Fluorescence of N,N′-dimethylaminobenzonitrile in polyvinyl alcohol stretched films

We have demonstrated that the conditions of the charge-transfer (CT) reaction in the N,N′-dimethylaminobenzonitrile (DMABN) molecule in polyvinyl alcohol (PVA) polymer matrices can be considerably changed upon their stretching deformation. The fluorescence spectrum of DMABN in PVA has two characteristic bands in the ultraviolet (UV) and visible spectral ranges, which indicates that a CT reaction proceeds in the excited state. Stretching leads to a strong decrease in the intensity of the UV band, the contribution of which in undeformed samples is comparable with the emission in the violet range. Even single stretching PVA films strongly reduces the emission intensity of the UV band, with this effect being dramatically enhanced upon sixfold stretching. In the latter case, The fluorescence spectrum is characterized by a strong CT band, the relative intensity of which is 3.5 times higher than even in a strongly polar aprotic solvent, such as acetonitrile. The obtained data indicate that, as a result of mechanical stretching, it becomes possible to change basic intermolecular factors that affect the CT rate in PVA samples.     

ESR study on radiation chemical processes in polyvinyl alcohol films at 77°k

Abstract

Trapped electrons (e_t ^?) were detected in irradiated PVA films at 77°K. Yield of e_t ^? was decreased as evaporating water from the films, indicating that water molecules contribute to construct pre-existing traps in the polymer. The radical produced at 77°K was identified as a precursor of the radical produced at room temperature.     

Structural and dielectric properties of polyvinyl alcohol/barium zirconium titanate polymer–ceramic composite

The polyvinyl alcohol (PVA)/barium zirconium titanate Ba[Zr_0.1Ti_0.9]O₃ (BZT) polymer–ceramic composites with different volume percentage are obtained from solution mixing and hot-pressing method. Their structural and electrical properties are characterized by X-ray diffraction (XRD), Rietveld refinement, cluster modeling, scanning electron microscope and dielectric study. XRD patterns of PVA/BZT polymer–ceramics composite (with 50% volume fractions) indicate no obvious differences than the XRD patterns of pure BZT which shows that the crystal structure is still stable in the composite. The scanning electron micrograph indicates that the BZT ceramic is dispersed homogeneously in the polymer matrix without agglomeration. The dielectric permittivity (ε_r) and the dielectric loss (tan δ) of the composites increase with the increase of the volume fraction of BZT ceramic. Theoretical models are employed to rationalize the dielectric behavior of the polymer composites. The dielectric properties of the composites display good stability within a wide range of temperature and frequency. The excellent dielectric properties of these polymer–ceramic composites indicate that the BZT/PVA composites can be a candidate for embedded capacitors.     

Investigations on Fe doped polyvinyl alcohol films with and without gamma (γ)-irradiation

This paper deals with the preparation of pure and ferric chloride (FeCl₃) doped polyvinyl alcohol (PVA) films by solution casting method. Optical and electrical properties were systematically investigated. We have found the decrease in optical band gap energy of PVA films on doping FeCl₃. The optical band gap energy values in the present work are found to be 3.10 eV for pure PVA, 2 eV for PVA:Fe³⁺ (5 mol%), 1.91 eV for PVA:Fe³⁺(15 mol%) and 1.8 eV for PVA:Fe³⁺(25 mol%). Direct current electrical conductivity (σ) of pure, FeCl₃ doped PVA films in the temperature range 70-127 °C has been studied. At 387 K dc electrical conductivity of pure PVA film is 5.5795 μ Ω⁻¹ cm⁻¹, PVA:Fe³⁺ (5 mol%) film is 10.0936 μ Ω⁻¹ cm⁻¹ and γ-Irradiated PVA:Fe³⁺ (5 mol%) film for 900 CGY/min is 22.1950 μ Ω⁻¹ cm⁻¹. The result reveals the enhancement of the electrical conductivity with γ-irradiation. FT-IR study signifies the intermolecular hydrogen bonding between Fe³⁺ ions of FeCl₃ with OH group of PVA.     

Studies on structural,optical and cluster size of poly(m-toluidine)–polyvinyl chloride blends

Poly(m-toluidine) (PmT), a derivative of polyaniline, has been prepared by chemical oxidation polymerization method. The synthesized PmT powder is blended with plasticized polyvinyl chloride (PVC) to achieve 20 μm thick self-supported films. These films were irradiated with 60 MeV Si⁵⁺ ions at three different fluences whose S _e (electronic energy loss) value is found to be 1.988×10³ KeV/μ m, an order of magnitude larger than 60 MeV C⁵⁺ (2.958×10² KeV/μ m). Fourier transform infrared (FTIR), X-ray diffraction (XRD) and ultraviolet-visible (UV) absorption studies of pre- and post-irradiated films of PmT–PVC blends were carried out to study the heavy ion irradiation effects on these polymer blends. An overall change in the structure of the polymer blend has been observed from FTIR studies. UV-visible spectra show a decrease in the optical band gap (E _g) and an increase in cluster size with increasing fluence. An effort is made to compare these results with our earlier studies. We found that the variation in S _e plays an important role in the structural and optical properties of PmT–PVC blends.     

