Surface rheology of PEO-PPO-PEO triblock copolymers at the air-water interface: comparison of spread and adsorbed layers

The dilatational rheological properties of monolayers of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide)-type block copolymers at the air-water interface have been investigated by employing an oscillating ring trough method. The properties of adsorbed monolayers were compared to spread layers over a range of surface concentrations. The studied polymers were PEO26-PPO39-PEO26 (P85), PEO103-PPO40-PEO103 (F88), and PEO99-PPO65-PEO99 (F127). Thus, two of the polymers have similar PPO block size and two of them have similar PEO block size, which allows us to draw conclusions about the relationship between molecular structure and surface dilatational rheology. The dilatational properties of adsorbed monolayers were investigated as a function of time and bulk solution concentration. The time dependence was found to be rather complex, reflecting structural changes in the layer. When the dilatational modulus measured at different concentrations was replotted as a function of surface pressure, one unique master curve was obtained for each polymer. It was found that the dilatational behavior of spread (Langmuir) and adsorbed (Gibbs) monolayers of the same polymer is close to identical up to surface concentrations of approximately 0.7 mg/m2. At higher coverage, the properties are qualitatively alike with respect to dilatational modulus, although some differences are noticeable. Relaxation processes take place mainly within the interfacial layers by a redistribution of polymer segments. Several conformational transitions were shown to occur as the area per molecule decreased. PEO desorbs significantly from the interface at segmental areas below 20 A(2), while at higher surface coverage, we propose that segments of PPO are forced to leave the interface to form a mixed sublayer in the aqueous region.     

Interfacial rheology of petroleum asphaltenes at the oil-water interface

A biconical bob interfacial shear rheometer was used to study the mechanical properties of asphaltenic films adsorbed at the oil-water interface. Solutions of asphaltenes isolated from four crude oils were dissolved in a model oil of heptane and toluene and allowed to adsorb and age in contact with water. Film elasticity (G') values were measured over a period of several days, and yield stresses and film masses were determined at the end of testing. The degree of film consolidation was determined from ratios of G'/film mass and yield stress/G'. Asphaltenes with higher concentrations of heavy metals (Ni, 330-360 ppm; V, 950-1000 ppm), lower aromaticity (H/C, 1.24-1.29), and higher polarity (N, 1.87-1.99) formed films of high elasticity, yield stress, and consolidation. Rapid adsorption kinetics and G' increases were seen when asphaltenes were near their solubility limit in heptane-toluene mixtures (approximately 50% (v/v) toluene). In solvents of greater aromaticity, adsorption kinetics and film masses were reduced at comparable aging times. Poor film forming asphaltenes had yield stress/G' values ((1.01-1.21) x 10(-2)) more than 4-fold lower than those of good film forming asphaltenes. n-heptane asphaltenes fractionated by filtering solutions prepared at low aromaticity (approximately 40% toluene in mixtures of heptane and toluene) possessed higher concentrations of heavy metals and nitrogen and higher aromaticity. The less soluble fractions of good film forming asphaltenes exhibited enhanced adsorption kinetics and higher G' and yield stress values in pure toluene. Replacing the asphaltene solutions with neat heptane-toluene highlighted the ability of films to consolidate and become more elastic over several hours. Adding resins in solution to a partially consolidated film caused a rapid reduction in elasticity followed by gradual but modest consolidation. This study is among the first to directly relate asphaltene chemistry to adsorption kinetics, adsorbed film mechanical properties, and consolidation kinetics.     

Mechanisms of micellization and rheology of PEO-PPO-PEO triblock copolymers with various architectures

