Determination of total phosphorus in water by photochemical decomposition with ultraviolet irradiation

A simple and convenient photochemical decomposition method has been developed for the determination of total phosphorus in natural and sewage water. Organic phosphorus compounds and inorganic polyphosphates may be completely converted into orthophosphate in the presence of 0.3M sulphuric acid and 0.12% potassium persulphate with 50 min irradiation. The relative standard deviations found for analysis of natural water (P 35 microg/l.) and sewage (P 2.4 mg/l.) were 5.7% and 1.0% respectively. The method gives results comparable to those obtained by digestion with persulphate.     

Determination of bromide, bromate and other anions with ion chromatography and an inductively coupled plasma mass spectrometer as element-specific detector

An implementation of the Dionex IonPac AS12A analytical column with an element-specific ICP-MS detection is described for the simultaneous determination of halogen and oxyhalogen anions, sulfate, phosphate, selenite, selenate and arsenate. The chromatographic separation was achieved in less than 4 min with an aqueous 11 mM (NH4)2CO3 (pH 11.2, adjusted with aqueous ammonia) as eluent. Special emphasis was given to optimize the ICP-MS detection conditions for the reliable detection (RSD<5%) of bromate and bromide at a bromine concentration level of 1.0 microg l(-1) with 50 microl sample injection volume. In order to achieve the highest detector response for bromine species an ultrasonic nebulizer equipped with a membrane desolvator had to be employed. The detection limits (S/N=3, sample injection volume 50 microl) obtained with the IC-ICP-MS after the optimization were 0.67 microg l(-1) for BrO3-, 0.47 microg l(-1) for Br-, 69 microg l(-1) for ClO2-, 4 microg l(-1) for Cl-, 47 microg l(-1) for ClO3-, 13 microg l(-1) for SO4(2-), 36 microg l(-1) for PO4(3-), 0.4 microg l(-1) for SeO3(2-), 0.3 microg l(-1) for SeO4(2-), and 0.4 microg l(-1) for AsO4(3-).     

Determination of chloride by displacement of hydrogen cyanide from mercury(II) cyanide

A method, based on the passivity of mercury(II) cyanide in dilute sulphuric acid and its reaction with hydrochloric acid to produce hydrogen cyanide, has been developed for the determination of small amounts of chloride. Hydrogen cyanide, distilled from a mercury(II) cyanide-halide-dilute sulphuric acid system is found by iodometric measurement to be directly proportional to the amount of chloride or bromide and of hydrogen ion in acids such as sulphuric acid. A linear correlation also holds for iodide but the stoichiometry is different, the titration values being about three times larger than expected. By conversion of the cyanide into a dye by means of the pyridine-pyrazolone reagent, 0.014-0.43 mug ml chloride concentrations have been determined. The method is also applicable to bromide and sulphuric acid in small amounts but not to fluoride and iodide. Results are reproducible to within +/-2%.     

Determination of bromide and nitrite by indirect redox titration using phenyl iodosoacetate

Bromide has been determined by its oxidation with an excess of phenyl iodosoacetate in the presence of acetanilide to give bromine which subsequently reacts with acetanilide to form 4-bromoacetanilide. The residual amount of phenyl iodosoacetate was evaluated iodometrically. Thus, for every mol of bromide one mol of phenyl iodosoacetate was consumed. For the determination of bromine in organic compounds, the test substance was decomposed by fusion with alkali peroxide to liberate bromide which was then evaluated by the phenyl iodosoacetate method. For its determination, nitrite has been reacted with an excess of isoniazid in acid medium to form isonicotinyl azide (which does not react with phenyl iodosoacetate) and the residual amount of isoniazid was titrated with phenyl iodosoacetate in the presence of acidified bromide and methyl red indicator (when isoniazid and phenyl iodosoacetate react in a 12 molar ratio). Each mol of nitrite is equivalent to 2 mol of phenyl iodosoacetate.     

Analysing fluorobenzoate tracers in groundwater samples using liquid chromatography-tandem mass spectrometry. A tool for leaching studies and hydrology

A sensitive LC-MS-MS method for the direct determination and quantification of 15 fluorobenzoic acids (FBAs) was developed. FBAs are used as conservative tracers for hydrological modelling of water flow and in studies of pesticides and other xenobiotic compounds. The use of FBAs is discussed in relation to other tracers (bromide, chloride, uranine). The method covers mono-substituted fluorobenzoic acid, difluorobenzoic acid, trifluorobenzoic acid, and tetrafluorobenzoic acid. The general detection limit in ground water was 1 microg/l using electrospray ionisation and 20 microg/l using atmospheric pressure chemical ionisation. Analysis time was less than 10 min, small sample volumes were needed and no clean-up was required.     

