3D FT-IR imaging spectroscopy of phase-separation in a poly(3-hydroxybutyrate)/poly(l-lactic acid) blend

In the present study, 3D FT-IR spectroscopic imaging measurements were applied to study the phase separation of a poly(3-hydroxybutyrate) (PHB)/poly(l-lactic acid) (PLA) (50:50 wt.%) polymer blend film. While in 2D projection imaging the z-dependent information is overlapped, thereby complicating the analysis, FT-IR spectro-micro-tomography, obtained from computed tomographic back projection calculations, results in distinct 3D chemical images that provide detailed information of phase separation of the two polymer components that are well separated.     

Transparent and ductile poly(lactic acid)/poly(butyl acrylate) (PBA) blends: Structure and properties

Poly(butyl acrylate) was prepared by the free radical polymerization of butyl acrylate as an initiator in the presence of 2,2′-Azoisobu-tyronitrile (AIBN) and the average molecular weight, polydispersity and thermal stability were evaluated. PLA and PBA were melt blended using a Haake Rheometer, and the light transmission, thermal properties, dynamic rheological properties, mechanical properties, phase morphology of blends and toughening mechanism were investigated. Dynamic rheology, SEM and DSC results show that the PLA is partial miscible with PBA. The PBA component improved the crystallization ability of PLA and the crystallinity of PLA increased with content of PBA (<15 wt.%). With the increase of PBA, the tensile strength and modulus of the blend decreased slightly while the elongation at break and toughness were dramatically increased. With the addition of PBA, the failure mode changes from brittle fracture of neat PLA to ductile fracture of the blend. Rheological results revealed the complex viscosity and melt elasticity of the blends decreased with increasing content of PBA and phase segregation occurred at loading above 11 wt.% PBA. UV–vis light transmittance showed that PLA/PBA blends with a high transparency, and the transmittance decreased with the amount of PBA.     

Radiolytic stabilization of poly(hydroxybutyrate)

Stabilization against gamma irradiation effects on Brazilian poly(hydroxybutyrate) (PHB) films was investigated by using commercial additives. With the most effective additive the G value of main chain scissions decreased from 8.6 to 1.5 scissions/100 eV in the absorbed dose range up to 35 kGy. Irradiation increased the biodegradability of the samples, whereas the additives-induced reduction in biodegradability. Irradiation treatment did not influence the degree of crystallinity. Protonic nuclear magnetic resonance (NMR-¹H) analysis revealed formation of hydroxyl-terminal groups upon irradiation.     

Structural evolution of poly(lactic acid) upon uniaxial stretching investigated by in situ infrared spectroscopy

Structural evolution of poly(lactic acid) (PLA) upon uniaxial stretching was studied with in-situ polarized infrared spectroscopy measurements, and its structural change affected by annealing was also investigated. Band shifting was used to reflect the structural ordering process. It was found that the band at 1302 cm⁻¹ always moves to low wavenumbers before crystallization, indicating the occurrence of intermolecular packing ordering. However, the band at 869 cm⁻¹ shifts to high wavenumbers, which is related to the transition from the amorphous phase to the ordered phase. Interestingly, during stretching, the shifting for the band at 1302 cm⁻¹ always occurs before that for the lower wavenumber band, whereas these two band shifts take place simultaneously under annealing. Based on the different characteristics of the structural evolution under stretching and annealing processes, a critical temperature was found at around 63 °C, which influences the effect weight of kinetic and thermodynamic factors to the crystallization behavior. The effect of the drawing temperature on crystallization and mechanical property of PLA films was also analyzed.     

