Rutile TiO2 nano-branched arrays on FTO for dye-sensitized solar cells

Hierarchical TiO(2) nanostructures would be desirable for preparing dye-sensitized solar cells because of their large amount of dye adsorption and superior light harvesting efficiency, as well as efficient charge separation and transport properties. In this study, rutile TiO(2) nano-branched arrays grown directly on transparent conductive glass (FTO) were prepared by a facile two-step wet chemical synthesis process, using a simple aqueous chemical growth method involving immersing the TiO(2) nanorod arrays in an aqueous TiCl(4) solution as seeds, which were prepared by a hydrothermal method. The dye-sensitized solar cells based on the TiO(2) nano-branched arrays which were only about 3 μm in length show a short-circuit current intensity of 10.05 mA cm(-2) and a light-to-electricity conversion efficiency of 3.75%, which is nearly three times as high as that of bare nanorod arrays, due to the preferable nanostructure, which not only retains the efficient charge separation and transport properties of the nanorod arrays, but also can improve the amount of dye adsorption due to the increased specific surface area from the nanobranches.     

Effect of TiO2 crystalline phase composition on the physicochemical and catalytic properties of Pd/TiO(2) in selective acetylene hydrogenation

Pd/TiO(2) catalysts have been prepared using TiO(2) supports consisting of various rutile/anatase crystalline phase compositions. Increasing percentages of rutile phase in the TiO(2) resulted in a decrease in Brunauer-Emmett-Teller surface areas, fewer Ti(3+) sites, and lower Pd dispersion. While acetylene conversions were found to be merely dependent on Pd dispersion, ethylene selectivity appeared to be strongly affected by the presence of Ti(3+) in the TiO(2) samples. When TiO(2) samples with 0-44% rutile were used, high ethylene selectivities (58-93%) were obtained whereas ethylene losses occurred for those supported on TiO(2) with 85% or 100% rutile phase. X-ray photoelectron spectroscopy and electron spin resonance experiments revealed that a significant amount of Ti(3+) existed in the TiO(2) samples composed of 0-44% rutile. The presence of Ti(3+) in contact with Pd can probably lower the adsorption strength of ethylene resulting in an ethylene gain. Among the five catalysts used in this study, the results for Pd/TiO(2)-R44 suggest an optimum anatase/rutile composition of the TiO(2) used to obtain high selectivity of ethylene in selective acetylene hydrogenation.     

Simultaneous phase- and size-controlled synthesis of TiO(2) nanorods via non-hydrolytic sol-gel reaction of syringe pump delivered precursors

The simultaneous phase- and size-controlled synthesis of TiO(2) nanorods was achieved via the non-hydrolytic sol-gel reaction of continuously delivered two titanium precursors using two separate syringe pumps. As the injection rate was decreased, the length of the TiO(2) nanorods was increased and their crystalline phase was simultaneously transformed from anatase to rutile. When the reaction was performed by injecting titanium precursors contained in two separate syringes into a hot oleylamine surfactant solution with an injection rate of 30 mL/h, anatase TiO(2) nanorods with dimensions of 6 nm (thickness) x 50 nm (length) were produced. When the injection rate was decreased to 2.5 mL/h, star-shaped rutile TiO(2) nanorods with dimensions of 25 nm x 200 nm and a small fraction of rod-shaped anatase TiO(2) nanorods with dimensions of 9 nm x 100 nm were synthesized. Pure star-shaped rutile TiO(2) nanorods with dimensions of 25 nm x 450 nm were synthesized when the injection rate was further decreased to 1.25 mL/h. The simultaneous phase transformation and length elongation of the TiO(2) nanorods were achieved. Under optimized reaction conditions, as much as 3.5 g of TiO(2) nanorods were produced. The TiO(2) nanorods were used to produce dye-sensitized solar cells, and the photoconversion efficiency of the mixture composed of star-shaped rutile TiO(2) nanorods and a small fraction of anatase nanorods were comparable to that of Degussa P-25.     

N掺杂纳米TiO2可见光催化氧化丙烯的动力学行为

通过在不同温度的氨气气氛中处理纳米管钛酸(NTA)制得具有可见光响应的氮掺杂纳米二氧化钛. X射线衍射(XRD)谱表征结果显示, 当温度高于400 ℃时, 样品由正交晶系向锐钛矿相转变, 700 ℃处理得到的样品除了锐钛矿相TiO2外还有TiN 新相存在; 紫外-可见扩散漫反射(DRS)结果表明, 氮掺杂纳米TiO2在整个可见光区都有明显的吸收. 不同波长可见光及不同气体流速的光催化氧化丙烯动力学研究表明, 活性最好的N掺杂纳米TiO2催化剂(600 ℃ NH3处理)对可见光的利用范围可扩展至500 nm, 低浓度丙烯光催化氧化反应为一级反应.     

