Synthesis and characterization of aromatic poly(ether sulfone imide)s derived from sulfonyl bis(ether anhydride)s and aromatic diamines

Two sulfonyl group-containing bis(ether anhydride)s, 4,4′-[sulfonylbis(1,4-phenylene)dioxy]diphthalic anhydride ( IV ) and 4,4′-[sulfonylbis(2,6-dimethyl-1,4-phenylene)dioxy]diphthalic anhydride (Me- IV ), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of the bisphenolate ions of 4,4′-sulfonyldiphenol and 4,4′-sulfonylbis(2,6-dimethylphenol) with 4-nitrophthalonitrile in N,N-dimethylformamide (DMF). High-molar-mass aromatic poly(ether sulfone imide)s were synthesized via a conventional two-stage procedure from the bis(ether anhydride)s and various aromatic diamines. The inherent viscosities of the intermediate poly(ether sulfone amic acid)s were in the ranges of 0.30–0.47 dL/g for those from IV and 0.64–1.34 dL/g for those from Me- IV. After thermal imidization, the resulting two series of poly(ether sulfone imide)s had inherent viscosities of 0.25–0.49 and 0.39–1.19 dL/g, respectively. Most of the polyimides showed distinct glass transitions on their differential scanning calorimetry (DSC) curves, and their glass transition temperatures (T_g) were recorded between 223–253 and 252–288°C, respectively. The results of thermogravimetry (TG) revealed that all the poly(ether sulfone imide)s showed no significant weight loss before 400°C. The methyl-substituted polymers showed higher T_g's but lower initial decomposition temperatures and less solubility compared to the corresponding unsubstituted polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1649–1656, 1998     

Synthesis and Properties of Aromatic Poly(Ether Sulfone)s and Poly(Etherketone)s Containing Naphthalene or Quinoline Units,and Methyl-Substituted Biphenyl-4,4′-Diols

Abstract

A series of poly(ether sulfone)s and poly(ether ketone)s were synthesized from combinations of 1,5- and 2,6-bis(4-fluorosulfonyl)naphthalene, 2,6-bis(4-fluorobenzoyl)naphthalene, and 2,6-bis(4-fluorobenzoyl)quinoline with 3,3′,5,5′-tetramethylbiphenyl-4,4′-diol and 2,2′,3,3′,5,5′-hexamethylbiphenyl-4,4′-diol. The polycondensations proceeded quantitatively in diphenylsulfone in the presence of anhydrous potassium carbonate to afford polymers with inherent viscosities between 0.40 and 1.28 dL/g measured in N-methyl-2-pyrrolidone or concentrated sulfuric acid. The tetramethyl- and hexamethyl-substituted aromatic polyethers exhibited good thermal stability, did not decompose below 330°C in both air and nitrogen atmospheres, and had higher glass transition temperatures than the corresponding unsubstituted polymers. The methylsubstituted poly(ether sulfone)s and poly(ether ketone)s showed good solubility in such common organic solvents as N-methyl-2-pyrrolidone, N,N-dimethylacetamide, tetrahydrofuran, chloroform, and 1,4-dioxane.     

一种用于质子交换膜材料的磺化聚醚醚砜的合成

以发烟硫酸和4,4′-二氯二苯砜为原料,通过磺化反应,制得磺化二氯二苯砜,然后利用亲核缩聚反应,调整磺化单体和非磺化单体的比例,与四甲基联苯二酚进行聚合,制取了系列具有不同磺化度的聚醚醚砜,并对聚合物的结构进行了研究.     

