Chemical modification of butyl rubber. II. Structure and properties of poly(ethylene oxide)-grafted butyl rubber

Poly(ethylene oxide)-grafted butyl rubbers (IIR-g-PEOs), which were synthesized from potassium salt of polyethylene glycol monomethyl ether (PEGM) and chlorinated butyl rubber, were found to behave like thermoplastic elastomers. The poly(ethylene oxide) (PEO) content of these amphiphilic polymers was ca. 10 wt %, and their PEO lengths were 750, 2000, and 5000, respectively. The grafted segments of PEO in butyl rubber (IIR) aggregated to form the PEO domains in IIR matrix. At constant PEO content, the longer the PEO segment length, the larger the size and the crystallinity of PEO domains became. This PEO domain worked as a cross-linking site and a reinforcing filler. The degree of swelling in water of IIR-g-PEO film that was prepared from PEGM-5000 was largest, but its emulsification ability was smallest among them. © 1995 John Wiley & Sons, Inc.     

Chemical modification of butyl rubber. I. Synthesis and properties of poly(ethylene oxide)-grafted butyl rubber

A new amphiphilic polymer, i.e., poly(ethylene oxide) (PEO)-grafted butyl rubber (IIR-g-PEO), was synthesized by chemical modification of chlorinated butyl rubber (CIIR). This synthesis was based on the reaction between chlorine in CIIR and potassium salt of polyethylene glycol monomethyl ether (PEGM). PEGM's with molecular weights of 750 and 2000 were used. The maximum grafting percent of the resulted copolymers after the purification was ca. 45%, regardless of the molecular weight of PEGM. The microphase separated structure was observed in the films of IIR-g-PEOs. IIR-g-PEO, whose PEO molecular weight was 2000 and whose PEO content was 23.8 wt %, swelled 3.1% in water, and it was six times larger than the swelling of CIIR. The hydrophilicity of grafted polymers depended on the molecular weight of PEO side chains and PEO content. Even when the PEO contents were same in the polymers which were grafted PEGM-750 and PEGM-2000, their swellings in organic solvents were not equal. It was due to the difference of the microphase-separated structures of the grafted polymers. IIR-g-PEO, whose PEO molecular weight was 750 and whose PEO content was 10.3 wt %, swelled 1.5% in water, but showed an excellent emulsifying ability, where an oil-in-water-type emulsion was formed. © 1993 John Wiley & Sons, Inc.     

Vinyl ether end‐groups in poly(ethylene glycol)s from the Na2CO3‐promoted degradation of 1,3‐dioxolan‐2‐one polymers

The Na₂CO₃‐promoted polymerization of 1,3‐dioxolan‐2‐one (I) to afford poly(ethylene glycol) III was reinvestigated. The reaction appeared to involve a nucleophilic attack against the carbonyl and methylene groups of I to afford poly(carbonate) II with poly(ethylene glycol) linkages and ethylene oxide IV as a side product (10–22%). As the reaction progressed, poly(carbonate) II decreased and poly(ethylene glycol) III increased. Under some conditions, poly(ethylene glycol)s V and VI with vinyl ether terminal groups were formed unexpectedly. The formation of unsaturated products during the polymerization of I/EO (ethylene oxide) has not been reported in the literature. We believe that vinyl ethers were formed from the degradation of poly(carbonate)s and were accompanied by a reduction in molecular weight. The structures of vinyl ethers V and VI were confirmed by hydrogenation of the double bond into the ethyl ether group in VII and VIII, respectively. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 152–160, 2000     

Kinetic absorption of vapors of alkyl acetates C<Subscript>1</Subscript>-C<Subscript>4</Subscript> and diethyl ether on thin films of modified piezoelectric quartz resonators

Sorption of methyl acetate, ethyl acetate, propyl acetate, butyl acetate, and diethyl ether on thin films of esters: poly(ethylene glycol) sebacate and phthalate, dinonyl phthalate, tween-40, pentaerythritol tetrabenzoate, triphenyl phosphate, Triton X-305, and stearic acid was studied. The mass of sorbent films was optimized, the sensitivity and selectivity of modifiers toward analytes was evaluated, and the time of maximum sorption was determined.     