Micelle formation was followed by micro-DSC and rheology for aqueous solutions of two copolymers of PEO-PPO-PEO, the Pluronic F127 (from BASF) and the EG56 (from PolymerExpert), a branched copolymer built with three chains of F127 type. It is shown that micellization is endothermic and that, for both polymers, the enthalpy of formation/melting is proportional to total concentration. The rheology of the solutions was carefully analyzed, before gelation for F127, and it reveals firstly the progressive changes of solubility of the unimers (decease of relative solution viscosity), followed by micelle formation over a 10 degrees C range. In this range, the micelle concentration dependence on temperature was deduced from enthalpy measurements and the corresponding volume fractions were derived. Viscosity was interpreted within the framework of well-known theories for hard sphere suspensions (Krieger-Dougherty or Quemada) based on an analogy between micelles and nanosized hairy grain suspensions. The gel state is achieved due to formation of the colloidal crystal. For EG56, the rheology is quite different; as the aggregation increases with temperature, a progression is observed from Newtonian to visco-elastic liquid. The characteristic frequency, defined by the relation G(') = G('), for EG56 varies with temperature and the corresponding times increase by two orders of magnitude according to an Arrhenius law. The frequency dependence of G(') and G(') at different temperatures can be superposed with a horizontal shift factor and a small amplitude adjustment. There is no elastic solid formation in this case. The "gelation" of these two copolymers is compared to the physical gelation of cold-set gels (gelatin).     

Interfacial rheology of polyelectrolytes and polymer monolayers at the air–water interface

In this review, we describe interfacial rheology studies of polymer monolayers at the air–water interface. Since polyelectrolytes are usually soluble in water, the formation of surface monolayers requires the presence of a surfactant of opposite charge. The first part of the review is dedicated to these mixed monolayers. The second part is related to neutral monolayers that can be either adsorbed or deposited at the interface. Interfacial rheology studies of these systems are still scarce, despite a considerable interest: insoluble polymer monolayers in two dimensions are suitable model systems for the tests of polymer theories in two dimensions, such as and glass transition. The rheology of soluble polymer monolayers has important connections with the dynamic properties of dispersions stabilized with these polymers.     

Dilational rheology of spread and adsorbed layers of silica nanoparticles at the liquid-gas interface

This short review is devoted to recent achievements in studies of the dilational surface rheological properties of the systems containing complexes of silica nanoparticles with conventional surfactants. It is shown that there is a surfactant concentration range where the dynamic surface elasticity reaches extremely high values up to 1000 mN/m. This result can explain the formation of very stable foams and emulsions containing nanoparticles. In some surfactant concentration ranges the adsorption layer is characterized by a non-linear response to small compressions or expansions of the liquid surface. Possible causes of this behavior and the mechanism of main relaxation processes are briefly discussed.     

Adsolubilization of 2-naphthol into adsorbed layer of PEO-PPO-PEO triblock copolymers on hydrophilic silica

Adsolubilization of 2-naphthol into an adsorbed layer of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymers (Pluronics) on hydrophilic silica has been investigated. Four kinds of Pluronics (P103, P105, P123, and F108) were used in order to understand the effect of the hydrophobicity of surfactant on the adsolubilization. The order of the adsorption in the saturation level was found to be P123 approximately P103 > P105 > F108, meaning that Pluronics with higher hydrophobicity can adsorb preferentially to the silica surface. Indeed, this order was parallel to the order of the adsolubilization amount of 2-naphthol. In the case of co-addition of the Pluronics and 2-naphthol, the adsolubilization amount increased gradually at lower surfactant concentration regions, reached a maximum, and then decreased with increasing concentration of the Pluronics. The maximum amount appeared at critical polymolecular micelle concentration of each Pluronics. On the other hand, the final decrement was not observed when 2-naphthol was added after replacement of the Pluronics supernatant by the Pluronics free solution. These results suggest that adsolubilization behavior is influenced by the existence of the polymolecular micellar aggregates in the solution phase.     

Interfacial rheological studies of gelatin-sodium dodecyl sulfate complexes adsorbed at the air-water interface

The dilational rheological behavior of gelatin molecules adsorbed at the air-water interface has been studied as a function of sodium dodecyl sulfate (SDS) concentration for a 7 wt % gelatin-SDS solution at 40 degrees C. Binding of SDS molecules to the gelatin strands disrupts the cross-linked network structure of adsorbed gelatin molecules and results in a reduction of the surface elastic modulus of the adsorbed layer that continues until the bulk SDS concentration reaches 1 mM. Beyond this SDS concentration, the dilational rheological properties of the adsorbed gelatin layer are indistinguishable from those of pure SDS adsorbed layers.     

