Electrocatalytic Oxidation and Direct Determination of L-Tyrosine by Square Wave Voltammetry at Multi-wall Carbon Nanotubes Modified Glassy Carbon Electrodes

The electrochemical behavior of L-tyrosine was investigated at a multi-wall carbon nanotubes modified glassy carbon electrode. L-tyrosine itself showed a poor electrochemical response at the bare glassy carbon electrode; however, a multi-wall carbon nanotubes film fabricated on the glassy carbon electrode can directly enhance the electrochemical signal of L-tyrosine when applying cyclic voltammetry and square wave stripping voltammetry without any mediator. Cyclic voltammetry was carried out to study the electrochemical oxidation mechanism of L-tyrosine, which shows a totally irreversible process and an oxidation potential of 671 mV at the modified electrode and 728 mV at the bare electrode, ΔE_p = 57 mV. The anodic peak current linearly increases with the square root of scan rate in the low range, suggesting that the oxidation of L-tyrosine on the multi-wall carbon nanotubes modified electrode is a diffusion-controlled process. The square wave stripping voltammetry currents of L-tyrosine at the multi-wall carbon nanotubes modified electrodes increased linearly with the concentration in the range of 2.0 × 10⁻⁶–5.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.0 × 10⁻⁷ mol L⁻¹. The method is simple, quick, sensitive and accurate.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

Voltammetric determination of N-acetylcysteine using a carbon paste electrode modified with copper(II) hexacyanoferrate(III)

The preparation and electrochemical characterization of a carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) as well as its behavior as electrocatalyst toward the oxidation of N-acetylcysteine were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of N-acetylcysteine were explored using sweep linear voltammetry. The best voltammetric response was observed for a paste composition of 20% (w/w) copper(II) hexacyanoferrate(III) complex, acetate buffer solution at pH of 6.0 as the electrolyte and scan rate of 10 mV s^− 1. A linear voltammetric response for N-acetylcysteine was obtained in the concentration range from 1.2 × 10^− 4 to 8.3 × 10^− 4 mol L^− 1, with a detection limit of 6.3 × 10^− 5 mol L^− 1. The proposed electrode is useful for the quality control and routine analysis of N-acetylcysteine in pharmaceutical formulations.     

Electrochemical behavior and voltammetric determination of tryptophan based on 4-aminobenzoic acid polymer film modified glassy carbon electrode

Herein, a novel electrochemical method was developed for the determination of tryptophan based on the poly(4-aminobenzoic acid) film modified glassy carbon electrode (GCE). The electrochemical behaviors of tryptophan at the modified electrode were investigated. It was found that the oxidation peak current of tryptophan at the modified GCE was greatly improved compared with that at the bare GCE. The effects of supporting electrolyte, pH value, scan rate, accumulation potential and time were examined. The oxidation peak current of tryptophan was proportional to its concentration over the range from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹. The limit of detection was evaluated to be 2.0 × 10⁻⁷ mol L⁻¹. The proposed method was sensitive and simple. It was successfully employed to determine tryptophan in pharmaceutical samples.     

C60 trianion-mediated electrocatalysis and amperometric sensing of hydrogen peroxide

Heterogeneous electrocatalytic reduction of hydrogen peroxide (H₂O₂) by C₆₀ is reported for the first time. C₆₀ is embedded in tetraoctylammonium bromide (TOAB) film and is characterized by scanning electron microscopy and cyclic voltammetry. Electrocatalytic studies show that the trianion of C₆₀ mediates the electrocatalytic reduction of H₂O₂ in aqueous solution containing 0.1 M KCl. Application of such film modified electrode as an amperometric sensor for H₂O₂ determination is also examined. The sensor shows a fast response within 1 s and a linear response is obtained (R = 0.9986) in the concentration range from 3.33 × 10⁻⁵ to 2.05 × 10⁻³ mol L⁻¹ for H₂O₂, with the detection limit of 2 × 10⁻⁵ mol L⁻¹ and the sensitivity of 1.65 μA mM⁻¹. A good repeatability and stability is shown for the sensor during the experiment.     

