Simultaneous voltammetric determination of ascorbic acid and uric acid using a Nafion/multi-wall carbon nanotubes composite film-modified electrode

A Nafion/multi-wall carbon nanotubes (MWNT) composite film-modified electrode was fabricated. The modified electrode showed excellent electrocatalytic activity toward ascorbic acid (AA) and uric acid (UA) in 0.1-mol L⁻¹ NaCl medium (pH 6.5). Compared to the bare electrode that only displayed a broad and overlapped oxidation peak, the Nafion/MWNT film-modified electrode not only remarkably enhanced the anodic peak currents of AA and UA but also avoided the overlapping of the anodic peaks of AA and UA with a 320-mV separation of both peaks. Under the optimized conditions, the peak currents of AA and UA were proportional to their concentration at the ranges of 8.0 × 10⁻⁵ to 6.0 × 10⁻³ mol L⁻¹ and 6.0 × 10⁻⁷ to 8.0 × 10⁻⁵ mol L⁻¹, respectively. The proposed method was used for the detection of AA and UA in real samples with satisfactory results.     

Electrocatalytic oxidation of quinine sulfate at a multiwall carbon nanotubes-ionic liquid modified glassy carbon electrode and its electrochemical determination

The electrocatalytic oxidation of quinine sulfate (QS) was investigated at a glassy carbon electrode, modified by a gel containing multiwall carbon nanotubes (MWCNTs) and room-temperature ionic liquid of 1-Butyl-3-methylimidazolium hexafluorophate (BMIMPF₆) in 0.10 M of phosphate buffer solution (PBS, pH 6.8). It was found that an irreversible anodic oxidation peak of QS with E _pa as 0.99 V appeared at MWCNTs-RTIL/glassy carbon electrode (GCE). The electrode reaction process was a diffusion-controlled one and the electrochemical oxidation involved two electrons transferring and two protons participation. Furthermore, the charge-transfer coefficient (α), diffusion coefficient (D), and electrode reaction rate constant (k _f) of QS were found to be 0.87, 7.89 × 10⁻³ cm²⋅s⁻¹ and 3.43 × 10⁻² s⁻¹, respectively. Under optimized conditions, linear calibration curves were obtained over the QS concentration range 3.0 × 10⁻⁶ to 1.0 × 10⁻⁴ M by square wave voltammetry, and the detection limit was found to be 0.44 μM based on the signal-to-noise ratio of 3. In addition, the novel MWCNTs-RTIL/GCE was characterized by the electrochemical impedance spectroscopy and the proposed method has been successfully applied in the electrochemical quantitative determination of quinine content in commercial injection samples and the determination results could meet the requirement.     

Electrochemical behavior and determination of epinephrine at a mercaptoacetic acid self-assembled gold electrode

The electrochemical behavior of epinephrine (EP) at a mercaptoacetic acid (MAA) self-assembled monolayer modified gold electrode was studied. The MAA/Au electrode is demonstrated to promote the electrochemical response of epinephrine by cyclic voltammetry. The possible reaction mechanism is also discussed. The diffusion coefficient D of EP is 6.85 × 10⁻⁶ cm² s⁻¹. In 0.1 mol L⁻¹ phosphate buffer (pH 7.20), a sensitive oxidation peak was observed at 0.177 V, and the peak current is proportional to the concentration of EP in the range of 1.0 × 10⁻⁵–2.0 × 10⁻⁴ mol L⁻¹ and 1.0 × 10⁻⁷–1.0 × 10⁻⁶ mol L⁻¹. The detection limit is 5 × 10⁻⁸ mol L⁻¹. The modified electrode is highly stable and can be applied to the determination of EP in practical injection samples. The method is simple, quick, sensitive and accurate.     

