Decontamination of the chemical warfare agent simulant dimethyl methylphosphonate by means of large-area low-temperature atmospheric pressure plasma

Dimethyl methylphosphonate (DMMP), a chemical simulant of the nerve gas GB, was decontaminated with a nonthermal atmospheric pressure plasma. The decontamination efficiency was measured qualitatively by means of Fourier transform spectroscopy and quantitatively by means of gas chromatography. With helium gas only, 10 g/m² of DMMP on an aluminum surface was 99.9% decontaminated in 2 min, furthermore, with the addition of 5% of oxygen gas, it was 99.99% decontaminated in 10 min. Given the low input power (<100 W) and temperature (<75 °C), this plasma is eligible for nondestructive decontamination of almost all material surfaces.     

Low temperature argon plasma sterilization effect on Pseudomonas aeruginosa and its mechanisms

In the present work, low temperature argon plasma was used to sterilize Pseudomonas aeruginosa on PET sheets. The discharge conditions were as follows: power of 30 W and gas flux of 20 cm³/min, and the pressure in the reaction chamber was 6.2 Pa. In a self-designed plasma reaction equipment, active species (electron, ion, radical and UV light, etc.) were separated effectively, and the discharge zone, afterglow zone and remote zone were plotted out in the plasma field. For a treatment time of 60 s, the germicidal effects were 3.94, 3.86 and 2.93 respectively in the three zones. The results show that argon plasma can effectively sterilize P. aeruginosa in a short time. Before and after plasma treatment, cell morphology was studied via scanning electron microscopy (SEM). Cell wall or cell membrane cracking was tested to determine the content of nucleic acid in the bacteria suspensions using ultraviolet spectroscopy. To test the content of protein, a coomassie light blue technique was used. The results show that plasma activity cracks the cell wall and cell membrane, resulting in cellular content leakage. In addition, the results from electron spin resonance (ESR) spectroscopy and double Langmuir electron probe show that electrons, ions and argon free radicals play important roles in sterilization in the discharge zone, but only argon free radicals act to sterilize bacteria in the afterglow zone and the remote zone.     

Sonophotocatalytic inactivation of E. coli using ZnO nanofluids and its mechanism

The present study evaluated inactivation efficiency of a sonophotocatalytic process using ZnO nanofluids including ultrasonic parameters such as power density, frequency and time. The result showed that inactivation efficiency was increased by 20% when ultrasonic irradiation was combined with photocatalytic process in the presence of natural light. Comparison of inactivation efficiency in photocatalytic, ultrasonic and sonocatalytic processes using Escherichia coli as a model bacteria identified that inactivation efficiencies are shown in the following order: ultrasonic irradiation < sonocatalysis < photocatalysis < sonophotocatalysis. Furthermore, inactivation mechanism of sonophotocatalysis was proposed. Studies of reactive oxygen species (ROS) and zinc ions (Zn²⁺) release evaluation revealed that ROS play a key role in bacterial inactivation rather than Zn²⁺. Permeability of outer membrane (OM) and inner membrane (IM) of E. coli bacterial cells were studied and exhibited that sonophotocatalysis increased the permeability of OM and IM significantly. The enhanced bacterial inactivation effect in sonophotocatalytic process contributed to acoustic cavitation, sonocatalysis of ZnO and sonoporation phenomenon.     

Analysis of sterilization effect by pulsed dielectric barrier discharge

Atmospheric pressure (AP) plasmas can sterilize against almost all kinds of bacteria because many ions and reactive species, such as oxygen atoms and ozone, etc., are generated during AP plasmas. So AP plasmas are proper processes for application to air cleaners and sterilizers. The aim of this paper is to evaluate a germicidal effect caused by pulsed plasma system in air utilizing a dielectric barrier discharge (DBD) type reactor incorporating alumina, glass, etc. Escherichia coli, Bacillus subtilis and Pseudomonas aeruginosa bacteria were used for this sterilization experiment. For analysis of the relationship between sterilization results and chemical species generated in the discharge, we used optical emission spectroscopy and we checked emission spectra by atomic oxygen (394.2 and 436.8 nm) and second positive system of nitrogen (337.1 nm). Experimental results showed that DBD treatment during 70 s sterilized E. coli with 99.99% effectively and ozone molecules were the dominant germicidal species. From these results we concluded that the pulsed DBD system is very effective for sterilization.     

