Activation energy of water vapor and oxygen transmission through TiNxOy/PET gas barrier films

Titanium oxynitride (TiN_xO_y) films were deposited on polyethylene terephthalate (PET) substrates by means of a reactive radio frequency (RF) magnetron sputtering system in which the power density was the varied parameter. Experimental results show that the deposited TiN_xO_y films with a thickness of about 55 nm have similar contents of TiN, TiN_xO_y and TiO₂ bonds, although they are deposited at different power densities. The TiN_xO_y films deposited at a lower power density have fewer internal defects and grain boundaries and possess higher activation energy and a lower rate of water vapor and oxygen transmission through TiN_xO_y/PET films.     

The effects of Si3N4 interlayer on the thermal stability and hardness of Ti/TiNx (x = 0.5-1) nanolayered coatings

The polycrystalline Ti/TiN_x multilayer films were deposited by magnetron sputtering, and the as-deposited multilayer coatings were annealed at 500-800 °C for 2-4 h in vacuum. We investigated the effects of annealing temperature and annealing time on the microstructural, interfacial, and mechanical properties of the polycrystalline Ti/TiN_x multilayer films. It was found that the hardness increased with annealing temperature. This hardness enhancement was probably caused by the preferred crystalline orientation TiN(1 1 1). The X-ray reflectivity measurements showed that the layer structure of the coatings could be maintained after annealing at 500 °C and the addition of the Si₃N₄ interlayer to Ti/TiN_x multilayer could improve the thermal stability to 800 °C.     

Gas barrier properties of titanium oxynitride films deposited on polyethylene terephthalate substrates by reactive magnetron sputtering

Titanium oxynitride (TiN_xO_y) films were deposited on polyethylene terephthalate (PET) substrates by means of a reactive radio frequency (RF) magnetron sputtering system in which the power density and substrate bias were the varied parameters. Experimental results show that the deposited TiN_xO_y films exhibited an amorphous or a columnar structure with fine crystalline dependent on power density. The deposition rate increases significantly in conjunction as the power density increases from 2 W/cm² to 7 W/cm². The maximum deposition rate occurs, as the substrate bias is −40 V at a certain power densities chosen in this study. The film's roughness slightly decreases with increasing substrate bias. The TiN_xO_y films deposited at power densities above 4 W/cm² show a steady Ti:N:O ratio of about 1:1:0.8. The water vapor and oxygen transmission rates of the TiN_xO_y films reach values as low as 0.98 g/m²-day-atm and 0.60 cm³/m²-day-atm which are about 6 and 47 times lower than those of the uncoated PET substrate, respectively. These transmission rates are comparable to those of DLC, carbon-based and Al₂O₃ barrier films. Therefore, TiN_xO_y films are potential candidates to be used as a gas permeation barrier for PET substrate.     

Growth, structural and optical transport properties of nanocrystal Zn1−xCdS thin films deposited by solution growth technique (SGT) for photosensor applications

Solution Growth Technique (SGT) has been used for deposition of Zn_1−xCdS nanocrystalline thin films. Various parameters such as solution pH (10.4), deposition time, concentration of ions, composition and deposition and annealing temperatures have been optimized for the development of device grade thin film. In order to achieve uniformity and adhesiveness of thin film on glass substrate, 5 ml triethanolamine (TEA) have been added in deposition solution. The as-deposited films have been annealed in Rapid Thermal Annealing (RTA) system at various temperature ranges from 100 to 500 °C in air. The changes in structural formation and optical transport phenomena have been studied with annealing temperatures and composition value (x). As-deposited films have two phases of ZnS and CdS, which were confirmed by X-ray diffraction studies; further the X-ray analysis of annealed (380 °C) films indicates that the films have nanocrystalline size (150 nm) and crystal structure depends on the films stoichiometry and annealing temperatures. The Zn_0.4CdS films annealed at 380 °C in air for 5 min have hexagonal structure where as films annealed at 500 °C have represented the oxide phase with hexagonal structure. Optical properties of the films were studied in the wavelength range 350-1000 nm. The optical band gap (E_g=2.94-2.30 eV) decreases with the composition (x) value. The effect of air rapid annealing on the photoresponse has also been observed on Zn_1−xCdS nanocrystal thin films. The Zn_1−xCdS thin film has higher photosensitivity at higher annealing temperatures (380-500 °C), and films also have mixed Zn_1−xCdS/Zn_1−xCdSO phase with larger grain size than the as-deposited and films annealed up to 380 °C. The present results are well agreed with the results of other studies.     