Voltammetric Analysis of the Novel Atypical Antipsychotic Drug Quetiapine in Human Serum and Urine

The electrooxidative behaviour and determination of quetiapine (QTP), a dibenzothiazepine derivative and antipsychotic agent, on a glassy carbon disc electrode was investigated using cyclic (CV), linear sweep (LSV), differential pulse (DPV) and Osteryoung square wave voltammetry (OSWV). Fully validated DP and SW voltammetric procedures are described for the determination of QTP. QTP in pH 3.5 acetate buffer solution presents a well-defined anodic response, studied by the proposed methods. This main response was due to the irreversible, diffusion-controlled, one-electron and one-proton oxidation of the aliphatic nitrogen of the piperazine ring. Under optimal conditions, a detection limit of 4.0 × 10⁻⁸ mol L⁻¹ for DPV and 1.33 × 10⁻⁷ mol L⁻¹ for OSWV, and a linear calibration graph in the range from 4.0 × 10⁻⁶ to 2.0 × 10⁻⁴ mol L⁻¹ were obtained for both methods. The procedure was successfully applied to the determination of the drug in tablets, human serum and human urine with good recoveries. The detection limits were 6.20 × 10⁻⁷ mol L⁻¹ and 5.92 × 10⁻⁷ mol L⁻¹ in human serum and 1.44 × 10⁻⁷ mol L⁻¹ and 1.31 × 10⁻⁶ mol L⁻¹ in human urine, for the DPV and OSWV method, respectively.     

A hydrogen peroxide biosensor based on direct electrochemistry of hemoglobin in palladium nanoparticles/graphene-chitosan nanocomposite film

Thermally two-dimensional lattice graphene (GR) and biocompatibility chitosan (CS) act as a suitable support for the deposition of palladium nanoparticles (PdNPs). A novel hydrogen peroxide (H₂O₂) biosensor based on immobilization of hemoglobin (Hb) in thin film of CS containing GR and PdNPs was developed. The surface morphologies of a set of representative membranes were characterized by means of scanning electron microscopy and showed that the PdNPs are of a sphere shape and an average diameter of 50 nm. Under the optimal conditions, the immobilized Hb showed fast and excellent electrocatalytic activity to H₂O₂ with a small Michaelis–Menten constant of 16 μmol L⁻¹, a linear range from 2.0 × 10⁻⁶ to 1.1 × 10⁻³ mol L⁻¹, and a detection limit of 6.6 × 10⁻⁷ mol L⁻¹. The biosensor also exhibited other advantages, good reproducibility, and long-term stability, and PdNPs/GR–CS nanocomposites film would be a promising material in the preparation of third generation biosensor.     

Electrochemical behaviors of metol on ionic-liquid-modified carbon paste electrode and its analytical application

The electrochemical behaviors of metol on an ionic liquid N-butylpyridinium hexafluorophosphate modified carbon paste electrode (IL-CPE) were studied in this paper. The results indicated that a pair of well-defined quasi-reversible redox peaks of metol appeared with the decrease of overpotential and the increase of redox peak current, which was the characteristics of electrocatalytic oxidation. The electrocatalytic mechanism was discussed and the electrochemical parameters were calculated with results of the charge-transfer coefficient (α) as 0.45, the electrode reaction rate constant (k _s) as 4.02 × 10⁻³ s⁻¹, and the diffusion coefficient (D) as 6.35 × 10⁻⁵ cm²/s. Under the optimal conditions, the anodic peak current was linear with the metol concentration in the range of 5.0 × 10⁻⁶ ∼ 1.0 × 10⁻³ mol/L (n = 11, γ = 0.994) and the detection limit was estimated as 2.33 × 10⁻⁶ mol/L (3σ). The proposed method was successfully applied to determination of metol content in synthetic samples and photographic solutions.     

Direct electrochemistry and electrocatalysis of nitrite based on nano-alumina-modified electrode

Simple and sensitive electrochemical method for the determination of nitrite, based on a nano-alumina-modified glassy carbon electrode (GCE), is described. Nitrite yields a well-defined oxidation peak whose potential is 0.74 V at the nano-alumina-coated GCE in 0.1 mol L⁻¹ phosphate buffer (pH 5.0). Compared with bare GCE, the nano-alumina-modified GCE has evident catalytic effect towards the oxidation of nitrite, and its peak current can be significantly enhanced. Some of the experimental parameters were optimized for the determination of nitrite. The oxidation peak current was proportional to nitrite concentration in the range of 5.0 × 10⁻⁸–1.1 × 10⁻³ mol L⁻¹, and a detection limit of 1.0 × 10⁻⁸ mol L⁻¹ was obtained. This method has been successfully used to the determination of nitrite in sausage sample. Furthermore, results obtained by the method have been compared with spectrophotometric method.     

