Extraction and characterization of natural cellulosic fiber from Passiflora foetida stem

This article presents a comprehensive characterization study of natural cellulosic fiber extracted from Passiflora foetida vine stem. The chemical composition of the obtained P. foetida fibers (PFFs) comprised high cellulose (77.9 wt%) and low lignin (10.47 wt%) content and had distinctly higher crystallinity (67.36%) of cellulose, which was determined by an X-ray diffractometer. The PFFs exhibited good tensile strength of 248?942 MPa associated with elongation (1.38?4.67%) during tensile testing. Thermogravimetric analysis revealed that the PFFs are thermally stable up to 320°C with kinetic activation energy of 85.46 kJ mol^?1; hence they ensure their suitability as a reinforcing phase in composites for potential applications.     

Physicochemical properties of new cellulosic Artisdita hystrix leaf fiber

The characterization of new natural fiber is increasing due to its excellent properties. This drives investigators to create high performance composites. The present investigation was designed to study the physicochemical properties of fibers obtained from the leaf of the Artistida hystrix. The Artistida hystrix fibers (AHFs) had crystallinity index (44.85%), cellulose (59.54 wt%), hemicellulose (11.35 wt%), lignin (8.42 wt%), and density (540 kg m^?3). The tensile strength of AHFs was 440 ± 13.4 MPa with an average strain rate of 1.57 ± 0.04%. The calculated microfibril angle of AHFs was 12.64 ± 0.45°, which influenced the mechanical properties.     

Development of continuous process enabling nanofibrillation of pulp and melt compounding

Microfibrillated cellulose (MFC), a mechanically fibrillated pulp mostly consisting of nanofibrils, is a very attractive material because of its high elastic modulus and strength. Although much research has been done on composites of MFC and polypropylene (PP), it has been difficult to produce such composites at an industrial level because of the difficulties in using MFC in such composites are not only connected to the polarity (that can be improved with compatibilizers), but also with the challenge to make a homogeneous blend of the components, and also the low temperature stability of cellulose that could cause problems during processing. We developed a new processing method which enables continuous microfibrillation of pulp and its melt compounding with PP. Never-dried kraft pulp and powdered PP were used as raw materials to obtain MFC by kneading via a twin-screw extruder. Scanning electron microscopy showed nano to submicron wide fibers entangled in the powdered PP. MFC did not aggregate during the melt compounding process, during which the water content was evaporated. Maleic anhydride polypropylene (MAPP) was used as a compatibilizer to reinforce interfacial adhesion between the polar hydroxyl groups of MFC and non-polar PP. We investigated the effect of MAPP content on the mechanical properties of the composite, which were drastically improved by MAPP addition. Needle-leaf unbleached kraft pulp (NUKP)-derived MFC composites had better mechanical properties than needle-leaf bleached kraft pulp (NBKP)-derived MFC composites. Injection molded NUKP-derived MFC composites had good mechanical and thermal properties. The tensile modulus of 50 wt% MFC composite was two times, and the tensile strength 1.5 times higher than that of neat PP. The heat distortion temperature of 50 wt% MFC content composite under 1.82 MPa flexural load was increased by 53 °C, from 69 to 122 °C. This newly developed continuous process using powder resin has the potential for application at an industrial level.     

Rheological,morphological and mechanical properties of flax fiber polypropylene composites: influence of compatibilizers

In this work, the rheological, mechanical and morphological properties of flax fiber polypropylene composites were investigated. The effect of incorporating a polypropylene grafted acrylic acid or a polypropylene grafted maleic anhydride on these properties has been studied as well. According to scanning electron microscopic observations and tensile tests, the addition of a compatibilizer improved the interfacial adhesion between the flax fibers and the polymer matrix. The tensile modulus of composite containing 30 wt% flax fibers was improved by 200 % and the tensile strength improved by 60 % in comparison with the neat PP. Plasticizing effect of the compatibilizers as a result of their lower melt flow index was also shown to decrease the rheological properties of the composites, even though the effect was not pronounced on the mechanical properties.     

