Synthesis and gas barrier characterization of poly(ethylene isophthalate)

Poly(ethylene isophthalate) (PEI) was synthesized for this research with essentially a condensation polymerization of isophthalic acid and ethylene glycol catalyzed by zinc acetate and antimony trioxide. Several samples were obtained, and their characteristics were observed and compared with poly(ethylene terephthalate) (PET). The synthesized PEI samples were chemically identified by ¹H NMR. Thermal analysis with differential scanning calorimetry (DSC) yielded results that indicate the samples were primarily amorphous, with a glass‐transition temperature of 55–60 °C. Molecular weights of these PEI samples were also obtained through intrinsic viscosity measurements (Mark–Houwink equation). Molecular weights varied with conditions of the polymerization, and the highest molecular weight achieved was 21,000 g/mol. Finally, the diffusion coefficient, solubility, and permeability of CO₂ gas in PEI were measured and found to be substantially lower than in PET, as anticipated from their isomeric chemical structures. This is because in PET the phenyl rings are substituted in the para (1,4) positions, which allows for their facile flipping, effectively permitting gases to pass through. However, the meta‐substituted phenyl rings in PEI do not permit such ring flipping, and thus PEI may be more suitable for barrier applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4247–4254, 2004     

Poly(ethylene terephthalate) copolymers containing 5‐tert‐butyl isophthalic units

Poly(ethylene terephthalate‐co‐5‐tert‐butyl isophthalate) copolymers, abbreviated as PET^tBI, with compositions ranging between 95/5 and 25/75, as well as the two parent homopolymers, PET and PE^tBI, were prepared from comonomer mixtures by a two‐step melt‐polycondensation. Polymer intrinsic viscosities varied from 0.4 to 0.7 dL g^?1 with weight‐average molecular weights ranging between 31,000 and 80,000. The copolymers were found to have a random microstructure with a composition according to that used in the corresponding feed. The melting temperature and crystallinity of PET^tBI decreased with the content in 5‐tert‐butyl isophthalic units, whereas the glass‐transition temperature increased from 82 °C for PET up to 99 °C for PE^tBI. Copolymerization slightly improved the thermal stability of PET. Preliminary X‐ray diffraction studies revealed that PET^tBI adopt the same crystal structure as PET with the alkylated isophthalic units probably excluded from the crystal lattice. The homopolymer PE^tBI appeared to be a highly crystalline polymer taking up a crystal structure clearly different from that of PET and PET^tBI copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 1994–2004, 2001     

Poly(ethylene‐co‐1,4‐cyclohexylenedimethylene terephthalate) copolyesters obtained by ring opening polymerization

Cyclic oligomer fractions of ethylene terephthalate c(ET)_n and 1,4‐cyclohexylenedimethylene terephthalate c(CT)_n were obtained by cyclodepolymerization of their respective polyesters, the former containing around 80 mol % of trimer and the latter with around 70 mol % of trimer to pentamer. Mixtures of these fractions at selected compositions were subjected to ring opening copolymerization to give a series of poly(ethylene‐co‐cyclohexylenedimethylene terephthalate) copolyesters with ET/CT comonomer ratios ranging from 90/10 to 10/90. The copolyesters were characterized by GPC and NMR, and their thermal properties were evaluated by DSC and TGA. They had essentially the same composition as the feed from which they were produced and had an average‐weight molecular weights between 30,000 and 40,000 g/mol with polydispersities between 2 and 2.7. The distribution of the monomeric units in these copolyesters was essentially at random although it evolved to be a blocky microstructure as the contents in the two comonomers became more dissimilar. Their thermal behavior was the expected one for these types of copolyesters with crystallinity and heating stability decreasing with the content in CT units. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5954–5966, 2009     

Synthesis,characterization, and properties of hydroxyl‐terminated copolysiloxanes containing γ‐cyanopropyl groups