Simple sensor for simultaneous determination of dihydroxybenzene isomers

A simple sensor based on bare carbon ionic liquid electrode was fabricated for simultaneous determination of dihydroxybenzene isomers in 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0). The oxidation peak potential of hydroquinone was about 0.136 V, catechol was about 0.240 V, and resorcinol 0.632 V by differential pulse voltammetric measurements, which indicated that the dihydroxybenzene isomers could be separated absolutely. The sensor showed wide linear behaviors in the range of 5.0 × 10⁻⁷–2.0 × 10⁻⁴ mol L⁻¹ for hydroquinone and catechol, 3.5 × 10⁻⁶–1.535 × 10⁻⁴ mol L⁻¹ for resorcinol, respectively. And the detection limits of the three dihydroxybenzene isomers were 5.0 × 10⁻⁸, 2.0 × 10⁻⁷, 5.0 × 10⁻⁷ mol L⁻¹, respectively (S/N = 3). The proposed method could be applied to the determination of dihydroxybenzene isomers in artificial wastewater and the recovery was from 93.9% to 104.6%.     

Selective and sensitive molecularly imprinted sol–gel film-based electrochemical sensor combining mercaptoacetic acid-modified PbS nanoparticles with Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@Au–multi-walled carbon nanotubes–chitosan

A sensitive molecularly imprinted electrochemical sensor was developed for selective detection of streptomycin by combination of mercaptoacetic acid-modified PbS nanoparticles with Au-coated Fe₃O₄ magnetic nanoparticles dispersed multi-walled carbon nanotubes doped chitosan film. The imprinted sensor was fabricated onto the Au electrode via stepwise modification of nanocomposites and an electrodeposited thin film of molecularly imprinted polymers via sol–gel technology. The morphologies and electrochemical behaviors of the imprinted sensor were characterized by scanning electron microscope, cyclic voltammetry, and differential pulse voltammetry, respectively. The prepared sensor showed very high recognition ability and selectivity for streptomycin. Under optimal conditions, the imprinted sensor displayed good electrocatalytic activity to the redox of streptomycin. And the differential voltammetric anodic peak current was linear to the logarithm of streptomycin concentration in the range from 1.0 × 10⁻⁶ to 1.0 × 10⁻³ mol L⁻¹, and the detection limit obtained was 1.5 × 10⁻⁹ mol L⁻¹. This proposed imprinted sensor was used successfully for streptomycin determination in different injection solution samples.     

Sensitive voltammetric sensor of dihydromyricetin based on Nafion/SWNT-modified glassy carbon electrode

A novel voltammetric sensor, based on single-walled carbon nanotubes (SWNT) dispersed in Nafion and modified glassy carbon electrode (GCE), was fabricated and used to determine the trace amounts of dihydromyricetin (DMY). The electrochemical behavior of DMY at this sensor was investigated in 0.1 mol L⁻¹ sulfuric acid solutions + 0.1 mol L⁻¹ NaCl by cyclic voltammetry and squarewave voltammetry. Compared with bare GCE, the electrode presented an excellent response of DMY through an adsorption-controlled quasi-reversible process. Under the optimum conditions, the response peak currents were linear relationship with the DMY concentrations in the range of 1.0 × 10⁻⁷–1.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 9 × 10⁻⁸ mol L⁻¹. Based on this voltammetric sensor, a simple and sensitive electroanalytical method for DMY was proposed and applied to quantitative determination of DMY in Ampelopsis grossedentata samples. In addition, the oxidation mechanism was proposed and discussed, which could be a reference for the pharmacological action of DMY in clinical study.     

