Structural properties of oxygen on InN(0 0 0 1) surface

First-principles calculations are performed to study the various structures of oxygen (O) adsorbed on InN(0 0 0 1) surfaces. It is found that the formation energy of O on InN(0 0 0 1) decreases with decreasing oxygen coverage. Of all the adsorbate induced surface structures examined, the structure of InN(0 0 0 1)-(2 × 2) as caused by O adsorption at the H₃ sites with 0.25 monolayers coverage is most energetically favorable. Meanwhile, nitrogen (N) vacancy can form spontaneously. Oxygen atoms may also substitute N atoms, or accumulate at the voids inside InN film or simply stay on the surface during growth. The oxygen impurity then acts as a potential source for the n-type conductivity of InN as well as the large energy band gap measured.     

The adsorption of In on the surface of (0 0 1) CdTe

To understand CdTe doping with In, first-principle calculations are performed to obtain the various kinds of surface-structure for In on CdTe (0 0 1) surface. Of all the structures examined, the structure of CdTe (0 0 1) as caused by In adsorption atoms at the fourfold hollow sites with 0.25 monolayer coverage is the most energetically favorable. In atoms are adsorbed on the Cd-terminated surface, whereas below the Te-terminated surface. For the Cd-terminated surface, cadmium vacancy can form spontaneously and is energetically favorable. In atoms are likely to be adsorbed/incorporated at an interstitial site on Te-terminated CdTe (0 0 1) surfaces for most of the range of the chemical potential.     

Adsorption of gold on hydrogen terminated Si(0 0 1): Formation of chain structure

Possible formation of stable Au atomic wire on the hydrogen terminated Si(0 0 1): 3×1 surface is investigated under the density functional formalism. The hydrogen terminated Si(0 0 1): 3×1 surface is patterned in two different ways by removing selective hydrogen atoms from the surface. The adsorption of Au on such surfaces is studied at different sub-monolayer coverages. At 4/9 monolayer (ML) coverage, zigzag continuous Au chains are found to be stable on the patterned hydrogen terminated Si(0 0 1): 3×1 surface. The reason for the stability of the wire structures at 4/9 ML coverage is explained. It is to be noted that beyond 4/9 ML coverage, the additional Au atoms may introduce clusters on the surface. The continuous atomic gold chains on the substrate may be useful for the fabrication of atomic scale devices.     

Theoretical study of Ti and Fe surface alloys on Al(0 0 1) substrate

Accurate density-functional calculations are performed to investigate the formation of Ti and Fe ultrathin alloys on Al(0 0 1) surface. It is demonstrated that a deposition of Ti monolayer on Al(0 0 1) substrate leads to the formation of Al₃Ti surface alloy with Ti atoms arranged according to the L1₂ stacking, distinct from the D0₂₂ structure characteristic of a bulk Al₃Ti compound. A quest for the reason of this distinct atomic arrangement led us to the study of the surface structure of Al₃Ti(0 0 1) compound. It is concluded that even the Al₃Ti(0 0 1) surface is terminated with three layers assuming a L1₂ stacking and hence this stacking fault can be classified as a surface-induced stacking fault. Several possibilities of Fe atoms distributed in the surface region of Al(0 0 1) have been examined. The most stable configuration is the one with the compact Fe monolayer on Al(0 0 1) and covered by one Al monolayer. Lastly, our calculations show that there is no barrier for the penetration of Fe adatoms below the Al(0 0 1) surface; however, such a barrier is present for a Ti-alloyed Al(0 0 1) surface.     

Interdiffusion of adsorbed Pb and Bi on Cu(1 0 0)

