Preparation and cryogenic mechanical properties of epoxy resins modified by poly(ethersulfone)

A thermoplastic, poly(ethersulfone) (PES) was used to modify a bisphenol‐F based epoxy resin cured with an aromatic diamine. The initial mixtures before curing, prepared by melt mixing, were homogeneous. Scanning electron microscopy (SEM) micrographs of solvent‐etched fracture surfaces of the cured blends indicated that phase separation occurred after curing. The cryogenic mechanical behaviors of the epoxy resins were studied in terms of tensile properties and Charpy impact strength at cryogenic temperature (77 K) and compared to their corresponding behaviors at room temperature (RT). The addition of PES generally improved the tensile strength, elongation at break, and impact strength at both RT and 77 K except the RT tensile strength at 25 phr PES content. It was interesting to observe that and the maximum values of the tensile strength, elongation at break, and impact strength occurred at 20 phr PES content where a co‐continuous phase formed. Young's modulus decreased slightly with the increase of the PES content. Moreover, the tensile strength and Young's modulus at 77 K were higher than those at RT at the same composition, whereas the elongation at break and impact strength showed the opposite results. Finally, the differential scanning calorimetry analysis showed that the glass transition temperature (T_g) was enhanced by the addition of PES. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 612–624, 2008     

Effect of surface modification of colloidal silica nanoparticles on the rigid amorphous fraction and mechanical properties of amorphous polyurethane–urea–silica nanocomposites

Colloidal silica nanoparticles (NPs) modified with eight different silane coupling agents were incorporated into an amorphous poly(tetramethylene oxide)‐based polyurethane–urea copolymer matrix at a concentration of 10 wt % (4.4 vol %) in order to investigate the effect of their surface chemistry on the structure–property behavior of the resulting nanocomposites. The rigid amorphous fraction (RAF) of the nanocomposite matrix as determined by differential scanning calorimetry and dynamic mechanical analysis was confirmed to vary significantly with the surface chemistry of the NPs and to be strongly correlated with the bulk mechanical properties in simple tension. Hence, nanocomposites with an RAF of about 30 wt % showed a 120% increase in Young's modulus, a 25% increase in tensile strength, a 15% decrease in elongation at break with respect to the neat matrix, which had no detectable RAF, whereas nanocomposites with an RAF of less than 5% showed a 60% increase in Young's modulus, a 10% increase in tensile strength and a 5% decrease in the elongation at break. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2543–2556     

Effects of humidity on Young's modulus in poly(methyl methacrylate)

Tensile tests on poly (methyl methacrylate) (PMMA) were conducted to clarify the effects of humidity and strain rate on tensile properties, particularly Young's modulus. Prior to the tensile tests, specimens were kept under various humidity conditions at 293 K, which were the same as the test conditions, for a few months to adjust the sorbed water content in the specimens. The tensile tests were performed under each humidity condition at three different strain rates (approximately 1.4 × 10^?3, 1.4 × 10^?4, and 1.4 × 10^?5 s^?1). Stress‐strain curves changed with humidity and strain rate. Young's moduli were also measured at small applied stresses (below 6.7 MPa) under various humidity conditions at 293 K. Young's modulus decreases linearly with increasing humidity and a decreasing logarithm of strain rate. These results suggest that Young's modulus of PMMA can be expressed as a function of two independent parameters that are humidity and strain rate. A constitutive equation for Young's modulus of PMMA was proposed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 460–465, 2002; DOI 10.1002/polb.10107     

Tensile and flexural properties of polypropylene composites filled with highly effective flame retardant magnesium hydroxide

The reinforcing effects of highly effective flame retardant magnesium hydroxide (FMX) content on the tensile and flexural properties of filled polypropylene (PP) composites were investigated within the FMX weight fraction range from 5 to 60 wt%. It was found that the Young's modulus and flexural modulus increased approximately linearly while the tensile yield strength and tensile fracture strength decreased slightly with increasing the FMX weight fraction. When the FMX weight fraction was lower than 20%, the tensile elongation at break decreased considerably, and then decreased slightly; the flexural strength increased when the FMX weight fraction was lower than 30%, and then decreased slightly. The tensile properties increased with increasing rate of tension. Moreover, the tensile yield strength of the composites was estimated using an equation proposed in previous work, and good agreement was shown between the predicted and the measured data.     