Electrochemical characterization of 2, 2′-[1, 2-ethanediylbis (nitriloethylidyne)]-bis-hydroquinone-carbon nanotube paste electrode and its application to simultaneous voltammetric determination of ascorbic acid and uric acid

The preparation and electrochemical characterization of a carbon nanotube paste electrode modified with 2,2′-[1,2-ethanediylbis (nitriloethylidyne)]-bis-hydroquinone, referred to as EBNBH, was investigated. The EBNBH carbon nanotube paste electrode (EBNBHCNPE) displayed one pair of reversible peaks at E _pa = 0.18 V and E _pc = 0.115 V vs Ag/AgCl. Half wave potential (E _1/2) and ΔE _p were 0.148 and 0.065 V vs Ag/AgCl, respectively. The electrocatalytic oxidation of ascorbic acid (AA) has been studied on EBNBHCNPE, using cyclic voltammetry, differential pulse voltammetry and chronoamperometry techniques. It has been shown that the oxidation of AA occurs at a potential where oxidation is not observed at the unmodified carbon paste electrode. The heterogeneous rate constant for oxidation of AA at the EBNBHCNPE was also determined and found to be about 1.07 × 10⁻³ cm s⁻¹. The diffusion coefficient of AA was also estimated as 5.66 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometry. Also, this modified electrode presented the property of electrocatalysing the oxidation of AA and uric acid (UA) at 0.18 and 0.35 V vs Ag/AgCl, respectively. The separations of anodic peak potentials of AA and UA reached 0.17 V. Using differential pulse voltammetry, the calibration curves for AA and UA were obtained over the range of 0.1–800 μM and 20–700 μM, respectively. With good selectivity and sensitivity, the present method provides a simple method for selective detection of AA and UA in biological samples.     

Electrocatalytic oxidation of nitrite at a terpyridine manganese(II) complex modified carbon past electrode

A carbon past electrode modified with [Mn(H₂O)(N₃)(NO₃)(pyterpy)], ( \textpyterpy = 4￠- ( 4 - \textpyridyl ) - 2,2￠:\text6￠,\text2￠￠- \textterpyridine ) \left( {{\text{pyterpy}} = 4\prime - \left( {4 - {\text{pyridyl}}} \right) - 2,2\prime:{\text{6}}\prime,{\text{2}}\prime\prime - {\text{terpyridine}}} \right) complex have been applied to the electrocatalytic oxidation of nitrite which reduced the overpotential by about 120 mV with obviously increasing the current response. Relative standard deviations for nitrite determination was less than 2.0%, and nitrite can be determined in the ranges of 5.00 × 10⁻⁶ to 1.55 × 10⁻² mol L⁻¹, with a detection limit of 8 × 10⁻⁷ mol L⁻¹. The treatment of the voltammetric data showed that it is a pure diffusion-controlled reaction, which involves one electron in the rate-determining step. The rate constant k′, transfer coefficient α for the catalytic reaction, and diffusion coefficient of nitrite in the solution, D, were found to be 1.4 × 10⁻², 0.56× 10⁻⁶, and 7.99 × 10⁻⁶ cm² s⁻¹, respectively. The mechanism for the interaction of nitrite with the Mn(II) complex modified carbon past electrode is proposed. This work provides a simple and easy approach to detection of nitrite ion. The modified electrode indicated reproducible behavior, anti-fouling properties, and stability during electrochemical experiments, making it particularly suitable for the analytical purposes.     

Electrocatalytic oxidation of aspirin and acetaminophen on a cobalt hydroxide nanoparticles modified glassy carbon electrode

The electrocatalytic oxidation of aspirin and acetaminophen on nanoparticles of cobalt hydroxide electrodeposited on the surface of a glassy carbon electrode in alkaline solution was investigated. The process of oxidation and the kinetics have been investigated using cyclic voltammetry, chronoamperometry, and steady-state polarization measurements. Voltammetric studies have indicated that in the presence of drugs, the anodic peak current of low valence cobalt species increases, followed by a decrease in the corresponding cathodic current. This indicates that drugs are oxidized on the redox mediator which is immobilized on the electrode surface via an electrocatalytic mechanism. With the use of Laviron’s equation, the values of anodic and cathodic electron-transfer coefficients and charge-transfer rate constant for the immobilized redox species were determined as α _s,a = 0.72, α _s,c = 0.30, and k _s = 0.22 s⁻¹. The rate constant, the electron transfer coefficient, and the diffusion coefficient involved in the electrocatalytic oxidation of drugs were reported. It was shown that by using the modified electrode, aspirin and acetaminophen can be determined by amperometric technique with detection limits of 1.88 × 10⁻⁶ and 1.83 × 10⁻⁶ M, respectively. By analyzing the content of acetaminophen and aspirin in bulk forms using chronoamperometric and amperometric techniques, the analytical utility of the modified electrode was achieved. The method was also proven to be valid for analyzing these drugs in urine samples.     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Electrochemical behaviors of GMP based on solid-phase extractionon at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode

