysulfide (1 M) solution as an electrolyte have been constructed and investigated for various cell parameters. The solar to electrical conversion efficiency (η) and fill factor (ff) are found to be 0.049% and 0.36, respectively.     

Depth-dependent fct to fcc strain relaxation in CoxNi1−x/Cu3Au(1 0 0) alloy films

Co_xNi_1−x/Cu₃Au(1 0 0) with x ? 11% was prepared at room temperature to study the strain relaxation and their correlation with the spin-reorientation transition. The vertical interlayer distance relaxed from 1.66 Å (fct) to 1.76 Å (fcc) while the thickness increased from 8 ML to 18 ML. Such rapid strain relaxation with thickness was attributed to the larger lattice mismatch between Co_xNi_1−x and Cu₃Au(1 0 0) (η ∼ −6.5%). The smooth change for crystalline structure was observed during strain relaxation process in which the crystalline structure seems irrespective of the alloy composition. To explain the strain relaxation, a phenomenological model was proposed. We provide a physical picture that the deeper layers may not relax while the surface layer start to relax. This assumption is based on the several experimental studies. Using the strain averaged from all layers of thin film as the volume strain of magneto-elastic anisotropy energy, the interrelation between strain relaxation and spin reorientation transition can be well described in a Néel type magneto-elastic model.     

Formation of GaAs1−xNx nanofilm on GaAs by low energy N2 implantation

Nitridation of GaAs (1 0 0) by N₂⁺ ions with energy E_i = 2500 eV has been studied by Auger- and Electron Energy Loss Spectroscopy under experimental conditions, when electrons ejected only by nitrated layer, without contribution of GaAs substrate, were collected. Diagnostics for quantitative chemical analysis of the nitrated layers has been developed using the values of NKVV Auger energies in GaN and GaAsN chemical phases measured in one experiment, with the accuracy being sufficient for separating their contributions into the experimental spectrum. The conducted analysis has shown that nanofilm with the thickness of about 4 nm was fabricated, consisting mainly of dilute alloy GaAs_1−xN_x with high concentration of nitrogen x ∼ 0.09, although the major part of the implanted nitrogen atoms are contained in GaN inclusions. It was assumed that secondary ion cascades generated by implanted ions play an important role in forming nitrogen-rich alloy.     

Optimisation of the CBD CdS deposition parameters for ZnO/CdS/CuGaSe2/Mo solar cells

We present an optimisation of our recipe for the CdS chemical bath deposition process as applied to solar cells based on polycrystalline CuGaSe₂ (CGSe) absorber layers prepared in two stages by physical vapour deposition. We investigate the influence of the ammonia (NH₃) and the thiourea (H₂NCSNH₂) concentration, both being constituents of the chemical bath deposition (CBD) solution, at a deposition temperature of 80 °C on the microstructural and optical properties of CdS layers and on ZnO/CdS/CuGaSe₂/Mo device parameters. The composition of the CdS layers and their thickness were determined using X-ray Fluorescence Analysis. Transmission and reflection measurements performed at 300 K were used for the calculation of absorption and optical band gap energy (E_g). The E_g values of the films varied from 2.41 to 2.46 eV depending on deposition conditions. Cubic phase of the as-grown layers was identified by X-ray diffraction analysis. An improvement in the investigated solar cells efficiency was achieved when the ammonia concentration was increased and the thiourea concentration was reduced, compared to the previously used standard HMI recipe. The influence of the CBD CdS preparation recipe on the ZnO/CdS/CuGaSe₂/Mo electrical and photoelectrical properties is discussed.