Effect of residual water and free volume on the glass‐transition temperature and heat capacity in polystyrene/poly(vinyl acetate‐co‐butyl acrylate) structured latex films

The dynamic heat capacity and glass‐transition temperature of polystyrene (PS)/poly(vinyl acetate‐co‐butyl acrylate) (VAc–BA) (50:50 w/w) structured latex films as a function of annealing time at 70, 77, and 85 °C were examined with modulated‐temperature differential scanning calorimetry. The PS and poly(vinyl acetate‐co‐n‐butyl acrylate) components were considered to be the cores and shells, respectively, in the structured latex. The dynamic heat capacity decreased with time. The glass‐transition temperatures of the PS and VAc–BA phases shifted to higher values after annealing. The results of thermogravimetry showed that there existed about 1.8% residual water in the films. The mean free volume and relative concentration of holes at room temperature (before and after annealing) and 85 °C, as a function of time, were obtained with positron annihilation lifetime spectroscopy (PALS). The PALS results indicated no significant change in free volume during annealing. It is believed that the loss, by diffusion, of residual water mainly caused a decrease in heat capacity and an increase in the glass‐transition temperatures. As little as 1.8% residual water in the structured latex films had a significant influence on the thermal properties. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1659–1664, 2001     

Synthesis of bio‐based poly(ethylene 2,5‐furandicarboxylate) copolyesters: Higher glass transition temperature,better transparency,and good barrier properties

The bio‐based polyester, poly(ethylene 2,5‐furandicarboxylate) (PEF), was modified by 2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol (CBDO) via copolymerization and a series of copolyesters poly(ethylene‐co‐2,2,4,4‐tetramethyl‐1,3‐cyclobutanediol 2,5‐furandicarboxylate)s (PETFs) were prepared. After their chemical structures and sequence distribution were confirmed by nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR), their thermal, mechanical, and gas barrier properties were investigated in detail. Results showed that when the content of CBDO unit in the copolyesters was increased up to 10 mol%, the completely amorphous copolyesters with good transparency could be obtained. In addition, with the increasing content of CBDO units in the copolyesters, the glass transition temperature was increased from 88.9 °C for PET to 94.3 °C for PETF‐23 and the tensile modulus was increased from 3000 MPa for PEF to 3500 MPa for PETF‐23. The barrier properties study demonstrated that although the introduction of CBDO units would increase the O₂ and CO₂ permeability of PEF slightly, PECF‐10 still showed better or similar barrier properties compared with those of PEN and PEI. In one word, the modified PEF copolyesters exhibited better mechanical properties, higher glass transition temperature, good barrier properties, and better clarity. They have great potential to be the bio‐based alternative to the popular petroleum‐based poly(ethylene terephthalate) (PET) when used as the beverage packaging materials. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3298–3307     

Free volume and oxygen transport in cold‐drawn polyesters

Poly(ethylene terephthalate) (PET), poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) (PETBB55), and poly(ethylene 2,6‐naphthalate) (PEN) were cold‐drawn to achieve uniform extension without crystallization or stress whitening, and oxygen transport properties were studied at temperatures from 10 to 40 °C. Correlation of oxygen solubility and polymer specific volume made it possible to consider the oriented polyester as a one‐phase densified glass. Orientation was viewed as decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium condition. Between 10 and 40 °C, the amount of excess‐hole free volume in PET decreased as the polymer approached the glass transition temperature. In contrast, temperature changes in this range had little effect on the excess‐hole free volume in PETBB55 and PEN, which were well below their glass transition temperature. Gas diffusion was viewed as discrete jumps of the oxygen molecule between holes of excess‐free volume. The jump length was extracted from the activation energy for diffusion according to a channel‐formation model. The result agreed well with the hole spacing estimated from a simple lattice model using the hole density reported in the literature. Extending the lattice model to estimate the mean excess‐free volume hole radius from the fractional free volume resulted in good correlation with the hole radius obtained from positron annihilation lifetime spectroscopy. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 493–504, 2004     