Highly efficient dye-sensitized solar cells with a titania thin-film electrode composed of a network structure of single-crystal-like TiO2 nanowires made by the "oriented attachment" mechanism

In this study, single-crystal-like anatase TiO(2) nanowires were formed in a network structure by surfactant-assisted self-assembling processes at low temperature. The crystal lattice planes of the nanowires and networks of such wires composed of many nanoparticles were almost perfectly aligned with each other due to the "oriented attachment" mechanism, resulting in the high rate of electron transfer through the TiO(2) nanonetwork with single-crystal-like anatase nanowires. The direction of crystal growth of oriented attachment was controlled by changing the mole ratio of acetylacetone to Ti, that is, regulating both the adsorption of surfactant molecules via control of the reaction rate and the surface energy. A single-crystalline anatase exposing mainly the [101] plane has been prepared, which adsorbed ruthenium dye over 4 times higher as compared to P-25. A high light-to-electricity conversion yield of 9.3% was achieved by applying the titania nanomaterials with network structure as the titania thin film of dye-sensitized solar cells.     

Large-scale synthesis of TiO2 nanorods via nonhydrolytic sol-gel ester elimination reaction and their application to photocatalytic inactivation of E. coli

A simple method of synthesizing a large quantity of TiO(2) nanorods was developed. A nonhydrolytic sol-gel reaction between titanium(IV) isopropoxide and oleic acid at 270 degrees C generated 3.4 nm (diameter) x 38 nm (length) sized TiO(2) nanocrystals. The transmission electron microscopic image showed that the particles have a uniform diameter distribution. X-ray diffraction and selected-area electron diffraction patterns combined with high-resolution transmission electron microscopic image showed that the TiO(2) nanorods are highly crystalline anatase crystal structure grown along the [001] direction. The diameters of the TiO(2) nanorods were controlled by adding 1-hexadecylamine to the reaction mixture as a cosurfactant. TiO(2) nanorods with average sizes of 2.7 nm x 28 nm, 2.2 nm x 32 nm, and 2.0 nm x 39 nm were obtained using 1, 5, and 10 mmol of 1-hexadecylamine, respectively. The optical absorption spectrum of the TiO(2) nanorods exhibited that the band gap of the nanorods was 3.33 eV at room temperature, which is 130 meV larger than that of bulk anatase (3.2 eV), demonstrating the quantum confinement effect. Oleic acid coordinated on the nanorod surface was removed by the reduction of the carboxyl group of oleic acid, and the Brunauer-Emmett-Teller surface area of the resulting naked TiO(2) nanorods was 198 m(2)/g. The naked TiO(2) nanorods exhibited higher photocatalytic activity than the P-25 photocatalyst for the photocatalytic inactivation of E. coli.     

Synthesis and characterization of ultrahigh crystalline TiO2 nanotubes

Ultrahigh crystalline TiO2 nanotubes were synthesized by hydrogen peroxide treatment of very low crystalline titania nanotubes (TiNT-as prepared), which were prepared with synthesized TiO2 nanoparticles by hydrothermal methods in an aqueous NaOH solution. Thus, prepared ultrahigh crystalline TiO2 nanotubes (TiNT-H2O2) showed comparable crystallinity with high crystalline TiO2 nanoparticles. The details of nanotubular structures were elucidated by high resolution-transmission electron microscopy (HR-TEM), field emission-scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis in transmission electron microscopy (TEM-EDX), X-ray diffraction (XRD), photoluminescence (PL), and BET surface area. TiNT-H2O2 was found to be a multiwalled anatase phase only with an average outer diameter of approximately 8 nm and an inner diameter of approximately 5 nm and grown along the [001] direction to 500-700 nm long with an interlayer fringe distance of ca. 0.78 nm. The photocatalytic activity of TiNT-H2O2 was about 2-fold higher than those of TiNT-as prepared, synthesized TiO2 nanoparticles, and TiO2-P25 (Degussa) in the photocatalytic oxidation of trimethylamine gas under UV irradiation.     