Laboratory studies of the ·OH‐initiated photooxidation of ethyl‐n‐butyl ether and di‐n‐butyl ether

Oxygenated compounds such as ethers and alcohols are used as gasoline additives and industrial solvents. However, despite their widespread use, the atmospheric reaction mechanisms of some of these compounds are unknown. This study examines the ^·OH‐initiated gas‐phase removal mechanisms of ethyl‐n‐butyl ether (ENBE) and di‐n‐butyl ether (DNBE) utilizing gas chromatography–mass spectrometry techniques. The primary products and molar yields from the hydroxyl‐radical–initiated photooxidation of ENBE in the presence of nitric oxide were acetaldehyde (0.173 ± 0.012), ethyl formate (0.219 ± 0.033), butyraldehyde (0.076 ± 0.004), butyl formate (0.241 ± 0.009), butyl acetate (0.032 ± 0.001), and ethyl butyrate (0.0044 ± 0.0006). From the calculated molar yields, approximately 45.5% of the reacted carbon were recovered. The primary products and molar yields from the DNBE and hydroxyl radical reaction in the presence of nitric oxide were propionaldehyde (0.379 ± 0.022), butyraldehyde (0.119 ± 0.003), butyl formate (0.410 ± 0.009), and butyl butyrate (0.019 ± 0.001). Approximately 47.7% of the reacted DNBE were recovered. The chemical mechanisms are presented to explain the formation of these products. In addition, the importance of the isomerization and nitrate/nitrite formation pathways in the reactions of large ethers are discussed. © 2001 John Wiley & Sons, Inc. Int J Chem Kinet 33: 328–341, 2001     

毛细管气相色谱法同时测定油漆溶剂中二甲苯和乙二醇乙醚乙酸酯

基于乙二醇乙醚乙酸酯的极性、沸点与二甲苯的几种同分异构体相近而难以分离的特性,选择合适的二甲基聚硅氧烷柱毛细管分离柱(AT.SE-30),以氮气为载气,流量为0.6 mL/m in,内标法定量,建立了同时测定油漆溶剂中二甲苯和乙二醇乙醚乙酸酯含量的毛细管气相色谱法。用该方法对油漆样品进行测定,乙二醇乙醚乙酸酯和二甲苯的回收率为96.5%~102.8%,相对标准偏差不大于2.0%。     

Temperature-responsive swelling and deswelling of the copolymers from vinyl ether of ethylene glycol and butyl vinyl ether

Linear and crosslinked copolymers of a vinyl ether of ethylene glycol (2-hydroxyethyl vinyl ether, ( 1 )) and butyl vinyl ether ( 2 ) are synthesized by α-irradiation polymerization. It is shown that the linear copolymers exhibit a phase separation phenomenon in dependence of the temperature due to the destruction of hydrogen bonds and the enhancement of hydrophobic interaction in aqueous solution. The processes of reversible swelling or shrinking upon temperature change are demonstrated for polymer networks.     

Poly(ethylene terephthalate) copolymers containing 5‐tert‐butyl isophthalic units

Poly(ethylene terephthalate‐co‐5‐tert‐butyl isophthalate) copolymers, abbreviated as PET^tBI, with compositions ranging between 95/5 and 25/75, as well as the two parent homopolymers, PET and PE^tBI, were prepared from comonomer mixtures by a two‐step melt‐polycondensation. Polymer intrinsic viscosities varied from 0.4 to 0.7 dL g^?1 with weight‐average molecular weights ranging between 31,000 and 80,000. The copolymers were found to have a random microstructure with a composition according to that used in the corresponding feed. The melting temperature and crystallinity of PET^tBI decreased with the content in 5‐tert‐butyl isophthalic units, whereas the glass‐transition temperature increased from 82 °C for PET up to 99 °C for PE^tBI. Copolymerization slightly improved the thermal stability of PET. Preliminary X‐ray diffraction studies revealed that PET^tBI adopt the same crystal structure as PET with the alkylated isophthalic units probably excluded from the crystal lattice. The homopolymer PE^tBI appeared to be a highly crystalline polymer taking up a crystal structure clearly different from that of PET and PET^tBI copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 1994–2004, 2001     

Effect of copolymer composition on interpolymer complex formation of (co)poly(vinyl ether)s with poly(acrylic acid) in aqueous and organic solutions

The complex formation between vinyl ether of poly(ethylene glycol‐co‐vinyl butyl ether) with poly(acrylic acid) has been considered in aqueous and isopropanol solutions. The effect of copolymer composition on the complex formation process was clarified. It has been shown that the incorporation of hydrophobic fragments into macromolecules enhances the hydrophobic stabilization of polycomplexes in aqueous solutions. In organic media this effect disappears. The stability of polycomplexes formed both in aqueous and in organic solutions in respect to the addition of dimethylformamide has been studied.     

