Determination of C4-C14 carboxylic acids by capillary zone electrophoresis. Application to the identification of diamide degradation products and partitioning studies.

Capillary zone electrophoresis (CZE) was investigated for the determination of linear saturated carboxylic acid homologues ranging from C₄ to C₁₄. Separation conditions were optimised to overcome the problems of decreasing solubility and decreasing selectivity between successive homologues with increasing chain length. Separations were performed at 20°C, using a 20 kV separation voltage and a pH 8 electrolyte containing 30% methanol. A suitable chromophore (4-aminobenzoate) was added to ensure indirect UV detection of the analytes. Calibration curves and repeatability were established. Minimum detectable concentrations of 3·10⁻⁶ mol l⁻¹ were achieved. Resolution between successive homologues was better than 2. The electrophoretic mobility of each homologue (n=7–14) was assessed and a quasi-linear relationship between the mobility value and 1/n was observed. The quantitative analysis of a diamide degradation solution was performed and compared to potentiometric results. The CZE method was also applied to the determination of C₇–C₁₄ partitioning between an organic medium containing tributylphosphate in n-dodecane and different basic solutions. Their behaviour was established according to the chain length and the pH of the aqueous phase. For C₁₀–C₁₄ compounds, results were validated by comparison with gas chromatographic analysis of the organic phases.     

An electron transfer mechanism of O4 formation

A resonating valence bond electron transfer mechanism of combining two O₂ molecules to form an O₄ molecule is presented. The predicted molecular states of the reaction path D_∞h→C_2v→D_2h are supported by the present ab initio molecular orbital calculations. The CASPT2 BSSE calculations yield a stable diamagnetic D_2h O₄ molecule with a very weak chemical bond between the monomers, in good agreement with experiments. A low activation barrier energy of 26 cal/mol for the O₄ formation is found.     

Synthesis of methyltrioxorhenium(VII) arylamine complexes and mono- and bis(ortho)-chelated arylaminorhenium(VII) trioxides

From the reaction of MeReO₃ with the neutral arylamine C₆H₅CH₂NMe₂ and the aryldiamine C₆H₄(CH₂NMe₂)₂−1,3, have been isolated in good yields the 1/1 adduct complex [MeReO₃ · C₆H₅CH₂NMe₂], 1, and the 2/1 adduct complex [(MeReO₃)₂ · C₆H₄(CH₂NMe₂)₂− 1,3], 2, respectively. The X-ray molecular structure of 2 shows that both rhenium centres have a trigonal bipyramidal geometry and in the axial positions of each rhenium centre are one of the NMe₂ units of the aryldiamine ligand and a methyl group. The mono(ortho)-chelated arylaminorhenium trioxide complex [ReO₃(C₆H₄CH₂NMe₂−2], 3, can be synthesized by a transmetallation reaction of ClReO₃ with [ZnC₆H₄CH₂NMe₂−2₂] in a 2:1 molar ratio. In a similar way the bis(ortho)-chelated arylaminorhenium trioxide complex [ReO₃C₆H₃(CH₂NMe₂)₂−2,6], 4, can be synthesized by addition of a mixture of [Li₂C₆H₃(CH₂NMe₂)₂−2,6₂] and ZnCl₂ to ClReO₃. Complexes 3 and 4 have been isolated as white solids in 66% and 81% yields respectively. The rhenium centre in complex 4 has a bicapped tetrahedral geometry in which the monoanionic C₆H₃(CH₂NMe₂)₂−2,6⁻ ligand is pseudo-facially bonded with a characteristic N1-Re-N2 angle of 107.7(3)°, a Re-C_ipso bond length of 2.112(11) Å and Re-N1 and Re-N2 bond lengths of 2.518(9) Å and 2.480(8) Å respectively.     