The impingement and interdiffusion of adsorbed Pb and Bi layers spreading from separated 3D pure bulk sources on Cu(1 0 0) has been studied, at T = 513 K, by in situ scanning Auger microscopy. When the leading edges of the pure Pb and Bi diffusion profiles impinge, they both consist of low-coverage lattice gas surface alloyed phases. In these low-coverage phases, Pb displaces surface alloyed Bi and the point of intersection of the profiles drifts towards the Bi source. These features lead to the conclusion that Pb atoms are more strongly bound at surface alloyed sites in Cu(1 0 0) than Bi atoms. Once the total coverage (Pb + Bi) on the substrate reaches about one monolayer, Pb and Bi are dealloyed from the substrate, and the interdiffusion profiles become essentially symmetric. Pb and Bi mix in all proportions, with an interdiffusion coefficient of ∼10⁻¹³ m²/s. This is considerably smaller than the self-diffusion coefficients previously observed for pure Pb and Bi in their respective high-coverage phases, indicating that the mechanism of interdiffusion is different from that of self-diffusion. As interdiffusion proceeds, the point of intersection of the Pb and Bi profiles reverses its drift direction, leading to the conclusion that binding of Bi atoms to the Cu(1 0 0) substrate is stronger than that of Pb atoms in the highest-coverage surface dealloyed layers.     

Theoretical study of CO and Pb adsorption on the Ni(1 1 1) and Ni3Al(1 1 1) surfaces

Adsorption of CO molecules and Pb atoms on the Ni(1 1 1) and Ni₃Al(1 1 1) substrates is studied theoretically within an ab initio density-functional-theory approach. Stable adsorption sites and the corresponding adsorption energies are first determined for stoichiometric surfaces. The three-fold hollow sites (fcc for Pb and hcp for CO) are found most favourable on both substrates. Next, the effect of surface alloying by a substitution of selected topmost substrate atoms by Pb or Ni atoms on the adsorption characteristics is investigated. When the surface Al atoms of the Ni₃Al(1 1 1) substrate are replaced by Ni atoms, the Pb and CO adsorption energies approach those for a pure Ni(1 1 1) substrate. The Pb alloying has a more substantial effect. On the Ni₃Al(1 1 1) substrate, it reduces considerably adsorption energy of CO. On the Ni(1 1 1) substrate, CO binding strengthens slightly upon the formation of the Ni(1 1 1)p(2×2)-Pb surface alloy, whereas it weakens drastically when the Ni(1 1 1)-Pb surface alloy is formed.     

Interaction of CO with atomically well-defined PtxRuy/Ru(0 0 0 1) surface alloys

The interaction of CO with structurally well-defined Pt_xRu_y surface alloys supported on Ru(0 0 0 1) was investigated by thermal desorption spectroscopy and infrared reflection-absorption spectroscopy. The surface composition and the distribution of the surface atoms were controlled by high resolution scanning tunneling microscopy. On these surfaces, which have a nearly random distribution of the two surface species, the adsorption (and desorption) of CO is strongly modified compared to the pure elemental surfaces, by strain effects and electronic ligand effects. CO adsorbs exclusively in a linear configuration on Pt and Ru atoms for all surfaces investigated. The adsorption energy of CO is lowered on the alloy surfaces with respect to both Pt(1 1 1) and Ru(0 0 0 1), similar as for pseudomorphic monolayer Pt films. For both Pt and Ru sites the adsorption strength decreases with increasing Pt concentration.     

Spectroscopic interpretation for Na-induced phase transitions on Na/Si(1 1 1)3 × 1

Na adsorption at room temperature causes the Na/Si(1 1 1)3 × 1 surface with Na coverage of 1/3 monolayer (ML) to transit into the Na/Si(1 1 1)6 × 1 surface at 1/2 ML and sequentially into the Na/Si(1 1 1)3 × 1 surface at 2/3 ML. The phase transition was studied by Si 2p core-level photoemission spectroscopy. The detailed line shape analysis of the Si 2p core-level spectrum of the Na/Si(1 1 1)3 × 1 surface (2/3 ML) is presented and compared to the Na/Si(1 1 1)3 × 1 surface (1/3 ML) which is composed of Si honeycomb chain-channel structures. This suggests that as additional Na atoms form atomic chains resulting in the Na/Si(1 1 1)3 × 1 surface (2/3 ML), the inner atoms of the Si honeycomb chain-channel structure is buckled due to the additional Na atoms.     