Effect of Mg and Ti doping on the luminescence of Y2O3:Eu

The Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV materials (x_Eu: 0.02, x_Mg: 0.08, x_Ti: 0.04) were prepared by solid state reaction. The purity and crystal structure of the material was studied with the X-ray powder diffraction. Luminescence properties were studied in the UV-VUV range with the aid of synchrotron radiation. The emission of Y₂O₃:Eu³⁺,Mg²⁺,Ti^IV had a maximum at 612 nm (λ_exc: 250 nm) due to the ⁵D₀→⁷F₂ transition of Eu³⁺. The excitation spectra (λ_em: 612 nm) showed a broad band at 233 nm, due to the charge transfer transition between O²⁻ and Eu³⁺, and at 297 nm due to the Ti→Eu³⁺ energy transfer. Only very weak persistent luminescence was discovered. In the room and 10 K temperature excitation spectra, the line at 208 nm is due to the formation of a free exciton (FE) and a broad band at 199 nm was related to the valence-to-conduction band absorption of the Y₂O₃ host lattice. The absorption edge was ca. 205 nm giving 6.1 eV as the energy gap of Y₂O₃.     

Combinatorial synthesis and optical characterization of alloy and superlattice films based on SrTiO3 and LaAlO3

We have grown alloy and superlattice films consisting of SrTiO₃ (STO) and LaAlO₃ (LAO) by pulsed laser deposition using composition-spread technique. All the (STO)_x(LAO)_1−x (0 ≤ x ≤ 1) alloy and superlattice films exhibited a single-phase perovskite structure. The optical properties of these films were characterized by absorption spectroscopy at room temperature. The spectra show a broad absorption due to O 2p-Ti 3d(t_2g) transition in an ultraviolet region. We found that absorption edges of both alloy and superlattice films systematically shifted to higher energy with increasing LAO composition. Clear difference was observed in the composition dependence of the indirect and a direct band edges.     

Annealing effect on the structural and optical properties of a Cd1−xZnxS thin film for photovoltaic applications

Herein is a report of a study on a Cd_1−xZn_xS thin film grown on an ITO substrate using a chemical bath deposition technique. The as-deposited films were annealed in air at 400 °C for 30 min. The composition, surface morphology and structural properties of the as-deposited and annealed Cd_1−xZn_xS thin films were studied using EDX, SEM and X-ray diffraction techniques. The annealed films have been observed to possess a crystalline nature with a hexagonal structure. The optical absorption spectra were recorded within the range of 350-800 nm. The band gap of the as-deposited thin films varied from 2.46 to 2.62 eV, whereas in the annealed film these varied from 2.42 to 2.59 eV. The decreased band gap of the films after annealing was due to the improved crystalline nature of the material.     

Growth, structural and optical properties of non-stoichiometric CuIn(S1−xSex)2 thin films deposited by solution growth technique for photovoltaic application

Polycrystalline thin films of p-CuIn(S_1−xSe_x)₂ have been deposited by a solution growth technique. The deposition parameters such as pH, temperature and time have been optimized. In order to achieve uniformity of thin film, triethanolamine (TEA) has been used. As deposited films have been annealed at 450 °C in air for 5 min. The surface morphology, compositional ratio, structural properties have been studied by SEM, EDAX and XRD technique, respectively. It has been found that films have chalcopyrite structure with the lattice parameters a=5.28 Å and c=11.45 Å at composition x=0.5. The grain size of all composition x measured from SEM and XRD is varied in between 450 and 520 nm. The optical transmittance spectra have been recorded in the range 350-1000 nm. The absorption coefficient has been calculated at the absorption edge for each of the composition x and it is in the range of 10⁴ cm⁻¹. The material shows the direct allowed band gap, which varies from 1.07 to 1.44 eV with change in composition (0≤x≤1.0). These parameters are useful for the photovoltaic application.     