A novel poly(taurine) modified glassy carbon electrode for the simultaneous determination of epinephrine and dopamine

A novel taurine modified glassy carbon electrode was prepared by electropolymerization method. The electrochemical behaviors of epinephrine (EP) and dopamine (DA) at the modified electrode were studied by cyclic voltammetry. The modified electrode exhibited enhanced sensitivity and excellent electrochemical discrimination to DA and EP. The cathodic peaks of the two species were well-separated with a potential difference of about 390 mV, so the poly(taurine) modified electrode was used for simultaneous voltammetric measurement of EP and DA by differential pulse voltammetry. Under the optimum conditions, the cathodic peak currents were linear to concentrations of EP and DA in the range of 2.0 × 10⁻⁶ to 6.0 × 10⁻⁴ mol L⁻¹ and 1.0 × 10⁻⁶ to 8.0 × 10⁻⁴ mol L⁻¹, respectively. The detection limits for EP and DA were 3.0 × 10⁻⁷ and 1.0 × 10⁻⁷ mol L⁻¹, respectively. Because the oxidation of ascorbic acid (AA) is an irreversible reaction at modified electrode, the interference of AA for determining EP and DA was eliminated. The modified electrode has been satisfactorily used for the simultaneous determination of EP and DA in pharmaceutical injections.     

Electrochemical Characterization of Pyrocatechol Sulfonephthalein-Modified Glassy Carbon Electrode and Separation of Electrocatalytic Responses for Ascorbic Acid and Dopamine Oxidation

A pyrocatechol sulfonephthalein- (PS-) modified glassy carbon (PS/GC) electrode has been prepared by adsorption of PS on a glassy carbon electrode surface. Cyclic voltammograms of the PS/GC electrode indicate the presence of a couple of well-defined redox peaks, and the formal potential shifts in the negative direction with increasing solution pH. The relation between formal potential,E^0′, and solution pH can be fit to the equationE^0′(mV) = −51.4 pH + 538.7. The PS/GC electrode shows high electrocatalytic activity toward ascorbic acid oxidation, with an overpotential ca. 380 mV less than that of the bare electrode and a drastic enhancement of the anodic currents. The electrocatalytic reaction rate constant (k), which was decreased with increasing concentration of H₂A, was determined using rotating disk electrode measurements. The values ofkwas also affected by the solution pH. The electrode can also separate the electrochemical responses of ascorbic acid and dopamine. The separation between the anodic peak potentials of ascorbic acid and dopamine is more than 50 mV by the differential pulse voltammetry.     

Immobilization of ABTS – laccase system in silicate based electrode for biolectrocatalytic reduction of dioxygen

Voltametrically stable 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonate) (ABTS²⁻) modified electrode was obtained by sol–gel processing of methyltrimethoxysilane based sol with dissolved ABTS²⁻ together with dispersed graphite particles. Next, extracellular laccase from Cerrena unicolor was encapsulated within a thin hydrophilic tetramethoxysilane film on the top the electrode. The obtained ABTS²⁻ modified carbon ceramic electrode exhibits stable voltammetry corresponding to the surface confined oxidation reduction process. The biocatalytic activity of this electrode is similar to that observed when ABTS²⁻ is present in solution.     

Palladized aluminum electrode covered by Prussian blue film as an effective transducer for electrocatalytic oxidation and hydrodynamic amperometry of N-acetyl-cysteine and glutathione

The mediated oxidation of N-acetyl cysteine (NAC) and glutathione (GL) at the palladized aluminum electrode modified by Prussian blue film (PB/Pd–Al) is described. The catalytic activity of PB/Pd–Al was explored in terms of Fe^III[Fe^III(CN)₆]/Fe^III[Fe^II(CN)₆]¹⁻ system by taking advantage of the metallic palladium layer inserted between PB film and Al, as an electron-transfer bridge. The best mediated oxidation of NAC and GL on the PB/Pd–Al electrode was achieved in 0.5 M KNO₃ + 0.2 M potassium acetate of pH 2. The mechanism and kinetics of the catalytic oxidation reactions of the both compounds were monitored by cyclic voltammetry and chronoamperometry. The charge transfer-rate limiting step as well as overall oxidation reaction of NAC or GL is found to be a one-electron abstraction. The values of transfer coefficients α, catalytic rate constant k and diffusion coefficient D are 0.5, 3.2 × 10² M⁻¹ s⁻¹ and 2.45 × 10⁻⁵ cm² s⁻¹ for NAC and 0.5, 2.1 × 10² M⁻¹ s⁻¹ and 3.7 × 10⁻⁵ cm² s⁻¹ for GL, respectively. The modifying layers on the Pd–Al substrate have reproducible behavior and a high level of stability in the electrolyte solutions. The modified electrode is exploited for hydrodynamic amperometry of NAC and GL. The amperometric calibration graph is linear in concentration ranges 2 × 10⁻⁶–40 × 10⁻⁶ for NAC and 5 × 10⁻⁷–18 × 10⁻⁶ M for GL and the detection limits are 5.4 × 10⁻⁷ and 4.6 × 10⁻⁷ M, respectively.     