Thermogravimetry on wood powder-filled polyurethane composites derived from lignin

Novel polyurethane (PU) composites whose matrix is derived from lignin, molasses polyol and filler from wood powder were successfully prepared. Two kinds of polyol were mixed 0/100 to 100/0 in seven steps, and filler content was varied from 50 to 100 mass % to polyol content. Decomposition behaviour of PU composites was investigated by thermogravimetry. Apparent density and mechanical properties of the above composites were also measured. Surface texture was observed by scanning electron microscopy. Thermal decomposition of PU composites was found to occur in two stages. The first decomposition observed at 570–580 K (DT _d1, peak temperature of derivative curve) is attributed to the matrix of composites. The second stage decomposition depending on filler content, observed in a temperature range from 590 to 630 K (DT _d2), is attributable to filler homogenously associated with PU matrix. Marked differences were not found, when the kinds of lignin and molasses polyol composition were varied. The above PU composites were found to be thermally stabilised by the introduction of filler.     

Thermomechanical and crystallization behavior of polylactide-based flax fiber biocomposites

In this work, the rheological, thermal and mechanical properties of melt-compounded flax fiber-reinforced polylactide composites were investigated. The effect of compounding on fiber length and diameter, and the relationship between fiber content and the crystallization behavior of the biocomposites, at various temperatures, were also examined. After melt-compounding, fiber bundles initially present were, to a large extent, broken into individual fibers and the fiber length was decreased by 75 %, while the aspect ratio was decreased by nearly 50 %. The crystallization half-time was found to decrease with increasing flax fiber content, and showed a minimum value at 105 °C for all systems. The elastic modulus was increased by 50 % in the presence of 20 wt% flax fibers. The addition of maleic anhydride-grafted polylactide had a positive effect on the mechanical properties of the biocomposite. This system is particularly interesting in the context of sustainable development as it is entirely based on renewable resources and biodegradable.     

Mechanical and thermal properties of Acacia leucophloea fiber/epoxy composites: Influence of fiber loading and alkali treatment

In this work, the influence of fiber content and alkali treatment on the mechanical and thermal properties of Acacia leucophloea fiber-reinforced epoxy composites was studied. Ten composite samples were fabricated by varying fiber content (5, 10, 15, 20, and 25 wt%); both untreated and treated fiber were soaked in a 5% NaOH solution for 45 min by using hand-layup method. The composite reinforced with 20 wt% treated fiber content exhibited better mechanical properties and thermal properties. Fourier transform infrared analysis, morphological analysis by atomic force microscope, and scanning electron microscope of composites were also performed.     

Nanofibrillated cellulose/nanographite composite films

Though research into nanofibrillated cellulose (NFC) has recently increased, few studies have considered co-utilising NFC and nanographite (NG) in composite films, and, it has, however been a challenge to use high-yield pulp fibres (mechanical pulps) to produce this nanofibrillar material. It is worth noting that there is a significant difference between chemical pulp fibres and high-yield pulp fibres, as the former is composed mainly of cellulose and has a yield of approximately 50 % while the latter is consist of cellulose, hemicellulose and lignin, and has a yield of approximately 90 %. NFC was produced by combining TEMPO (2,2,6,6-tetramethypiperidine-1-oxyl)-mediated oxidation with the mechanical shearing of chemi-thermomechanical pulp (CTMP) and sulphite pulp (SP); the NG was produced by mechanically exfoliating graphite. The different NaClO dosages in the TEMPO system differently oxidised the fibres, altering their fibrillation efficiency. NFC–NG films were produced by casting in a Petri dish. We examine the effect of NG on the sheet-resistance and mechanical properties of NFC films. Addition of 10 wt% NG to 90 wt% NFC of sample CC2 (5 mmol NaClO CTMP-NFC homogenised for 60 min) improved the sheet resistance, i.e. from that of an insulating pure NFC film to 180 Ω/sq. Further addition of 20 (CC3) and 25 wt% (CC4) of NG to 80 and 75 wt% respectively, lowered the sheet resistance to 17 and 9 Ω/sq, respectively. For the mechanical properties, we found that adding 10 wt% NG to 90 wt% NFC of sample HH2 (5 mmol NaClO SP-NFC homogenised for 60 min) improved the tensile index by 28 %, tensile stiffness index by 20 %, and peak load by 28 %. The film’s surface morphology was visualised using scanning electron microscopy, revealing the fibrillated structure of NFC and NG. This methodology yields NFC–NG films that are mechanically stable, bendable, and flexible.     