Enhanced reactivity and selectivity in oxidation of Cu(1 0 0) and α-Cu-Al(5 at.%)(1 0 0) surfaces studied by electron and ion spectroscopies

In this study we investigate the influence of alloying on the reactivity and bonding of oxygen on α-Cu-Al(5 at.%)(1 0 0) oriented single crystal surfaces by X-ray photoelectron spectroscopy (XPS), ultra-violet spectroscopy (UPS) and low energy ion scattering (LEIS) spectroscopy, at room temperature. It was found that alloying results in an enhanced reactivity of both Cu and Al sites in comparison with the pure metals. According to adsorption curves calculated from XPS, saturation of the alloy surface occurs for exposures of ∼15 L. At saturation the total amount of adsorbed oxygen is similar for the alloy and pure copper surfaces. It was determined that first mostly Al sites are oxidized, followed by simultaneous oxidation of Cu and Al sites. At saturation the amount of oxygen bonded to Cu sites is ∼1.7 larger then that bonded to Al sites. From a comparison of the XPS and LEIS data analysis as a function of oxygen exposure it was found that oxidation of α-Cu-Al(5 at.%)(1 0 0) alloy is a multi-stage process with fast and slow stages. These stages involve an interplay of chemisorption, sub-surface diffusion of oxygen and Al segregation. UPS measurements show an increase in the work function of the alloy surface with oxygen adsorption. This is a contrast to pure Cu surfaces where the work function decreases at the initial stages of oxidation followed by an increase with oxygen exposure. Annealing to 400 °C drives the oxidized alloy surface into its thermodynamic state resulting in the formation of an aluminum oxide layer. Possible mechanisms to explain the enhanced reactivity of the alloy surface compared to that of pure copper are suggested and discussed.     

Formation, stability and CO adsorption properties of PdAg/Pd(1 1 1) surface alloys

The formation, stability and CO adsorption properties of PdAg/Pd(1 1 1) surface alloys were investigated by X-ray photoelectron spectroscopy (XPS) and by adsorption of CO probe molecules, which was characterized by temperature-programmed desorption (TPD) and high resolution electron energy loss spectroscopy (HREELS). The PdAg/Pd(1 1 1) surface alloys were prepared by annealing (partly) Ag film covered Pd(1 1 1) surfaces, where the Ag films were deposited at room temperature. Surface alloy formation leads to a modification of the electronic properties, evidenced by core-level shifts (CLSs) of both the Pd(3d) and Ag(3d) signal, with the extent of the CLSs depending on both initial Ag coverage and annealing temperature. The role of Ag pre-coverage and annealing temperature on surface alloy formation is elucidated. For a monolayer Ag covered Pd(1 1 1) surface, surface alloy formation starts at ∼450 K, and the resulting surface alloy is stable upon annealing at temperatures between 600 and 800 K. CO TPD and HREELS measurements demonstrate that at 120 K CO is exclusively adsorbed on Pd surface atoms/Pd sites of the bimetallic surfaces, and that the CO adsorption behavior is dominated by geometric ensemble effects, with adsorption on threefold hollow Pd₃ sites being more stable than on Pd₂ bridge sites and finally Pd₁ a-top sites.     

Growth of Ce on Rh(1 1 1)

We have studied the growth of cerium films on Rh(1 1 1) using STM (scanning tunneling microscopy), LEED (low energy electron diffraction), XPS (X-ray photoelectron spectroscopy) and AES (Auger electron spectroscopy). Measurements of the Ce films after room temperature deposition showed that Ce is initially forming nanoclusters in the low coverage regime. These clusters consist of 12 Ce atoms and have the shape of pinwheels. At a coverage of 0.25 ML (monolayer, ML) an adatom layer with a (2 × 2) superstructure is observed. Above 0.4 ML, Rh is diffusing through pinholes into the film, forming an unstructured mixed layer. Annealing at 250 °C leads to the formation of ordered Ce-Rh compounds based on the bulk compound CeRh₃. At a coverage of 0.1 ML, small ordered (2 × 2) surface alloy domains are observed. The exchanged Rh atoms form additional alloy islands situated on the pure Rh(1 1 1) surface, showing the same (2 × 2) superstructure as the surface alloy. At a coverage of 0.25 ML, the surface is completely covered by the surface alloy and alloy islands. The (2 × 2) structure is equivalent to a (1 1 1)-plane of CeRh₃, contracted by 6%. Annealing a 1 ML thick Ce layer leads to a flat surface consisting of different rotational domains of CeRh₃(1 0 0). The Rh needed for alloy formation comes from 50 Å deep pits in the substrate. Finally we show that LEIS (low energy ion scattering) is not suitable for the characterization of Ce and CeRh films due to strong effects of neutralization.     