Direct copolymerization of sulfonated poly(phthalazinone arylene ether)s for proton‐exchange‐membrane materials

Sulfonated poly(phthalazinone ether ketone) (SPPEK) copolymers and sulfonated poly(phthalazinone ether sulfone) (SPPES) copolymers containing pendant sodium sulfonate groups were prepared by direct copolymerization. The reaction of disodium 3,3′‐disulfonate‐4,4′‐difluorobenzophenone (SDFB‐Na), 4,4′‐difluorobenzophenone (DFB), and 4‐(4‐hydroxyphenyl)‐1(2H)‐phthalazinone (DHPZ) at 170 °C in N‐methyl‐2‐pyrrolidione containing anhydrous potassium carbonate gave SPPEKs. SPPESs were similarly obtained with 3,3′‐disulfonate‐4,4′‐difluorophenyl sulfone, 4‐fluorophenyl sulfone (DFS), and DHPZ as monomers. The sulfonic acid groups, being on deactivated positions of the polymer backbone, were expected to be hydrolytically more stable than postsulfonated polymers. Fourier transform infrared and ¹H NMR were used to characterize the structures and degrees of sulfonation of the sulfonated polymers. Membrane films of SPPEKs with SDFB‐Na/DFB molar feed ratios of up to 60/40 and SPPESs with sulfonated 4‐fluorophenyl sulfone/DFS molar feed ratios of up to 50/50 were cast from N,N‐dimethylacetamide polymer solutions. Membrane films in acid form were then obtained by the treatment of the sodium‐form membrane films in 2 N sulfuric acid at room temperature. An increase in the number of sulfonate groups in the copolymers resulted in an increased glass‐transition temperature and enhanced membrane hydrophilicity. The sodium‐form copolymers were thermally more stable than their acid forms. The proton conductivities of the acid‐form copolymers with sulfonated monomer/unsulfonated monomer molar feed ratios of 0.5 and 0.6 were higher than 10^?2 S/cm and increased with temperature; they were less temperature‐dependent than those of the postsulfonated products. SPPESH‐50 showed higher conductivity than the corresponding postsulfonated poly(phthalazinone ether sulfone). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2731–2742, 2003     

Synthesis and Characterization of Poly(ether ether ketone)s with (2,5‐dihydroxy)phenyl Side Group

A new monomer, (2,5‐dimethoxy)phenylhydroquinone (DMPH), was prepared in a two‐step synthetic procedure. One aromatic poly(ether ether ketone)s with 2,5‐dimethoxy phenyl side group (DMP‐PEEK) was synthesized via an aromatic nucleophilic substitution reaction with 4,4′‐difluorobenzophenone (DFB). Poly(ether ether ketone)s with 2,5‐dihydroxy phenyl side group (DHP‐PEEK) was obtained via hydrolysis of methoxy group on the DMP‐PEEK. Both of the high molecular weight polymers could be obtained despite the steric effect of the bulky pendant groups. The two polymers have good solubility at room temperature.     

Synthesis and characterization of aromatic poly(ether sulfone)s containing pendant sodium sulfonate groups

Poly(ether sulfone)s containing pendant sodium sulfonate groups were prepared by the aromatic nucleophilic substitution reaction of 4,4′-dichlorodiphenylsulfone ( 1 ) and sodium 5,5′-sulfonylbis (2-chlorobenzenesulfonate) ( 2 ) with bisphenols ( 3 ) in the presence of potassium carbonate in N,N-dimethylacetamide. A new monomer 2 containing the sodium sulfonate groups was synthesized by the sulfonation of 1 with fuming sulfuric acid. The polycondensation proceeded smoothly at 170°C and produced the desired poly(ether sulfone)s containing the sodium sulfonate with inherent viscosities up to 1.2 dL/g. The polymers were quite soluble in strong acid, dipolar aprotic solvents, m-cresol, and dichloromethane. The thermogravimetry of the polymers showed excellent thermal stability, indicating that 10% weight losses of the polymers were observed in the range above 460°C in nitrogen atmosphere. Both the glass transition temperatures and hydrophilicity of the polymers increased with increasing their concentrations of sodium sulfonate groups. © 1993 John Wiley & Sons, Inc.     