Interfacial behaviors of PMMA-PEO block copolymers at the air/water interface

Amphiphilic block copolymers are attracting con-siderable attention because they exhibit unique self- assembly properties in selective organic solvents[1―4]. Semicrystalline poly(ethylene oxide) (PEO), having many interesting physicochemical properties s…     

Interfacial deposition of functionalized copolymers onto nanoemulsions produced by the solvent displacement method

Cationic nanoemulsions containing an oily core as potential carriers of nucleic acids were prepared by a solvent displacement method in the presence of a nonionic surfactant (Pluronic F68). With a view to functionalize such nanoemulsions for further incorporation of a fusogenic peptide, a poly(maleic anhydride-alt-methyl vinyl ether) (M _n=67,000) grafted with variable amount of acetylspermine (or acetylspermidine) and decylamine was nanodeposited during the nanoemulsion formation step. Functionalized nanoemulsions were characterized in terms of particle size (by quasi-elastic light scattering and electron microscopy), electrophoretic mobility and long-term stability as a function of the amount of polymer used in the formulation. It was found that increases in the level of the copolymer led to a reduction in the particle size and a decrease in colloidal stability. In addition, the incorporation of the grafted copolymers at the interface of the nanoemulsions was clearly evidenced, a shift towards low pH at the point of zero charge being attributed to the formation of carboxylic groups induced by hydrolysis of the residual maleic anhydride groups of the copolymer. Received: 1 September 2000 / in revised form: 29 November 2000 Accepted: 12 December 2000     

Adsolubilization of 2-naphthol into adsorbed layers of triblock PEO-PPO-PEO copolymers on hydrophobic silica particles

Adsolubilization of 2-naphthol into an adsorbed layer of triblock poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO, Pluronics) copolymers on hydrophobically modified silica particles has been investigated. Four kinds of Pluronics (P103, P105, P123, and F108) were employed in order to understand the effect of the hydrophobicity of the surfactants on the adsolubilization. The amount of the Pluronics adsorbed of the maximum/saturation adsorption level was increased with a decrease in the HLB value, suggesting that the more hydrophobic Pluronics (P103 and P123) adsorb preferentially onto the hydrophobic silica surface over the more hydrophilic Pluronics (P105 and F108). The greater adsorbed amount of the more hydrophobic surfactants resulted in a greater amount of 2-naphthol adsolubilized into the adsorbed Pluronics layers. In the case of simultaneous addition of the Pluronics and 2-naphthol, the amount adsolubilized into the adsorbed P123 and P103 layers increased in their low-surfactant-concentration regime, reached a maximum, and then decreased with a further increase in the Pluronics concentration. On the other hand, for both the P105 and F108 copolymers, a decrease in the adsolubilized amount was not observed over the whole range of copolymer concentration investigated. This difference is attributed to a difference in the hydrophobicity of the micellar aggregates in solution and of the adsorbed layers on the hydrophobic surface. When 2-naphthol was added after replacement of the Pluronics supernatant by a surfactant-free solution, the final decrease in the adsolubilization was insignificant for all the Pluronics. Indeed, the maximum amount of adsolubilization was comparable to the corresponding amount obtained in the case of simultaneous addition.     

Interfacial rheology of an ultrathin nanocrystalline film formed at the liquid/liquid interface

We report the interfacial properties of monolayers of Ag nanoparticles 10-50 nm in diameter formed at the toluene-water interface under steady as well as oscillatory shear. Strain amplitude sweep measurements carried out on the film reveal a shear thickening peak in the loss moduli (G") at large amplitudes followed by a power law decay of the storage (G') and loss moduli with exponents in the ratio 2:1. In the frequency sweep measurements at low frequencies, the storage modulus remains nearly independent of the angular frequency, whereas G" reveals a power law dependence with a negative slope, a behavior reminiscent of soft glassy systems. Under steady shear, a finite yield stress is observed in the limit of shear rate .gamma going to zero. However, for .gamma > 1 s-1, the shear stress increases gradually. In addition, a significant deviation from the Cox-Merz rule confirms that the monolayer of Ag nanoparticles at the toluene-water interface forms a soft two-dimensional colloidal glass.     