Laser synthesis of semiconductor nanostructures with narrow band gap

Semiconductor nanostructures with narrow band gap were synthesized by means of laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors [Fe(CO)₅] under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface. The temperature dependence of the specific conductivity of these nanostructures in the form of thin films demonstrated typical semiconductor tendency and gave the possibility to calculate the band gap for intrinsic conductivity (E_g) and the band gap assigned for impurities (E_i), which were depended upon film thickness and applied electrical field. Analysis of deposited films with scanning electron microscopy (SEM) and atomic force microscopy (AFM) demonstrated their cluster structure with average size not more than 100 nm. Semiconductor properties of deposited nanostructures were stipulated with iron oxides in different oxidized phases according to X-ray photoelectron spectroscopy (XPS) analysis.These deposited nanostructures were irradiated with Q-switched YAG laser (λ_L = 1064 nm) at power density about 6 × 10⁷ W/cm². This irradiation resulted in the crystallization process of deposited films on the Si substrate surface. The crystallization process resulted in the synthesis of iron carbide-silicide (FeSi_2−xC_x) layer with semiconductor properties too. The width of the band gap E_g of the synthesized layer of iron carbide-silicide was less than for deposited films based on iron oxides Fe₂O_3−x (0 ≤ x ≤ 1).     

Intersubband energies in Al1−yInyN/Ga1−xInxN heterostructures with lattice constant close to aGaN

We have studied the conduction band profile and the intersubband transition energy, E₁₂, of Al_1−yIn_yN/Ga_1−xIn_xN quantum well structures. We have considered how material parameters such as non-parabolicity and the uncertainty in the bowing parameter affect E₁₂ and the corresponding wavelength, λ₁₂. The calculations include strain and cover the transition range from telecommunication wavelengths (1.55 μm) to the mid-infrared (∼ 10 μm).     

Electric, thermoelectrical and photoelectric properties of CuGaxIn1−xSe2 thin films

The electrical conductivity σ, Hall effect R_H, and thermoelectric power Q of CuGa_0.25In_0.75Se₂ thin films with different growth conditions have been measured at temperature 300-520 K. These properties were also measured at room temperature for different composition of CuGa_xIn_1−xSe₂ (0.75≥x≥0) deposited at the same evaporation conditions. All investigated films are p-type over the whole temperature range. Electrical conduction was studied in order to establish its mechanism.The room temperature photoelectric response of those films were measured as a function of wavelength (2.5≥λ≥0.3) μm. It is found that the energy gap values follow a second order equation in x giving a downward bowing parameter of about 0.31 eV.     

Structural and optical properties of CuIn1−xAlxSe2 thin films prepared by four-source elemental evaporation

CuIn_1−xAl_xSe₂ (CIASe) thin films with x=0.25, 0.5 and 0.65 were prepared by four-source elemental evaporation. The structural and optical properties were investigated by X-ray diffraction, scanning electron microscopy, energy dispersive analysis, and optical transmission. The results showed that these films contain chalcopyrite structure with preferred orientation along (112) direction. The morphology, grain distribution and composition of CIASe films were studied and compared for different Al content. The optical studies revealed that the films were highly absorbing and the energy band gap calculated from transmission spectra for x=0.25, 0.5 and 0.65 were 1.2, 1.51 and 1.73 eV, respectively. The variation of Al content in the CIASe composition offered a very effective change in the optical band gap.     

