On-line multidimensional supercritical fluid chromatography/capillary gas chromatography

A new analytical technique combining on-line supercritical fluid chromatography with capillary gas chromatography has been developed. The supercritical fluid sample effluent is decompressed through a restrictor directly into a conventional capillary gas chromatographic injection port. This technique allows for not only direct (100%) sample transfer from the supercritical fluid chromatograph to the gas chromatograph but also for selective or multi-step heartcutting of various sample peaks as they elute from the supercritical fluid chromatograph. Heartcut times are determined by monitoring the responses from the flame ionization or ultraviolet absorbance detectors on the supercritical fluid chromatograph. This report describes the operational setup and provides the results of heartcut reproducibility experiments using normal hydrocarbon and aromatic test mixtures. Results from studies where operational parameters were varied, such as GC injector temperature, will also be provided. The potential usefulness of this new technique for selective heartcutting will also be demonstrated using complex hydrocarbon streams.     

Sample introduction in high speed capillary gas chromatography; input band width and detection limits

The speed of analysis in capillary gas chromatography can be substantially increased by reduction of the column inner diameter. However, special demands are then posed upon instrumental design. In particular, the sampling system is highly critical because it has to be capable of delivering extremely small injection band widths which must be compatible with the column inside diameter. This study focuses on the evaluation of two potentially suitable sample introduction systems with respect to input band width and detection limits and their compatibility with small bore (≦ 100 μm) columns in capillary gas chromatography. One of them allows liquid on-column injection, based on liquid splitting, of only a few nl onto small bore (≦ 100 ?m) fused silica columns. For gases, input band widths as low as 1 ms are obtained with this system. The other one is part of a miniaturized gas chromatograph with extremely low dead volume interfaces and detector volumes. It allows input band widths for gases of a few ms. Without any preconcentration ppm concentrations are measured in gaseous samples with a 80 ?m thick film capillary column. It will be shown that a further reduction of the minimum detectable amount and analysis time is possible with this equipment.     

Two-dimensional capillary gas chromatography without intermediate trapping. Electron capture detector quantitation of an amino alcohol (KABI 2128) in serum after trifluoroacetylation

A two- dimensional gas chromatograph based on the Deans switching principle is described. The unit comprises two separate ovens, each containing a fused silica capillary column. The columns are joined in a specially designed manifold permitting heart cuts to be performed without significant decrease in efficiency. The switching speed and the retention time stability of the system made it possible to perform heart cuts of only a few seconds' duration. The system has been used under isothermal conditions for the determination of an amino alcohol (KABI 2128) in the low ng/ml range after trifluoroacetylation and with electron capture detection. A much shorter clean-up procedure could be used in combination with the two-dimensional gas chromatograph as compared to a method using a single glass capillary column.     

Identification of oxygenated polycyclic aromatic hydrocarbons in diesel particulate matter by capillary gas chromatography and capillary gas chromatography/mass spectrometry

Summary Using a two-step liquid chromatographic separation on normalphase cartridges, crude extracts of diesel particulate matter can be separated without time-consuming sample handling into special fractions which mainly contain slightly-polar oxygenated polycyclic aromatic hydrocarbons (oxy-PAH) and nitrated polycyclic aromatic hydrocarbons (nitro-PAH). Subsequent analysis was by fused-silica capillary gas chromatography on a SE54 column along with flame-ionisation (GC/FID) and positive-ion electron-impact mass spectrometric detection (GC/MS) respectively. A number of individual oxy-PAH belonging to four different chemical classes (ketones, quinones, anhydrides and aldehydes) and several individual nitro-PAH were characterized by their retention times and mass spectra. Presented at the 15th International Symposium on Chromatography, Nürnberg, October 1984     

Evaluation of capillary gas chromatography columns for the determination of free volatile amines after solid-phase microextraction

Summary Gas-liquid chromatographic capillary columns coated with 14% diphenyldimethylpolysiloxane, base-deactivated 5% diphenyldimethylpolysiloxane, or poly(ethylene glycol), and deactivated porous polymer for capillary gas-solid chromatography were evaluated for analysis of low-molecular-weight (C₁−C₉) amines. Solid-phase microextraction with a polydimethylsiloxane fiber was used for headspace sampling and for introduction of the sample into the gas chromatograph. As expected, basic of aliphatic gaseous or volatile aliphatic amines (carbon number: C₁−C₄). A thick (e. g. 3 μm) film of 5% diphenyldimethylpolysiloxane enabled determination of analytes in a wider molecular-weight range (C₃−C₉) with acceptable efficiency and resolution.     