A series of random copolysiloxanes (PCDMS) containing various amount of γ‐cyanopropyl groups are prepared by a new method under mild conditions. Structures of the synthesized polymers are fully characterized by FTIR, ¹H NMR, ²⁹Si NMR, and GPC. Rheological properties of PCDMS are tested by cone and plate rheometer, and thermal properties by differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA). Damping properties as well as fuel resistance of the cured PCDMS elastomers are also tested. The correlation between chemical structure, content of cyanopropyl group and properties are discussed. With the increasing amount of polar cyanopropyl group introduced, glass transition temperatures (T_g) of the synthesized PCDMS gradually increases from ?121 to ?65 °C, residual weight increases from 0 to 36% at 800°C, loss factor reaches as high as 1.74, mass increase under fuel immersion for 14 days can be as low as 3.6%. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1408–1421     

Morphology of poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) segmented copolyesters

Segmented copolyesters, namely, poly(butylene terephthalate)–poly(ethylene terephthalate‐co‐isophthalate‐co‐sebacate) (PBT‐PETIS), were synthesized with the melting transesterification processing in vacuo condition involving bulk polyester produced on a large scale (PBT) and ternary amorphous random copolyester (PETIS). Investigations on the morphology of segmented copolyesters were undertaken. The two‐phase morphology model was confirmed by transmission electron microscopy and dynamic mechanical thermal analysis. One of the phases was composed of crystallizable PBT, and the other was a homogeneous mixture of PETIS and noncrystallizable PBT. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2257–2263, 2003     

Carbohydrate‐based copolyesters made from bicyclic acetalized galactaric acid

Mixtures of the dimethyl esters of adipic acid and 2,3:4,5‐di‐O‐methylene‐galactaric acid (Galx) were made to react in the melt with either 1,6‐hexanediol or 1,12‐dodecanediol to produce linear polycyclic copolyesters with aldarate unit contents varying from 10 up to 90 mole %. The copolyesters had weight–average molecular weights in the ～35,000–45,000 g mol^?1 range and a random microstructure, and were thermally stable up to nearly 300 °C. They displayed T_g in the ‐50 to ‐7 °C range with values largely increasing with the content in galactarate units. All the copolyesters were semicrystalline with T_m between 20 and 90 °C but only those made from 1,12‐dodecanediol were able to crystallize from the melt at a crystallization rate that decreased as the contents in the two comonomers approached each other. Copolyesters containing minor amounts of galactarate units adopted the crystal structure characteristic of aliphatic polyesters but a new crystal polymorph was formed when the cyclic sugar units became the majority. Stress–strain parameters were sensitively affected by composition of the copolyesters with the mechanical behavior changing from flexible/ductile to stiff/brittle with the replacement of adipate units by the galactarate units. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Development of amorphous copolyesters based on 1,4‐cyclohexanedimethanol

The modification of poly(ethylene terephthalate) with 1,4‐cyclohexanedimethanol and the modification of poly(1,4‐cyclohexylenedimethylene terephthalate) with ethylene glycol or isophthalic acid retard the crystallization of the copolyester backbone, and over a wide range of comonomer concentrations, very slowly crystallizing, essentially amorphous copolyesters are formed. These amorphous copolyesters possess attractive physical properties such as toughness, low color, and chemical resistance, and since their first commercial introduction in 1977, these copolyesters have become the basis of a large and growing plastics business for Eastman Chemical Co. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5847–5852, 2004     

Blocky poly(ɛ‐caprolactone‐co‐butylene 2,5‐furandicarboxylate) copolyesters via enzymatic ring opening polymerization

Cyclic oligo(butylene 2,5‐furandicarboxylate) and ɛ‐caprolactone were copolymerized in bulk at 130–150 °C by enzymatic ring opening polymerization using CALB as catalyst. Copolyesters within a wide range of compositions were thus synthesized with weight‐average molecular weights between 20,000 and 50,000, the highest values being obtained for equimolar or nearly equimolar contents in the two components. The copolyesters consisted of a blocky distribution of the ɛ‐oxycaproate (CL) and butylene furanoate (BF) units that could be further randomized by heating treatment. The thermal stability of these copolyesters was comparable to those of the parent homopolyesters (PBF and PCL), and they all showed crystallinity in more or less degree depending on composition. Their melting and glass‐transition temperatures were ranging between those of PBF and PCL with values increasing almost linearly with the content in BF units. The ability of these copolyesters for crystallizing from the melt was evaluated by comparative isothermal crystallization and found to be favored by the presence of flexible ɛ‐oxycaproate blocks. These copolyesters are essentially insensitive to hydrolysis in neutral aqueous medium but they became noticeably degraded by lipases in an extend that increased with the content in CL units. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 290–299     