Characterization of PbSe1−xTex thin films

The lead salts and their alloys are extremely interesting semiconductors due to their technological importance. The fabrication of devices with alloys of these compounds possessing detecting and lasing capabilities has been an important recent technological development. The high quality polycrystalline thin films of PbSe_1−xTe_x with variable composition (0≤x≤1) have been deposited onto ultra clean glass substrates by vacuum evaporation technique. As deposited films were annealed in vacuum at 350 K. The optical, electrical and structural properties of PbSe_1−xTe_x thin films have been examined. The optical constants (absorption coefficient and bandgap) of the films were determined by absorbance measurements in the wavelength range 2500-5000 nm using Fourier transform infrared spectrophotometer. The dc conductivity and activation energy of the films were measured in the temperature range 300-380 K. The X-ray diffraction patterns were used to determine the sample quality, crystal structure and lattice parameter of the films.     

Effects of oxygen partial pressure and substrate temperature on the structure and optical properties of MgxZn1−xO thin films prepared by magnetron sputtering

Deposited with different oxygen partial pressures and substrate temperatures, Mg_xZn_1−xO thin films were prepared using a Mg_0.6Zn_0.4O ceramic target by magnetron sputtering. The structural and optical properties of the prepared thin films were investigated. The X-ray diffraction spectra reveal that all the films on quartz substrate are grown along (2 0 0) orientation with cubic structure. The lattice constant decreases and the crystallite size increases with the increase of substrate temperature. Both energy dispersive X-ray spectroscopy and calculated results suggest the ratio of Mg/Zn increases with increasing substrate temperature. The thin film deposited with T_s = 500 °C has a minimal rms roughness of 7.37 nm. The transmittance of all the films is higher than 85% in the visual region. The optical band gap is not sensitive to the oxygen partial pressure, while it increases from 5.63 eV for T_s = 100 °C to 5.95 eV for T_s = 700 °C. In addition, the refractive indices calculated from transmission spectra are sensitive to the substrate temperature. The photoluminescence spectra of Mg_xZn_1−xO thin films excited by 330 nm ultraviolet light indicate that the peak intensity of the spectra is influenced by the oxygen partial pressure and substrate temperature.     

Femtosecond Z-scan measurement of third-order optical nonlinearities in anatase TiO2 thin films

Anatase phase TiO₂ films have been grown on fused silica substrate by pulsed laser deposition technique at substrate temperature of 750 °C under the oxygen pressure of 5 Pa. From the transmission spectra, the optical band gap and linear refractive index of the TiO₂ films were determined. The third-order optical nonlinearities of the films were measured by Z-scan method using a femtosecond laser (50 fs) at the wavelength of 800 nm. The real and imaginary parts of third-order nonlinear susceptibility χ⁽³⁾ were determined to be −7.1 × 10⁻¹¹esu and −4.42 × 10⁻¹²esu, respectively. The figure of merit, T, defined by T=βλ/n₂, was calculated to be 0.8, which meets the requirement of all-optical switching devices. The results show that the anatase TiO₂ films have great potential applications for nonlinear optical devices.     

Particulate assisted growth of ZnO nanorods and microrods by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on the gallium nitride (GaN) and sapphire (Al₂O₃) substrates by pulsed laser deposition (PLD) without using any metal catalyst. The experiment was carried out at three different laser wavelengths of Nd:YAG laser (λ = 1064 nm, λ = 532 nm) and KrF excimer laser (λ = 248 nm). The ZnO films grown at λ = 532 nm revealed the presence of ZnO nanorods and microrods. The diameter of the rods varies from 250 nm to 2 μm and the length varies between 9 and 22 μm. The scanning electron microscopy (SEM) images of the rods revealed the absence of frozen balls at the tip of the ZnO rods. The growth of ZnO rods has been explained by vapor-solid (V-S) mechanism. The origin of growth of ZnO rods has been attributed to the ejection of micrometric and sub-micrometric sized particulates from the ZnO target. The ZnO films grown at λ = 1064 nm and λ = 248 nm do not show the rod like morphology. X-ray photoelectron spectroscopy (XPS) has not shown the presence of any impurity except zinc and oxygen.     