Fluorimetric determination of boron at microgram level

The synthesis, characterization and application of 2-(2-hydroxybenzylidenimine)benzene-arsonic acid (HBBA) as a reagent for the fluorimetric determination of boron are described. This reagent reacts with boric acid in 85% w/w sulphuric acid medium to yield a fluorescent compound. The reagent is not fluorescent in those conditions. Heating at 90 degrees for 45 min is needed for the compound to be formed. The linear calibration range is 0.1-8 microg/ml in the solution measured. The detection limit of the method is 0.01 microg/ml. The method has been applied to determine boron in vegetal material.     

Flow-injection extraction spectrophotometric determination of bismuth as tetraiodobismuthate(III) with the tetramethylenebis(triphenylphosphonium) cation

Bismuth can be determined spectrophotometrically at 495 nm after its extraction as tetramethylenebis(triphenylphosphonium) tetraiodobismuthate(III) into dichloromethane. The carrier stream is 2 M sulphuric acid and the reagent stream contains 2% (w/v) potassium iodine and 0.4% (w/v) tetramethylenebis(triphenylphosphonium) bromide. The injection rate is 20 h^-1. The calibration graph is linear up to 20 μ ml^-1 bismuth and the detection limit is 0.24 μ ml^-1 bismuth, based on injection volumes of 250μl. The system has been applied to determination of bismuth in pharmaceutical samples.     

Simultaneous Determination of Micro Bromide and Iodide by Kinetic Spectrophotometric Method

ABSTRACT

ABSTRACTA new kinetic spectrophotometric method for the simultaneous determination of concentrations of micro bromide and iodide has been proposed. It is based on their catalytic effects on the reaction of m-cresol purple oxidized by potassium periodate in hydrochloride acid medium. The reaction rate was monitored by measuring the decrease in absorbance at 528nm and the increase in absorbance at 455nm. The total difference in absorbance of the sum of bromide and iodide is identical with determination of bromide was carried out after Cr(VI) oxidized I? to I₂, and I₂ was removed by extraction with CCI₄, and the amount of iodide was measured by subtracting the absorbance change of bromide from the total absorbance change in the presence of bromine and iodide. The optimum conditions influencing the reaction rate were studied. The linear range of determination is 0～4.0μg/ml for Br? and 0～3.0 μg/ml for I?. The detection limits are 0.032μg/ml for Br? and 0.059 μ/ml for I?. The method was successfully applied to the determination of micro amounts of bromide and iodide in food and life samples.     

Flow-injection extraction spectrophotometric determination of dichromate with the tetramethylenebis(triphenylphosphonium)cation

Chromium(VI) (0–5 μg) can be determined spectrophotometrically at 365 nm after flow-injection extraction into chloroform of the ion-associate, tetramethylenebis(triphenylphosphonium) dichromate. The carrier stream is distilled water and the reagent stream contains 1 M sulphuric acid and 0.5% (w/v) tetramethylenebis(triphenylphosphonium) bromide. The sampling rate is 24 h^?1. The calibration graph is linear up to 20 μg ml^?1 and the detection limit is 0.44 μg ml?1 chromium, based on injection volumes of 250 μl. The system has been applied to the determination of chromium in a range of steels.     

Determination of milk-oxidised ketone bodies as an acetone derivative by electron capture gas chromatography

Following the deproteination of the milk sample by means of zinc hexacyanoferrate, acetoacetic acid was decarboxylated by heating; the acetone originally present was then determined together with the acetone formed. The essence of the determination was that acetone reacted with bromine in the presence of sulphuric acid, following which, the bromoacetone formed was extracted into toluene, separated by gas chromatography and measured using an electron capture detector. The calibration curve was found to be linear up to a concentration of 2 mmol l(-1) acetone. The detection limit calculated from the threefold noise level and the slope of the calibration curve was 9x10(-7) mol l(-1). The reliability of the method meets the practical requirements. Its application may be recommended above all for the establishment of subclinical ketosis.     