The inactivation kinetics of polyphenol oxidase in mushroom (Agaricus bisporus) during thermal and thermosonic treatments

The effect of thermal and thermosonic treatments on the inactivation kinetics of polyphenol oxidase (PPO) in mushroom (Agaricus bisporus) was studied in 55–75 °C temperature range. In both the processes, the inactivation kinetics of PPO followed a first-order kinetics (R² = 0.941–0.989). The D values during thermal inactivation varied from 112 ± 8.4 min to 1.2 ± 0.07 min while they varied from 57.8 ± 6.1 min to 0.88 ± 0.05 min during thermosonic inactivation at the same temperature range. The activation energy during thermal inactivation was found to be 214 ± 17 kJ/mol, while it was 183 ± 32 kJ/mol during thermosonic inactivation. The inactivating effect of combined ultrasound and heat was found to synergistically enhance the inactivation kinetics of PPO. The D values of PPO decreased by 1.3–3 times during thermosonic inactivation compared to the D values of PPO during thermal inactivation at the temperature range. Therefore, thermosonication can be further developed as an alternative to “hot break” process of mushroom.     

Acetaldehyde photochemistry on TiO2(1 1 0)

The ultraviolet (UV) photon induced decomposition of acetaldehyde adsorbed on the oxidized rutile TiO₂(1 1 0) surface was studied with photon stimulated desorption (PSD) and thermal programmed desorption (TPD). Acetaldehyde desorbs molecularly from TiO₂(1 1 0) with minor decomposition channels yielding butene on the reduced TiO₂ surface and acetate on the oxidized TiO₂ surface. Acetaldehyde adsorbed on oxidized TiO₂(1 1 0) undergoes a facile thermal reaction to form a photoactive acetaldehyde–oxygen complex. UV irradiation of the acetaldehyde–oxygen complex initiated photofragmentation of the complex resulting in the ejection of methyl radical into gas phase and conversion of the surface bound fragment to formate.     

A collisional cooling investigation of the pressure broadening of the 110←101 transition of water from 17 to 200 K

An investigation of the 1₁₀←1₀₁ rotational transition of water at 556 GHz pressure broadened by hydrogen, helium, nitrogen, oxygen and carbon dioxide has been completed. Using the collisional cooling technique the broadening of this transition by each gas was explored from 200 K down to the condensation point of the broadening gas or 17 K, which ever is lower. This marks the first time such an extensive investigation of the broadening of this rotational transition as a function of temperature has been completed. The results of this investigation will be presented including the exponential temperature dependence of the broadening, the lack of temperature dependence of the broadening observed in helium and the unique behavior of the hydrogen broadening at low temperature (<40 K). In addition, the broadening of the 1₁₀←1₀₁ rotational transition of water by nitrogen and oxygen was recorded at room temperature and a direct comparison of this data with recent work will be discussed.     

Synergetic effects of ultrasound and slightly acidic electrolyzed water against Staphylococcus aureus evaluated by flow cytometry and electron microscopy

This study evaluated the synergetic effects of ultrasound and slightly acidic electrolyzed water (SAEW) on the inactivation of Staphylococcus aureus using flow cytometry and electron microscopy. The individual ultrasound treatment for 10 min only resulted in 0.36 log CFU/mL reductions of S. aureus, while the SAEW treatment alone for 10 min resulted in 3.06 log CFU/mL reductions. The log reductions caused by combined treatment were enhanced to 3.68 log CFU/mL, which were greater than the sum of individual treatments. This phenomenon was referred to as synergistic effects. FCM analysis distinguished live and dead cells as well as revealed dynamic changes in the physiological states of S. aureus after different treatments. The combined treatment greatly reduced the number of viable but nonculturable (VBNC) bacteria to 0.07%; in contrast, a single ultrasound treatment for 10 min induced the formation of VBNC cells to 45.75%. Scanning and transmission electron microscopy analysis revealed that greater damage to the appearance and ultrastructure of S. aureus were achieved after combined ultrasound-SAEW treatment compared to either treatment alone. These results indicated that combining ultrasound with SAEW is a promising sterilization technology with potential uses for environmental remediation and food preservation.     