Co‐poly(aryl ether sulfone)s containing phthalimidine moiety in the main chain

Several new co‐poly(arylene ether sulfone)s have been prepared by the reaction of 4,4′‐fluorodiphenyl sulfone (FDS) with different bisphenols namely 4,4′‐isopropylidenediphenol (BPA), 4,4′‐hexafluoroisopropylidenediphenol (6F‐BPA), and N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine(PA). The homo‐poly(arylene ether sulfone)s are named as 1a, 2a, and 3a. The copolymers namely 2b, 2c, 2d and 3b, 3c, 3d have been prepared, respectively, on reaction of FDS with BPA or 6F‐BPA using different molar ratios of PA such as 25, 50, and 75. The poly(aryl ether sulfone)s 1a containing PA unit in the main chain showed a very high glass transition temperature of 280°C and an outstanding thermal stability up to 510°C for 5% weight loss under synthetic air. Depending on the mole% of PA, the glass transition temperatures of the copolymers can be varied. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 84 MPa and Young's modulus up to 3.16 GPa. The films of these polymers showed low water absorption of 0.24%. Copyright © 2009 John Wiley & Sons, Ltd.     

Poly(aryl ether)s containing o‐terphenyl subunits. II. Random poly(ether sulfone)s

The synthesis of a new A₂X‐type difluoride monomer, N‐2‐pyridyl‐4′,4″‐bis‐(4‐fluorobenzenesulfonyl)‐o‐terphenyl‐3,6‐dimethyl‐4,5‐dicarboxylic imide ( 3 ), is described. The monomer 3 was incorporated into a series of copoly(aryl ether sulfone)s by polymerization of 4,4′‐isopropylidenediphenol and 4,4′‐difluorophenylsulfone. The incorporation of monomer 3 had an observable effect on both the glass‐transition temperature of poly(aryl ether sulfone)s and the tendency for macrocyclic oligomers to form during polymerization. Replacement of the pyridyl imide group via a transimidization reaction with propargyl amine proceeded quantitatively and without polymer degradation. The acetylene containing copoly(aryl ether sulfone) could be crosslinked by simple thermal treatment, resulting in an increase in the glass‐transition temperature and solvent resistance. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 9–17, 2000     

Side-Chain Sulfonated Poly(arylene ether)s for Fuel Cell Applications

Summary: Poly(arylene ether sulfone)s of high molecular weight and narrow molecular weight distribution were obtained by melt polycondensation of 4,4′-difluorodiphenyl- sulfone and trimethylsilylethers of 4,4′-dihydroxydiphenylsulfone and phenylhydroquinone using CsF as catalyst. Although a block-like structure of the polymers could be expected from the course of reaction, only a single T_g ranging from 190 °C to 230 °C could be detected by DSC and which depended on the copolymer composition. Contrary to the sulfonation of similar poly(ether ether ketone)s the poly(arylene ether sulfone)s here reported were sulfonated both in the side chain and the main chain. Nonetheless the sulfonated poly(arylene ether sulfone)s showed high hydrolytic stability in water at 130 °C.     

Gas transport properties of novel poly(arylene ether ketone)s containing dibenzoylbiphenyl and benzonaphthone moieties

In this work we present the results from studies on novel poly(arylene ether ketone)s, including gas permeability, wide-angle x-ray diffraction (WAXD), and dynamic mechanical analysis (DMA). Poly(arylene ether ketone)s containing 2,2′- and 3,3′-dibenzoylbiphenyl (DBBP) moieties were characterized to study the effect of biphenyl substitution on gas transport properties. Gas permeabilities of naphthalene-containing poly(arylene ether ketone)s were also measured. Higher permeabilities were observed for polymers prepared with 6F-BPA, compared to 9,9-bis(4-hydroxyphenyl)fluorene (HPF). The naphthalene-containing polymers exhibited higher permeabilities than the DBBP polymers, except for a polymer having the 2,2′-DBBP and tetramethylbiphenyl moieties. Based on our work, and results reported in the literature, the 3,3′-DBBP polymers showed the lowest permeabilities for DBBP-containing poly-(arylene ether ketone)s. The low permeabilities are due to more efficiently packed chains brought on by greater flexibility of the backbone, compared to the other polymers studied. DMA studies confirmed the higher barriers to rotation which are believed to be responsible for 2,2′-DBBP polymers having similar selectivities compared to 3,3′-DBBP polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 425–431, 1998     