Residual lignin inhibits thermal degradation of cellulosic fiber sheets

The market for cellulosic fiber based food packaging applications is growing together with the importance of improving the thermal durability of these fibers. To shed light on this, we investigated the role of residual lignin in pulp on the thermal stability of refined pulp sheets. The unbleached, oxygen delignified, and fully bleached pulp sheets were studied after four separate refining degrees. Comparison by Gurley air resistance, Bendtsen porosity, and the oxygen transmission rate tests showed that lignin containing sheets had better air and oxygen barrier properties than fully bleached sheets. Sheet density and light scattering coefficient measurements further confirmed that the lignin containing pulps underwent more intense fibrillation upon refining that changed the barrier properties of the sheets. Thermal treatments (at 225 °C, 20 and 60 min, in water vapor atmospheres of 1 and 75 v/v %) were applied to determine the thermal durability of the sheets. The results revealed that the residual lignin in pulps improved the thermal stability of the pulp sheets in the hot humid conditions. This effect was systematically studied by tensile strength, brightness, and light absorption coefficient measurements. The intrinsic viscosity results support the findings and suggest that lignin is able to hinder the thermal degradation of pulp polysaccharides. In spite of the fact that lignin is known to enhance the thermal yellowing of paper, no significant discoloration of the pulp sheets containing residual lignin was observed in the hot humid conditions (75 v/v %). Our results support the idea of lignin strengthening the thermal durability of paper.     

Enzymatic hydrolysis of mercerized and unmercerized sisal pulp

Enzymatic saccharification of sisal cellulosic pulp has been investigated. Brazil leads global production of lignocellulosic sisal fiber, which has high cellulose content, an important property for producing glucose via saccharification. Hence, sisal pulp can be a good alternative for use in biorefineries. Prior to enzymatic hydrolysis, the starting pulp [85 ± 2% α-cellulose, 15 ± 2% hemicelluloses, 1.2 ± 2% insoluble lignin, viscometric average molar mass (MMvis) 19,357 ± 590 g mol^?1, crystallinity index (CI) 74%] was pretreated with alkaline aqueous solution (mercerization, 20 g of pulp L^?1, 20% NaOH, 50 °C). The changes in the properties of the cellulosic pulp during this pretreatment were analyzed [α-cellulose content, MMvis, CI, pulp fiber dimensions, and scanning electron microscopy (SEM)]. The unmercerized and mercerized (97.4 ± 2% α-cellulose, 2.6 ± 2% hemicelluloses, 0.3 ± 0.1% insoluble lignin, MMvis 94,618 ± 300 g mol^?1, CI 68%) pulps were subjected to enzymatic hydrolysis (48 h, commercial cellulase enzymes, 0.5 mL g^?1 pulp); during the reactions, aliquots consisting of unreacted pulp and liquor were withdrawn from the medium at certain times and characterized (unreacted pulp: MMvis, CI, fiber dimensions, SEM; liquor: high-performance liquid chromatography). The changes in pulp properties observed during mercerization facilitated access of enzymes to cellulose chains, and the yield of the hydrolysis reaction increased from 50.2 (unmercerized pulp) to 89.0% (mercerized pulp). These initial results for enzymatic hydrolysis of sisal pulp indicate that it represents a good alternative biomass for bioethanol production.     

Characterization of new natural cellulosic fiber from the Ipomoea staphylina plant

Natural fibers extracted from plants play a major role as reinforcement in polymer composite materials due to their superior properties. This work aims to comprehensively characterize the physical and chemical properties of Ipomoea staphylina fibers (ISFs), which are extracted from the stem of the Ipomoea staphylina plant. The ISFs show cellulose content (72.76 wt%), hemicelluloses content (13.6 wt%), density (1401 kg cm^?3), and tensile strength of 173–658 MPa with a strain rate of 2.03–6.63%. The thermal stability of ISFs illustrate that the fibers are stable up to a temperature of 311°C with kinetic activation energy of 99.82 kJ mol^?1.     

The influence of chemical treatment on the mechanical properties of windmill palm fiber

Bleached palm fiber without lignin, alkalized palm fiber without hemicelluloses and raw windmill palm fiber were prepared. Then, the chemical composition and the mechanical properties of the windmill palm fiber were investigated. Scanning electron microscopy, Fourier transform infrared spectroscopy and Raman microscopy were employed to characterize the structure and chemical composition. A universal material tester, nanoindentation and dynamic mechanical analysis were used to study the mechanical property of these samples. According to the results, bleach treatment removed most of the silica bodies as well as the lignin, smoothed the fiber surfaces and increased the hollowness to 50%. Alkali treatment removed most of the hemicelluloses, increased the surface roughness, and reduced the hollowness to 28%. Alkalized fibers have the highest tensile strength, elongation at break and elastic modulus, with values of 119.37 ± 27.21 MPa, 30.58 ± 5.87% and 10.75 ± 4.30 GPa, respectively. The raw material without treatment has the highest stiffness, while the alkalized samples are the most flexible fibers and sensitive to temperature.     