Theoretical study of oxygen adsorption at the Fe(1 1 0) and (1 0 0) surfaces

Electronic, magnetic and structural properties of atomic oxygen adsorbed in on-surface and subsurface sites at the two most densely packed iron surfaces are investigated using density functional theory combined with a thermodynamics formalism. Oxygen coverages varying from a quarter to two monolayers (MLs) are considered. At a 1/4 ML coverage, the most stable on-surface adsorption sites are the twofold long bridge sites on the (1 1 0), and the fourfold-hollow sites on the (1 0 0) surface. The presence of on-surface oxygen atoms enhances the magnetic moments of the atoms of the two topmost Fe layers. Detailed results on the surface magnetic properties, due to O incorporation, are presented as well. Subsurface adsorption is found unfavored. The most stable subsurface O, in tetrahedral positions at the (1 0 0) and octahedral ones at the (1 1 0) surface, are characterized by substantially lower binding than that in the on-surface sites. Subsurface oxygen increases the interplanar distance between the uppermost Fe layers. The preadsorbed oxygen overlayer enhances binding of subsurface O atoms, particularly for tetrahedral sites beneath the (1 1 0) surface.     

Hexaphenyl thin films on clean and carbon covered Au(1 1 1) studied with TDS and LEED

The adsorption and growth of ordered para-hexaphenyl (6P) films have been investigated both on clean and partially carbon pre-covered Au(1 1 1) single crystal surfaces by thermal desorption spectroscopy (TDS) and low energy electron diffraction (LEED) under ultra-high vacuum conditions. The existence of a distinct first and second monomolecular 6P layer that clearly separate from the multilayer regime, which comprise lying molecules with respect to the substrate surface, could be inferred from TDS. For both the 6P mono- and multilayer grown on pure Au(1 1 1) the desorption energies have been determined based on experimental TDS data. In particular, for the monolayer regime a coverage dependence of the desorption energy has been found, which is attributed to repulsive interactions between neighbouring 6P molecules adsorbed on the gold surface. The existence of well-ordered film structures could be inferred from LEED for half monolayer and full monolayer thick 6P films. Based on the LEED and TDS data, structural models are presented for these highly ordered organic films. Multi-step dehydrogenation of 6P molecules adsorbed on clean Au(1 1 1) surfaces is reported for temperatures above 650 K together with experimental evidence for the existence of a regular overlayer composed of partially dehydrogenated polycyclic aromatic hydrocarbon (PAH) intermediates. A quite different adsorption/desorption kinetics and film growth has been observed for 6P films grown on carbon pre-covered Au(1 1 1) surfaces.     

Self-assembled germanium nano-clusters on silver(1 1 0)

The adsorption of germanium on Ag(1 1 0) has been investigated by scanning tunnelling microscopy (STM), as well as surface X-ray diffraction (SXRD). At 0.5 germanium monolayer (ML) coverage, Low Energy Electron Diffraction (LEED) patterns reveals a sharp c(4 × 2) superstructure. Based on STM images and SXRD measurements, we present an atomic model of the surface structure with Ge atoms forming tetramer nano-clusters perfectly assembled in a two-dimensional array over the silver top layer. The adsorption of the germanium atoms induces a weak perturbation of the Ag surface. Upon comparison with results obtained on the (1 1 1) and (1 0 0) faces, we stress the role played by the relative interactions between silver and germanium on the observed surface structures.     

Vibrationally-assisted dissociative adsorption of oxygen on Ru(0 0 0 1)-p(2 × 1)-O

Supersonic molecular beam technique combined with high resolution X-ray photoelectron spectroscopy using synchrotron radiation was applied to the study of the dynamics of dissociative adsorption of oxygen on Ru(0 0 0 1) surface in high coverage region. The Ru(0 0 0 1) surface pre-covered with oxygen atoms of 0.5 monolayer, which corresponds to the p(2 × 1)-O structure, was dosed to oxygen molecules with translational energy of 0.5 eV. Oxygen uptake was compared between the cases with and without the beam source heated in order to verify the effects of internal energy of oxygen. We found drastic enhancement in initial sticking probability of oxygen when the beam source was heated to 1400 K. We concluded that the enhancement of sticking probability is mainly caused by molecular vibrational excitation, indicating that dissociation barrier is located in the exit channel on potential energy surface.     