A new hydrogen peroxide biosensor based on gold nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film-modified electrode

Gold nanoelectrode ensembles were produced by electrodeposition using multiwalled carbon nanotubes (MWNTs) as template. A new third generation amperometric biosensor for hydrogen peroxide was developed based on adsorption of horseradish peroxidase (HRP) at the glassy carbon (GC) electrode modified with Au nanoelectrode ensembles/multiwalled carbon nanotubes/chitosan film. The resulting HRP biosensor offered an excellent detection for hydrogen peroxide at −0.11 V with a linear response range of 2.08 × 10⁻⁷ to 7.6 × 10⁻³ M with a correlation coefficient of 0.998, and response time <5 s. The detection limit was 1.02 × 10⁻⁷ M at 3σ. The biosensor displays rapid response, expanded linear response range, and excellent repeatability. The simple and fast fabrication of the sensor makes it superior to other techniques.     

Fabrication of a template-synthesized gold nanorod-modified electrode for the detection of dopamine in the presence of ascorbic acid

Gold nanorods (GNRs) with suitable aspect ratio were synthesized with a template technique and then dispersed in a saturated sodium citrate solution by ultrasonication to form a GNR suspension. A GNR-modified electrode was fabricated using the GNR suspension. The oxidation of dopamine at the GNR/GC electrode exhibited surprisingly high electrocatalytic activity and adsorption-controlled characteristics. Square-wave voltammetry was used to detect dopamine. At the GNR/GC electrode, the linear concentration range of DA is from 1 × 10⁻⁸ M to 1 × 10⁻⁷ M and the detection limit (s/n = 3) is as low as 5.5 × 10⁻⁹ M. The current sensitivity is 3.280 μA/μM, and 1000-fold ascorbic acid (AA) cannot interfere with the determination of DA. All these performances are greatly superior to those of the bare GC electrode.     

CO electrooxidation on a polycrystalline Pt electrode: A wall-jet EQCN study

Pre-adsorbed and bulk (continuous) CO oxidation on a polycrystalline Pt electrode were examined in a wall-jet electrochemical quartz crystal nanobalance (EQCN) setup, using both differential and integral evaluation of the EQCN data, to get further insights into the kinetics and mechanism of this important fuel-cell related electrocatalytic reaction. The hydrogen underpotential adsorption–desorption features in the base cyclic voltammogram of a Pt film are accompanied by significant changes in the electrode mass due H-upd induced desorption–adsorption of anion. In the double-layer region small capacitive currents are accompanied by comparatively large reversible mass changes indicating anion adsorption/desorption (96.5 g mol⁻¹ assigned to bisulfate). OH and oxygen electrosorption from water at potentials more positive of 1.0 V result in relatively small variations in the electrode mass (16 g mol⁻¹ for PtOH and ca. 9 g mol⁻¹ for PtO formation, respectively). The CO-adlayer stripping first leads to the electrode mass decrease in the “pre-peak” region, followed by a fast mass increase within the main stripping peak due to re-adsorption of bisulfate anion (91 g mol⁻¹). A mass-transport limited current for bulk CO oxidation under continuous flow of CO-saturated electrolyte leads to negligible mass changes (0–1 g mol⁻¹) in the PtO region, suggesting that bulk CO oxidation is mediated by electroformed PtO.     

Electrochemistry and electrocatalytic activity of catechin film on a glassy carbon electrode toward the oxidation of hydrazine

A very stable electroactive film of catechin was electrochemically deposited on the surface of activated glassy carbon electrode. The electrochemical behavior of catechin modified glassy carbon electrode (CMGCE) was extensively studied using cyclic voltammetry. The properties of the electrodeposited films, during preparation under different conditions, and the stability of the deposited film were examined. The charge transfer coefficient (α) and charge transfer rate constant (k _s) for catechin deposited film were calculated. It was found that the modified electrode exhibited excellent electrocatalytic activity toward hydrazine oxidation and it also showed a very large decrease in the overpotential for the oxidation of hydrazine. The CMGCE was employed to study electrocatalytic oxidation of hydrazine using cyclic voltammetry, rotating disk voltammetry, chronoamperometry, amperometry and square-wave voltammetry as diagnostic techniques. The catalytic rate constant of the modified electrode for the oxidation of hydrazine was determined by cyclic voltammetry, chronoamperometry and rotating disk voltammetry and was found to be around 10⁻³ cm s⁻¹ . In the used different voltammetric methods, the plot of the electrocatalytic current versus hydrazine concentration is constituted of two linear segments with different ranges of hydrazine concentration. Furthermore, amperometry in stirred solution exhibits a detection limit of 0.165 μM and the precision of 4.7% for replicate measurements of 40.0 μM solution of hydrazine.     