Synthesis of anatase TiO2 rods with dominant reactive {010} facets for the photoreduction of CO2 to CH4 and use in dye-sensitized solar cells

Single crystalline anatase TiO(2) rods with dominant reactive {010} facets are directly synthesized by hydrothermally treating Cs(0.68)Ti(1.83)O(4)/H(0.68)Ti(1.83)O(4) particles. The nanosized rods show a comparable conversion efficiency in dye-sensitized solar cells (DSSCs), and a superior photocatalytic conversion of CO(2) into methane to the benchmark P25 TiO(2) nanocrystals.     

Ordered mesoporous silica with large cage-like pores: structural identification and pore connectivity design by controlling the synthesis temperature and time

FDU-1 silicas with large cage-like pores (diameter about 10 nm) were synthesized under acidic conditions from tetraethyl orthosilicate in the presence of a poly(ethylene oxide)-poly(butylene oxide)-poly(ethylene oxide) triblock copolymer template B50-6600 (EO(39)BO(47)EO(39)). High-resolution transmission electron microscopy and small-angle X-ray scattering provided strong evidence that FDU-1 silica synthesized under typical conditions is a face-centered cubic Fm3m structure with 3-dimensional hexagonal intergrowth and is not a body-centered cubic Im3m structure, as originally reported. Samples synthesized in a wide range of conditions (initial temperatures from 298 to 353 K; hydrothermal treatment at 333-393 K) exhibited similar XRD patterns and their nitrogen adsorption isotherms indicated a good-quality cage-like pore structure. The examination of low-pressure nitrogen adsorption isotherms for FDU-1 samples, whose pore entrance diameters were evaluated using an independent method, allowed us to conclude that low-pressure adsorption was appreciably stronger for samples with smaller pore entrance sizes. This prompted us to examine low-pressure adsorption isotherms for a wide range of samples and led us to a conclusion that the FDU-1 pore entrance size can be systematically enlarged from about 1.3 nm (perhaps even lower) to at least 2.4 nm without an appreciable loss of uniformity by increasing the temperature of the hydrothermal treatment or the initial synthesis. Further enlargement of pore entrance size was achieved for sufficiently long hydrothermal treatment times at temperatures of 373 K or higher, as seen from the shape of nitrogen desorption isotherms. This allowed us to obtain samples with uniform pore sizes, high adsorption capacity, and with pore entrances enlarged so much that their size was similar to the size of the pore itself, resulting in a highly open porous structure. However, in the latter case, there was evidence that the pore entrance size distribution was quite broad.     

Real time observation of the hydrothermal crystallization of barium titanate using in situ neutron powder diffraction.

The hydrothermal crystallization of barium titanate, BaTiO3, has been studied in situ by time-resolved powder neutron diffraction methods using the recently developed Oxford/ISIS hydrothermal cell. This technique has allowed the formation of the ferroelectric ceramic to be followed in a noninvasive manner in real time and under genuine reaction conditions. In a first set of experiments, Ba(OD)2-8D2O was reacted with two different titanium sources, either crystalline TiO2 (anatase) or amorphous TiO2-H2O in D2O, at 100-140 degrees C and the reaction studied using the POLARIS time-of-flight neutron powder diffractometer, at the ISIS Facility. In a second series of experiments, the reaction between barium chloride and crystalline TiO2 (anatase) in NaOD/D2O was studied at temperatures between 100 and 200 degrees C and at different deuterioxide concentrations using the constant-wavelength D20 neutron powder diffractometer at the Institut Laue Langevin. Quantitative growth and decay curves were determined from analysis of the integrated intensities of Bragg reflections of starting materials and product phases. In both sets of experiments the rapid dissolution of the barium source was observed, followed by dissolution of the titanium source before the onset of crystallization of barium titanate. Using a nucleation-growth model we are able to simulate the growth curve of barium titanate at three temperatures. Our results indicate the predominance of a homogeneous dissolution-precipitation mechanism for the hydrothermal formation of barium titanate, rather than other possible mechanisms that have been discussed in the literature. Analysis of the line widths of the Bragg reflections in the neutron diffraction data indicates that the particle size of the BaTiO3 product phase prepared from the amorphous TiO2-H2O is smaller than that prepared from crystalline TiO2 (anatase).     