Photocrosslinkable copolyesters: Poly(alkylene terephthalate‐co‐1,4‐phenylene bisacrylate)

1,4‐Phenylene bis(acrylic acid) is a thermally stable diacid, which can be incorporated into polyesters. The phenylene bisacrylate structural units undergo rapid photochemical reaction in the solid state to form crosslinks. This constitutes a feasible approach to polyesters, which can be photochemically thermoset after fabrication as films and fibers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2167–2176, 2000     

Novel C60‐Anchored Two‐Armed Poly(tert‐butyl acrylate): Synthesis and Characterization

Summary: A multistep synthetic procedure for preparing novel C₆₀‐anchored two‐armed poly(tert‐butyl acrylate) was developed. First, two‐armed poly(tert‐butyl acrylate) bearing a malonate ester core with well‐controlled molecular weight was synthesized through atom transfer radical polymerization. The effective Bingel reaction between C₆₀ and the well‐defined polymer was then carried out to yield C₆₀‐anchored polymer. GPC, ¹H NMR, and UV‐vis spectroscopy indicated that the C₆₀‐anchored polymer was a monosubstituted and ‘closed’ 6,6‐ring‐bridged methanofullerene derivative.

Schematic of a novel C₆₀‐anchored two‐armed polymer.     

Poly(methyl methacrylate‐co‐pentaerythritol tetraacrylate‐co‐butyl methacrylate)‐g‐polystyrene: Synthesis and high oil‐absorption property

Well‐defined high oil‐absorption resin was successfully prepared via living radical polymerization on surface of polystyrene resin‐supported N‐chlorosulfonamide group utilizing methyl methacrylate and butyl methacrylate as monomers, ferric trichloride/iminodiacetic acid (FeCl₃/IDA) as catalyst system, pentaerythritol tetraacrylate as crosslinker, and L ‐ascorbic acid as reducing agent. The polymerization proceeded in a “living” polymerization manner as indicated by linearity kinetic plot of the polymerization. Effects of crosslinker, catalyst, macroinitiator, reducing agent on polymerization and absorption property were discussed in detail. The chemical structure of sorbent was determined by FTIR spectrometry. The oil‐absorption resin shows a toluene absorption capacity of 21 g g^?1. The adsorption of oil behaves as pseudo‐first‐order kinetic model rather than pseudo‐second‐order kinetic model. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and properties of amphiphilic and biodegradable poly(ε‐caprolactone‐co‐glycidol) copolymers

We have synthesized poly(ε‐caprolactone‐co‐tert‐butyl glycidyl ether) (CL‐co‐BGE) statistical copolymers using 1‐tert‐butyl‐4,4,4‐tris(dimethylamino)‐2,2‐bis [tris(dimethylamino)phophoranylidenamino]‐2Λ5,4Λ5‐catenadi(phosphazene) (t‐BuP₄) as the catalyst. The hydrolysis of the resulting polymers yields amphiphilic poly(ε‐caprolactone‐co‐glycidol) (CL‐co‐GD) copolymers. By use of the quartz crystal microbalance with dissipation (QCM‐D), we have investigated the enzymatic degradation of the copolymers. It is shown that the degradation rate increases with the content of hydrophilic (GD) units. (3‐(4,5‐Dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide) (MTT) assay experiments demonstrate that the CL‐co‐GD copolymers have low cytotoxicity. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 846–853     

Preparation,characterization, and thermal properties of alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,3‐bis(ethylene)permethyloligosiloxanylene]s

alt‐Copoly[1,9‐decaphenylpentasiloxanylene/1,3‐bis(ethylene)tetramethyldisiloxanylene], alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,5‐bis(ethylene)hexamethyltrisiloxanylene], alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,7‐bis(ethylene)octamethyltetrasiloxanylene], and alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,9‐bis(ethylene)decamethylpentasiloxanylene] were synthesized by Pt‐catalyzed hydrosilylation reactions of 1,9 divinyldecaphenylpentasiloxanes with a series of oligodimethylsiloxanes. The molecular weights of these copolymers were determined by gel permeation chromatography. Their glass‐transition temperatures (T_g's) were obtained by differential scanning calorimetry. The thermal stabilities of the copolymers were measured by thermogravimetric analysis. The structures of the copolymers were verified by ¹H, ¹³C, and ²⁹Si NMR as well as IR and UV spectroscopy. The copolymers displayed high thermal stabilities and a single T_g, indicating that phase separation between the two short blocks did not occur. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6146–6152, 2005     