Extraction of prussian blue into chloroform in the presence of ajatin

Extraction of Prussian Blue into chloroform in the presence of ajatin (dimethyl-lauryl-benzylammonium bromide) is proposed for the concentration and determination of ferrocyanide ion. Optimum concentrations of sulphuric acid and of ajatin have been established and the selectivity of the extraction has been investigated. Ways of eliminating some interferences are discussed.     

Determination of low levels of bromide in fresh water after chromatographic enrichment

A method has been developed for the determination of bromide in fresh water. The analyte is enriched on the anion-exehanger Dowex 1 x 8, which exhibits a considerably greater affinity for bromide than for the major anions in fresh water. Sodium perchlorate is used as eluent and an enrichment factor of ~100 can be achieved. The eluted bromide is oxidized with peroxodisulphate to bromate, which is determined iodometrically by a previously published spectrophotometric method. The enrichment in the presence of the major components of fresh water has been studied. Only bicarbonate has been found to interfere, but this interference can be avoided by acidifying the sample with hydrochloric acid. The recovery from synthetic fresh water with ionic concentrations corresponding to 0.005 equivalent/l. and spiked with bromide was 100% at bromide concentrations larger than 50 nM (4 mug l. ) and about 90% at 10 nM. The detection limit is 1.5nM and the limit of determination 5nM for 1-litre samples.     

On-line speciation of bromine and bromide using sequential injection analysis with spectrophotometric detection

An on-line procedure for the simultaneous determination of bromine and total bromine (bromine+bromide oxidised to bromine) is proposed, which lead to the determination of bromide by subtraction. Phenol red was used as chromogenic reagent for bromine and total bromine after bromide was oxidised to bromine by Chloramine T. The linear range found is 1-10 mg L(-1) with a detection limit of 0.6 mg L(-1) for bromine, and a linear range of 0.8-15 mg L(-1) with a detection limit of 0.4 mg L(-1) for total bromine. The calculated RSD for bromine is less than 0.8% and for total bromine less than 0.7%. The system is fully computerised and able to run 30 samples per hour with an automated rinsing step that eliminates sample carry-over. The results for both bromine and bromide from the proposed sequential injection analysis (SIA) system compare favourably with standard manual methods and statistical evaluation proves no significant difference between the results of the proposed SIA system and the standard method at the 95% confidence level. The presence of other halides was found not to interfere.     

A modified method for the determination of methylmercury by gas chromatography

A simple modification of the West?? extraction procedure for methylmercury and its determination by gas chromatography (GC) is presented. The cysteine clean-up step has been modified, with use of cysteine-impregnated paper instead of cysteine solution. Methylmercury bromide is extracted from the sample into toluene and is selectively adsorbed on the cysteine paper. Interfering compounds are washed from the paper with toluene. The isolated methylmercury is set free with sulphuric acid containing bromide, extracted into benzene and determined by GC. The modification of the extraction procedure results in good recovery and reproducibility for various biological and environmental samples, good sensitivity with a detection limit of 0.1 ng/g, avoidance of difficulties arising from emulsion formation, cleaner chromatograms, and faster analysis. It is particularly suitable for determination of low levels of MeHg.     

Oxidimetric determination of thiourea, thiosulphate and sulphite with thallic perchlorate in acid medium

Conditions have been established for the titrimetric estimation of thiourea, thiosulphate and sulphite with thallic perchlorate, with visual end-points, in perchloric and sulphuric acid medium. In the direct determination, chloride and bromide interfere. In the indirect iodometric determination. Cu(2+) and Fe(2+) interfere, but chloride and bromide do not.     

Determination of nitrite and mixtures of bromide and iodide with o-iodosobenzoate

Nitrite diazotizes sulphanilamide, which then does not undergo 3,5-dibromination. Nitrite can therefore be determined by reaction with excess of sulphanilamide, the surplus of which is then titrated with o-iodosobenzoate or chloramine-T in the presence of potassium bromide, with Methyl Red as indicator. Mixtures of iodide and bromide can be analysed by oxidation of the iodide with excess of o-iodosobenzoate at pH 4-6, followed by extraction of the iodine (which is then titrated with thiosulphate) and then oxidation of the bromide in dilute sulphuric acid medium in the presence of sulphanilamide as bromine scavenger, the residual oxidant being evaluated iodometrically.     