Adsorption of polar lipids at the water-oil interface

Dietary fat has long been recognized as an essential component in nutrition. However, most of the lipids present in food need to be converted into more bioavailable compounds. Lipases have a crucial role in converting triglycerides into more polar lipids with increased water solubility and a tendency to form micelles. However, the surface active molecules generated by lipolysis may have a detrimental effect on the interfacial biocatalysis. In the present work we evaluate the interfacial properties of lipase-generated molecules during fat digestion. By using the pendant drop technique we assessed the amphiphilic character of fatty acid salts, monoglycerides, and diglycerides as individual surfactants and mixtures. The experimental results are fitted with a mathematical model, which assists in the determination of the interfacial properties of the surfactants. Our results show that monoglycerides have considerably higher interfacial activity than fatty acid salts and diglycerides. Therefore, the interface will soon be dominated by monoglycerides. The pH dependency of the interfacial activity of fatty acids is also explored in the current work. We believe that our results can contribute to a better understanding of the complex interfacial phenomena occurring during fat digestion.     

Aggregation of flexible-rigid-flexible triblock copolymers

We discuss the aggregation behavior of flexible-rigidflexible triblock copolymers in a selective solvent of low molecular weight. Aggregation may lead either to plates of (R) covered by brushes of (F), or to large “needles” (as a consequence of the Skoulios effect). In the absence of anisotropic bonding between adjacent rods, the “fence” morphology is not expected.     

Synthesis of PDMAEMA-PCL-PDMAEMA triblock copolymers

The synthesis of ABA triblock copolymers of the type PDMAEMA-PCL-PDMAEMA was achieved by atom transfer radical polymerization (ATRP) of DMAEMA using difunctional polycaprolactone (PCL) as macroinitiator. First, ring-opening polymerization (ROP) of ε-caprolactone (ε-CL) was carried out in the presence of 1,2-diaminoethane/tin (II) octanoate. Dihydroxy PCL thus obtained was end-functionalized in a quantitative manner using 2-bromoisobutyryl bromide. The resulting Br-PCL-Br was used as macroinitiator in the ATRP of DMAEMA leading to triblock copolymers with PCL as the central block and PDMAEMA sequences of different lengths. NMR and SEC analyses confirmed the formation of ABA triblocks.     

Precisely installing gold nanoparticles at the core/shell interface of micellar assemblies of triblock copolymers

Two reduction-cleavable ABA triblock copolymers possessing two disulfide linkages, PMMA-ss-PMEO₃MA-ss-PMMA and PDEA-ss-PEO-ss-PDEA were synthesized via facile substitution reactions from homopolymer precursors, where PMMA, PMEO₃MA, PDEA, and PEO represent poly(methyl methacrylate), poly(tri(ethylene glycol) monomethyl ether methacrylate, poly(2-(diethylamino)ethyl methacrylate), and poly(ethylene oxide), respectively. Spherical micelles were obtained through supramolecular self-assembly of these two triblock copolymers in aqueous solutions. The resultant micelles with abundant disulfide bonds could serve as soft templates and precisely accommodate gold nanoparticles in the core/shell interface as a result of the formation of Au-S bonds.     

Monte Carlo simulation for the adsorption of symmetric triblock copolymers I. Configuration distribution and density profiles of adsorbed chains

Monte Carlo simulations for the adsorption of symmetric triblock copolymers from a nonselective solvent at a solid-liquid interface have been performed on a lattice model. In simulations, triblock copolymer molecules are modeled as self-avoiding linear chains composed of m segments of A and n segments of B arranged as A_m/2B_nA_m/2. Either segment A or segment B is attractive, while the other is non-attractive to the surface. The microstructure of the adsorbed layers, including the segment-density profiles and the size distribution of loops, tails and trains are presented. The effect of the adsorption energy, the bulk concentration, the chain composition, as well as the chain length on various adsorption properties has been studied. The results have shown that the size distribution of various configurations is dependent of the adsorption energy, the chain composition and the chain length. The mean length of the loops, trains and tails is insensitive to the bulk concentration. The mean length of the trains increases and that of the tails decreases as the adsorption energy and the length of the attractive segments increase. The mean length of the loops for the end-adsorbed copolymers appears a maximum and that for middle-adsorbed copolymers appears a minimum as the length of attractive segments increases. The length of the non-attractive segments affects mostly the size distribution of the tails. The longer the chain is, the larger the tail appears. The mean length of the tails and loops increases linearly as the length of the non-attractive segments increases, but that of the trains approximately is unchanged.     