Micelle formation and sol–gel transition behavior of comb‐like amphiphilic poly((PLGA‐b‐PEG)MA) copolymers

Comb‐like amphiphilic poly(poly((lactic acid‐co‐glycolic acid)‐block‐poly(ethylene glycol)) methacrylate (poly((PLGA‐b‐PEG)MA)) copolymers were synthesized by radical polymerization. (PLGA‐b‐PEG)MA macromonomer was prepared by ring‐opening bulk polymerization of DL ‐lactide and glycolide using purified poly(ethylene glycol) monomethacrylate (PEGMA) as an initiator. (PLGA‐b‐PEG)MA macromonomer was copolymerized with PEGMA and/or acrylic acid (AA) by radical polymerization to produce comb‐like amphiphilic block copolymers. The molecular weight and chemical structure were investigated by GPC and ¹H NMR. Poly((PLGA‐b‐PEG)MA) copolymer aqueous solutions showed gel–sol transition behavior with increasing temperature, and gel‐to‐sol transition temperature decreased as the compositions of the hydrophilic PEGMA and AA increased. The gel‐to‐sol transition temperature of the terpolymers of the poly((PLGA‐b‐PEG)MA‐co‐PEGMA‐co‐AA) also decreased when the pH was increased. The effective micelle diameter obtained from dynamic light scattering increased with increasing temperature and with increasing pH. The critical micelle concentration increased as the composition of the hydrophilic monomer component, PEGMA and AA, were increased. The spherical shape of the hyperbranched polymers in aqueous environment was observed by atomic force microscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1954–1963, 2008     

Polyesters analogous to PET and PBT based on O‐benzyl ethers of xylitol and L‐arabinitol

The synthesis, characterization, and some properties of new copolyesters of poly(butylene terephthalate) (PBT) and poly(ethylene terephthalate) (PET) based on L ‐arabinitol and xylitol are described. These copolyesters were obtained by polycondensation reaction in the melt of mixtures of 1,4‐butanediol or ethylene glycol and 2,3,4‐tri‐O‐benzyl‐L ‐arabinitol or 2,3,4‐tri‐O‐benzyl‐xylitol with dimethyl terephthalate. Their weight‐average molecular weights ranged between 7000 and 55,000, with polydispersities ranging from 1.4 to 4.7. Copolymers containing 1,4‐butanediol could be analyzed by NMR, and were found to have a statistical microstructure. All these copolyesters were thermally stable, with degradation temperatures well above 300 °C. With increasing amounts of alditol in the copolyester, the melting temperature and crystallinity decreased in both series, and the glass transition temperature increased for the PBT series and decreased for the PET series. Only PBT‐derived copolyesters containing a maximum of 10% alditol units showed discrete scattering characteristic of crystalline material. No substantial differences in either structure or properties were observed between the L ‐arabinitol and xylitol copolyester series. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5167–5179, 2008     

Aging and cold crystallization of melt‐extruded poly(trimethylene terephthalate) films

We analyzed the thermal crystallization, glass‐transition behavior, and mechanical properties of melt‐extruded poly(trimethylene terephthalate) (PTT) films to investigate their physical aging and annealing effects. The physical aging and annealing of PTT films had an influence on the glass‐transition temperature, recrystallization behavior, and mechanical properties. When samples were aged at an ambient temperature, the crystallization temperature decreased largely within 5 h, the heat of crystallization increased, and the breaking stress and breaking elongation increased. The glass‐transition temperature of annealed samples, which was obtained from differential scanning calorimetry and dynamic mechanical measurements, increased with increasing annealing temperature below 80 °C but decreased above that temperature. In addition, the glass‐transition temperature and modulus of annealed samples were largely affected by the annealing time; in particular, they increased sharply within 1 h on annealing at 50 °C. Consequently, the change in the glass‐transition temperature on annealing was ascribed to the fact that the molecular constraint due to recrystallization and the mobility of rigid amorphous PTT chains competed with each other, being dependent on the annealing temperature. The mechanical properties of aged samples were closely related to their cold‐crystallization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1920–1927, 2001     