Controlled sulfonation of poly(arylene ether sulfone)s and poly(arylene ether ketone)s with different molecular structures for polymer electrolyte membranes

Poly(arylene ether sulfone) copolymers derived from 9,9-bis(4-hydroxyphenyl)fluorene, bisphenol S and 4,4′-difluorodiphenylsulfone and poly(arylene ether ketone) copolymers derived from 4-phenoxybiphenyl, diphenyl ether and isophthaloyl chloride were prepared as precursor polymers for sulfonation reaction in which sulfonic groups are introduced quantitatively into specified positions. Sulfonation reaction for these two series of copolymers by concentrated sulfuric acid was successfully carried out to give sulfonated polymers with controlled positions and degree of sulfonation. Thermal stability, moisture absorption and proton conductivity for these two series of copolymers were measured and the results were compared to those of perfluorosulfonic acid polymers.     

Synthesis and properties of poly(ether imide)s based on the bis(ether anhydride)s from hydroquinone and its derivatives

Four bis(ether anhydride)s, 4,4′‐(1,4‐phenylenedioxy)diphthalic anhydride (IV), 4,4′‐(2,5‐tolylenedioxy)‐diphthalic anhydride (Me‐IV), 4,4′‐(2‐chloro‐1,4‐phenylenedioxy)diphthalic anhydride (Cl‐IV), and 4,4′‐(2,5‐biphenylenedioxy)diphthalic anhydride (Ph‐IV), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 4‐nitrophthalonitrile with the potassium phenoxides of hydroquinone and various substituted hydroquinones such as methylhydroquinone, chlorohydroquinone, and phenylhydroquinone in N,N‐dimethylformamide, followed by alkaline hydrolysis and dehydration. Four series of poly(ether imide)s were prepared from bis(ether anhydride)s with various aromatic diamines by a classical two‐step procedure. The inherent viscosities of the intermediate poly(amic acid)s were in the range of 0.40–2.63 dL/g. Except for those derived from p‐phenylenediamine and benzidine, almost all the poly(amic acid)s could be solution‐cast and thermally converted into transparent, flexible, and tough polyimide films. Introduction of the chloro or phenyl substituent leads to a decreased crystallinity and an increased solubility of the polymers. The glass transition temperatures (T_g) of these polyimides were recorded in the range of 204–263°C. In general, the methyl‐ and chloro‐substituted polyimides exhibited relatively higher T_gs, whereas the phenyl‐substituted ones exhibited slightly lower T_gs compared to the corresponding nonsubstituted ones. Thermogravimetric analysis (TG) showed that 10% weight loss temperatures of all the polymers were above 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 665–675, 1999     

Synthesis and characterization of aromatic poly(ether ketone)s containing cyclotriphosphazene units. II

A new monomer di(4‐carboxyphenoxy) tetrakis(4‐fluorophenoxy)cyclotriphosphazene 1 was synthesized in a two‐step reaction sequence. The direct polycondensation of 1 and/or 4,4′‐dicarboxydiphenylether with aromatic ethers was carried out in P₂O₅/methanesulfonic acid (Eaton's reagent) at 120 °C for 3 h to give two series of aromatic poly(ether ketone)s containing cyclotriphosphazene units. The effect of the introduction of the cyclotriphosphazene group on the solubility and thermal properties of these polymers was discussed with relation to the cyclotriphosphazene contents. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2300–2305, 2000     

Poly(ether imide)s derived from phthalazinone‐containing dianhydrides

An unsymmetrical and noncoplanar heterocyclic dianhydride was synthesized from a bisphenol‐like phthalazinone, 4‐(4‐hydroxylphenyl)‐2,3‐phthalazin‐1‐one, and a series of novel poly(ether imide)s based on it, with intrinsic viscosities of 0.67–1.42 dL/g, were obtained by one‐step solution polymerization in m‐cresol at 200 °C for 20 h. The polymers were readily soluble in N‐methyl‐2‐pyrrolidinone and m‐cresol. The poly(ether imide)s derived from 4,4′‐oxydianiline and 4,4′‐methylenedianiline were also very soluble in chloroform, 1,1′,2,2′‐tetrachloroethane, and N,N‐dimethylacetamide. The glass‐transition temperatures were 289–326 °C, as determined by differential scanning calorimetry. All the degradation temperatures for 5% weight loss occurred above 482 °C in nitrogen. The tensile strength of thin films of some of the polymers varied from 103.1 to 121.4 MPa. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6089–6097, 2004     