Construction and application of a cold on-column injection system for capillary gas chromatography

A cold on-column injection system for capillary gas chromatography (GC) applications was constructed. It was based upon a conventional split/splitless capillary GC inlet, which in turn was a modification of a conventional packed GC column inlet. The heart of the laboratory constructed cold on-column inlet design was a disposable pyrex micro-sampling pipet, which functioned as a needle guide for sample injection. The sample was injected through a traditional GC septum. Construction of the injection system is described and applications are illustrated by separations of a variety of complex mixtures.     

Quantitative determination of paraffin oil in blood by capillary gas chromatography

A capillary gas chromatographic method is described for the quantitative determination of liquid paraffin in blood. Paraffin is extracted from blood into n-heptane. After solvent evaporation and dissolution of the residue in 100–200 μl n-heptane one μl is injected into a gas chromatograph fitted with a fused silica capillary column (Permabond® OV-1-CB-0.1, 10 m × 0.32 mm i.d.) and flame ionization detector. Analysis is performed by using an oven program [50°C (3 min)?285°C (5 min), rise 10%min]. The sensitivity (1.5 ng hexadecane) and the reproducibility prove the applicability of the method for the determination of liquid paraffin in blood and for the study of the stability of the liquid paraffin hollow fiber membranes used in an extracorporeal liver support system.     

Qualitative supercritical fluid extraction coupled to capillary gas chromatography

The usefulness and ease of utilizing supercritical fluid extraction (SFE) directly coupled to capillary gas chromatography (GC) as quantitative or qualitative analytical problem-solving tools will be demonstrated. As an alternative to conventional liquid solvent extractions, SFE presents itself as a means to achieve high extraction efficiencies of different compounds in complex solid matrices in very rapid tims frames. Moreover, SFE has an additional advantage of being able to achieve distinct extraction selectivities as a function of the solubilizing power of the supercritical fluid extracting phase. For on-line SFE/GC, the extraction effluent is directly transferred to the analytical chromatograph. On-line SFE/GC involves the decompression of pressurized extraction effluent directly into a heated, unmodified capillary split injection port of the GC. In this respect, SFE introduction into GC can be used as an alternative means of GC injection, comparable to such modes of injection as pyrolysis and thermal desorption. This paper will show applications of SFE/GC where mass spectrometric detection together with flame ionization detection was used for component identification from environmental, tobacco, and petroleum matrices.     

Practical limitations of capillary gas chromatography

Glass capillary gas chromatography is a high resolution separation method which allows the qualitative and quantitative analysis of even complex mixtures, which may contain many components–also isomeric–in a wide range of volatilities, polarities and concentrations. The principal limitation of gas chromatographic application is given by an insufficient volatility of the species to be separated. Elevated temperatures have to be applied if the application range is to be extended and to achieve steep peak profiles, i.e. low detection limits at high resolution. The use of elevated temperatures is limited, of course, by the temperature stability of both the solvent (stationary liquid and support) and the solutes. The problems of trace analysis for low volatility compounds at high resolution and its limitational parameters regarding sampling, separation and detection are discussed. The applicability of glass capillary columns in this field is influenced by the following parameters: tailing behaviour; irreversible adsorption of polar and decomposition of unstable solutes; thermal stability of stationary liquid (including the support deactivation); separation efficiency and sample capacity (film thickness). Multidimensional gas chromatography using capillary columns coupled either with a packed or another capilllary column for preseparations may be applied with advantage in the analysis of complex mixtures.     