Functional Polyolefins: Poly(ethylene)‐graft‐Poly(tert‐butyl acrylate) via Atom Transfer Radical Polymerization From a Polybrominated Alkane

Poly(cis‐cyclooctene) is synthesized via ring‐opening metathesis polymerization in the presence of a chain‐transfer agent and quantitatively hydrobrominated. Subsequent graft polymerization of tert‐butyl acrylate (tBA) via Cu‐catalyzed atom transfer radical polymerization (ATRP) from the non‐activated secondary alkyl bromide moieties finally results in PE‐g‐PtBA copolymer brushes. By varying the reaction conditions, a series of well‐defined graft copolymers with different graft densities and graft lengths are prepared. The maximum extent of grafting in terms of bromoalkyl groups involved is approximately 80 mol%. DSC measurements on the obtained graft copolymers reveal a decrease in T_m with increasing grafting density.     

Partially bio‐based poly(amide imide)s by polycondensation of aromatic diacylhydrazides based on lignin‐derived phenolic acids and aromatic dianhydrides: Synthesis,characterization, and computational studies

Two new bio‐based diacylhydrazide monomers, namely, 4,4′‐(propane‐1,3‐diylbis(oxy))bis(3‐methoxybenzohydrazide) and 4,4′‐(propane‐1,3‐diylbis(oxy))bis(3,5‐dimethoxybenzohydrazide) were synthesized starting from lignin‐derived phenolic acids, namely, vanillic acid and syringic acid. A series of poly(amide imide)s was synthesized by polycondensation of these diacylhydrazide monomers with commercially available aromatic dianhydrides. Poly(amide imide)s showed inherent viscosity in the range 0.44–0.56 dL g^?1 and exhibited good solubility in organic solvents. Poly(amide imide)s could be cast into transparent, flexible, and tough films from their N ,N‐dimethylacetamide solutions. Poly(amide imide)s showed 10% weight loss in the temperature range 340–364 °C indicating their good thermal stability. Glass transition temperature (T _g) of poly(amide imides)s were measured by DSC and DMA which were in the range 201–223 °C and 214–248 °C, respectively. The T _g values of poly(amide imide)s were dependent on the number methoxy substituents on aromatic rings of diacylhydrazide monomers. Molecular dynamics simulation studies revealed that chain rigidity is the dominant factor for observed trends in T _g. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3636–3645     

Synthesis and characterization of multiblock copolymers composed of poly(5‐methyl‐5‐benzyloxycarbonyl‐1,3‐dioxan‐2‐one) outer blocks and poly(L‐lactide) inner blocks

Ethylene glycol (EG) initiated, hydroxyl‐telechelic poly(L ‐lactide) (PLLA) was employed as a macroinitiator in the presence of a stannous octoate catalyst in the ring‐opening polymerization of 5‐methyl‐5‐benzyloxycarbonyl‐1,3‐dioxan‐2‐one (MBC) with the goal of creating A–B–A‐type block copolymers having polycarbonate outer blocks and a polyester center block. Because of transesterification reactions involving the PLLA block, multiblock copolymers of the A–(B–A)_n–B–A type were actually obtained, where A is poly(5‐methyl‐5‐benzyloxycarbonyl‐1,3‐dioxan‐2‐one), B is PLLA, and n is greater than 0. ¹H and ¹³C NMR spectroscopy of the product copolymers yielded evidence of the multiblock structure and provided the lactide sequence length. For a PLLA macroinitiator with a number‐average molecular weight of 2500 g/mol, the product block copolymer had an n value of 0.8 and an average lactide sequence length (consecutive C₆H₈O₄ units uninterrupted by either an EG or MBC unit) of 6.1. For a PLLA macroinitiator with a number‐average molecular weight of 14,400 g/mol, n was 18, and the average lactide sequence length was 5.0. Additional evidence of the block copolymer architecture was revealed through the retention of PLLA crystallinity as measured by differential scanning calorimetry and wide‐angle X‐ray diffraction. Multiblock copolymers with PLLA crystallinity could be achieved only with isolated PLLA macroinitiators; sequential addition of MBC to high‐conversion L ‐lactide polymerizations resulted in excessive randomization, presumably because of residual L ‐lactide monomer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6817–6835, 2006     