Electrical conductivity and oxygen permeation properties of SrCoFeOx membranes

The total conductivity and oxygen permeation properties of dense SrCoFeO_x membranes synthesized from the solid state method were studied in the temperature range of 700–900 °C. The SrCoFeO_x membranes consist of an intergrowth (Sr₄Fe_6 − xCo_xO_13 ± δ), perovskite (SrFe_1 − xCo_xO_3 − δ), and spinel (Co_3 − xFe_xO₄) phase. SrCoFeO_x exhibits n-type and p-type conduction at low and high oxygen partial pressures, respectively, and has a total conductivity of 16.5 S/cm at 900 °C in air. The oxygen permeation fluxes for SrCoFeO_x and SrFeCo_0.5O_x membranes were measured with either an inert or carbon monoxide sweep gas. The oxygen permeation fluxes were higher through SrCoFeO_x membranes than SrFeCo_0.5O_x membranes and can be attributed to a difference in the amount and makeup of the perovskite phase present in each composition. The oxygen permeation fluxes with a carbon monoxide sweep gas were approximately two orders of magnitude larger than the fluxes measured with an inert sweep gas for both compositions. The large oxygen permeation fluxes observed with a carbon monoxide sweep are due to a higher driving force for oxygen transport and a reaction on the sweep side of the membrane that maintains a low oxygen partial pressure.     

Multi-species time-history measurements during n-hexadecane oxidation behind reflected shock waves

Species concentration time-histories were measured during oxidation for the large, normal-alkane, diesel-surrogate component n-hexadecane. Measurements were performed behind reflected shock waves in an aerosol shock tube, which allowed for high fuel loading without pre-test heating and possible decomposition and oxidation. Experiments were conducted using near-stoichiometric mixtures of n-hexadecane and 4% oxygen in argon at temperatures of 1165–1352 K and pressures near 2 atm. Concentration time-histories were recorded for five species: C₂H₄, CH₄, OH, CO₂, and H₂O. Methane was monitored using DFG laser absorption near 3.4 μm; OH was monitored using UV laser absorption at 306.5 nm; C₂H₄ was monitored using a CO₂ gas laser at 10.5 μm; and CO₂ and H₂O were monitored using tunable DFB diode laser absorption at 2.7 and 2.5 μm, respectively. These time-histories provide critically needed kinetic targets to test and refine large reaction mechanisms. Comparisons were made with the predictions of two diesel-surrogate reaction mechanisms (Westbrook et al. [1]; Ranzi et al. [9]) that include n-hexadecane, and areas of needed improvement in the mechanisms were identified. Comparisons of the intermediate product yields of ethylene for n-hexadecane with those found for other smaller n-alkanes, show that an n-hexadecane mechanism derived from a simple hierarchical extrapolation from a smaller n-alkane mechanism does not properly simulate the experimental measurements.     

Mixed oxygen ion and electron conducting hollow fiber membranes for oxygen separation

Phase inversion spinning technique was employed to prepare dense perovskite hollow fiber membranes made from composition BaCo_xFe_yZr_zO_3−δ (BCFZ, x + y + z = 1.0). Scanning electron microscope (SEM) shows that such hollow fibers have an asymmetric structure, which is favored to the oxygen permeation. An oxygen permeation flux of 7.6 cm³/min cm² at 900 °C under an oxygen gradient of 0.209 × 10⁵ Pa/0.065 × 10⁵ Pa was achieved. From the Wagner Theory, the oxygen permeation through the hollow fiber membrane is controlled by both bulk diffusion and surface exchange. The elements composition of fresh fiber and the fiber after long-term experiments were analyzed by energy-dispersive X-ray spectra (EDXS). Compared to the fresh fiber, sulphur was found on the tested hollow fiber membrane surface exposed to the air side and in the bulk, and Ba segregations occur on the tested hollow fiber membrane surface exposed to the air side. A decrease of the oxygen permeation flux was observed, which was probably due to the sulphur poisoning.     

Strong violet emission from zinc oxide dumbbell-like microrods and nanowires

ZnO of different morphologies with controlled size and aspect ratio (l/d) such as dumbbell-like microrods, thick nanowires and thin nanowires were prepared by a hydrothermal method. Possible mechanisms for the formation of ZnO crystals with the different morphologies were discussed. Strong violet photoluminescence bands at～413 nm (3.0 eV) without band edge emission were observed from the dumbbell-like ZnO microrods and thick nanowires. Correspondingly, the thin nanowires showed a weak shoulder UV photoluminescence band at～390 nm. Such result indicates that the photoluminescence properties could be improved by the morphologies or aspect ratio (l/d) and the potential fabrication violet-light-emitting devices.     