Glassy polymer‐sorption phenomena measured with a quartz crystal microbalance technique

The quartz crystal microbalance (QCM) method is applied to the measurement of CO₂ sorption in glassy poly(ethylene terephthalate) (PET), poly(methyl methacrylate), and polysulfone. Polymer thin films in the thickness range of 350–550 nm are prepared by spin‐casting onto the quartz crystal devices. Sorption isotherms at temperatures below the glass transition are analyzed with the dual‐mode sorption model. As‐cast, quenched, and slow‐cooled thermal‐conditioning protocols yield consistent trends in the sorption level, namely, as‐cast > quenched > slow‐cooled. The sorption levels and model results for the quenched‐conditioned samples measured with QCM compare favorably with those reported from the pressure‐decay and gravimetric methods on thick films. With extended analysis of PET, the QCM technique is also useful for the exploration of the temperature dependence associated with gas sorption in glassy polymer systems. Measured heats of sorption and the collapse of the Langmuir component near the PET glass‐transition temperature agree with those reported previously. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2109–2118, 2003     

Poly(ethylene terephthalate) reinforced by N,N′‐diphenyl biphenyl‐3,3′,4,4′‐tetracarboxydiimide moieties

Starting with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and methyl aminobenzoate, we synthesized a novel rodlike imide‐containing monomer, N,N′‐bis[p‐(methoxy carbonyl) phenyl]‐biphenyl‐3,3′,4,4′‐tetracarboxydiimide (BMBI). The polycondensation of BMBI with dimethyl terephthalate and ethylene glycol yielded a series of copoly(ester imide)s based on the BMBI‐modified poly(ethylene terephthalate) (PET) backbone. Compared with PET, these BMBI‐modified polyesters had higher glass‐transition temperatures and higher stiffness and strength. In particular, the poly(ethylene terephthalate imide) PETI‐5, which contained 5 mol % of the imide moieties, had a glass‐transition temperature of 89.9 °C (11 °C higher than the glass‐transition temperature of PET), a tensile modulus of 869.4 MPa (20.2 % higher than that of PET), and a tensile strength of 80.8 MPa (38.8 % higher than that of PET). Therefore, a significant reinforcing effect was observed in these imide‐modified polyesters, and a new approach to higher property polyesters was suggested. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 852–863, 2002; DOI 10.1002/pola.10169     

Synthesis of high‐molecular‐weight aliphatic–aromatic copolyesters from poly(ethylene‐co‐1,6‐hexene terephthalate) and poly(L‐lactic acid) by chain extension

A series of aliphatic–aromatic multiblock copolyesters consisting of poly(ethylene‐co‐1,6‐hexene terephthalate) (PEHT) and poly(L ‐lactic acid) (PLLA) were synthesized successfully by chain‐extension reaction of dihydroxyl terminated PEHT‐OH prepolymer and dihydroxyl terminated PLLA‐OH prepolymer using toluene‐2,4‐diisoyanate as a chain extender. PEHT‐OH prepolymers were prepared by two step reactions using dimethyl terephthalate, ethylene glycol, and 1,6‐hexanediol as raw materials. PLLA‐OH prepolymers were prepared by direct polycondensation of L ‐lactic acid in the presence of 1,4‐butanediol. The chemical structures, the molecular weights and the thermal properties of PEHT‐OH, PLLA‐OH prepolymers, and PEHT‐PLLA copolymers were characterized by FTIR, ¹H NMR, GPC, TG, and DSC. This synthetic method has been proved to be very efficient for the synthesis of high‐molecular‐weight copolyesters (say, higher than M_w = 3 × 10⁵ g/mol). Only one glass transition temperature was found in the DSC curves of PEHT‐PLLA copolymers, indicating that the PLLA and PEHT segments had good miscibility. TG curves showed that all the copolyesters had good thermal stabilities. The resulting novel aromatic–aliphatic copolyesters are expected to find a potential application in the area of biodegradable polymer materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5898–5907, 2009     