Quantitative analysis of ethylenediamine in plasma by capillary column gas chromatography

A specific and sensitive method for the determination of ethylenediamine in human plasma is described. The aqueous sample is treated with m-toluoyl chloride, yielding the N,N′-bis(m-toluoyl) derivative of the diamine, which is extracted into dichloromethane and quantitated after “on column” methylation by capillary gas liquid chromatography with alkali flame ionization detection. The corresponding derivative of putrescine serves as internal standard. The assay is reproducible and calibration curves are linear over the concentration range 0.05 to 10 μg · ml^?1. The lower detection limit is about 10 ng · ml^?1. The structures of the compounds of interest eluting from the capillary column are examined by gas liquid chromatography/mass spectrometry. The assay has been applied to the analysis of ethylenediamine in plasma following the administration of aminophylline and ethylenediamine in a cross-over study to patients with bronchopulmonary diseases. The method also proves suitable for measuring other primary and secondary amines and diamines in aqueous solutions by gas liquid chromatography.     

Column switching applied to capillary gas chromatography/fourier transform infrared spectroscopy

A dual oven gas chromatograph incorporating a micro, mechanical switching valve has been interfaced to an FTIR spectrometer. With this system, each oven can be operated with independent temperature control. Complete choice of the columns' type and capacity gives flexibility in the separation prior to spectroscopic evaluation. An application which demonstrates some of the advantages of column switching in GC/FTIR is presented. Minor sample components have been successfully analyzed by heart-cutting the appropriate section of the separation from a high to a low capacity column. In this way, the dynamic range of the technique is effectively increased while an efficient chromatographic inlet to the FTIR is maintained.     

Special cooling system for the on-column injector in capillary gas chromatography eliminating discrimination of sample compounds

On-column injection into a hot gas chromatograph oven involves the danger that the bottom part of the needle is warmed up above the boiling point of the solvent in the sample. Consequently parts of the sample are evaporated out of the needle instead of being introduced as a liquid into the capillary column. This causes losses and hence discrimination of the less volatile parts of the sample which remain in the needle. A technical solution is proposed using a system for cooling the capillary during the injection, down to the injection point in the oven.     

Current technological challenges in capillary supercritical fluid chromatography

In cases where high efficiency is required to resolve complex mixtures of either thermally labile or nonvolatile organic compounds, capillary supercritical fluid chromatography may be the most desirable analytical method. While great strides in this new technology have been made over the last few years, several problem areas are requiring increased attention. These include sample introduction systems, pressure reduction at the end of the column, column stability in various supercritical mobile phases, and migration of polar solute molecules. This paper describes the state-of-the-art in capillary SFC with emphasis on the progress made and future needs in the solutions to these specific problems.     

Automatic simulated distillation of heavy petroleum fractions up to 800°C TBP by capillary gas chromatography. Part I: Possibilities and limits of the method

The characterization of heavy petroleum fractions is essential for the design and improvement of cracking plants converting heavy feedstock into valuable “white” products. Conventional simulated distillation methods using packed columns are unsuitable for this purposes, being limited to boiling points up to about 600°C. The method presented is able to cover a boiling points interval ranging from about 150°C up to around 800°C. It employs a short, nonpolar, highly thermostable capillary column routinely operated at temperatures around 430°C. The analytical system is based on a high temperature versions of a fully automatic, capillary dedicated gas chromatograph. The experimental data demonstrate that cold on-column injection is the sole sampling system suitable for such heavy compounds. The conversion of the retention times into boiling points, based on the use of low molecular weight polyethylenes, is extremely reliable, as demonstrated by the excellent retention time reproducibilities. The lower part (up to 550–600°C TBP) of the boiling point distribution curves of heavy petroleum fractions obtained on capillary columns fits well with the corresponding distribution curves based on packed column data. For the petroleum fractions fully eluted from the column the quantitative results obtained either using internal standards or by direct processing of the elution curves are in excellent agreement (less than 0.3 weight% differences). The method has been applied to the determination of the true boiling points corresponding to short path vacuum distillation (DISTACT) cut points over 300°C.     