Mesogenic Unsymmetric dimers containing cholesteryl ester and tolane moieties

Among unsymmetric oligomesogens, chiral dimers formed by connecting a cholesteryl ester fragment with various aromatic mesogenic cores through a polymethylene spacer have been attracting much attention due to their remarkable thermal behaviour. In particular, dimers containing a diphenylacetylene segment having an alkoxy chain have shown interesting mesomorphic behaviour. In view of this a new series of unsymmetric dimers consisting of a diphenylacetylene moiety having an alkyl chain and a cholesteryl ester unit joined through a paraffinic spacer have been synthesized and their liquid crystalline properties characterized. The lengths of the central methylene spacer (C₃, C₄, C₅ and C₇) as well as that of the alkyl chain (n-butyl, n-pentyl, n-hexyl and n-heptyl) have been varied to establish structure-property relationships. These investigations have revealed that all the dimers exhibit smectic A, twist grain boundary and chiral neamtic (N*) phases with the exception of one of the dimers for which only the N* phase was observed. Some differences in the mesomorphic properties of the unsymmetric dimers containing odd or even parity methylene spacers have been observed. The majority of dimers having an even (C₄) parity paraffinic spacer show a blue phase while the dimers with odd (C₃, C₅ and C₇) parity spacers exhibit the chiral smectic (SmC*) phase. In some cases, the SmC* phase exists well below (-60°C) and above room temperature.     

The electrolyte NRTL model and speciation approach as applied to multicomponent aqueous solutions of H2SO4, Fe2(SO4)3, MgSO4 and Al2(SO4)3 at 230–270 °C

This work presents chemical modeling of solubilities of metal sulfates in aqueous solutions of sulfuric acid at high temperatures. Calculations were compared with experimental solubility measurements of hematite (Fe₂O₃) in aqueous ternary and quaternary systems of H₂SO₄, MgSO₄ and Al₂(SO₄)₃ at high temperatures. A hybrid model of ion-association and electrolyte non-random two liquid (ENRTL) theory was employed to fit solubility data in three ternary systems H₂SO₄–MgSO₄–H₂O, H₂SO₄–Al₂(SO₄)₃–H₂O at 235–270 °C and H₂SO₄–Fe₂(SO₄)₃–H₂O at 150–270 °C. Employing the Aspen Plus™ property program, the electrolyte NRTL local composition model was used for calculating activity coefficients of the ions Al³⁺, Mg²⁺ Fe³⁺ and SO₄²⁻, HSO₄⁻, OH⁻, H₃O⁺, respectively, as well as molecular species. The solid phases were hydronium alunite (H₃O)Al₃(SO₄)₂(OH)₆, hematite Fe₂O₃ and magnesium sulfate monohydrate (MgSO₄)·H₂O which were employed as constraint precipitation solids in calculating the metal sulfate solubilities. A correlation for the equilibrium constants of the association reactions of complex species versus temperature was implemented. Based on the maximum-likelihood principle, the binary interaction energy parameters for the ionic species as well as the coefficients for equilibrium constants of the reactions were obtained simultaneously using the solubility data of the ternary systems. Following that, the solubilities of metal sulfates in the quaternary systems H₂SO₄–Fe₂(SO₄)₃–MgSO₄–H₂O, H₂SO₄–Fe₂(SO₄)₃–Al₂(SO₄)₃–H₂O at 250 °C and H₂SO₄–Al₂(SO₄)₃–MgSO₄–H₂O at 230–270 °C were predicted. The calculated results were in excellent agreement with the experimental data.     