The effect of chemical and physical characteristics of spruce SEW pulps on enzymatic hydrolysis

Conifers, which are the most abundant biomass species in Nordic countries, USA, Canada and Russia, exhibit strong resistance towards depolymerization by cellulolytic enzymes. At present, it is still not possible to isolate a single structural feature which would govern the rate and degree of enzymatic hydrolysis. On the other hand, the forest residues alone represent an important potential for biochemical production of biofuels. In this study, the effect of substrate properties on the enzymatic hydrolysis of softwood was studied. Stem wood spruce chips were fractionated by SO₂–ethanol–water (SEW) treatment to produce pulps of varying composition by applying different operating conditions. The SEW technology efficiently fractionates different types of lignocellulosic biomass by rapidly dissolving hemicelluloses and lignin. Cellulose remains fully in the solid residue which is then treated by enzymes to release glucose. The differences in enzymatic digestibility of the spruce SEW pulp fibers were interpreted in terms of their chemical and physical characteristics. A strong correlation between the residual lignin content of SEW pulp and enzymatic digestibility was observed whereas cellulose degree of polymerization and hemicellulose content of pulp were not as important. For the pulps containing about 1.5 % (w/w) lignin, 90 % enzymatic digestibility was achieved at 10 FPU enzyme charge and 24 h of hydrolysis time.     

Effect of fiber length and composition on mechanical properties of carbon fiber‐reinforced polybenzoxazine

The mechanical strength and modulus of chopped carbon fiber (CF)‐reinforced polybenzoxazine composites were investigated by changing the length of CFs. Tensile, compressive, and flexural properties were investigated. The void content was found to be higher for the short fiber composites. With increase in fiber length, tensile strength increased and optimized at around 17 mm fiber length whereas compressive strength exhibited a continuous diminution. The flexural strength too increased with fiber length and optimized at around 17 mm fiber length. The increase in strength of composites with fiber length is attributed to the enhancement in effective contact area of fibers with the matrix. The experimental results showed that there was about 350% increase in flexural strength and 470% increase in tensile strength of the composites with respect to the neat polybenzoxazine, while, compressive properties were adversely affected. The composites exhibited an optimum increase of about 800% in flexural modulus and 200% in tensile modulus. Enhancing the fiber length, leads to fiber entanglement in the composites, resulted in increased plastic deformation at higher strain. Multiple branch matrix shear, debonded fibers and voids were the failures visualized in the microscopic analyses. Defibrillation has been exhibited by all composites irrespective of fiber length. Fiber debonding and breaking were associated with short fibers whereas clustering and defibrillation were the major failure modes in long fiber composites. Increasing fiber loading improved the tensile and flexural properties until 50–60 wt% of fiber whereas the compressive property consistently decreased on fiber loading. Copyright © 2008 John Wiley & Sons, Ltd.     

Extraction and characterization of alkali-treated red coconut empty fruit bunch fiber

This article discusses the extraction and characterization of new natural fiber extracted from red coconut empty fruit bunch. The physicochemical, mechanical, and thermal properties of alkali-treated red coconut empty fruit bunch fibers (ARCEFBFs) were reported and compared with other natural fibers for the first time. Cellulose content (65.02 wt%), wax (0.32 wt%), density (1.421 g/cc), and tensile strength (1299.49 MPa) were identified in ARCEFBFs. Fourier transform infrared spectroscopy and X-ray diffraction analysis confirmed that ARCEFBFs are rich in cellulose content with crystallinity index of 53.6%. Thermogravimetric analysis revealed that these fibers are thermally stable until 270.48°C.     

Effect of fiber drying on properties of lignin containing cellulose nanocrystals and nanofibrils produced through maleic acid hydrolysis

The effect of fiber drying on the properties of lignin containing cellulose nanocrystals (LCNC) and nanofibrils (LCNF) produced using concentrated maleic acid hydrolysis of a never dried unbleached mixed hardwood kraft pulp was evaluated. Two drying conditions, i.e., air drying and heat drying at 105 °C were employed. It was found that drying (both air and heat) enhanced acid hydrolysis to result in slightly improved LCNC yields and less entangled LCNF. This is perhaps due to the fact that drying modified the cellulose supermolecular structure to become more susceptible to acid hydrolysis and the enhanced hydrolysis severity at the fiber surface when using dried fibers. Drying substantially improved LCNC crystallinity and LCNF suspension viscoelastic behavior. The present study quantitatively elucidated the effect of pulp drying (either air or heat) on producing cellulose nanomaterials and has practical importance because commercial market pulp (heat dried) is most likely to be used commercially.     