Liquid-phase microextraction-gas chromatography-mass spectrometry for the determination of bromate, iodate, bromide and iodide in high-chloride matrix

In the determination of bromate and iodate, any free bromide and iodide present was quantitatively removed by anion exchange with silver chloride exploiting the differences in silver salts solubility product, being AgCl, 1.8 x 10(-10), AgBr, 5.0 x 10(-13), AgI, 8.3 x 10(-17), AgBrO(3), 5.5 x 10(-5) and AgIO(3), 3.1 x 10(-8). The oxyhalides were reduced with ascorbic acid to halides and converted to 4-bromo-2,6-dimethylaniline and 4-iodo-2,6-dimethylaniline by their reaction with 2-iodosobenzoate in the presence of 2,6-dimethylaniline at pH 6.4 and 2-3, respectively. Single drop microextraction (SDME) of the haloanilines in 2 microl of toluene and injection of the whole extract into GC-MS, or liquid-phase microextraction (LPME) into 50 microl of toluene and injection of 2 microl of extract, resulted in a sensitive method for bromate and iodate. The latter method of extraction has been found more robust, sensitive and to give better extraction in shorter period than SDME. Total bromine/iodine was determined without any treatment with silver chloride. High concentration of chloride in the matrix did not interfere. A rectilinear calibration graph was obtained for 0.05 microg-25 mg l(-1) of bromate/bromide and iodate/iodide, the limit of detection were 20 ng l(-1) of bromate, 15 ng l(-1) of iodate, 20 ng l(-1) of bromide and 10 ng l(-1) of iodide (by LPME in 50 microl of toluene). The method has been applied to seawater and table salt. From the pooled data, the average recovery of spiked oxyhalide/halide to real samples was in range 96.7-105.7% with RSD in range 1.6-6.5%.     

Determination of poly-beta-hydroxybutyric acid in Bacillus thuringiensis by capillary zone electrophoresis with indirect ultraviolet absorbance detection

A new capillary electrophoresis method for determining poly-beta-hydroxybutyric acid (PHB) in Bacillus thuringiensis was established. Poly-beta-hydroxybutyric acid in samples was hydrolyzed by sulphuric acid and neutralized by Ba(OH)2. The content of produced beta-hydroxybutyrate was then determined by capillary zone electrophoresis (CZE) with indirect UV detection at 254 nm. With 5 mM p-hydroxybenzoate and 0.5 mM tetradecyltrimethylammonium bromide (TTAB) at pH 8.0 as carrier electrolyte, beta-hydroxybutyrate can be determined within 6 min. Standard regression equation was made by beta-hydroxybutyrate, and the linear range was 2-1000 microg/ml. The relative standard deviations (RSDs) for migration time and peak area are both less than 1.0%. The detection limit for beta-hydroxybutyrate was 0.2 microg/ml, which is two to three orders of magnitude lower than that of the gas chromatography (GC) method. The capillary electrophoresis method was successfully applied to determine poly-beta-hydroxybutyric acid in fermentation broth and single colony. The added standard recovery was 96%.     

恒电流库仑分析法测定乙烯基三乙氧基硅烷

建立了恒电流库仑分析法测定乙烯基三乙氧基硅烷(VTES)含量的方法. 探讨了电解液、反应时间、极化电位、溶剂等因素对测定的影响. 结果表明, 选用V(甲酸)∶V(KBr (2 mol/L))∶V(乙醇)＝6∶1∶3为电解液, 极化电位为200 mV, VTES与溴的四氯化碳溶液反应30 min, 甲醇为VTES的溶剂时测定结果最佳. 该方法用于样品VTES的测定, 加标回收率为98.4%～102.7%, 相对标准偏差为1.7%.     

Coulometric titration with electrogenerated +2 tin: Determination of iodine,bromine, and various oxidants via iodometry

The use of electrolytically generated +2 tin as a coulometric titrant has been studied. In a 3 to 4M sodium bromide and 0.2N hydrochloric acid solution, containing 0.2M stannie chloride, the generation of stannous ion is 100% efficient up to a current density of 80 mA/cm². With this medium iodine and bromine can be titrated coulometrically with errors of about ±0.3% or less. The titration is well suited for the iodometric determination of strong oxidants. Employing stannous ion and bromine for direct and reverse titrations, quinone and hydroquinone have been titrated.