Structural,thermal and electrical properties of polyvinyl alcohol/poly(vinyl pyrrolidone)–sodium nitrate solid polymer blend electrolyte

Sodium ion conducting solid polymer blend electrolyte thin films have been prepared by using polyvinyl alcohol (PVA)/poly(vinyl pyrrolidone) (PVP) with NaNO₃ by solution cast technique. The prepared films were characterized by various methods. The complexation of the salt with the polymer blend was identified by X-ray diffraction (XRD) and Fourier transforms infrared spectroscopy (FTIR), Differential scanning calorimetry was used to analyze the thermal behavior of the samples, and the glass transition temperature is low for the highest conducting polymer material. The scanning electron microscopy gives the surface morphology of the polymer electrolytes. The frequency and temperature dependent of electrical conductivities of the films were studied using impedance analyzer in the frequency range of 1 Hz to 1 MHz. The highest electrical conductivity of 50PVA/50PVP/2 wt% NaNO₃ concentration has been found to be 1.25 × 10^?5 S cm^?1 at room temperature. The electrical permittivity of the polymer films have been studied for various temperatures. The transference number measurements showed that the charge transport is mainly due to ions than electrons. Using this highest conducting polymer electrolyte, an electrochemical cell is fabricated and the parameters of the cells are tabulated.     

Optical properties of polyvinyl alcohol doped (Se80Te20)100–xAgx (0 ≤ x ≤ 4) composites

Polyvinyl alcohol (PVA) doped (Se₈₀Te₂₀)_100–xAg_x (0 ≤ x ≤ 4) thin films were prepared by the spin-coating technique on a quartz substrate. The optical parameters of PVA-doped (Se₈₀Te₂₀)_100–xAg_x (0 ≤ x ≤ 4) composites at the same chalcogen concentration (S₀ = 0.1 mg ml^?1) and PVA/(Se₈₀Te₂₀)₉₆Ag₄ composites at three different chalcogen concentrations viz. S₁ = 0.3 mg ml^?1, S₂ = 0.6 mg ml^?1 and S₃ = 1 mg ml^?1 have been studied. The semi-crystalline nature of the as-deposited thin filmsisdetermined by X-ray diffraction. The transmission and reflection spectra of PVA-doped Se–Te–Ag thin films were obtained in a 350–650 nm spectral region. The optical-band gap has been calculated from the transmission and reflection data. The refractive index has been calculated by the measured reflection data. It has been found that the optical-band gap increases, but the refractive index, extinction coefficient, and the real and imaginary parts of the dielectric constant decrease, with increase in Agcontent in PVA-doped (Se₈₀Te₂₀)_100–xAg_x (0 ≤ x ≤ 4) thin films. Such type of behavior is explained on the basis of decrease in density of the defect states. However, the optical-band gap has been found to be decreased and all other optical parameters show increase in their values with increase in concentration of (Se₈₀Te₂₀)₉₆Ag₄ glass in PVA-doped composites. The results have been explained on the basis of cluster-size formation at the time of dissolution. This study shows that the optical properties of new composites are affected by the change in silver and chalcogen concentration.     

Effect of sodium alginate modification of graphene (by ‘anion-π’ type of interaction) on the mechanical and thermal properties of polyvinyl alcohol (PVA) nanocomposites

Layered aligned dispersion of graphene in graphene/polyvinyl alcohol (PVA) nanocomposites is prepared in the form of films through simple solution processing route. The results indicate that there exist an interfacial interaction between PVA and graphene because of hydrogen bonding. This is responsible for the change in structure of PVA (such as decrease in the level of crystallization) and exhibiting ductile PVA nanocomposite film with improved tensile modulus, tensile strength, and thermal stability. Moreover, to improve the mechanical properties of PVA nanocomposites, graphene is successfully modified using a non-covalent modifier, sodium alginate (SA) and there exist an ‘anion-π’ type of interaction in between SA and graphene. The modification results in finer dispersion of the graphene in PVA/SA-m-graphene nanocomposites. In addition, there exist a hydrogen bonding in between PVA and SA. This has resulted in the remarkable improvement in mechanical properties of PVA/SA-m-graphene nanocomposites as compared to pure PVA and PVA/graphene nanocomposites. The increase in mechanical properties of PVA/SA-m-graphene nanocomposites is achieved through better load transfer from graphene to polymer matrix, despite decrease in crystallinity of PVA. Improvement in tensile modulus and tensile strength is highest at 0.5 wt.% of SA-modified graphene in PVA/SA-m-graphene nanocomposites because of finer dispersion of graphene and is 62 and 40% higher than that of pure PVA. Addition of SA-modified graphene also improves the thermal stability of PVA/SA-m-graphene nanocomposites remarkably as compared to unmodified graphene PVA nanocomposites.     

Effect of series resistance and interface states on the I-V, C-V and G/ω-V characteristics in Au/Bi-doped polyvinyl alcohol (PVA)/n-Si Schottky barrier diodes at room temperature

The forward and reverse bias current-voltage (I-V), capacitance-voltage (C-V) and conductance-voltage (G/ω-V) characteristics of the Au/PVA (Bi-doped)/n-Si Schottky barrier diodes (SBDs) have been investigated at room temperature by taking the interface states (N_ss) and series resistance (R_s) effects into account. The voltage dependent profiles of resistance (R_i) were obtained from both the I-V and C/G-V measurements by using Ohm’s Law and Nicollian methods. The obtained values of R_i with agreement each other especially at sufficiently high bias voltages which correspond the value of R_s of the diode. Therefore, the energy density distribution profile of N_ss was obtained from the forward bias I-V data taking the bias dependence of the effective barrier height (BH) Φ_e and R_s into account. The high value of ideality factor (n) was attributed to high density of N_ss and interfacial polymer layer at metal/semiconductor (M/S) interface. In order to examine the frequency dependence of some of the electrical parameters such as doping donor concentration (N_D), Φ_e, R_s and N_ss values, C-V and G/ω-V measurements of the diode were performed at room temperature in the frequency range of 50 kHz-5 MHz. Experimental results confirmed that the N_ss, R_s and interfacial layer are important parameters that influence electrical characteristics of SBD.