Characterization and decomposition mechanism of an unusual nickel, thiocyanate and 4-methylpyridine polymeric complex

The synthesis, characterization, and thermal decomposition of the [Ni(SCN)₂(H⁺SCN)₂(4-mepy)₂] compound with an octahedral structure in polymeric chain were reported, in which SCN groups form bridges among Ni(II) ions. The compound decomposes in water resulting in a pH<4 solution. The FT-IR spectrum presented doublet bands at 2117; 2128 cm⁻¹, 788; 773 cm⁻¹ assigned to ν(C---N) and ν(C---S) stretching modes, respectively, and δ(SCN) deformation modes at 468; 476 cm⁻¹. The Raman spectrum of the compound presented the ν(C---N) stretching as a strong doublet at 2122; 2128 cm⁻¹, ν(C---S) at 783; 770 cm⁻¹, and δ(SCN) at 468; 477 cm⁻¹. No significant changes were observed in the 4-mepy ligand bands compared with the vibrational frequencies of the pure compound or the compound in aqueous solution 0.2 mol l⁻¹. The crystal UV–vis reflectance spectrum presented two bands centered in 626 and 424 nm tentatively assigned to the d→d type transitions, ³A_2g→³T_1g and ³A_2g→³T_1g, for a symmetry close to O_h. The TG curve showed a mass loss between 120 and 200 °C assigned to the loss of the two 4-mepy molecules; from 200 to 265 °C, the loss of the two H⁺SCN groups; and from 265 to 450 °C, the loss of the two SCN groups that formed the bridges among the nickel atoms. Based on these mass loss data, a mechanism of thermal decomposition for the compound was proposed.     

The system CePO4–K3PO4

The phase diagram of the system CePO₄–K₃PO₄ has been determined based on investigations by differential thermal analysis, X-ray powder diffraction, IR spectroscopy and optical microscopy. The system contains only one intermediate compound K₃Ce(PO₄)₂, which melts incongruently at (1500±20)°C. This compound is stable down to room temperature and exhibits a polymorphic transition at 1180°C. It was confirmed that the low-temperature form β-K₃Ce(PO₄)₂ crystallizes in a monoclinic system, space group P2₁/m with unit cell parameters a=9.579 (5), b=5.634 (6), c=7.468 (5) Å; =γ=90°, β=90.81 (3)°; V=403.083 Å³.     

Crystal structure of 4-methoxybenzylidene-4'-n-butylaniline (MBBA) The C4 and C3 phases

Precise knowledge of thermal history (quenching and annealing) of the phases of the quenched liquid crystal MBBA has permitted us, from powder X-ray data, to attribute unequivocally a previously published structure to the C₄ metastable phase. Lattice parameters of the C₃ phase are also proposed.     

Spectres de rotation de la molécule de chlorobenzène : II. Variétés isotopiques multisubstituées et structure géométrique précise

In order to complete the r_s structure of chlorobenzene given in a preceding paper, a variety of isotopic species of this molecule were synthesized and their microwave spectra studied. This made twenty isotopic species available, enabling the determination of the geometrical parameters by a least squares method. Fitting only differences of moments of inertia either for monosubstituted species or to multiply substituted species gave the same result. They hardly differ from the r_o values and agree with the r_s values obtained by the Kraitchman equations. The resulting error limits were reduced, however.

The following structural parameters were obtained, C₁C₂ = 1.399 Å, C₂C₃ = 1.386 Å, C₃C₄ = 1.3976 Å, C₁Cl = 1.7248 Å, C₂H₂ = 1.080 Å, C₃H₃ = 1.081 Å, C₄H₄ = 1.081 Å, C₆C₁C₂ = 120° 16, C₁C₂C₃ = 119°78, C₂C₃C₄ = 120°24, C₃C₄C₅ = 119°80, C₁C₂H₂ = 119°45, C₂C₃H₃ = 119°76.

The structure of the ring differs significantly from C₆ symmetry. The deformation can be regarded as a compression of the position C₁ while the angle of C₂H₂ bond is also changed.     