Guanosine-5′-monophosphate (GMP) was investigated the electrochemical behaviors based on solid-phase extractionon (SPE) at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode. Cu-Mg-Al hydrotalcite-like compound (HTLC) was proved as a new sorbent for SPE of GMP, which showed an irreversible adsorption oxidation process on the HTLC/GCE with the oxidation peak potential located at 1.15 V (vs. SCE) in a pH 5.0 acetate buffer solution. Influencing factors of the electrochemical behavior of GMP on the HLTC/GCE were optimized and kinetic parameters were calculated. Under the optimal conditions, with differential pulse voltammetry (DPV), a linear relationship was obtained between the oxidation peak current and the GMP concentration in the range from 1.0 × 10^− 6 to 8.0 × 10⁻⁴ mol L⁻¹ with the detection limit as 5.0 × 10⁻⁷ mol L⁻¹ (signal-to-noise ratio of 3). The modified electrode surface has very good reproducibility and stability.     

Selective determination of uric acid in the presence of ascorbic acid using a penicillamine self-assembled gold electrode

The electrochemical behaviors of uric acid (UA) at the penicillamine (Pen) self-assembled monolayers modified gold electrode (Pen/Au) have been studied. The Pen/Au electrode is demonstrated to promote the electrochemical response of UA by cyclic voltammetry (CV). The diffusion coefficient D of UA is 6.97 × 10⁻⁶ cm² s⁻¹. In differential pulse voltammetric (DPV) measurements, the Pen/Au electrode can separate the UA and ascorbic acid (AA) oxidation potentials by about 120 mV and can be used for the selective determination of UA in the presence of AA. The detection limit was 1 × 10⁻⁶ mol L⁻¹. The modified electrode shows excellent sensitivity, good selectivity and antifouling properties.     

Organosilica composite for preconcentration of phenolic compounds from aqueous solutions

A new adsorbent is proposed for the solid-phase extraction of phenol and 1-naphthol from polluted water. The adsorbent (TX-SiO₂) is an organosilica composite made from a bifunctional immobilized layer comprising a major fraction (91%) of hydrophilic diol groups and minor fraction (9%) of the amphiphilic long-chain nonionic surfactant Triton X-100 (polyoxyethylated isooctylphenol) (TX). Under static conditions phenol was quantitatively extracted onto TX-SiO₂ in the form of a 4-nitrophenylazophenolate ion associate with cetyltrimethylammonium bromide. The capacity of TX-SiO₂ for phenol is 2.4 mg g⁻¹ with distribution coefficients up to 3.4 × 10⁴ mL g⁻¹; corresponding data for 1-naphthol are 1.5 mg g⁻¹ and 3 × 10³ mL g⁻¹. The distribution coefficient does not change significantly for solution volumes of 0.025–0.5 L and adsorbent mass less than 0.03 g; 1–90 μg analyte can be easily eluted by 1–3 mL acetonitrile with an overall recovery of 98.2% and 78.3% for phenol and 1-naphthol, respectively. Linear correlation between acetonitrile solution absorbance (A ₅₄₀) and phenol concentration (C) in water was found according to the equation A ₅₄₀ = (6 ± 1) × 10⁻² + (0.9 ± 0.1)C (μmol L⁻¹) with a detection range from 1 × 10⁻⁸ mol L⁻¹ (0.9 μL g⁻¹) to 2 × 10⁻⁷ mol L⁻¹ (19 μL g⁻¹), a limit of quantification of 1 μL g⁻¹ (preconcentration factor 125), correlation coefficient of 0.936, and relative standard deviation of 2.5%. A solid-phase colorimetric method was developed for quantitative determination of 1-naphthol on adsorbent phase using scanner technology and RGB numerical analysis. The detection limit of 1-naphthol with this method is 6 μL g⁻¹ while the quantification limit is 20 μL g⁻¹. A test system was developed for naked eye monitoring of 1-naphthol impurities in water. The proposed test kit allows one to observe changes in the adsorbent color when 1-naphthol concentration in water is 0.08–3.2 mL g⁻¹.     