Synchrotron quantification of ultrasound cavitation and bubble dynamics in Al–10Cu melts

Knowledge of the kinetics of gas bubble formation and evolution under cavitation conditions in molten alloys is important for the control casting defects such as porosity and dissolved hydrogen. Using in situ synchrotron X-ray radiography, we studied the dynamic behaviour of ultrasonic cavitation gas bubbles in a molten Al–10 wt% Cu alloy. The size distribution, average radius and growth rate of cavitation gas bubbles were quantified under an acoustic intensity of 800 W/cm² and a maximum acoustic pressure of 4.5 MPa (45 atm). Bubbles exhibited a log-normal size distribution with an average radius of 15.3 ± 0.5 μm. Under applied sonication conditions the growth rate of bubble radius, R(t), followed a power law with a form of R(t) = αt^β, and α = 0.0021 & β = 0.89. The observed tendencies were discussed in relation to bubble growth mechanisms of Al alloy melts.     

Oxygen nonstoichiometry,mixed valency and mixed conduction in (La,Sr)(Co,Fe)O3−δ

Defect chemistry for a mixed conductor, La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ was studied. Samples were treated under controlled oxygen partial pressure, P(O₂), conditions at 1273 K [10^− 11.1 ≤ P(O₂)/atm ≤ 1], and cooled to room temperature. Oxygen nonstoichiometry and valences of transition metal ions for the treated samples were evaluated by iodometry and X-ray absorption spectroscopy, respectively. With decreasing P(O₂), preferential reduction of Co³⁺ to Co²⁺ was observed, while iron preserved its higher valence above 3 under conditions studied. A dependency of its electrical conductivity on P(O₂) was discussed along with a change in concentration of oxygen vacancies and mixed valences.     

Oxygen nonstoichiometry and defect structure of the double perovskite GdBaCo2O6 − δ

The results of oxygen nonstoichiometry, δ, measured by means of coulometric technique as a function of oxygen partial pressure, p_O2, in temperature range 900 ≤ T °C ≤ 1050 are presented for GdBaCo₂O_6 − δ with double perovskite structure. Partial molar enthalpy and entropy of oxygen in GdBaCo₂O_6 − δ structure were calculated. Both thermodynamic properties were shown to increase dramatically in the vicinity of the oxygen nonstoichiometry value equal to 1. The p_O2 dependences of oxygen nonstoichiometry and the δ dependences of the partial molar properties were found to have inflections when the oxygen content of GdBaCo₂O_6 − δ is equal to 5.0 exactly. The modeling of the defect structure of the double perovskite GdBaCo₂O_6 − δ was carried out by considering different reference states. Only the model based on the cubic perovskite GdCoO₃ as a reference state was shown to fit the experimental data on oxygen nonstoichiometry of GdBaCo₂O_6 − δ good enough. Equilibrium constants of the appropriate defects reactions were, therefore, determined. Concentrations of all defect species defined within the framework of this model were calculated as functions of temperature and oxygen nonstoichiometry. Oxygen vacancies were shown to be formed during p_O2 diminution in gas environment in the layers of GdBaCo₂O_6 − δ crystal lattice where they are ordered until oxygen nonstoichiometry of the oxide becomes equal to unity afterwards oxygen vacancies are formed randomly in oxygen polyhedrons.     

Stability information in plasma image of high-power CO2 laser welding

In deep penetration laser welding, a capillary called keyhole is formed when the energy intensity reaches 10⁶ W/cm². During this process, the vaporized metal and the surrounding atmosphere can be ionized to form plasma both in and above the keyhole. The stability of the keyhole has an important influence on the properties of welded components and the fluctuations of plasma. In this paper, a method was developed to acquire the stability information from plasma images taken by high-speed photography. The influences of surface impurity and the flowrate of side-assist gas on the stability were investigated. Bead-on-plate welding was performed on 12 mm E-grade shipbuilding steel plates using a 15 kW CO₂ laser, with helium as the blowing gas. Three characteristic parameters were used to evaluate the stability. It was found that these three characteristic parameters can effectively indicate the stability variation caused by the surface impurity and gas flowrate. The present research provides important insights into developing image-based sensors to monitor the welding process.     