Synthesis and characterization of polycyanurate/montmorillonite nanocomposites

The advantages of cyanate esters (CEs) versus competitor systems such as epoxies and polyimides, as well as the great reinforcing potential of organoclays properly dispersed into a polymeric matrix, have been examined in a series of polycyanurate (PCN)/montmorillonite (MMT) nanocomposites prepared under appropriate polymerization conditions. The curing schedule applied resulted in gradual propagation of polymerization. Through this procedure, the intragallery curing rate becomes comparable to the extragallery one, allowing intercalation before gelation. Systems with clay loadings from 1 to 3% per weight were synthesized, and their morphology and mechanical properties were studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM), wide angle X‐ray scattering (WAXS), dynamic mechanical analysis (DMA), and tensile tests. Microscopy investigations revealed better dispersion for the 3 wt % system compared to smaller concentrations, in which aggregation and, in some cases, agglomeration were the conspicuous features. Roughness and area analyses revealed more homogeneous dispersion for this nanocomposite. Topology and 3D‐phase images further suggested considerable reduction of the average particle diameters. WAXS analysis showed that the interlayer spacing of nanocomposites was increased compared to pristine MMT, indicating the formation of intercalated structures. On the other hand, tensile strength and elongation at break values displayed abrupt diminution with MMT addition, while Young's modulus exhibited a slight but systematic increment with MMT content. The decreasing glass transition tendency observed for small clay loadings was reversed in the case of 3 wt %, while secondary transitions were practically unaffected by the presence of MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1036–1049, 2008     

Relationship between the polymer/silica interaction and properties of silica composite materials

Cast film composites have been prepared from aqueous polymer solutions containing nanometric silica particles. The polymers were polyvinyl alcohol (PVA), hydroxypropylmethylcellulose (HPMC) and a blend of PVA‐HPMC polymers. In the aqueous dispersions, the polymer–silica interactions were studied through adsorption isotherms. These experiments indicated that HPMC has a high affinity for silica surfaces, and can adsorb at high coverage; conversely, low affinity and low coverage were found in the case of PVA. In the films, the organization of silica particles was investigated through transmission electron microscopy (TEM) and small‐angle neutron scattering (SANS). Both methods showed that the silica particles were well‐dispersed in the HPMC films and aggregated in the PVA films. The mechanical properties of the composite films were evaluated using tensile strength measurements. Both polymers were solid materials, with a high‐elastic modulus (65 MPa for HPMC and 291 for PVA) and a low‐maximum elongation at break (0.15 mm for HPMC and 4.12 mm for PVA). In HPMC films, the presence of silica particles led to an increase in the modulus and a decrease in the stress at break. In PVA films, the modulus decreased but the stress at break increased upon adding silica. Accordingly, the polymer/silica interaction can be used to tune the mechanical properties of such composite films. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1134–1146, 2006     

Thermomechanical properties and crystallization behavior of layered double hydroxide/poly(ethylene terephthalate) nanocomposites prepared by in‐situ polymerization