Langmuir–Blodgett film of tetraoxocalix[2]arene[2]triazine modified electrode for voltammetric determination of copper ion

In the present work, a new voltammetric sensor, Langmuir–Blodgett (LB) film of tetraoxocalix[2]arene[2]triazine (TOCT) modified glassy carbon electrode (LB_TOCT-GCE), for trace analysis of copper ion in water samples, was prepared. The morphology of LB_TOCT-GCE was characterized by cyclic voltammetric method, electrochemical impedance spectroscopy, and atomic force microscope. The recognizing mechanism of LB_TOCT-GCE for copper ion in aqueous solution was discussed. Under the optimum experimental conditions, using square wave stripping voltammetry and accumulation time of 300 s, the peak currents were linear relationship with Cu²⁺ concentrations in the range of 2 × 10⁻⁹ to 1 × 10⁻⁶ mol L⁻¹, with detection limit of 1 × 10⁻¹⁰ mol L⁻¹. By this method, real samples (lake water, drinking water, and city wastewater) were analyzed with satisfactory results. In addition, the fabricated electrode exhibited a distinct advantage of simple preparation, non-toxicity, good reproducibility, and stability.     

A new amperometric H<Subscript>2</Subscript>O<Subscript>2</Subscript> biosensor based on nanocomposite films of chitosan–MWNTs,hemoglobin, and silver nanoparticles

A new H₂O₂ biosensor was fabricated on the basis of nanocomposite films of hemoglobin (Hb), silver nanoparticles (AgNPs), and multiwalled carbon nanotubes (MWNTs)–chitosan (Chit) dispersed solution immobilized on glassy carbon electrode (GCE). The immobilized Hb displayed a pair of well-defined and reversible redox peaks with a formal potential (E ^θ′) of −22.5 mV in 0.1 M pH 7.0 phosphate buffer solution. The apparent heterogeneous electron transfer rate constants (k _s) in the Chit–MWNTs film was evaluated as 2.58 s⁻¹ according to Laviron’s equation. The surface concentration (Γ*) of the electroactive Hb in the Chit–MWNTs film was estimated to be (2.48 ± 0.25) × 10⁻⁹ mol cm⁻². Meanwhile, the Chit–MWNTs/Hb/AgNPs/GCE demonstrated excellently electrocatalytical ability to H₂O₂. Its apparent Michaelis–Menten constant (K _M^app) for H₂O₂ was 0.0032 mM, showing a good affinity. Under optimal conditions, the biosensors could be used for the determination of H₂O₂ ranging from 6.25 × 10⁻⁶ to 9.30 × 10⁻⁵ mol L⁻¹ with a detection limit of 3.47 × 10⁻⁷ mol L⁻¹ (S/N = 3). Furthermore, the biosensor possessed rapid response to H₂O₂ and good stability, selectivity, and reproducibility.     

Electrochemical Behavior of Uric Acid and Epinephrine at a Meso-2,3-Dimercaptosuccinic Acid Self-Assembled Gold Electrode

A self-assembled electrode with a meso-2,3-dimercaptosuccinic acid (DMSA) monolayer has been characterized by electrochemical quartz crystal microbalance and complex impedance analysis, surface enhanced Raman spectroscopy and cyclic voltammetry. The self-assembled electrode was used for the simultaneous electrochemical detection of epinephrine (EP) and uric acid (UA) in phosphate buffer of pH 7.7. The simultaneous oxidation of EP and UA was performed by cyclic voltammetry (CV) and differential pulse voltammetry (DPV), and the signals for each method were well separated with a potential difference of over 330 mV and without interference by each other. The detection limit of EP is 5.4 × 10⁻⁸ mol L⁻¹ by CV and 5.3 × 10⁻⁸ mol L⁻¹ by DPV and that of UA is 8.4 × 10⁻⁸ mol L⁻¹ by CV and 4.2 × 10⁻⁸ mol L⁻¹ by DPV. The DMSA self-assembled electrode can be applied to the simultaneous determination of EP and UA.