Nucleation and crystallization of PS-b-PEO-b-PCL triblock copolymers

We have recently prepared a series of Polystyrene-b-Poly(ethylene oxide)-b-Polycaprolactone (PS-b-PEO-b-PCL or SEOCL) triblock copolymers of varying compositions and molecular weights. These ABC triblock copolymers present the peculiarity that two of the three blocks are able to crystallize upon cooling from an already phase segregated melt. When either of the crystallizable blocks or both are a minor phase, a fractionated crystallization process develops. The confinement of crystallizable blocks in the nanoscopic scale enables the clear observation in some cases of exclusive crystallization from homogeneous nuclei of two components within the triblock copolymer. The homogeneous nature of the nucleation was deduced since the supercooling attained is the maximum possible before vitrification of the material takes place. The self-nucleation domains were also found to depend on the composition and molecular weight of the copolymers. The block copolymers exhibited a marked decrease in crystalline memory and when the crystallizable blocks constitute minor phases, the self-nucleation domain disappears. The reason behind this behavior is that only at lower self-nucleation temperatures the density of self-nuclei becomes high enough to include at least one crystal fragment per confined microdomain in view of their vast numbers (e.g., 10¹⁶/cm³).     

pH-responsive behavior of selectively quaternized diblock copolymers adsorbed at the silica/aqueous solution interface

The desorption and subsequent pH-responsive behavior of selectively quaternized poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) (PDMA-PDEA) films at the silica/aqueous solution interface has been characterized. The copolymer films were prepared at pH 9, where micelle-like surface aggregates are spontaneously formed on silica. The subsequent rinse with a copolymer-free electrolyte solution adjusted to pH 9 causes partial desorption of the weakly or non-quaternized copolymers, but negligible desorption for the highly quaternized copolymers. Further rinsing with a pH 4 electrolyte solution results in additional desorption and extension (swelling) of the remaining adsorbed copolymer film normal to the interface. This pH-responsive behavior is reversible for two pH cycles (9-4-9-4) as monitored by both quartz crystal microbalance with dissipation monitoring (QCM-D) and also zeta potential measurements. The magnitude of the pH-responsive behavior depends on the mean degree of quaternization of the PDMA block. Moreover, a combination of contact angle data, zeta potential measurements and in situ atomic force microscopy (AFM) studies indicates that the pH-responsive behavior is influenced not only by the number of cationic binding sites on the adsorbed copolymer chains but also by the adsorbed layer structure.     

Thermodynamics and rheology of cycloolefin copolymers

Cycloolefin copolymers of ethylene and norbornene, with norbornene content in the range from 36 to 62 mol %, were studied with respect to the thermal, thermodynamic, and rheological properties using differential scanning calorimetry, pressure-volume-temperature, and dynamic mechanical measurements. All copolymers obey the principle of time-temperature superposition, i.e., they can be considered as thermorheologically simple except for a temperature range in the vicinity of T(g). Despite this, the results on (i) the ratio of activation energies E(V)(*)/H(*) used to quantify the origin of the liquid-to-glass transition, (ii) the pressure coefficient of the glass temperature T(g)(P), and (iii) the dynamic fragility m suggest increasing dynamic heterogeneity with increasing norbornene content that is driven by the structural heterogeneity along the backbone.     

Synthesis and characterization of conjugated triblock copolymers

A series of conjugated triblock copolymers containing hole-transporting polycarbazole segments, electron-transporting polyoxadiazole segments, and blue-light-emitting polyfluorene segments were prepared with a two-step palladium-catalyzed Suzuki polycondensation (SPC). First dibromo-terminated polymer precursors (polyfluorenes and polyoxadiazoles) were synthesized as the central buildingblocks. Then, the dibromo-terminated polymer precursors were further polymerized with AB-type monomers [2-bromo-7-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)-9-octylcarbazole, 3-bromo-6-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)-9-octylcarbazole, and 2-bromo-7-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)-9,9-dioctylfluorene] to achieve the target triblock copolymers under SPC conditions. The formation of the triblock copolymers was confirmed by gel permeation chromatography and NMR spectroscopy. The triblock copolymers exhibited good thermal stability. An investigation of the photophysical properties indicated that efficient, photoinduced through-bond energy transfer occurred in such triblock copolymer systems. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2410–2424, 2007