Thermomechanical properties and crystallization behavior of poly(ethylene terephthalate) (PET) nanocomposites containing layered double hydroxide (LDH) were investigated. To enhance the compatibility between PET matrix and LDH, dimethyl 5‐sulfoisophthalate (DMSI) anion intercalated LDH (LDH‐DMSI) was synthesized by coprecipitation method, and its structure was confirmed by Fourier transform infrared (FTIR) spectrometer and X‐ray diffraction (XRD) measurements. Then, PET nanocomposites with LDH‐DMSI content of 0, 0.5, 1.0, and 2.0 wt% were prepared by in‐situ polymerization. The dispersion morphologies were observed by transmission electron microscopy (TEM) and XRD, showing that LDH‐DMSI was exfoliated in PET matrix. Thermal and mechanical properties, such as thermal stability, tensile modulus, and tensile yield strength of nanocomposites, were enhanced by exfoliated LDH‐DMSI nanolayers. However, elongation at break was drastically decreased with LDH loading owing to the increased stiffness and microvoids. The effect of exfoliated nanolayers, which acted as a nucleating agent confirmed by differential scanning calorimeter (DSC), on the microstructural parameters during isothermal crystallization, was analyzed by synchrotron small‐angle X‐ray scattering (SAXS). It is believed that nanocomposites could be crystallized more easily owing to the increased nucleation sites, which lead to the decrease of average amorphous region size and the long period with the increase of LDH‐DMSI content. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 28–40, 2007     

Mechanical,thermal and morphological properties of poly(ε‐caprolactone)/zein blends

Blends of poly(ε‐caprolactone) (PCL) with zein (PCL/zein) in different proportions (100/0, 75/25, 50/50, 25/75 and 0/100 wt% containing 5 wt% glycerol) were compared based on their mechanical properties (tensile strength, elongation at break, and Young's modulus), and on their thermal properties, the latter determined by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The morphology of the materials was studied by scanning electron microscopy (SEM). Blends of PCL/zein showed reduced tensile strength and elongation at break, but increased Young's modulus compared to the pure polymers, in agreement with the DMTA and SEM results. These findings indicated that PCL and zein were incompatible. TGA showed that the thermal stability was enhanced by the addition of zein to PCL, whereas SEM showed a poor interfacial interaction between the polymers. Copyright © 2004 John Wiley & Sons, Ltd.     

Effects of Modified MMT on Mechanical Properties of EVA/MMT Nanocomposites and Their Foams

In this study, nanocomposites of poly(ethylene-co-vinyl acetate) with two kinds of organically modified montmorillonite (OMMT) were prepared by melt intercalation. Their structures and mechanical properties were characterized by X-ray diffraction (XRD) and tensile test respectively. Especially, foaming of these nanocomposites mixed with chemical blowing agent was carried out through compression molding. Influences of OMMT on foaming ratio and mechanical properties were investigated by density test, tensile test and tear test. Results revealed that both kinds of OMMT with proper content increased tensile strength and Young's modulus of nanocomposites without a compromise of elongation at break. For foaming, OMMTs apparently improved foaming ratio and in particular, one of them can improve tear strength, tensile strength, Young's modulus and elongation although the density was decreased.     

Alteration of Bacterial Cellulose Properties by Diacetylglycerol

Bacterial cellulose (BC) was altered by means of 0.5-2.5% w/v diacetylglycerol in acetone-water through impregnation process provided DGBC composites. Results from the scanning electron microscope images, revealed that diacetylglycerol filled the pores of BC, leads to the significant enhanced in hydrophilicity and caused a smoother BC morphology. The addition of diacetylglycerol into BC caused a slightly changed in crystallinity indexes and bring about the reduction in tensile strength and Young's modulus but increased in elongation at break and toughness. The significant reduction of tensile strength and Young's modulus was achieved for DGBC 2.5% as well as for elongation at break and hydrophylicity improvement. Through the impregnation method, diacetylglycerol serves as biodegrada–ble and safe plasticizer, resulted in less rigid and higher ductility DGBC composites.     