Electrocatalytic oxidation of NADH at single-wall carbon-nanotube-paste electrodes: kinetic considerations for use of a redox mediator in solution and dissolved in the paste

Cyclic voltammetry has been successfully used to study the oxidation of nicotinamide adenine dinucleotide (NADH) at single-wall carbon-nanotube-paste (CNTP) electrodes modified with p-methylaminophenolsulfate (p-MAP) and 3,4-dihydroxybenzaldehyde (3,4-DHB). Diffusion-like behaviour was observed for p-MAP-modified electrodes, and a diffusion coefficient of 2.4×10^–6 cm² s^–1 was calculated for p-MAP in the paste. The behaviour of 3,4-DHB-modified CNTP electrodes was typical of that of surface-confined mediators. p-MAP electrocatalytic activity was first checked in solution, and a rate constant of 9.2 mol^–1 L s^–1 was obtained for the reaction between NADH and the mediator. The p-MAP-modified electrode did not have significant electrocatalytic activity for electro-oxidation of NADH, probably because of the formation of a complex between NADH and the confined mediator. In contrast, the 3,4-DHB-modified electrode had very good NADH electrocatalytic activity, with a heterogeneous rate constant of approximately 20×10² mol^–1 L s^–1.     

Direct electrochemistry and spectroelectrochemistry of osmium substituted horseradish peroxidase

In this contribution the substitution of the central protoporphyrin IX iron complex of horseradish peroxidase by the respective osmium porphyrin complex is described. The direct electrochemical reduction of the Os containing horseradish peroxidase (OsHRP) was achieved at ITO and modified glassy carbon electrodes and in combination with spectroscopy revealed the three redox couples Os^IIIHRP/Os^IVHRP, Os^IVHRP/Os^VHRP and Os^VHRP/Os^VIHRP. The midpoint potentials differ dependent on the electrode material used with E_1/2 (Os^III/IV) of − 0.4 V (ITO) and − 0.25 V (GC), E_1/2 (Os^IV/^V) of − 0.16 V (ITO) and + 0.10 V (GC), and E_1/2 (Os^V/VI)of + 0.18 V (ITO), respectively. Moreover, with immobilised OsHRP the direct electrocatalytic reduction of hydrogen peroxide and tert-butyl hydroperoxide was observed. In comparison to electrodes modified with native HRP the sensitivity of the OsHRP-electrode for tert-butyl hydroperoxide is higher.     

Voltammetry of a Benzoquinone–Hydroquinone Redox Couple at Electrodes Modified with a Polyvinylpyridine Film Doped with Cobalt Phthalocyanine

The electrochemical properties of a glassy-carbon electrode coated with a polyvinylpyridine film doped with incorporated cobalt phthalocyanine were studied in a reaction involving a benzoquinone–hydroquinone redox couple. It was found that poly-(2-vinylpyridine) film applied to the electrode and cobalt phthalocyanine deposited onto it or incorporated in the polymeric film exhibited electrocatalytic activity on the oxidation of hydroquinone. Conditions were selected for obtaining a polyvinylpyridine film doped with cobalt phthalocyanine on the electrode surface providing a maximum catalytic effect. The current of the hydroquinone oxidation peak and the current of the reverse benzoquinone reduction peak at the chemically modified electrode were linear functions of their concentrations in the range from 1 × 10^–6 to 1 × 10^–3 M.     

Electrochemical sensor of nitrite based on an inorganic film modified glassy carbon electrode

The electrocatalysis of nitrite in solutions at an inorganic film modified glassy carbon electrode was studied. The modifier was an electrodeposited thin inorganic film of the copper-heptacyanonitrosylferrate (CuHNF). Cyclic voltammetry of the modified electrode in a nitrite solution revealed that both oxidation and reduction of nitrite were catalyzed and the electrocatalytic currents were controlled by the diffusion of nitrite. Voltammetric and amperometric responses were investigated. When applied as an amperometric sensor in a flow injection system, the modified electrode permitted detection at — 0.55 V, over 500 mV lower than at the naked electrode surface. A linear response range extending from 1 × 10^–6 to 1 × 10^–3 M nitrite was obtained, with a detection limit of 3 × 10^–7 M. The relative standard deviation for 50 repetitive injections with a 5 × 10^–5 M nitrite solution was less than 4%. The procedure was applied to the determination of nitrite in saliva and nitrate.     