A new configuration for coupling purge-and-trap/cryogenic focusing/capillary column gas chromatography with splitless injection mode

A new configuration for coupling a purge-and-trap unit to a capillary column gas chromatograph via a cryogenic focusing interface has been developed. In this configuration, the precolumn of the cryogenic focusing interface was inserted through the septum of a split/splitless injection port where it served as both sample transfer and carrier gas supply lines. The injection port of the gas chromatograph was modified by plugging the carrier gas and the septum purge lines. This configuration allowed for the desorption of analytes at high flow rates while maintaining low, analytical-column flow rates which are necessary for optimum capillary column operation. The capillary column flow rate is still controlled by the column backpressure regulator. Chromatograms of purgeable aromatics exhibited improved resolution, especially for early eluting components compared to those obtained by direct liquid injection using the normal splitless injection mode. Quantitative sample transfer to the analytical column afforded excellent linearity and reproducibility of compounds studied.     

Some applications of capillary gas chromatography in the chemical industry

About three years ago, fused silica capillary columns were introduced in the Quality Control Laboratory of the Shell refinery/chemical complex at Pernis. In general, long, thick-film, wide-bore capillary columns are used together with low split ratios and hydrogen as carrier gas. These conditions enable the analysis of relatively large sample amounts, resulting in low detection limits for the minor components without overloading by the major components, while still maintaining a satisfactory resolution. A number of applications are shown, such as the analysis of complex mixtures, the determination of trace impurities and the analysis of residual volatiles in polymers.     

Supercritical fluid injection of high-molecular-weight polycyclic aromatic compounds in capillary supercritical fluid chromatography

A sample introduction system for capillary supercritical fluid chromatography, which allows the dissolution of the sample in the supercritical mobile phase before being introduced into the column, was constructed and evaluated. Supercritical n-pentane was shown to solvate high-molecular-weight polycyclic aromatic compounds that could not be solvated using typical liquid solvents. In addition, split injection of a supercritical fluid solution was found to be more reproducible than split injections of a liquid solution. The potential of such an injection system was demonstrated, although further developments are needed in order to make the technique of practically utility.     

Polar solvents for the desorption of a liquid chromatographic precolumn coupled on-line with a capillary gas chromatograph

Coupling column liquid chromatography and gas chromatography on-line is becoming more important in analytical chemistry. Especially when large amounts of polar solvents can be introduced into the gas chromatograph without any problem, the technique will offer new possibilities. With a DPTMDS retention gap, evaporation rates and flooded zones of some solvents have been determined. Two modes of operation using partially concurrent solvent evaporation conditions are discussed: (1) injecting a sample via a loop of an LC valve followed by introduction into the gas chromatograph with an LC pump; (2) trace enrichment on a precolumn followed by on-line desorption with n-propanol into the gas chromatograph. Preliminary results for a splitter system, inserted between the retention gap and the analytical column which allows a considerable increase of the evaporation rate are also presented.     

Automated at-column injection into narrow bore capillary GC columns

An injector designed for automatic direct liquid injection into narrow bore capillary GC columns has been constructed and evaluated. The tip of the syringe needle is aligned with, and positioned close to, the column entrance in a small, pressurized cavity: when the sample is dispensed it is immediately forced into the column by the action of the surrounding carrier gas. A standard autosampler equipped with a standard stainless steel syringe needle was utilized for at-column sample transfer into 100 μm i.d. columns. RSD values for n-alkanes were between 0.1 and 0.3% for relative area counts and approximately 1% for absolute area counts.     

Characterization of Saccharomyces Sp. through determination of amino acid profiles by capillary gas chromatography

The Saccharomyces strains uvarum, montuliensis, bayanus, capensis and florentinus were grown in liquid media prepared from a 1% aqueous glucose solution to which 0.05% of ammonium sulfate or urea were added as the only nitrogen supply. The amino acids exuded during incubation were isolated by cation exchange and derivatized as the corresponding N,O-heptafluorobutyryl isopropyl esters. Separation was achieved on a highly deactivated glass capillary column coated with OV-101. A characteristic amino acid profile was obtained for each of the species studied, allowing the construction of a chemotaxonomic tree, on the basis of present or absent acids.