Fast degradable poly(L‐lactide‐co‐ε‐caprolactone) microspheres for tissue engineering: Synthesis,characterization, and degradation behavior

Polymeric scaffolds play a crucial role in engineering process of new tissues and effect the cell growth and viability. PLCL copolymers are found to be very useful during cell growth due to their elastic behavior and mechanical strength. Thus, low molecular weight PLCL copolymers of various ratios viz. PLCL(90/10), PLCL(75/25), PLCL(50/50) and PCL were synthesized by ring opening polymerization using stannous octoate as a catalyst. Synthesized polymers were characterized by GPC, ¹H‐NMR, FTIR and XRD. The thermal properties of the copolymers were studied using TGA and DSC. Microspheres of about 100 μm diameter were prepared for different copolymers and their in vitro degradation behaviors were studied up to 108 days. It was observed that degradation of PLA content in polymer backbone occurs faster than PCL component which is also indicated by corresponding change in ratios of PLA/PCL, as determined by ¹H‐NMR. SEM images of microspheres depicted the surface morphology during degradation and suggested the faster degradation for PLCL (50:50). Copolymers of different thermal, mechanical properties and different degradation behaviors can be prepared by adjusting the composition of copolymers. Various synthesized polymers from this work have been tested in our laboratory as polymeric scaffold for soft tissue engineering. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2755–2764, 2007     

Mechanism of Enzymatic Hydrolysis of Poly(butylene succinate) and Poly(butylene succinate‐co‐L‐lactate) with a Lipase from Pseudomonas cepacia

Enzymatic hydrolysis of poly(butylene succinate) (PBS) and poly(butylene succinate‐co‐L ‐lactate) (PBSL) has been studied by using a lipase originated from Pseudomonas cepacia. It has been found that the drawn fibers of PBSL are readily hydrolyzed by the action of the lipase, while those of PBS undergo little enzymatic hydrolysis. Since the polymer films of PBS and PBSL are readily hydrolyzed under the same conditions, the enzymatic hydrolysis should depend not only on the crystallinity but also on the molecular orientation. The molecular weight of the samples gradually decreases with incubation time, because nonspecific hydrolysis occurs on the main chains of both PBS and PBSL even in the absence of lipase. The enzymatic hydrolysis of PBS and PBSL gives 4‐hydroxybutyl succinate (HBS) as the main product with traces of succinic acid and butane‐1,4‐diol together with L ‐lactic acid in the case of PBSL. In addition, the hydrolysis rate of the carboxyl end‐capped PBS is much slower than that of the original or hydroxyl end‐capped PBS. These results imply a hydrolysis mechanism involving the preferential exo‐type chain scission from the carboxyl terminals.

Mass remaining of various PBS and PBSL samples as a function of time.     

Crystallization of poly(ethylene terephthalate–co–isophthalate)

Melt crystallization behaviors of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐isophthalate) (PETI) containing 2 and 12 mol % of noncrystallizable isophthalate components were investigated. Differential scanning calorimetry (DSC) isothermal results revealed that the introduction of 2 mol % isophthalate into PET caused a change of the crystal growth process from a two‐dimensional to a three‐dimensional spherulitic growth. The addition of more isophthalate up to 12 mol % into the PET structure induced a change in the crystal growth from a three‐dimensional to a two‐dimensional crystal growth. DSC heating scans after completion of isothermal crystallization at various T_c's showed three melting endotherms for PET and four melting endotherms for PETI‐2 and PETI‐12. The presence of an additional melting endotherm is attributed to the melting of copolyester crystallite composed of ethylene glycol, tere‐phthalate, and isophthalate (IPA) or the melting of molecular chains near IPA formed by melting the secondary crystallite T_m (I) and then recrystallizing during heating. Analyses of both Avrami and Lauritzen‐Hoffman equations revealed that PETI containing 2 mol % of isophthalate had the highest Avrami exponent n, growth rate constant G_o, and product of lateral and end surface free energies σσ_e. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2515–2524, 2000