Fully aromatic poly(ether ketone)s bearing macrocycle pendants: Synthesis and crosslinking

This study reports a method to prepare fully aromatic poly(ether ketone) thermosets. The cyclization of 2′,5′‐dimethoxy[1,1′‐biphenyl]‐2,5‐diol and a difluoro monomer was carried out under pseudo high dilution condition. Two types of fully aromatic poly(ether ketone)s with macrocycle were successfully prepared by copolymerization of macrocycle of aryl ether ketone containing hydroxyphenyl groups, 4,4′‐(hexafluoroisopropylidene)diphenol (HFBPA), and 4,4‐difluorobenzophenone. The obtained copolymers have high molecular mass, good solubility, and high glass transition temperatures in the presence of CsF, the crosslinking reaction of copolymers occurred and afforded fully aromatic thermoset poly(aryl ether ketone)s by ring‐opening reaction driven by entropy. After crosslinking, these copolymers show much higher glass transition temperatures, excellent thermal stability, and better mechanical strength. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7002–7010, 2008     

Preparation and characterization of branched and linear sulfonated poly(ether ketone sulfone) proton exchange membranes for fuel cell applications

Branched sulfonated poly(ether ketone sulfone)s (Br‐SPEKS) were prepared with bisphenol A, bis(4‐fluorophenyl)sulfone, 3,3′‐disodiumsulfonyl‐4,4′‐difluorobenzophenone, and THPE (1,1,1‐tris‐p‐hydroxyphenylethane), respectively, at 180 °C using potassium carbonate in NMP (N‐methylpyrrolidinone). THPE, as a branching agent, was used with 0.4 mol % of bisphenol A to synthesize branched copolymers. Copolymers containing 10–50 mol % disulfonated units were cast from dimethylsulfoxide solutions to form films. Linear sulfonated poly(ether ketone sulfone)s (SPEKS) were also synthesized without THPE. The films were converted from the salt to acid forms with dilute hydrochloric acid. A series of copolymers were studied by Fourier transform infrared, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water and methanol. The ion‐exchange capacity (IEC), a measure of proton conductivity, was evaluated. The synthesized Br‐SPEKS and SPEKS membranes exhibit conductivities (25 °C) from 1.04 × 10^?3 to 4.32 × 10^?3 S/cm, water swell from 20.18 to 62.35%, IEC from 0.24 to 0.83 mequiv/g, and methanol diffusion coefficients from 3.2 × 10^?7 to 4.7 × 10^?7 cm²/S at 25 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1792–1799, 2008     

Characterization and comparison of poly(aryl ether ketone)s containing dibenzoylbiphenyl moieties: Effects of changes in biphenyl substitution pattern on thermal and mechanical properties

A monomer, 3,3′-bis (4-fluorobenzoyl) biphenyl, was prepared in high yield in two steps from inexpensive 3-chlorobenzoyl chloride and fluorobenzene, and polymerized by nucleophilic displacement reaction with various bisphenol monomers in tetramethylene sulfone to produce a series of high molecular weight poly(aryl ether ketone)s containing 3,3′-dibenzoylbiphenyl (DBBP) moieties. The spectroscopic, thermal, and thermomechanical properties of these polymers and related isomeric polymers having 2,2′-and 4,4′-DBBP units were determined and compared to study the effects of changes in the substitution pattern of the biphenyl unit. Except for the 2,2′-DBBP series of polymers, T_gs were found to increase with increasing linearity of the DBBP unit. The 2,2′-DBBP series of polymers had exceptionally high T_gs due to the sterically restricted motions in the biphenyl unit caused by the 2,2′-substitution. In addition, they also showed evidence for torsion with the 2,2′-DBBP unit, whereas in other isomeric polymers the DBBP units are believed to be relatively coplanar. Thermal stabilities and tensile moduli for these polymers proved to be independent of substitution patterns. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of new highly organosoluble poly(ether imide)s based on 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride

A new bis(ether anhydride), 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride ( 3 ), was prepared in three steps: the nitro displacement of 4‐nitrophthalonitrile with 2,2‐bis(4‐hydroxy‐3,5‐dimethylphenyl)propane, the alkaline hydrolysis of the intermediate bis(ether dinitrile), and the subsequent dehydration of the resulting bis(ether diacid). A series of new highly soluble poly(ether imide)s with tetramethyl and isopropylidene groups were prepared from the bis(ether anhydride) 3 with various diamines by a conventional two‐stage synthesis including polyaddition and chemical cyclodehydration. The resulting poly(ether imide)s had inherent viscosities of 0.54–0.73 dL g^?1. Gel permeation chromatography measurements revealed that the polymers had number‐average and weight‐average molecular weights of up to 54,000 and 124,000, respectively. All the polymers showed typical amorphous diffraction patterns. All of the poly(ether imide)s showed excellent solubility and were readily dissolved in various solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, pyridine, cyclohexanone, tetrahydrofuran, and even chloroform. Most of the polymers could be dissolved with chloroform concentrations as high as 30 wt %. These polymers had glass‐transition temperatures of 244–282 °C. Thermogravimetric analysis showed that all polymers were stable, with 10% weight losses recorded above 463 °C in nitrogen. These transparent, tough, and flexible polymer films were obtained through solution casting from N,N‐dimethylacetamide solutions. These polymer films had tensile strengths of 81–102 MPa and tensile moduli of 1.8–2.0 GPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2556–2563, 2002     

Synthesis of copolymers of poly(ether sulfone ether ketone ketone) and poly(ether ketone diphenyl ketone ether ketone ketone) by electrophilic Friedel–Crafts solution polycondensation

A new monomer, 4,4′‐bis(4‐phenoxybenzoyl)diphenyl(BPOBDP), was synthesized via a two‐step synthetic procedure. A series of novel poly(ether sulfone ether ketone ketone)/poly(ether ketone diphenyl ketone ether ketone ketone) copolymers were prepared by electrophilic Friedel–Crafts solution copolycondensation of isophthaloyl chloride (IPC) with a mixture of 4,4′‐diphenoxydiphenylsulfone (DPODPS) and 4,4′‐bis(4‐phenoxybenzoyl)diphenyl (BPOBDP), in the presence of anhydrous aluminum chloride and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The copolymers with 10–50 mol% DPODPS are semicrystalline and have remarkably increased T_gs over commercially available PEEK and PEKK. The copolymers with 40–50 mol% DPODPS had not only high T_gs of 170–172°C, but also moderate T_ms of 326–333°C, which are extremely suitable for melt processing. These copolymers have tensile strengths of 96.5–108.1 MPa, Young's moduli of 1.98–3.05 GPa, and elongations at break of 13–26% and exhibit excellent thermal stability and good resistance to acidity, alkali, and common organic solvents. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis,characterization, and comparison of properties of new fluorinated poly(arylene ether)s containing phthalimidine moiety in the main chain

Four new poly(arylene ether)s have been prepared by the reaction of N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine (PA) with four different perfluoroalkylated monomers namely 1,3‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) benzene, 4,4′‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) biphenyl, 2,6‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) pyridine, and 2,5‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) thiophene. The poly(arylene ether)s were characterized by different spectroscopic, thermal, mechanical, and electrical techniques. The poly(arylene ether) containing quadriphenyl unit in the main chain showed very high glass transition temperature of 291°C and outstanding thermal stability upto 556°C for 10% weight loss under a 4:1 nitrogen:oxygen mixture. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 75 MPa and elongation at break upto 32%. The films of these polymers showed low water absorption of 0.26%. Copyright © 2009 John Wiley & Sons, Ltd.