Characterization of new natural cellulosic fiber from kusha grass

The present research work aimed to characterize new natural cellulosic kusha fibers extracted from the kusha grass plants. The physical and chemical properties of kusha fibers such as cellulose content (70.58%), lignin (14.35%), wax content (1.52%), ash content (2.46%), moisture content (8.01%), and density (1.1025 g cc^?1) were identified. An X-ray diffraction of kusha fibers confirms the presence of cellulose with a crystalline index of 55.4%. Fourier transform infrared spectroscopy analysis was carried out to establish the certainty of using them as reinforcement fiber. Thermogravimetric analysis ensures thermal stability up to 357°C which is within the polymerization process temperature.     

Ionic liquid extraction method for upgrading eucalyptus kraft pulp to high purity dissolving pulp

High purity cellulose from wood is an important raw material for many applications such as cellulosic fibers, films or the manufacture of various cellulose acetate products. Hitherto, multi-step refining processes are needed for an efficient hemicellulose removal, most of them suffering from severe cellulose losses. Recently, a novel method for producing high purity cellulose from bleached paper grade birch kraft pulp was presented. In this so called IONCELL process, hemicelluloses are extracted by an ionic liquid–water mixture and both fractions can be recovered without yield losses or polymer degradation. Herein, it is demonstrated that bleached Eucalyptus urograndis kraft pulp can be refined to high purity acetate grade pulp via the IONCELL process. The hemicellulose content could be reduced from initial 16.6 to 2.4 wt% while persevering the cellulose I crystal form by using an optimized 1-ethyl-3-methylimidazolium dimethylphosphate-water mixture as the extraction medium. The degree of polymerization was then reduced by a sulfuric acid treatment for subsequent acetylation of the pulp, resulting in a final hemicellulose content of 2.2 wt%. When pre-treating the pulp enzymatically with endoxylanase, the final hemicellulose content could be reduced even to 1.7 wt%. For comparison, the eucalyptus kraft pulp was also subjected to cold caustic extraction and the same subsequent acid treatment which led to 3.9 wt% of residual hemicelluloses. The performance in acetylation of all produced pulps was tested and compared to commercial acetate grade pulp. The endoxylanase-IONCELL-treated pulp showed superior properties. Thus, an ecologically and economically efficient alternative for the production of highest value cellulose pulp is presented.     

Improved mechanical properties of epoxy composites reinforced with surface‐treated UHMWPE fibers

The surface treatment of ultra‐high molecular weight polyethylene fiber using potassium permanganate and the mechanical properties of its epoxy composites were studied. After treatment, many changes were happened in the fiber surface: more O‐containing groups (―OH, ―C═O, and ―C―O groups), drastically decreased contact angles with water and ethylene glycol, slightly increased melting point and crystallinity, and formed cracks. Different contents (0.1–0.5 wt%) ultra‐high molecular weight polyethylene fibers/epoxy composites were prepared. The results indicated that the surface treatment decreased the tensile strength of epoxy composites, but increased the bending strength. When the fiber content was 0.3 wt%, the above properties reached the maximum. At the same fiber content, the interlaminar shear strength of the composites was increased by 26.6% up to the as‐received fiber composites. Dynamic mechanical analysis of the composites suggested the storage modulus and tanδ were decreased due to the surface treatment. Fractured surface analysis confirmed that the potassium permanganate treatment was effective in improving the interface interaction.     

Optimization of short Indian Areca fruit husk fiber (Areca catechu L.)–reinforced polymer composites for maximizing mechanical properties

Natural fibers are being used as reinforcing materials for polymer composites due to their eco-friendly properties. Areca fruit husk fiber (AFHF) is one such fiber; it is currently discarded waste from the tobacco industry, but has huge potential. It is light in weight with a perforated surface that enables good bonding with a polymer matrix. In this study, comprehensive characterization of physical, chemical, thermal, mechanical, and microstructural properties was carried out on the fiber and the composite made with that fiber to optimize the fiber content. The optimum fiber content is found to be 40 wt.%, whereas beyond that, fiber pull-out and debonding reduces the load-bearing capacity of the composite. The specific properties of AFHF polymer composite are even higher than that of the popular E-glass fiber composite, which positions AFHF composite as an alternative structural material.