Stabilization of water/n‐hexane emulsions by amphiphilic copolymers based on vinyl ethers and their polycomplexes with poly(acrylic acid)

Amphiphilic random copolymers based on vinyl ether of ethylene glycol and vinyl butyl ether as well as their polycomplexes with poly(acrylic acid) were studied as polymeric reagents for the stabilization of water/n‐hexane emulsions. The emulsion stability strongly depended on the content of vinyl butyl ether in the copolymers as well as their concentration in solution. The more hydrophobic copolymers stabilized emulsions more efficiently. An increase in the temperature and the addition of inorganic salts reduced the emulsion lifetime. The formation of interpolymer complexes between the copolymers and poly(acrylic acid) significantly influenced the stability of the emulsions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2625–2632, 2004     

Synthesis of superparamagnetic and thermoresponsive hybrid nanoparticles via surface‐mediated RAFT polymerization of di(ethylene glycol) ethyl ether acrylate and (oligoethylene glycol) methyl ether acrylate

A reversible addition‐fragmentation chain transfer (RAFT) agent was directly anchored onto superparamagnetic Fe₃O₄ nanoparticles (SPNPs) in a simple procedure using a ligand exchange reaction of 2‐[(dodecylsulfanylcarbonylthiolsulfanyl) propionic acid] (DCPA) with oleic acid initially present on the surface of Fe₃O₄ nanoparticles. The DCPA‐modified SPNPs were then used for the surface‐mediated RAFT polymerization of di(ethylene glycol) ethyl ether acrylate and (oligoethylene glycol) methyl ether acrylate to fabricate structurally well‐defined hybrid SPNPs with temperature‐responsive poly[di(ethylene glycol) ethyl ether acrylate‐co‐(oligoethylene glycol) methyl ether acrylate] shell and magnetic Fe₃O₄ core. Evidence of a well‐controlled surface‐mediated RAFT polymerization was gained from a linear increase of number‐average molecular weight with overall monomer conversions and relatively narrow polydispersity indices of the copolymers grown from the SPNPs. The resultant hybrid nanoparticles exhibited superparamagnetic property with a saturation magnetization of 55.1–19.4 emu/g and showed a temperature‐responsive phenomenon as the temperature changed between 25 and 40 ^°C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3420–3428     

Synthesis of amphiphilic copolymer brushes: Poly(ethylene oxide)‐graft‐polystyrene

A well‐defined amphiphilic copolymer brush with poly(ethylene oxide) as the main chain and polystyrene as the side chain was successfully prepared by a combination of anionic polymerization and atom transfer radical polymerization (ATRP). The glycidol was first protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether and then copolymerized with ethylene oxide by the initiation of a mixture of diphenylmethylpotassium and triethylene glycol to give the well‐defined polymer poly(ethylene oxide‐co‐2,3‐epoxypropyl‐1‐ethoxyethyl ether); the latter was hydrolyzed under acidic conditions, and then the recovered copolymer of ethylene oxide and glycidol {poly(ethylene oxide‐co‐glycidol) [poly(EO‐co‐Gly)]} with multiple pending hydroxymethyl groups was esterified with 2‐bromoisobutyryl bromide to produce the macro‐ATRP initiator [poly(EO‐co‐Gly)_(ATRP). The latter was used to initiate the polymerization of styrene to form the amphiphilic copolymer brushes. The object products and intermediates were characterized with ¹H NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, Fourier transform infrared, and size exclusion chromatography in detail. In all cases, the molecular weight distribution of the copolymer brushes was rather narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), and the linear dependence of ln[M₀]/[M] (where [M₀] is the initial monomer concentration and [M] is the monomer concentration at a certain time) on time demonstrated that the styrene polymerization was well controlled. This method has universal significance for the preparation of copolymer brushes with hydrophilic poly(ethylene oxide) as the main chain. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4361–4371, 2006     

Characterization and catalytic performance of basaltic dust as an efficient catalyst in the liquid‐phase esterification of acetic acid with n‐butanol