Novel michael addition networks containing urethane hydrogen bonding

Covalently crosslinked networks based on poly(propylene glycol) bis(acetoacetate) with either neopentyl glycol diacrylate or hydroxyethyl acrylate derivatized bis(4‐isocyanatocyclohexyl)methane (HMDI) were prepared utilizing the Michael addition reaction in the presence of catalytic quantities of diazabicyclo[5.4.0]undec‐7‐ene (DBU). These networks were prepared in the absence of solvent at 23 °C without the formation of byproducts. Mechanical and thermal analyses of the networks were performed utilizing DMA, tensile testing, and TGA. Tensile analysis revealed that the introduction of hydrogen‐bonding urethane linkages in the diacrylate segment resulted in higher tensile strengths and elongation to break compared with nonhydrogen‐bonding analogs. All crosslinked products exhibited high gel fractions and excellent thermomechanical properties. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4118–4128, 2007     

Tensile properties of ligno-cellulosic fabrics coated with styrenated polyester resin

Ligno-cellulosic fabrics from the tree Hildegardia populifolia were coated with styrenated polyester resin, and their tensile strength, elastic modulus, and the percent elongation at break were determined. The effects of sodium hydroxide and a silane-coupling agent on the tensile properties of the fabric were also studied. It was observed that the tensile strength and the modulus decreased whereas the percent elongation at break increased with coating. The coupling agent improved the properties of the untreated and polyester-coated fabric, but a reverse trend was observed when the fabric was treated with sodium hydroxide. The possible reasons for this behavior are discussed.     

On the relevance of the 8‐chain model and the full‐network model for the deformation and failure of networks formed through photopolymerization of multifunctional monomers

Crosslinked networks were synthesized by copolymerization of mono‐functional tert‐butyl acrylate (tBA) with diethyleneglycol dimethacrylate (DEGDMA) or polyethylene glycol dimethacrylates (PEGDMA). By varying the chain length and concentration of the difunctional PEGDMA, we obtained tBA‐PEGDMA copolymer networks while by varying the concentration of difunctional DEGDMA, we obtained tBA‐DEGDMA crosslinked networks. The various materials were submitted to large deformations through uniaxial tension tests. For moderate weight percent of crosslinking agent, up to 20%, the networks showed standard S‐shape stress–strain curves, characteristic of rubber‐like elasticity. Two macromolecular models, the 8‐chain model and the full‐network model, were applied to fit the uniaxial tensile response of the materials. Both models provide good representations of the overall uniaxial stress–strain response of each material. After fitting to stress–strain data, the network models were employed to predict the shear modulus and the elongation at break. Neither the 8‐chain nor the full network model were capable of predicting the failure strain or shear modulus, indicating these models are best used to describe stress–strain relations rather than predict mechanical properties for the network polymers considered here. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1226–1234, 2008     

Synthesis and characterization of poly(arylene ether sulfone)s with trans‐1,4‐cyclohexylene ring containing ester linkages

trans‐1,4‐Cyclohexylene ring containing acid chloride monomers were incorporated into poly(arylene ether sulfone) (PAES) backbones to study their effect on mechanical and thermal properties. The trans‐1,4‐cyclohexylene ring containing acid chloride monomers were synthesized and characterized by NMR and high‐resolution mass spectrum. trans‐1,4‐Cyclohexylene containing PAESs were synthesized from the acid chloride monomers and hydroxyl terminated polysulfone oligomers with a pseudo‐interfacial method and a solution method. These PAESs, with trans‐1,4‐cyclohexylene ring containing ester linkages, were fully characterized by NMR, thermogravimetric analysis, differential scanning calorimetry (DSC), size exclusion chromatography, and dynamic mechanical analysis (DMA). The tensile properties were also evaluated. The polymers made with the pseudo‐interfacial method had relatively low molecular weights when compared to the solution method where much higher molecular weight polymers were obtained. Crystallinity was promoted in the low molecular weight biphenol‐based PAES samples with the pseudo‐interfacial method. The crystallinity was confirmed by both the DSC and the wide angle X‐ray diffraction results. The tensile test results of the high molecular weight polymers suggested that incorporation of the trans‐1,4‐cyclohexylene ring containing linkage slightly improved the ultimate elongations while maintaining the Young's moduli. The trans‐1,4‐cyclohexylene ring containing PAESs also showed higher sub‐T_g relaxations in DMA when compared with their terephthaloyl containing analog. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Tensile deformation of electrospun nylon‐6,6 nanofibers