Three-phase extraction study of cyanex 923-n-heptane/H(2)SO(4) system

Phase behavior of the extraction system, Cyanex 923–heptane/H₂SO₄–H₂O has been studied. The third phase appeared at different aqueous H₂SO₄ concentration with varying initial Cyanex 923 concentration and temperature affects its appearance. Almost all of H₂SO₄ and H₂O are extracted into the middle phase. The H₂SO₄ concentration in the third phase increases with the increasing aqueous acid concentration (C_H2SO4,b) while the water content first increases and then reaches a constant value at C_H2SO4,b=11.3 mol l⁻¹. In the region of C_H2SO4,b higher than 5.2 mol l⁻¹, the composition of the middle phase is only related to the equilibrium concentration of H₂SO₄ in the bottom phase. H₂SO₄ and H₂O are transferred into the middle phase mainly by their coordination with Cyanex 923 when C_H2SO4,b is less than 11.3 mol l⁻¹. When C_H2SO4,b is higher than 11.3 mol l⁻¹, excess H₂SO₄ is solubilized into the polar layer of the aggregates. In the region considered, the extracted complex changes from C923 · H₂SO₄ to C923 · H₂SO₄ · H₂O and then to C923 · (H₂SO₄)₂ · H₂O.     

Lifetime measurements of electronically excited C3(Πu) radicals in different vibrational states

The radiative lifetimes of nine vibrational levels of the C₃(¹Π_u) radical were obtained from decay time studies of the C₃(¹Π_u → ¹Σ⁺_g) fluorescence induced by a tunable dye laser. The lifetimes of the different vibronic levels were found to be constant within the experimental error limits, namely, τ_o = (200 ± 10) ns. The collisional deactivation of the C₃(¹Π_u) states by helium gives rate constants between 2.5 and 4 in 10⁻¹¹ cm³ molecule⁻¹ s⁻¹ units.     

Alkyl-substituted cyclopentadienyl- and phospholyl-zirconium/MAO catalysts for propene and 1-hexene oligomerization

The directed oligomerization of propene and 1-hexene was carried out with a series of Cp′(C₅H₅)ZrCl₂ and Cp₂′ZrCl₂ pre-catalysts (Cp′=C₅HMe₄, C₄Me₄P, C₅Me₅, C₅H₄^tBu, C₅H₃-1,3-^tBu₂, C₅H₂-1,2,4-^tBu₃) together with (C₅H₅)₂ZrCl₂. Oligomers in the molar mass range 300–1500 g/mol for propene and 200–3000 g/mol for 1-hexene were synthesized at 50 °C. The majority of oligomer molecules contain a double-bond end group. Oligomer characterization was carried out by gel permeation chromatography (GPC), ¹H and ¹³C NMR. Vinylidene double bonds (from β-hydrogen elimination) are solely found for the tert-butyl-substituted zirconocenes and for most of the unsymmetrical methyl-substituted Cp′(C₅H₅)ZrCl₂ systems (except Cp′=phospholyl). With (C₄Me₄P)(C₅H₅)ZrCl₂ and with the symmetrical methyl-containing Cp₂′ZrCl₂ pre-catalysts, also vinyl end groups (from β-methyl elimination) are observed in the case of oligopropenes. The vinylidene/vinyl ratio depends on the ligand and the vinyl content increases from C₅HMe₄ (65/35) over C₄Me₄P (61/39) to C₅Me₅ (9/91). The phospholyl zirconocenes and (C₅HMe₄)₂ZrCl₂ also exhibit chain-transfer to aluminum thereby giving saturated oligomers.     

In situ observation of the pressure-induced mesophase for 4'-n-hexadecyloxy-3'-nitrobiphenyl-4-carboxylic acid