Simultaneous determination of hydroquinone and catechol at PASA/MWNTs composite film modified glassy carbon electrode

A poly-amidosulfonic acid and multi-wall carbon nanotubes composite (PASA/MWNTs) modified electrode has been constructed by electropolymerization on glassy carbon electrode (GCE). The electrochemical behaviors of hydroquinone (HQ) and catechol (CC) were investigated using cyclic and differential pulse voltammetries (DPVs) at the prepared electrode. Separation of the reductive peak potentials for HQ and CC was about 120 mV in pH 6.0 phosphate buffer solution (PBS), which makes it suitable for simultaneous determination of these compounds. In the presence of 1.0 × 10⁻⁴ mol L⁻¹ isomer, the reductive peak currents of DPV are proportional to the concentration of HQ in the range of 6.0 × 10⁻⁶ to 4.0 × 10⁻⁴ mol L⁻¹, and to that of CC in the range of 6.0 × 10⁻⁶ to 7.0 × 10⁻⁴ mol L⁻¹. When simultaneously changing the concentration of both HQ and CC, the linear concentration range of HQ (or CC) is 6.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ (or 6.0 × 10⁻⁶ to 1.8 × 10⁻⁴ mol L⁻¹), and the corresponding detection limits are 1.0 × 10⁻⁶ mol L⁻¹. The proposed method has been applied to simultaneous determination of HQ and catechol in water sample, and the results are satisfactory.     

Direct electrochemistry of glucose oxidase based on its direct immobilization on carbon ionic liquid electrode and glucose sensing

Direct electrochemistry of glucose oxidase (GOx) has been achieved by its direct immobilization on carbon ionic liquid electrode (CILE) with a conductive hydrophobic ionic liquid, 1-butyl pyridinium hexafluophosphate ([BuPy][PF₆]) as binder for the first time. A pair of reversible peaks is exhibited on GOx/CILE by cyclic voltammetry. The peak-to-peak potential separation (ΔE_P) of immobilized GOx is 0.056 V in 0.067 M phosphate buffer solution (pH 6.98) with scan rate of 0.1 V/s. The average surface coverage and the apparent Michaelis–Menten constant are 6.69 × 10⁻¹¹ mol·cm⁻² and 2.47 μM. GOx/CILE shows excellent electrocatalytic activity towards glucose determination in the range of 0.1–800 μM with detection limit of 0.03 μM (S/N = 3). The biosensor has been successfully applied to the determination of glucose in human plasma with the average recoveries between 95.0% and 102.5% for three times determination. The direct electrochemistry of GOx on CILE is achieved without the help of any supporting film or any electron mediator. GOx/CILE is inexpensive, stable, repeatable and easy to be fabricated.     

Electrocatalytic oxidation of quinine sulfate at a multiwall carbon nanotubes-ionic liquid modified glassy carbon electrode and its electrochemical determination

The electrocatalytic oxidation of quinine sulfate (QS) was investigated at a glassy carbon electrode, modified by a gel containing multiwall carbon nanotubes (MWCNTs) and room-temperature ionic liquid of 1-Butyl-3-methylimidazolium hexafluorophate (BMIMPF₆) in 0.10 M of phosphate buffer solution (PBS, pH 6.8). It was found that an irreversible anodic oxidation peak of QS with E _pa as 0.99 V appeared at MWCNTs-RTIL/glassy carbon electrode (GCE). The electrode reaction process was a diffusion-controlled one and the electrochemical oxidation involved two electrons transferring and two protons participation. Furthermore, the charge-transfer coefficient (α), diffusion coefficient (D), and electrode reaction rate constant (k _f) of QS were found to be 0.87, 7.89 × 10⁻³ cm²⋅s⁻¹ and 3.43 × 10⁻² s⁻¹, respectively. Under optimized conditions, linear calibration curves were obtained over the QS concentration range 3.0 × 10⁻⁶ to 1.0 × 10⁻⁴ M by square wave voltammetry, and the detection limit was found to be 0.44 μM based on the signal-to-noise ratio of 3. In addition, the novel MWCNTs-RTIL/GCE was characterized by the electrochemical impedance spectroscopy and the proposed method has been successfully applied in the electrochemical quantitative determination of quinine content in commercial injection samples and the determination results could meet the requirement.