Novel blue‐greenish electroluminescent poly(fluorenevinylene‐alt‐dibenzothiophenevinylene)s and their model compounds

Poly(9,9‐dihexylfluorene‐2,7‐vinylene‐alt‐dibenzothiophene‐2,8‐vinylene) (PS) and poly(9,9‐dihexylfluorene‐2,7‐vinylene‐alt‐dibenzothiophene‐5,5‐dioxide‐2,8‐ vinylene) (PSO) as well as corresponding model compounds were synthesized by Heck coupling. Both the polymers and model compounds were readily soluble in common organic solvents such as tetrahydrofuran, dichloromethane, chloroform, and toluene. The polymers showed a decomposition temperature at ～430 °C and a char yield of about 65% at 800 °C in N₂. The glass‐transition temperatures of the polymers were almost identical (75–77 °C) and higher than those of the model compounds (26–45 °C). All samples absorbed around 390 nm, and their optical band gaps were 2.69–2.85 eV. They behaved as blue‐greenish light emitting materials in both solutions and thin films, with photoluminescence emission maxima at 450–483 nm and photoluminescence quantum yields of 0.52–0.72 in solution. Organic light‐emitting diodes with an indium tin oxide/poly(ethylene dioxythiophene):poly(styrene sulfonic acid)/polymer/Mg:Ag/Ag configuration with polymers PS and PSO as emitting layers showed green electroluminescence with maxima at 530 and 540 nm, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6790–6800, 2006     

玻璃基板作用下高分子共混物薄膜相形态发展过程

研究了玻璃基板作用下极性高聚物为低组分的共混物薄膜在退火条件下相形态的发展过程 .选用聚苯乙烯 (PS) 聚甲基丙烯酸甲酯 (PMMA)与聚苯乙烯 (PS) 聚ε 己内酯 (PCL)两个体系 ,在玻璃基板上Spin Coating成膜后退火 .由于共混物薄膜中极性相对较大的高聚物组分 (PMMA和PCL)相对于极性较小的PS组分对玻璃基板具有更好的润湿性 ,所以在上述的两个共混薄膜体系中其相形态分别显示PMMA和PCL在低组分比例下最终发展成为连续相 .利用扫描电镜以及元素分析很好地验证了以上的结论 ,并且对其机理进行了解释 .此外 ,改变PS的分子量与PCL共混 ,研究了组分粘度对薄膜相形态发展的影响 .结果表明 ,PS组分粘度越大 ,共混物薄膜相结构发展速度越慢     

Synthesis and thermal behavior of new poly(ethylene terephthalate‐imide)s

Copoly(ethylene terephthalate‐imide)s (PETIs) were synthesized by the melt copolycondensation of bis(2‐hydroxyethyl)terephthalate with a new imide monomer, N,N′‐bis[p‐(2‐hydroxyethoxycarbonyl)phenyl]‐biphenyl‐3,3′,4,4′‐tetracarboxydiimide (BHEI). The copolymers were characterized by intrinsic viscosity, Fourier transform infrared, ¹H NMR, differential scanning calorimetry, and thermogravimetric analysis techniques. Although their crystallinities decreased as the content of BHEI units increased, the glass‐transition temperatures (T_g) increased significantly. When 5 or 10 mol % BHEI units were incorporated into poly(ethylene terephthalate), T_g increased by 10 or 24 °C, respectively. The thermal stabilities of PETI copolymers were about the same as the thermal stability of PET, whereas the weight loss of PETIs decreased as the content of BHEI units increased. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 408–415, 2001     

Crystallization behavior and morphology of poly(ethylene‐co‐trimethylene terephthalate)s