Optical band gap of zinc nitride films prepared on quartz substrates from a zinc nitride target by reactive rf magnetron sputtering

Polycrystalline zinc nitride films have been synthesized onto quartz substrates from the zinc nitride target and the nitrogen working gas by reactive rf magnetron sputtering at room temperature. X-ray diffraction study indicates that polycrystalline zinc nitride films are of cubic structure with the lattice constant a = 0.979(1) nm and have preferred orientations with (3 2 1) and (4 4 2). Its absorption coefficients as well as the film thickness are calculated from the transmission spectra, which are measured with a double beam spectrophotometer. The optical band gap has been determined from the photon energy dependence of absorption coefficient, an indirect transition optical band gap of 2.12(3) eV has been obtained.     

Structural and magnetic properties of sol-gel Co2xNi0.5−x Zn0.5−xFe2O4 thin films

Nanocrystalline Co_2xNi_0.5−xZn_0.5−xFe₂O₄ (x=0−0.5) thin films have been synthesized with various grain sizes by a sol-gel method on polycrystalline silicon substrates. The morphology as well as magnetic and microwave absorption properties of the films calcined at 1073 K were studied using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and vibrating sample magnetometry. All films were uniform without microcracks. The Co content in the Co-Ni-Zn films resulted in a grain size ranging from 15 to 32 nm while it ranged from 33 to 49 nm in the corresponding powders. Saturation and remnant magnetization increased with increase in grain size, while coercivity demonstrated a drop due to multidomain behavior of crystallites for a given value of x. Saturation magnetization increased and remnant magnetization had a maximum as a function of grain size independent of x. In turn, coercivity increased with x independent of grain size. Complex permittivity of the Co-Ni-Zn ferrite films was measured in the frequency range 2-15 GHz. The highest hysteretic heating rate in the temperature range 315-355 K was observed in CoFe₂O₄. The maximum absorption band shifted from 13 to 11 GHz as cobalt content increased from x=0.1 to 0.2.     

Optical properties of Ge-As-Te thin films

Different compositions of Ge_xAs₁₀Te_90−x (x=5, 10, 15, 20, and 25 at%) chalcogenide glasses were prepared by the usual melt quench technique. Amorphous Ge_xAs₁₀Te_90−x thin films were deposited onto cleaned glass substrates using the thermal evaporation method. Transmission spectra, T(λ), of the films at normal incidence were measured in the wavelength range 400-2500 nm. A straightforward analysis proposed by Swanepoel based on the use of the maxima and minima of the interference fringes has been used to drive the film thickness, d, the complex index of refraction, n, and the extinction coefficient, k. It was found that, the addition of Ge content at the expense of Te atoms shifts the optical band gap to the short wavelength side (blue shift of the optical band gap) while the refractive index are found to decreases. The obtained results of the refractive index were discussed in terms of the electronic polarizability and the single-oscillator Wemple and DiDomenico model (WDD). The optical absorption is due to the allowed non-direct optical transitions. The observed increase in the optical band gap with the increase in Ge content was discussed in terms of the width of the tail states in the gap and the covalent bond approach.     

Microstructure and nanohardness of the diluted magnetic semiconducting Cd1−xMnxS nano-crystalline films

Cd_1−xMn_xS nano-crystalline films (0 ≤ x ≤ 0.5) were formed on glass substrates by thermal evaporation technique at room temperature (300 K). AFM studies showed that all the films were in nano-crystalline form with the grain size varying in the range between 36 and 58 nm and exhibited hexagonal structure of the host material. The lattice parameters varied linearly with composition, following Vegard's law in the entire composition range. The nanohardness and Young's modulus decreased sharply with ‘Mn’ content upto x = 0.3 and increased with high Mn content.