Nylon‐6,6 nanofibers were electrospun at an elongation rate of the order of 1000 s^?1 and a cross‐sectional area reduction of the order of 0.33 × 10⁵. The influence of these process peculiarities on the intrinsic structure and mechanical properties of the electrospun nanofibers is studied in the present work. Individual electrospun nanofibers with an average diameter of 550 nm were collected at take‐up velocities of 5 and 20 m/s and subsequently tested to assess their overall stress–strain characteristics; the testing included an evaluation of Young's modulus and the nanofibers' mechanical strength. The results for the as‐spun nanofibers were compared to the stress–strain characteristics of the melt‐extruded microfibers, which underwent postprocessing. For the nanofibers that were collected at 5 m/s the average elongation‐at‐break was 66%, the mechanical strength was 110 MPa, and Young's modulus was 453 MPa, for take‐up velocity of 20 m/s—61%, 150 and 950 MPa, respectively. The nanofibers displayed α‐crystalline phase (with triclinic cell structure). © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1482–1489, 2006     

Hydrophilic–hydrophobic AB diblock copolymers containing poly(trimethylene carbonate) and poly(ethylene oxide) blocks

AB‐type block copolymers with poly(trimethylene carbonate) [poly(TMC); A] and poly(ethylene oxide) [PEO; B; number‐average molecular weight (M_n) = 5000] blocks [poly(TMC)‐b‐PEO] were synthesized via the ring‐opening polymerization of trimethylene carbonate (TMC) in the presence of monohydroxy PEO with stannous octoate as a catalyst. M_n of the resulting copolymers increased with increasing TMC content in the feed at a constant molar ratio of the monomer to the catalyst (monomer/catalyst = 125). The thermal properties of the AB diblock copolymers were investigated with differential scanning calorimetry. The melting temperature of the PEO blocks was lower than that of the homopolymer, and the crystallinity of the PEO block decreased as the length of the poly(TMC) blocks increased. The glass‐transition temperature of the poly(TMC) blocks was dependent on the diblock copolymer composition upon first heating. The static contact angle decreased sharply with increasing PEO content in the diblock copolymers. Compared with poly(TMC), poly(TMC)‐b‐PEO had a higher Young's modulus and lower elongation at break. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4819–4827, 2005     

Mechanical properties of gradient copolymers of styrene and n‐butyl acrylate

The mechanical properties of linear and V‐shaped compositional gradient copolymer of styrene and n‐butyl acrylate with composition of around 55 wt % styrene were investigated by comparing with their block copolymer counterparts. Compared with their block copolymer counterparts, the gradient copolymers showed lower elastic modulus, much larger elongation at break, and similar ultimate tensile strength at room temperature. This performance could be ascribed to that the local moduli continuously change from the hardest nanodomains to the softest nanodomains in the gradient copolymer, which alleviates the stress concentration during tensile test. Compared with the V‐shaped gradient (VG) copolymer, the linear gradient copolymer showed much higher elastic modulus but lower elongation at break. The mechanical properties of the gradient copolymers were more sensitive to the change in temperature from 9 °C to 75 °C. With recovery temperature increased from 10 °C to 60 °C, the strain recovery of VG copolymer would change steadily from 40% to 99%. However, the elastic recovery of linear and triblock copolymer was poor even at 60 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 860–868     

Bio-Based Nanocomposites of Cellulose Acetate and Nano-Clay with Superior Mechanical Properties