The melt crystallization behaviors and crystalline structures of poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate), and poly(ethylene‐co‐trimethylene terephthalate) (PETT) were investigated with differential scanning calorimetry (DSC), polarized optical microscopy (POM), and X‐ray diffraction at various crystallization temperatures (T_cs). The PETT copolymers were synthesized via the polycondensation of terephthalate with ethylene glycol and trimethylene glycol (TG) in various compositions. The copolymers with 69.0 mol % or more TG or 31.0 mol % or less TG were crystallizable, but the other copolymers containing 34–56 mol % TG were amorphous. The DSC isothermal results revealed that the addition of a small amount of flexible TG (up to 21 mol %) to the PET structure slightly reduced the formation of three‐dimensional spherulites. A greater TG concentration (91–100%) in the copolyesters changed the crystal growth from two‐dimensional to three‐dimensional. The DSC heating scans after the completion of isothermal crystallization at various T_cs showed three melting endotherms for PET, PETT‐88, PETT‐84, and PETT‐79 and four melting endotherms for PETT‐9 and PETT. The presence of an additional melting endotherm could be attributed to the melting of thinner and imperfect copolyester crystallites. Analyses of the Lauritzen–Hoffman equation demonstrated that PETT‐88 had the highest values of the product of the lateral and folding surface free energies, and this suggested that the addition of small amounts of flexible trimethylene terephthalate segments to PET disturbed chain regularity, thus increasing molecular chain mobility. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4255–4271, 2004     

Oxygen‐barrier properties of cold‐drawn polyesters

The improvement of oxygen‐barrier properties of glassy polyesters by orientation was examined. Poly(ethylene terephthalate) (PET), poly(ethylene naphthalate), and a copolymer based on PET in which 55 mol % of the terephthalate was replaced with bibenzoate (PET‐BB55) were oriented by constrained uniaxial stretching. In a fairly narrow window of stretching conditions near the glass‐transition temperature, it was possible to achieve uniform extension of the polyesters without crystallization or stress whitening. The processes of orientation and densification correlated with the conformational transformation of glycol linkages from gauche to trans. Oxygen permeability, diffusivity, and solubility decreased with the amount of orientation. A linear relationship between the oxygen solubility and polymer specific volume suggested that the cold‐drawn polyester could be regarded as a one‐phase densified glass. This allowed an analysis of oxygen solubility in accordance with free‐volume concepts of gas permeability in glassy polymers. Orientation was seen as the process of decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium (zero‐solubility) condition. Cold drawing most effectively reduced the free volume of PET‐BB55. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 862–877, 2002     

Properties and morphology of recycled poly(ethylene terephthalate)/bisphenol a polycarbonate/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) blends by low‐temperature solid‐state extrusion

Among the various methods available for recycling plastics waste, blending technology is a straightforward and relatively simple method for recycling. In this paper, a new blending technology, low‐temperature solid‐state extrusion, was discussed. Several recycled poly(terephthalate ethylene)/bisphenol a polycarbonate/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene) blends (R‐PET/PC/SEBS blends) have been prepared by this technology. The results show that thermal and hydrolytic degradation of R‐PET is improved when extruding temperature was between the glass transition temperature (T_g) and cold crystallization temperature (T_cc). Elongation at break and notched impact strength were increased evidently, from 15.9% to 103.6, and from 8.6 kJ/m² to 20.4 kJ/m², respectively. The appropriate rotating speed of screws was between 100 and 150 rpm. At the same time, the appropriate rotating speed of the screws brings a suitable shear viscosity ratio of R‐PET and PC, which is of advantage to blending of R‐PET and PC together with SEBS. Dispersion of minor phase, PC and SEBS, became finer and smaller, to about 1 µm. Chain extender, Methylenediphenyl diisocyanate (MDI) can react with the end‐carboxyl group and end‐hydroxyl group of R‐PET. FT‐IR spectra testified that the reactions have been happened in the extruding process. A chain extending reaction not only increased the molecular weight of PET and PC, but also can synthesize PET‐g‐PC copolymer to act as a reactive compatilizer. An SEM micrograph shows that a micro‐fiber structure of PET was formed in the blend sample. Copyright © 2007 John Wiley & Sons, Ltd.     