Three natural basaltic samples were collected and used as efficient catalysts for the liquid‐phase synthesis of n‐butyl acetate. The samples were characterized by X‐ray fluorescence analysis (XRF), X‐ray diffraction (XRD), thermogravimetry (TG), differential thermal analysis (DTA), Fourier transform infrared (FT‐IR), scanning electron microscopy (SEM), and N₂ sorption. The acidity of the samples was determined using isopropanol dehydration, and the strength of the acid sites was measured using chemisorption of basic probes. The catalytic activity of the samples towards the esterification of acetic acid with n‐butanol was extensively examined. The influence of different parameters, such as the reaction refluxing time, molar ratio, catalyst loading, reusability, and calcination temperature, on the esterification reaction was studied in detail. The results revealed that all samples had high catalytic activity with a selectivity of 100% to n‐butyl acetate formation. In addition, the sample obtained from the top hill of Volcano had the highest activity with a 80% yield of n‐butyl acetate. Moreover, the significant catalytic performances were well correlated with the acidity of the samples and to the reaction rate constants.     

乙二醇二缩水甘油醚的合成及作为阳离子型紫外光固化稀释剂性能研究

以三氟化硼乙醚络合物为催化剂,以氢氧化钠为成环反应的闭环剂,利用乙二醇和环氧氯丙烷为原料合成了乙二醇二缩水甘油醚.研究了催化剂三氟化硼乙醚络合物用量、环氧氯丙烷和乙二醇摩尔比、氢氧化钠和乙二醇摩尔比,以及成环反应温度这些因素对合成反应的影响.结果表明较好的合成反应条件是:三氟化硼乙醚络合物质量分数为0.40%,环氧氯丙烷和乙二醇较佳摩尔比为2.4:1,氢氧化钠和乙二醇较佳摩尔比为2.2:1,较佳的成环反应温度为30℃.同时,把乙二醇二缩水甘油醚作为稀释剂加入到环氧树脂E-51中,利用三芳基锍鎓六氟锑酸盐作为引发剂,制备了阳离子型紫外光固化涂料,其紫外光固化膜的拉伸强度为46.25MPa,杨氏模量为1487.26MPa,断裂伸长率为6.27%.     

Preparation of microcapsulated ammonium polyphosphate,pentaerythritol with glycidyl methacrylate,butyl methacrylate and their synergistic flame‐ retardancy for ethylene vinyl acetate copolymer

A new series of microcapsules containing pentaerythritol (PER) and ammonium polyphosphate (APP) with glycidyl methacrylate and butyl methacrylate as shell materials were synthesized by in situ polymerization. The structure and performance of the microencapsulated APP and microencapsulated PER were characterized by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, scanning electron microscopy, and water contact angle. The flame retarded ethylene‐vinyl acetate copolymer (EVA) composites were studied by limiting oxygen index, UL‐94 test, and cone calorimeter. It was found that the microencapsulation of flame retardants (FRs) with the glycidyl methacrylate and butyl methacrylate lead to a decrease in the particle's water solubility and an improvement of the hydrophobicity. Results also demonstrated that the FR properties of EVA/microencapsulated APP/microencapsulated PER composites were better than those of the EVA/APP/PER composites at the same loading of FRs. The thermogravimetric analysis results reflected that the microencapsulated EVA composites had better thermal stability because of the forming of stable char during the combustion. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis of peroxide‐curable butyl rubber via suzuki–miyaura coupling of halogenated butyl rubber with 4‐vinylphenylboronic acid

The Suzuki–Miyaura coupling reaction of brominated butyl rubber (BIIR) and/or chlorinated butyl rubber with a mixture of 4‐vinylphenylboronic acid and phenylboronic acid was carried out in THF under various conditions using a di‐μ‐chlorobis [5‐hydroxy‐2‐[1‐(hydroxyimino‐κN)ethyl]phenylκC] palladium(II) dimer, which is a type of cyclopalladated complex, as a catalyst. When BIIR and a small amount (Pd/Br ≈ 1/1000) of complex were used as the substrate and catalyst, respectively, a 4‐vinylphenyl and phenyl group could be introduced to butyl rubber in a high yield. Isomerization of the exo carbon–carbon double bond in BIIR was observed during the coupling reaction to give a cis and trans endo structure. The peroxide curing behavior of the resulting polymer at 170 °C indicated that the polymer could be cured by dicumyl peroxide, and the maximum torque of the resulting material, which reflects the crosslink density, was controllable by the composition of the boronic acids used. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparative enantioseparation of propafenone by counter‐current chromatography using di‐n‐butyl l‐tartrate combined with boric acid as the chiral selector