Preparation and characterization of microspheres based on blend of poly(lactic acid) and poly(ɛ-caprolactone) with poly(vinyl alcohol) as emulsifier

In this paper, microspheres were prepared by oil-in-water (o/w) emulsion solvent evaporation method. Biodegradable polymer such as blend of poly (lactic acid) (PLA) and poly(?-caprolactone) (PCL) with certain compositions and characteristics was used to prepare the microspheres with poly(vinyl alcohol) (PVA) as an emulsifier. This study observed the microspheres particle’s size distribution at various concentrations of PVA (1%, 1.5%, 2%, and 2.5% PVA). The PVA volume variations effects during the process (50, 100, 150, 200, and 250 mL) were also observed. The blend of PLA and PCL is formed only by physical interaction between them. This can be seen from the FTIR spectrum which shows both PLA and PCL component. The microspheres physical size and appearance were observed by optical microscope (MO). The overall results of this study showed that the formula which used 50–150 mL of 2.5% polyvinyl alcohol produced the microspheres with the most uniform size distribution.     

Uniaxial drawing of poly[(R)-3-hydroxybutyrate]/cellulose acetate butyrate blends and their orientation behavior

Miscible blends of PHB and CAB were prepared by the solvent-casting method with various blend compositions, and their orientation behavior was investigated during uniaxial drawing. X-ray analysis revealed that the orientation of the crystallizable PHB component in the drawn PHB/CAB blends was changed from c-axis-orientation to a-axis-orientation with increasing CAB content. The a-axis-orientation was a result from the a-axis-oriented crystal growth caused by the intramolecular nucleation and the confined crystal growth. For quantitative assessment of the chain orientation, the Hermans orientation functions of the two respective components were obtained from the polarized FT-IR measurements. The orientation function of pure PHB stretched to 5 times of its initial length was approximately 0.8. However the value decreased rapidly with increasing CAB content, and it turned to a negative value from 30 wt.-% CAB content. This indicates that the PHB chains were aligned perpendicular to the drawing direction. On the contrary, the value of the CAB component remained almost unchanged at about 0.1 regardless of the blend composition and the annealing time, indicating that the CAB chains were constantly oriented parallel to the drawing direction without any chain relaxation. In addition, SAXS analysis suggested that the lamellar stacking direction also changed from parallel to perpendicular in the stretching direction with increasing CAB content.     

Novel miscible blends of poly(p-dioxanone) with poly(vinyl phenol)

Poly(p-dioxanone) (PPDO) has been blended with poly(vinyl phenol) (PVPh) and the PPDO/PVPh blends have been investigated using DSC, FTIR and POM. According to the single T_g criterion, miscibility has been found in the whole composition range for the blends obtained by solvent casting from dioxane solutions. The dependence of the T_g on composition shows negative deviation from the Fox equation. The interaction parameter, obtained from melting point depression analysis, χ₁₂ = ?1.0, confirms a thermodynamically miscible blend. Specific interactions have been analyzed by FTIR. The OH stretching region of PVPh indicates that upon addition of PPDO the hydroxyl–hydroxyl autoassociation interactions are mainly replaced by hydroxyl–carbonyl interassociation contacts, in detrimental of the possible hydroxyl–ether interactions. The carbonyl stretching region of pure PPDO is sensitive to intramolecular ether-ester interactions occurring in the oxyethanoate structures (–O–CH₂–CO–O–) present along the PPDO chain. The –O–CH₂–CO–O– structure presents only two minimum energy conformations, trans and cis, resulting in two different absorptions in the CO stretching region located respectively at about 1757 and 1732 cm^?1. Blending with PVPh promotes two new contributions red shifted by about 23 cm^?1 relative to the “free” CO components. Finally, POM analysis shows that the addition of PVPh to PPDO significantly decreases the crystallization rate of PPDO.     

Poly(ether amine) and cross-linked poly(propylene oxide) diacrylate thin-film polymer electrolyte for 3D-microbatteries

This paper presents a novel thin-film electrolyte of a 2:1 blend of polyetheramine (glyceryl poly(oxypropylene)) and cross-linked oligomeric poly(propylene oxide) diacrylate with LiTFSI. The polyetheramine acts as a surfactant, and can thereby be applied as a conformal coating on complex surfaces—here demonstrated for porous LiFePO₄ cathodes—making it useful for 3D-microbatteries. The poly(propylene oxide) diacrylate blends with the surfactant and is easily UV cross-linked, thereby ensuring good mechanical stability. Electrolytes, ~ 2 μm thick, were casted onto LiFePO₄ cathodes and cycled against metallic lithium, displaying stable discharge capacities of ~ 8 mAh/g at room temperature and ~ 120 mAh/g at 60 °C. The electrolyte showed conductivities of 3.45 × 10^? 6 and 5.80 × 10^? 5 S cm^? 1 at room temperature and 60 °C, respectively.     