Dispersion and Structure Studies of Molybdenum Oxide on Anatase TiO2

X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS) were used to characterize the structure of the mixture of molybdenum oxide and anatase calcined at 723 K. The resuits indicate that molybdenum oxide can disperse onto the surface of anatase (TiO2) and the dispersion threshold is 11.2 mg in per gram of MoO3 or 4.8 Mo atoms/nm^2 TiO2. When the coment of MoO3 is below the dispersion threshold, MoO3 species is in highly dispersed state interacting strongly with TiO2 support and in discrete tetrahedral coordination. [MoO4], on the surface of TiO2. When the MoO3 loading is above this value, MoO3 exists in both dispersed phase and crystalline phase. MoO3 in dispersed phase is still a discrete [MoO4] tetrahedron; MoO3 in crystal phase is in octahedral coordination.     

TiO2/Au纳米棒阵列的制备及其光催化性能

采用电沉积和旋转涂膜相结合的方法成功制备了高度有序的TiO2/Au纳米棒阵列催化剂.扫描电镜和透射电镜结果表明,TiO2薄膜均匀地包覆在Au纳米棒的表面,形成核壳型的一维阵列结构.X射线衍射分析表明所获得TiO2为(101)晶面优先生长的锐钛矿晶相.紫外-可见漫反射光谱显示,由于Au和TiO2间肖特基结的存在造成吸收红...     

1H NMR spectroscopic investigations on the micellization and gelation of PEO-PPO-PEO block copolymers in aqueous solutions

The effects of temperature, polymer composition, and concentration on the micellization and gelation properties of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) block copolymers in aqueous solutions were investigated by 1H NMR spectroscopy. It was found that the temperature-dependent behavior of PPO blocks, observed as changes in chemical shift, half-height width, and integral value, could be attributed as an intrinsic tool to characterize the transition states during unimer to micelle formation. The 1H NMR spectral analysis revealed that the hydrophobic part, PPO, of the Pluronic polymers plays a more significant role in the temperature-induced micellization, whereas the transitional behavior of Pluronic polymer, i.e., from micellization to liquid crystals formation, resulted in the drastic broadening of the spectral signals for the PEO, indicating that the PEO segments play a more significant role in the crystallization process. It was also observed that the temperature-dependent changes in the half-height width of the PEO -CH2- signal are sensitive to the liquid crystalline phase formation, which could be attributed to the close packing of spherical micelles at high polymer concentrations or temperatures.     

D-π-A dye system containing cyano-benzoic acid as anchoring group for dye-sensitized solar cells

A D-π-A dye (KM-1) incorporating cyano-benzoic acid as a new acceptor/anchoring group has been synthesized for dye-sensitized solar cells (DSCs) with a high molar extinction coefficient of 66,700 M(-1) cm(-1) at 437 nm. Theoretical calculations show that the hydrogen bond between -CN and surface hydroxyl leads to the most stable configuration on the surface of TiO(2). In addition, the adsorption of the dye on TiO(2) follows a Brunauer-Emmett-Teller (BET) isotherm. Multilayer adsorption of KM-1 on TiO(2) seems to take place particularly at higher dye concentrations. DSC device using KM-1 reached a maximum incident photon-to-current conversion efficiency (IPCE) of 84%, with a solar to electric power conversion efficiency (PCE) of 3.3% at AM1.5 G illumination (100 mW cm(-2)). This new type of anchoring group paves a way to design new dyes that combine good visible light harvesting with strong binding to the metal oxide surface.     

A calorimetry and light scattering study of the formation and shape transition of mixed micelles of EO20PO68EO20 triblock copolymer (P123) and nonionic surfactant (C12EO6)

The interaction between the nonionic surfactant C12EO6 and the poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymer EO20PO68EO20 (P123) has been investigated by means of isothermal titration and differential scanning calorimetry (DSC) as well as static and dynamic light scattering (SLS and DLS). P123 self-assembles in water into spherical micelles at ambient temperatures. At raised temperatures, the DSC data revealed a sphere-to-rod transition of the P123 micelles around 60 degrees C. C12EO6 interacts strongly with P123 micelles in aqueous solution to give mixed micelles with a critical micelle concentration (cmc) well below the cmc for pure C12EO6. The presence of C12EO6 also lowers the critical micelle temperature of P123 so aggregation starts at significantly lower temperatures. A new phenomenon was observed in the P123-C12EO6 system, namely, a well-defined sphere-to-rod transition of the mixed micelles. A visual phase study of mixtures containing 1.00 wt % P123 showed that in a narrow concentration range of C12EO6 both the sphere-to-rod transition and the liquid-liquid phase separation temperature are strongly depressed compared to the pure P123-water system. The hydrodynamic radius of spherical mixed micelles at a C12EO6/P123 molar ratio of 2.2 was estimated from DLS to be 9.1 nm, whereas it is 24.1 nm for the rodlike micelles. Furthermore, the hydrodynamic length of the rods at a molar ratio of 2.2 is in the range of 100 nm. The retarded kinetics of the shape transition was detected in titration calorimetric experiments at 40 degrees C and further studied by using time-resolved DLS and SLS. The rate of growth, which was slow (>2000 s), was found to increase with the total concentration.     