In situ observation of the optical texture, and X-ray patterns of the pressure-induced mesophase seen for 4'-n-hexadecyloxy-3'-nitrobiphenyl-4-carboxylic acid (ANBC-16) was performed under hydrostatic pressures up to 100MPa using a polarizing optical microscope equipped with a high pressure hot stage and a wide angle X-ray diffractometer equipped with a high pressure vessel respectively. It was found that the pressure-induced mesophase (hereafter refered to as 'X') appeared at pressures above 60 MPa, and exhibits a birefringent broken-fan or a sand-like texture that remain unaltered in the SmC phase. The POM-transmitted light intensity curve measured on heating clearly showed the Cr₄ →Cr₁ →SmC →'X' →SmA →I transition sequence at 80 MPa. The optical texture and the POM-transmitted light intensity measured during a pressure cycle at 185°C showed a reversible change between the cubic and 'X' phases. The WAXD pattern of the 'X' phase showed a spot-like pattern, suggesting no layered structure for this phase, and also revealed a substantial decrease in the d-spacing of the low angle reflection at 80 and 100 MPa, compared with the d-spacings of the (0 0 1) reflection of the SmC phase and also the (2 1 1) reflection of the cubic phase. It is concluded from these data that the 'X' phase is a birefringent hexagonal columnar phase.     

Protonated ethanol and its neutral counterparts

Collisionally activated dissociation and neutralization-reionization experiments reveal that protonation of ethanol leads to two distinct isomers, the classical ion CH₃CH₂OH⁺₂ and the proton-bound complex C₂H₄…H⁺…OH₂. The neutral counterpart of the latter is unstable, whereas that of the former can be produced in a bound state if the CH₃CH₂OH⁺₂ precursor ion is formed under low ion source pressure conditions and, thus, with higher internal energies. This suggests that there are substantial differences in the geometries of CH₃CH₂OH⁺₂ and the hypervalent CH₃CH₂OH₂ ·. This provides only a partial explanation for unusual isotope effects; C₂H₅OD₂ ·, CH₃CD₂OD₂ ·, and CD₃CH₂OD₂ · are substantially more stable than C₂D₅OD₂ · and C₂H₅OH₂ ·.     

Synthesis and mesomorphic properties of 4-alkylamino-4'-substituted diphenyldiacetylenes

Various substituted aminodiphenyldiacetylenes of the type with X = C₃H₇, C₅H₁₁, F or NO₂ and R, R' = H, CH₃-C₆H₁₃ were synthesized and their mesomorphic properties determined. Semi-empirical and ab initio quantum chemical calculations using AM1, 421G and 631G* suggested that the amino group would increase the dielectric anisotropy and optical birefringence as compared to the alkyl chain. Mesomorphic properties were found to be poor with the maximum nematic phase range being 44.8°C and many of the compounds having no nematic phase. Both melting temperatures and enthalpies for those having nematic phases were too high to form good eutectic mixtures.     

Photon energy upconversion in porphyrins: one-photon hot-band absorption versus two-photon absorption

We study the porphyrin S₁→S₀ fluorescence and the photosensitized singlet oxygen ¹Δ_g→³Σ_g phosphorescence, both originating from absorption of photons with energy less than the porphyrin S₀→S₁ transition energy. By measuring the excitation intensity dependence of fluorescence at lowered sample temperatures, we are able to discriminate between two parallel processes of one-photon hot-band absorption (HBA) and simultaneous two-photon absorption (TPA). When the HBA and TPA contributions are comparable in magnitude, we use this new method to determine absolute TPA cross-section. We also demonstrate for the first time a singlet oxygen photosensitization via HBA in porphyrin.     

Geometry and nature of the binding of the pre-reactive complex C2H4…ClF from its rotational spectrum

The encounter complex C₂H₄…ClF was isolated by using a fast-mixing nozzle before chemical reaction could occur between the components and was characterised by Fourier-transform microwave spectroscopy. Rotational constants, centrifugal distortion constants, Cl nuclear quadrupole constants and Cl spin-rotation constants were determined for the isotopomers C₂H₄…³⁵ClF and C₂H₄…³⁷ClF. The complex has C_2v symmetry with the ClF subunit perpendicular to the plane of C₂H₄ and oriented so that Cl is closer to C₂H₄. Both the centrifugal distortion constant Δ_J and the Cl nuclear quadrupole coupling constants indicate that the complex is relatively weakly bound and it is concluded that the interaction between the subunits is largely electrostatic in origin.     