PDMS migration at poly(vinyl chloride)/poly(ɛ-caprolactone)/poly(ɛ-caprolactone)-b-poly(dimethylsiloxane) blends surfaces

Films composed of poly(vinyl chloride)/poly(?-caprolactone)/poly(?-caprolactone)-b-poly(dimethylsiloxane) [PVC/PCL/(PCL-b-PDMS)] blends were prepared by solvent casting from tetrahydrofuran. The PVC content was kept constant (60 wt %) while varying the PCL and PCL-b-PDMS contents, part of the PCL (0–20 wt %) in the PVC/PCL (60/40) blend being replaced with PCL-b-PDMS with different molecular weights of the PCL blocks. The prepared blends were investigated by infrared spectroscopy and contact angle measurements. FTIR analysis and contact angle measurements indicate that the PDMS blocks tend to migrate towards the surface and this migration is preferential to the side in contact with air.     

Preparation of poly(ether ether ketone)-based polymer electrolytes for fuel cell membranes using grafting technique

Poly(ether ether ketone) (PEEK)-based polymer electrolyte membranes (PEMs) was successfully prepared by radiation grafting of a styrene monomer into PEEK films and the consequent selective sulfonation of the grafting chains in the film state. Using milder sulfonation, the sulfonation reactions proceeded at the grafted chains in preference to the phenylene rings of PEEK main chains; as a result, the grafted films could successfully transform to a PEM with conductivity of more than 0.1 S/cm. The ion exchange capacity (IEC) and conductivity of the grafted PEEK electrolyte membranes were controlled to the ranges of 1.2–2.9 mmol/g and 0.03–0.18 S/cm by changing the grafting degree. It should be noted that this is the first example of directly transforming super-engineering plastic films into a PEM using radiation grafting.     

Structure and morphology optimization of poly(3-hexylthiophene) thin films onto silanized silicon oxide

The influence of the preparation conditions, including substrate functionalization with common silanizers, onto structure/morphology of the overlying poly(3-hexylthiophene) thin films has been investigated by using both grazing incidence X-ray diffraction and atomic force microscopy. The factors determining the formation of spin-coated films suitable for applications in field effect transistors, i.e. concentration, spin-speed, and thermal treatment are addressed. We have established, by a tuning of the preparation and post-deposition treatments, the optimal conditions to get films with the required structural/morphologic features. Moreover we have shown that the macromolecules orient and organize at the interface zone (?10 nm from the interface) better than in the upper layers, i.e. far away from the interface.     

Physicochemical investigation of the clouding behavior and thermodynamics of p-tert-alkylphenoxy poly (oxyethylene) ether micelles in aqueous environment and in the presence of diols

Cloud point (CP) measurements of nonionic surfactant namely p-tert-alkylphenoxy poly (oxyethylene) ether (TX-100) were carried out in the absence and presence of organic additives such as diols (1,2-ethanediol; 1,2-propanediol and 2,3-butanediol) and polyols (glycerol, glucose, fructose and sorbitol). For (diol + TX-100 + water) system, cloud points (CP) were found to be increased with the increase in concentration of diols for both (4 and 10)% TX-100 solutions and found to follow the order: CP_{1,2-propanediol} > CP_{2,3-butanediol} > CP_{1,2-ethanediol}. For (polyols + TX-100 + water) system, the depression of cloud point (CP) was observed with increase of polyol concentrations for both (4 and 10)% of TX-100 solutions and the trend almost follows the order: CP_glycerol < CP_glucose < CP_fructose < CP_sorbitol. The values of $\mathrm{\Delta }{G}_{\text{c}}°$ were found to be positive for all the systems studied. The $\mathrm{\Delta }{H}_{\text{c}}°$ and $\mathrm{\Delta }{S}_{\text{c}}°$ values were found to be positive in the presence of diols while those were found to be almost negative in the presence of polyols during clouding of TX-100.     