Surface segregation of aluminum atoms on Cu-9 at.% Al(1 1 1) studied by Auger electron spectroscopy and low energy electron diffraction

Auger electron spectroscopy (AES) and low energy electron diffraction (LEED) were applied to investigate the segregation of aluminum atoms on a Cu-9 at.% Al(1 1 1) surface. We observed that the Al concentration in the top layer ranged between about 9 and 36 at.% after the sample we used was annealed at different temperatures. The phenomenon of Al atoms segregating on the surfaces was explained well by considering the diffusion length of Al atoms in bulk Cu. LEED measurements showed that R30° structures grew as the concentration of Al atoms increased. The segregation phenomena on surfaces resulted in a stable two-dimensional Cu₆₇Al₃₃ alloy phase in the top layer.     

A theoretical study of hydrogen adsorption and diffusion on a W(1 1 0) surface

We have used density functional theory to investigate hydrogen adsorption and diffusion on a W(1 1 0) surface. Hydrogen adsorption structures were examined from low coverage to one monolayer, and a threefold hollow site was found to be the most stable site at all coverages. In contrast to previous assertions, the work function decrease is not due to electron transfer from the hydrogen atoms to the W surface, but due to electron depletion at the vacuum region above the hydrogen atoms. Hydrogen atoms can diffuse via short-bridge sites and long-bridge sites at a coverage of θ = 1.0. Although the calculated activation energy for hydrogen diffusion via a short-bridge site is as small as 0.05 eV, field emission microscope experiments have shown that the activation energy for hydrogen diffusion is about 0.20 eV, which agrees fairly well with our calculated value of the activation energy via a long-bridge site. This discrepancy can be related to hydrogen delocalization on the W(1 1 0) surface, which has been suggested by electron energy loss spectroscopy experiments.     

On-surface and sub-surface oxygen on ideal and reconstructed Cu(1 0 0)

In order to understand the first steps of the Cu(1 0 0) oxidation we performed first principles calculations for on-surface and sub-surface oxygen on this surface. According to our calculations, the adsorption energies for all on-surface site oxygen atoms increase, whereas the energies of the sub-surface atoms decrease with the increasing oxygen coverage. At coverage 1 ML and higher on the reconstructed surface, structures including both on- and sub-surface atoms are energetically more favourable than structures consisting only of on-surface adsorbates. On the ideal (1 0 0) surface this change can be perceived at coverage 0.75 ML.     

Hydrogen adsorption and diffusion on Pd(1 1 1)

The adsorption, diffusion and ordering of hydrogen on Pd(1 1 1) was studied by scanning tunneling microscopy in the temperature range of 37-90 K. At low coverage isolated hydrogen atoms were observed. They formed √3×√3-1H islands as the coverage increased. Above 1/3 monolayer (ML) coverage areas of a new phase with √3×√3-2H structure were formed, with both structures coexisting between 1/3 and 2/3 ML. Finally a 1 × 1 structure was formed after high exposures of hydrogen above 50 K, with a coverage close to 1 ML. Atomically resolved images reveal that H binds to fcc hollow sites.     

First-principles calculations of ethanethiol adsorption and decomposition on GaN (0 0 0 1) surface

The adsorption and decomposition of ethanethiol on GaN (0 0 0 1) surface have been investigated with first-principles calculations. The DFT calculations reveal that ethanethiol adsorbs dissociatively on the clean GaN (0 0 0 1) surface to form ethanethiolate and hydrogen species. An up limit coverage of 0.33 for ethanethiolate monolayer on GaN (0 0 0 1) surface is obtained and the position of the sulfur atom and the tilt angle of the thiolate chain are found to be very sensitive to the surface coverage. Furthermore, the reactivity of ethanethiol adsorption and further thermal decomposition reactions on GaN (0 0 0 1) surface is discussed by calculating the possible reaction pathways and ethene is found to be the major product.