Synthesis and thermal behaviour of salicylaldimine-based liquid crystalline symmetrical dimers

A series of symmetrical dimers consisting of salicylaldimine moieties connected by flexible alkylene central spacer via ether linkages has been synthesized. In order to validate the empirical rule suggested by Date et al. to account for the smectic behaviour of such dimers, the chain length of the terminal alkoxy chain has been kept constant (C₈) while the number of methylene units in the central spacer was varied from C₃ to C₁₁. Another aim of the present investigation was to understand structure-property relationship in these dimers in which the salicylaldimine mesogenic segment has been used for the first time in dimers. The mesomorphic behaviour of these dimers was evaluated using optical microscopy and differential scanning calorimetry and the structure of some of the mesophases has been further investigated with the help of X-ray diffraction. Our studies reveal that the dimers consisting of 3 to 8 methylene units in the flexible spacer show only smectic (smectic C and smectic A) phases. For the dimers containing 4, 6 and 8 methylene units in the central spacer, a unique filament growth pattern has been observed in the smectic A phase while cooling from the isotropic phase. The dimers containing of C₉ to C₁₁ methylene groups exhibit the nematic phase in addition to smectic modifications. This observation indicates that when the terminal chains are shorter than the spacer, the tendency to form smectic phases is not fully extinguished but is perhaps reduced.     

Thermal stability of osmium mixed oxides I. CaOsO3 decomposition products: A new orthorhombic phase Ca2Os2O7

The thermal decomposition of CaOsO₃ by differential thermal analyses, thermogravimetry and X-ray powder diffraction has been studied. In nitrogen CaOsO₃ decomposes at 880 ± 10°C into CaO, osmium metal and oxygen due to the reaction CaOsO₃ → CaO + Os + O₂. In static air the decomposition occurs in three stages: 2CaOsO₃ + 1/2O₂ → Ca₂Os₂O₇ (in region 775–808°C), Ca₂Os₂O₇ → Ca₂Os₂O_6,5 + 1/4O₂ (at a temperature interval of 850–1000°C) and in the third stage Ca₂Os₂O_6,5 → 2CaO + OsO₄ ÷ 1/4 O₂ (at 1005 ± 5°C). The first intermediate Ca₂Os₂O₇ is isostructural with orthorhombic Ca₂Nb₂O₇ and its cell parameters are: a₀ = 3.745 Å, b₀ = 25.1 Å, c₀ = 5.492 Å, Z = 4, space group Cmcm or Cmc2. Ca₂Os₂O₇ exhibits metallic conductivity and its electrical resistivity is 4.6 × 10⁻² ohm-cm at 296K.     

The synthesis and liquid crystal transition temperatures of some weakly polar nematic methyl (E)-[trans-4-substituted-cyclohexyl]-allyl ethers

We have introduced an oxygen atom and a carbon-carbon double bond with a trans-configuration (E) into the terminal alkyl chain of a wide variety of liquid crystalline cyclohexane derivatives to produce a variety of new methyl (E)-allyl ethers. The melting points and tendency to form smectic mesophases are often low, while nearly all of the compounds prepared exhibit a nematic phase. Thus, even two-ring derivatives can exhibit nematic phases over a wide temperature range (≤80°C), sometimes starting below room temperature (T_m≈10°C). Comparisons with the corresponding derivatives incorporating either just an oxygen atom or just a carbon-carbon double bond in the same position indicate that synergetic effects lead to broader nematic phases than would otherwise have been expected. Thus many of the new methyl (E)-allyl ethers exhibit nematic phases over a wider temperature range than the corresponding materials with an unsubstituted alkyl chain attached to the cyclohexyl ring. The new compounds are easily prepared from known starting materials. Many intermediates are themselves liquid crystalline. This allows investigation of the relationship between liquid crystal transition temperatures and the nature of the terminally substituted alkyl chain (for example, incorporating C=C, OH, CO₂C₂H₅ and OCH₃ groups).