Caractérisation par spectrométrie de masse MALDI–TOF de poly(isosorbide-éther)s cycliques et linéaires obtenus sous irradiation microondes

Characterisation of cyclic and linear poly(isosorbide-ether)s obtained under microwave irradiation by MALDI–TOF mass spectrometry. We studied the influence of the alkyl chain length and of the leaving group on the fraction of cyclic or linear poly(isosorbide-ether)s. A survey by MALDI–TOF MS showed that cyclic chains (C) are predominant when some short aliphatic chains are used (m = 4 or 6), whereas with longer chains (m = 8, 10 or 12), we noted that cyclic products were in a minority, whatever the leaving group (bromide or mesyl). Important non-thermal microwave effects have been demonstrated, notably a methanol-insoluble fraction of polyether considerably larger than the one obtained by conventional heating. These poly(isosorbide-ether)s have been characterized by RMN, MALDI–TOF, SEC, elementary analysis, and DSC. The survey of the thermal behaviour by DSC showed that the temperatures of fusion increase with the aliphatic chain's length (m = 12; T_f = 37 °C).     

Phase separation in aqueous two-phase systems containing poly(ethylene glycol) and magnesium sulphate at different temperatures

New experimental (liquid + liquid) equilibrium data have been determined for aqueous systems containing poly(ethylene glycol) of nominal molar mass 10,000 and magnesium sulphate at T = (295.15, 301.15, 305.15, and 311.15) K. The effect of temperature on the liquid compositions of coexisting phases is discussed. The experimental (liquid + liquid) equilibrium data of the systems were correlated by non-random two-liquid (NRTL) activity coefficient model. The interaction parameters of the NRTL activity coefficient model are obtained and reported. The calculated root mean square deviations (RMSD) showed that NRTL activity coefficient model can be used satisfactorily to correlate the (liquid + liquid) equilibrium data in aqueous solution of the {poly(ethylene glycol) + magnesium sulphate} system.     

Evaluation of Schiff bases of 2,5-dimercapto-1,3,4-thiadiazole as photostabilizer for poly(methyl methacrylate)

The photostabilization of poly(methyl methacrylate) (PMMA) films by Schiff bases of 2,5-dimercapto-1,3,4-thiadiazole compounds was investigated. The PMMA films containing concentration of complexes 0.5% by weight were produced by the casting method from chloroform solvent. The photostabilization activities of these compounds were determined by monitoring the hydroxyl index with irradiation time. The changes in viscosity average molecular weight of PMMA with irradiation time were also tracked (using benzene as a solvent). The quantum yield of the chain scission (Φ_cs) of these complexes in PMMA films was evaluated and found to range between 4.19 × 10^?5 and 8.75 × 10^?5. Results obtained showed that the rate of photostabilization of PMMA in the presence of the additive followed the trend:[1] > [2] > [3] > [4] > [5].According to the experimental results obtained, several mechanisms were suggested depending on the structure of the additive. Among them, UV absorption, peroxide decomposer, and radical scavenger for photostabilizer mechanisms were suggested.     

Synthesis and characterization of photocrosslinkable poly(l-lactide)s with a pendent cinnamate group