Preparation of co‐polymethyl(alkoxy)siloxanes by acid‐catalyzed controlled hydrolytic copolycondensation of methyl(trialkoxy)silane and tetraalkoxysilane

Polymethyl(alkoxy)siloxane copolymers, poly(MTES‐co‐TEOS), and poly(MTMS‐co‐TMOS), are prepared by acid‐catalyzed controlled hydrolytic co‐polycondensation of methyl(trialkoxy)silane MeSi(OR)₃ (R = Et (MTES) and Me (MTMS)) and tetra‐alkoxysilane Si(OR)₄ (R = Et (TEOS) and Me (TMOS)), respectively. The products are purified by fractional precipitation to provide polymethyl(alkoxy)siloxane copolymers with molecular weight 1000–10,000 (poly(MTES‐co‐TEOS)) or 1700–100,000 (poly(MTMS‐co‐TMOS)) that are stable to self‐condensation. These polymers are soluble in common organic solvents except for hexane, and form flexible and transparent free‐standing films with a tensile strength of 4.0–10.0 MPa. The structure of the polymethyl(alkoxy)siloxane copolymers is thought to be a random or a block co‐polymer. They are found to provide coating films with an adhesive strength up to 10, a refractive index of 1.36–1.40, and a dielectric constant of 3.5–3.6. The products also show better weathering stability than polyethoxysiloxane due to the hydrolytic polycondensation of TEOS. Field emission‐scanning electron micrography analysis reveals that coating films are composed of a micro‐phase separated structure. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4732–4741     

Poly(ethylene terephthalate) terpolyesters containing isophthalic and 5‐tert‐butylisophthalic units

Poly(ethylene terephthalate‐co‐isophthalate‐co‐5‐tert‐butylisophthalate) (PETI^tBI) terpolymers were investigated with reference to poly(ethylene terephthalate) (PET) homopolymer and poly(ethylene terephthalate‐co‐isophthalate) (PETI) copolymers. Three series of PETI^tBI terpolyesters, characterized by terephthalate contents of 90, 80, and 60 mol %, respectively, with different isophthalate/5‐tert‐butylisophthalate molar ratios, were prepared from ethylene glycol and mixtures of dimethyl terephthalate, dimethyl isophthalate, and 5‐tert‐butylisophthalic acid. The composition of the terpolymers and the composition of the feed agreed. All terpolymers had a random microstructure and number‐average molecular weights ranging from 10,000 to 20,000. The PETI^tBI terpolyesters displayed a higher glass‐transition temperature and a lower melting temperature than the PETI copolymers having the same content of terephthalic units. Thermal stability appeared essentially unchanged upon the incorporation of the 5‐tert‐butylisophthalic units. The PETI^tBIs were crystalline for terephthalate contents higher than 80 mol %, and they crystallized at lower rates than PETI. The crystal structure of the crystalline terpolymers was the same as that of PET with the 1,3‐phenylene units being excluded from the crystalline phase. Incorporation of isophthalate comonomers barely affected the tensile modulus and strength of PET, but the brittleness of the terpolymers decreased for higher contents in 5‐tert‐butylisophthalic units. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 124–134, 2003     

Synthesis of ABCD 4‐miktoarm star polymers by combination of RAFT,ROP, and “Click Chemistry”