Summary: Bio-based nanocomposites were manufactured by melt intercalation of nanoclays and cellulose acetate (CA) with and without plasticizer. Glycerol triacetate (triacetin) as plasticizer up to 30 mass%, and different types of organo-modified and unmodified montmorillonites (MMTs) as filler were used. X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM), were used to study clay dispersion, intercalation/exfoliation, and structure of the composites. XRD and TEM revealed very good dispersion and exfoliation of modified clay throughout the CA matrix. While for unmodified clay agglomeration and poor dispersion but an intercalated structure was observed. The mechanical properties of injection moulded test bars were determined by a tensile experiment giving tensile strength, Young's modulus and elongation at break. Adding plasticizer facilitated the processing and up to 20 mass%, increased the tensile strength, Young's modulus and elongation at break as well. Higher amount of plasticizer diminished the tensile properties except elongation showing a slight increase. In all plasticized composites, organo-modified clay improved the tensile strength and at the same time, young's modulus and elongation almost remained constant. On the other hand, plasticized CA compounded with unmodified clay revealed lower properties. In a particular case, compounding of unplasticized CA with unmodified clay resulted in superior mechanical properties with a novel structure. So that, in optimum percentage –5 mass%- of unmodified clay, tensile strength and young's modulus increased significantly by 335% and 100%, to 178 MPa and 8.4 GPa, respectively. This is a dramatic improvement in strength and stiffness of CA. Adding organo-modified clay resulted in a little improvement in tensile properties. SEM pictures of the optimum composite showed a core/shell structure with high orientation in the shell part. It is supposed that this behaviour is caused by the interaction between CA hydroxyl groups and free cations existing in the galleries of unmodified clay.     

Synthesis and characterization of new soluble cardo polyamide‐imides containing cyclododecyl groups

A new cardo diimide‐dicarboxylic acid, 1,1‐bis[4‐(4‐trimellitimidophenoxy)phenyl]cyclododecane (BTPCD), containing a pendant cyclododecyl group was synthesized by the condensation reaction of 1,1‐bis[4‐(4‐aminophenoxy)phenyl]cyclododecane with trimellitic anhydride in glacial acetic acid. A series of new cardo polyamide‐imides were prepared by the direct polycondensation of BTPCD and various aromatic diamines in N‐methyl‐2‐pyrrolidinone (NMP) with triphenyl phosphite and pyridine as condensing agents. The polymers were produced in high yields and with moderate‐to‐high inherent viscosities of 0.72–1.02 dL g⁻¹. The number‐average and weight‐average molecular weights of the polymers ranged from 21,000 to 49,000 and 58,000 to 92,000, respectively. All the polymers exhibited excellent solubility and could be readily dissolved in various solvents such as NMP, N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethyl sulfoxide, pyridine, cyclohexanone, and tetrahydrofuran. These polyamide‐imides had glass‐transition temperatures between 241 and 262 °C and 10% weight‐loss temperatures ranging from 469 to 511 °C in nitrogen. The polymer films had a tensile strength range of 79–108 MPa, an elongation at break range of 7–14%, and a tensile modulus range of 2.0–2.4 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2787–2793, 2000     

Block copolymer materials from the organocatalytic ring‐opening polymerization of a pentaerythritol‐derived cyclic carbonate

9‐Phenyl‐2,4,8,10‐tetraoxaspiro[5,5]undecanone (PTO) was synthesized from pentaerythritol via the acid‐catalyzed acetal formation reaction with benzaldehyde and subsequent ring closure with ethyl chloroformate. The cyclic carbonate monomer was subsequently polymerized by ring‐opening polymerization (ROP) initiated from 1,4‐butanediol (1,4‐BDO) using the 1‐(3,5‐bis(trifluoromethyl)phenyl)‐3‐cyclohexylthiourea and 1,8‐diazabicyclo[5.4.0]undec‐7‐ene dual organocatalytic system. It was found that the organocatalyst allowed for the synthesis of well‐defined polymers with minimal adverse side reactions and low dispersities. This system was then employed in the ROP of PTO initiated from an α,ω‐dihydroxy poly(caprolactone) (PCL) macroinitiator, with varying molecular weights, to yield a series of A‐B‐A block copolymers. These materials were characterized by ¹H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis and tensile analysis. It was found that the chain extension from PCL with poly(PTO) (PPTO) blocks yielded a thermoplastic material with superior tensile properties (elongation and Young's modulus) to that of the PCL homopolymer. Furthermore, it was noted that the addition of PPTO could be employed to alter the crystallization properties (crystallization temperature (T_c), and percentage crystallization) of the central PCL block. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2279–2286