Ultrasound-induced inactivation of gram-negative and gram-positive bacteria in secondary treated municipal wastewater

The effect of 24 kHz, high energy ultrasound in the presence and absence of titanium dioxide particles on the destruction of different bacteria groups was studied. Applying a total of 1500 W/L for 60 min (this corresponds to 5400 kJ/L specific nominal energy), the mean destruction of gram-negative bacteria such as total coliforms, faecal coliforms and Pseudomonas spp. was 99.5%, 99.2% and 99.7%, respectively. More recalcitrant to sonolytic inactivation were the gram-positive bacteria Clostridium perfringens and faecal streptococci with a mean removal of 66% and 84%, respectively. The presence of 5 g/L TiO₂ generally enhanced the destruction of gram-negative bacteria, yielding three to five logs reduction. On the other hand, the relatively weak sonochemical inactivation of gram-positive bacteria was only slightly affected by the presence of solid particles. Inactivation was found to follow first-order kinetics regarding bacteria population and was not affected significantly by the wastewater quality. Ultrasound irradiation at 4000 kJ/L specific nominal energy and in the presence of 5 g/L TiO₂ achieved less than 10³ CFU/100 mL total coliforms, thus meeting USEPA quality standards for wastewater reuse.     

Photo-resist ashing by atmospheric pressure glow discharge

Homogeneous glow plasma at atmospheric pressure without streamers and arcing was generated by making use of a radio-frequency (RF, 13.56 MHz) power supply. Oxygen gas was added to Ar/He gas as reactive agents for photo-resist (PR) ashing. The input power, flow rate, oxygen concentration, treatment time, substrate temperature are controlled for high ashing rate and uniform ashing. Thickness of PR film was measured by NANOSPEC (AFT200) and α-Step (P-10). An unstable discharge occurs destroying the uniformity, when the input power exceeds a threshold value determined from the distance between the substrate and plasma source. An increase of oxygen quantity or temperature increase makes high ashing rate, but the ashing surface is rugged. The PR ashing rate was related to oxygen atom in plasma. The number of treatment may not be important in PR ashing at the atmospheric pressure.     

Enhancement of oxygen surface kinetics of SrTiO3 by alkaline earth metal oxides

The kinetics of oxygen incorporation into semiconducting metal oxides such as strontium titanate are of particular interest for an application as a fast resistive-type oxygen sensor operating at high temperatures (T > 600 °C), e.g. in automotive exhaust gas monitoring.Based on a frequency-domain analysis of the response signal (resistance R) obtained from an electrically contacted sample exposed to a modulated oxygen partial pressure pO₂ in a fast kinetic measurement setup, the surface transfer controlled response behaviour of undoped and Fe-doped SrTiO₃ single crystals with thicknesses in the order of d = 45–125 μm was investigated with regard to the effect of thin PVD layers with alkaline earth (Ca, Sr, Ba) metal oxide compounds.The results of this electrical characterisation are compared with results obtained from ¹⁸O tracer exchange experiments and subsequent depth profile analysis by secondary ion mass spectrometry (SIMS). Both the electrical measurements and the ¹⁸O self-diffusion experiments revealed an enhancement of oxygen surface exchange kinetics in the case of all three alkaline earth metal oxides investigated.     

Oxygen permeation characteristics of zirconia with surface modification

Yttria-stabilized zirconia (YSZ) can be used as an oxygen-permeating membrane at elevated temperature (> 1400 °C) due to its chemical and mechanical stability. It was previously shown that the oxygen transport through YSZ membrane in reducing oxygen partial pressure (P_O2) was highly influenced by the surface-exchange kinetics that can be improved by porous surface coating layers such as YSZ, GDC (Gd-doped ceria) or YSZ–GDC mixture [H.J. Park, G.M. Choi, J. Eur. Ceram. Soc. 25 (2005) 2577]. However, the increased oxygen flux was still lower than that estimated assuming bulk-diffusion limit and rapidly decreased with time due to the sintering of coating layers and the reaction between bulk YSZ and coating layers. In this study, the oxygen fluxes through YSZ with LaCrO₃, GDC + LaCrO₃ (bilayer), LaCrO₃ + 5 wt.% GDC (mixture), or LaCr_0.7Co_0.3O₃ coatings were measured under controlled P_O2 gradient (permeate-side P_O2: ∼ 3 × 10^− 12 atm, feed-side P_O2: 2 × 10^− 10–2 × 10^− 8 atm) at 1600 °C. The oxygen flux drastically increased with these coatings. The highest increase in oxygen flux was shown with GDC + LaCrO₃ (bilayer) coating and was maintained for a long time. The presence of highly catalytic Ce ions while maintaining porous structure in the coating layer may explain the observation. The prevention of formation of resistive layer due to ceria coating may also be partly responsible for the observation.