Microwave-induced synthesis of porous single-crystal-like TiO2 with excellent lithium storage properties

Porous anatase TiO(2) single crystal architectures with large specific surface area and remarkable crystalline phase-stability were fabricated via a green microwave-assisted process. Ionic liquid was chosen as both an essential structure-directing agent for the formation of the {001} facets exposed TiO(2) and an etching agent source for selective erosion of the exposed {001} facets, leading to robust porous framework with exposed {101} facets. These porous anatase single crystals were thermally stable up to 800 °C, indicating excellent structure stability. The product showed stable cyclability at high current rate, better reversibility, and high Coulumbic efficiency of 100% for lithium storage.     

Synthesis of aluminium borate-boron oxide and binary titanium-boron and zirconium-boron oxides from metal alkoxides and (MeO)3B3O3 in non-aqueous solvents

The reaction of metal alkoxides M(OR)4 (M = Ti, Zr; R = organyl) with (MeO)3B3O3 (1 : 0.67) in dry propan-2-one at room temperature led to gels which when dried and calcined in air for 24 h at 500-1000 degrees C afforded bi-phased mixed-oxide materials formulated as 4TiO2 x 3B2O3 and ZrO2 x B2O3 in high ceramic yields and purity; the B2O3 phases of these materials were amorphous. The materials remained amorphous upon calcination at lower temperatures. The TiO2 phase of the 4TiO2 x 3B2O3 was crystalline when calcined at higher temperatures with either anatase (600 degrees C) or rutile (>800 degrees C) being obtained. The ZrO2 phase of the ZrO2 x B2O3 was crystalline when calcined at higher temperatures and was obtained as a metastable tetragonal phase (<700 degrees C) or baddeleylite (>800 degrees C). In a similar reaction, Al(O(i)Pr)3 (2 : 1) gave a bi-phased aluminium borate-boron oxide (Al18B4O(33).7B2O3) after calcination at >700 degrees C. The dried gels and oxide materials were all characterized by elemental analysis, TGA-DSC, and powder XRD.     

Rectangular bunched rutile TiO2 nanorod arrays grown on carbon fiber for dye-sensitized solar cells

Because of their special application in photovoltaics, the growth of one-dimensional single-crystalline TiO(2) nanostructures on a flexible substrate is receiving intensive attention. Here we present a study of rectangular bunched TiO(2) nanorod (NR) arrays grown on carbon fibers (CFs) from titanium by a "dissolve and grow" method. After a corrosion process in a strong acid solution, every single nanorod is etched into a number of small nanowires. Tube-shaped dye-sensitized solar cells are fabricated by using etched TiO(2) NRs-coated CFs as the photoanode. An absolute energy conversion efficiency of 1.28% has been demonstrated under 100 mW cm(-2) AM 1.5 illumination. This work demonstrates an innovative method for growing bunched TiO(2) NRs on flexible substrates that can be applied in flexible devices for energy harvesting and storage.     

Relationship Between Photocatalytic Activity and Structure of TiO2 Thin Film

TiO2 thin films with different crystalline structures were prepared by the CVD method. The relationship between photocatalytic activity of a TiO2 thin film and its crystalline type was investigated. These films were characterized by XRD and AFM. Their photocatalytic properties were tested by the degradation of NO2-. The results showed that the crystalline structures of TiO2 thin films are primary anatase and/or rutile when the preparation temperatures were less than 573 K and higher than 773 K respectively. When the preparation temperature was around 623 K, the structures of TiO2 thin films were mixed crystalline structure, which showed the highest catalytic activity. When the ratio of rutile to anatase in TiO2 thin films fell between 0.5 and 0.7, the highest catalytic activity for the degradation of NO2- was found.     

Electrophoretic deposition of mesoporous TiO2 nanoparticles consisting of primary anatase nanocrystallites on a plastic substrate for flexible dye-sensitized solar cells

A film of mesoporous TiO(2) nanoparticles (MTNs) consisting of anatase nanocrystallites was electrophoretically deposited and compressed on a plastic substrate for the corresponding DSSC that gave an excellent conversion efficiency (η) of 5.25% under illumination of 100 mW cm(-2).