This paper extends the research of the utilization of borate coordination complexes in chiral separation by counter‐current chromatography (CCC). Racemic propafenone was successfully enantioseparated by CCC with di‐n‐butyl l ‐tartrate combined with boric acid as the chiral selector. The two‐phase solvent system was composed of chloroform/ 0.05 mol/L acetate buffer pH 3.4 containing 0.10 mol/L boric acid (1:1, v/v), in which 0.10 mol/L di‐n‐butyl l ‐tartrate was added in the organic phase. The influence of factors in the enantioseparation of propafenone were investigated and optimized. A total of 92 mg of racemic propafenone was completely enantioseparated using high‐speed CCC in a single run, yielding 40–42 mg of (R)‐ and (S)‐propafenone enantiomers with an HPLC purity over 90–95%. The recovery for propafenone enantiomers from fractions of CCC was in the range of 85–90%.     

Simultaneous measurement of methyl tert‐butyl ether and tert‐butyl alcohol in human serum by headspace solid‐phase microextraction gas chromatography–mass spectrometry

The abundant production of methyl tert‐butyl ether (MTBE) and its widespread use have led to an increase in the potential for human exposure. This work described a simple, fast, sensitive, reliable and low‐cost method for the simultaneous measurement of MTBE and its metabolite, tert‐butyl alcohol (TBA) in human serum by headspace solid‐phase microextraction gas chromatography–mass spectrometry. Extraction conditions were optimized and 40 °C, 10 min, 250 rpm and 0.3 g NaCl for a 1 mL sample were the optimal conditions. This method showed good analytical performance in terms of sensitivity with limits of detection in serum (1 mL) of 0.03 µg/L for MTBE and 0.05 µg/L for TBA, accuracy (mean recovery values) from 75.8% to 85.8%, precision (relative standard deviations) <10% and sample stability (biodegradation) <10% after 28 days. A verification experiment proved the reproducibility and stability of this method as well. Finally the method was used to detect 212 specimens, and the internal dose levels for MTBE in human serum were presented in China. Copyright © 2015 John Wiley & Sons, Ltd.     

A library of thermoresponsive PEG-based methacrylate homopolymers: How do the molar mass and number of ethylene glycol groups affect the cloud point?

In this study, a novel library of thermoresponsive homopolymers based on poly (ethylene glycol) (EG) (m)ethyl ether methacrylate monomers is presented. Twenty-seven EG based homopolymers were synthesized and three parameters, the molar mass (MM), the number of the ethylene glycol groups in the monomer, and the chemistry of the functional side group were varied to investigate how these affect their thermoresponsive behavior. The targeted MMs of these polymers are varied from 2560, 5000, 8200 to 12,000 g mol⁻¹. Seven PEG-based monomers were investigated: ethylene glycol methyl ether methacrylate (MEGMA), ethylene glycol ethyl ether methacrylate (EEGMA), di(ethylene glycol) methyl ether methacrylate (DEGMA), tri(ethylene glycol) methyl ether methacrylate (TEGMA), tri(ethylene glycol) ethyl ether methacrylate (TEGEMA), penta(ethylene glycol) methyl ether methacrylate (PEGMA), nona(ethylene glycol) methyl ether methacrylate (NEGMA). Homopolymers of 2-(dimethylamino) ethyl methacrylate (DMAEMA) were also synthesized for comparison. The cloud points of these homopolymers were tested in different solvents and it was observed that it decreases as the number of EG group was decreased or the MM increased. Interestingly, the end functional group (methoxy or ethoxy) of the side group has an effect as well and is even more dominant than the number of EG groups.     

A3‐type star polymers via click chemistry

We report a simple preparation of three‐armed (A₃‐type) star polymers based on the arm‐first technique, using a click‐reaction strategy between a well‐defined azide‐end‐functionalized polystyrene, poly(tert‐butyl acrylate), or poly(ethylene glycol) precursor and a trisalkyne‐functional initiator, 1,1,1‐tris[4‐(2‐propynyloxy)phenyl]ethane. The click‐reaction efficiency for A₃‐type star formation has been investigated with gel permeation chromatography measurements (refractive‐index detector). The gel permeation chromatography curves have been split with the deconvolution method (Gaussian area), and the efficiency of A₃‐type star formation has been found to be 87%. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6458–6465, 2006