In this report, we describe the synthesis and characterization of photosensitive poly(l-lactide) with a pendent cinnamate group. α,ω-Dihydoxy terminated poly(l-lactide) (PLLA-diol) [molecular weights (MW); 2000, 4000 and 9000 g/mol ] was chain-extended with a diacyl chloride of 5-cinnamoyloxyisophthalic acid (ICA) to obtain high-molecular-weight photocrosslinkable poly(l-lactide)s (ICA/PLLA). The resulting polyesters were characterized by proton nuclear magnetic resonance spectroscopy, gel permeation chromatography, ultraviolet–visible spectroscopy, differential scanning calorimetry, thermomechanical analysis and thermogravimetry. The glass transition temperature (T_g), the melting temperature (T_m) and the degree of relative crystallinity (X_c) of ICA/PLLAs increased with the increasing MW of the PLLA-diols. The photosensitive ICA/PLLAs were irradiated with a 400 W high-pressure mercury lamp (λ > 280 nm) for various times to produce the PLLA gel films without a photoinitiator. The crosslinking rate monitored by a UV–vis spectrum decreased with the increasing MW of the PLLA-diols. The crosslinking of the ICA/PLLA ?4000 film enhanced the T_g slightly and the tensile strength and Young’s modulus significantly, while reduced the T_m and X_c. The enzymatic degradation was measured by the weight loss of the films in a phosphate buffer solution with proteinaze-k. The crosslinking of the films decreased markedly the degradation rate.     

Gas permeation properties of poly(lactic acid)

The need for the development of polymeric materials based on renewable resources has led to the development of poly(lactic acid) (PLA) which is being produced from a feedstock of corn rather than petroleum. The present study examines the permeation of nitrogen, oxygen, carbon dioxide, and methane in amorphous films of PLA cast from solution. The properties of PLA are compared to other commodity plastics and it is shown that PLA permeation closely resembles that of polystyrene. At 30°C, N₂ permeation in PLA is 1.3 (10⁻¹⁰ cm³ (STP) cm/cm² s cmHg) and the activation energy is 11.2 kJ/mol. For oxygen the corresponding values are 3.3 (10⁻¹⁰ cm³(STP) cm/cm² s cm Hg) and 11.1 kJ/mol. The values for carbon dioxide permeation are 1.2 (10⁻¹⁰ cm³ (STP) cm/cm² s cmHg) and 6.1 kJ/mol. For methane values of 1.0 (10⁻¹⁰ cm³ (STP) cm/cm² s cmHg) and an activation energy of 13.0 kJ/mol are found. Studies with pure gases show that polymer chain branching and small changes in l:d stereochemical content have no effect on permeation properties. Crystallinity is found to dominate permeation properties in a biaxially oriented film. The separation factor for a CO₂/CH₄ mixed gas system is measured between 0 and 50°C and does not deviate significantly from the calculated ideal separation factor; at 0°C the separation factor is 16, a value that suggests continued studies of PLA as a separation medium are warranted.     

Strong electric fields promote oriented intercalative polymerization of pyrrole inside the lamellar matrices of vanadium pentoxide

The effect of strong electric fields (e.g., 3.4 kV/m) in the 1 1 0 plane direction, in the conductivity of the V₂O₅·nH₂O xerogel (also known as VXG) and in the intercalative redox polymerization of pyrrole in the VXG matrices has been investigated. The resulting poly(pyrrole) nanocomposites exhibited electric anisotropy in the 1 0 0 and 0 1 0 crystallographic directions. Photomicrographies of such materials revealed that the polymer fibers tend to orient themselves along the applied field.     

Radiation-induced grafting of styrene into poly(vinylidene fluoride) film by simultaneous method with two different solvents

Radiation-induced grafting of styrene into poly(vinylidene fluoride) (PVDF) films with 0.125 mm thickness at doses of 1 and 2.5 kGy in the presence of a styrene/N,N-dimethylformamide (DMF) solution (1:1, v/v) and at doses of 20, 40 and 80 kGy in presence of a styrene/toluene solution (1:1, v/v) at dose rate of 5 kGy h^?1 was carried out by the simultaneous method under nitrogen atmosphere and room temperature, using gamma rays from a Co-60. The films were characterized before and after modification by calculated grafting yield (GY %), infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetry (TG/DTG). GY results shows that grafting increases with dose, and the grafting of styrene was confirm by FT-IR due to the new characteristic peaks and by the TG and DSC attributed to changes in thermal behavior of the grafted material. Results showed that the system allows the controlled grafting of styrene into PVDF using gamma rays at doses as low as 1 kGy in DMF.