The ABCD 4‐miktoarm star polymers based on polystyrene (PS), poly(ε‐caprolactone) (PCL), poly(methyl acrylate) (PMA), and poly(ethylene oxide) (PEO) were synthesized and characterized successfully. Using the mechanism transformation strategy, PS with three different functional groups (i.e., hydroxyl, alkyne, and trithiocarbonate), PS‐HEPPA‐SC(S)SC₁₂H₂₅, was synthesized by the reaction of the trithiocarbonate‐terminated PS with 2‐hydroxyethyl‐3‐(4‐(prop‐2‐ynyloxy)phenyl) acrylate (HEPPA) in tetrahydrofuran (THF) solution. Subsequently, the ring‐opening polymerization (ROP) of ε‐caprolactone (CL) was carried out in the presence of stannous(II) 2‐ethylhexanoate and PS‐HEPPA‐SC(S)SC₁₂H₂₅, and then the PS‐HEPPA(PCL)‐SC(S)SC₁₂H₂₅ obtained was used in reversible addition‐fragmentation chain transfer (RAFT) polymerization of methyl acrylate (MA) to produce the ABC 3‐miktoarm star polymer, S(PS)(PCL)(PMA) carrying an alkyne group. The ABCD 4‐miktoarm star polymer, S(PS)(PCL)(PMA)(PEO) was successfully prepared by click reaction of the alkyne group on the HEPPA unit with azide‐terminated PEO (PEO‐N₃). The target polymer and intermediates were characterized by NMR, FTIR, GPC, and DSC. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6641–6653, 2008     

Poly(acrylate‐b‐styrene‐b‐isobutylene‐b‐styrene‐b‐acrylate) Block Copolymers via Carbocationic and Atom Transfer Radical Polymerizations

A series of polyacrylate‐polystyrene‐polyisobutylene‐polystyrene‐polyacrylate (X‐PS‐PIB‐PS‐X) pentablock terpolymers (X=poly(methyl acrylate) (PMA), poly(butyl acrylate) (PBA), or poly(methyl methacrylate) (PMMA)) was prepared from poly (styrene‐b‐isobutylene‐b‐styrene) (PS‐PIB‐PS) block copolymers (BCPs) using either a Cu(I)Cl/1,1,4,7,7‐pentamethyldiethylenetriamine (PMDETA) or Cu(I)Cl/tris[2‐(dimethylamino)ethyl]amine (Me₆TREN) catalyst system. The PS‐PIB‐PS BCPs were prepared by quasiliving carbocationic polymerization of isobutylene using a difunctional initiator, followed by the sequential addition of styrene, and were used as macroinitiators for the atom transfer radical polymerization (ATRP) of methyl acrylate (MA), n‐butyl acrylate (BA), or methyl methacrylate (MMA). The ATRP of MA and BA proceeded in a controlled fashion using either a Cu(I)Cl/PMDETA or Cu(I)Cl/Me₆TREN catalyst system, as evidenced by a linear increase in molecular weight with conversion and low PDIs. The polymerization of MMA was less controlled. ¹H‐NMR spectroscopy was used to elucidate pentablock copolymer structure and composition. The thermal stabilities of the pentablock copolymers were slightly less than the PS‐PIB‐PS macroinitiators due to the presence of polyacrylate or polymethacrylate outer block segments. DSC analysis of the pentablock copolymers showed a plurality of glass transition temperatures, indicating a phase separated material.     

Preparation and properties of polyhedral oligomeric silsesquioxane polymers

Polyhedral oligomeric silsesquioxane (POSS) polymers were synthesized by the dehydrogenative condensation of (HSiO_3/2)₈ with water in the presence of diethylhydroxylamine followed by trimethylsilylation. Coating films were prepared by spin‐coating of the coating solution prepared by the dehydrogenative condensation of POSS. The hardness of the coating films was evaluated using a pencil‐hardness test and was found to increase up to 8H with increases in the curing temperature. Free‐standing film and silica gel powder were prepared by aging the coating solution at room temperature. The silica gel powder was subjected to heat treatment under air atmosphere to show a specific surface area of 440 m² g⁻¹ at 100 °C, which showed a maximum at 400 °C as 550 m² g⁻¹. Copyright © 2011 John Wiley & Sons, Ltd.