小阻尼界面房间声传输函数和声脉冲响应函数的有限元素法

有限元法可用于以声波动方程为基础通过数值计算求解室内声场,适用于分析界面阻抗非均匀分布和复杂形状房间内声场的低频特性。本文首先介绍了小阻尼界面条件下室内声场简正方式、声衰变系数、混响时间的ＦＥＭ计算方法。在此基础上导出了房间内两点之间声传输函数和声脉冲响应函数的ＦＥＭ计算模型,并以矩形房间为例详细讨论了有关细节。本文所讨论的计算模型可以映房间内不同的声源点,接收点位置上的声压频谱特性和脉冲响应的时     

采用M序列相关法测量材料界面的声散射特性

用Ｍ序列进行材料方向性声散特性的测量,其基本思路是以伪随机Ｍ序列作为测试信号利用相关的方法测得系统的脉冲响应,根据直达声和各次反射声到达时间加以相应的窗隔离出散射脉冲信号,再进行方向性对比。本文介绍了测量的基本原理和应注意的问题,并给出了一个具体的测量系统实验典型。     

半导体超晶格界面声子的拉曼散射与对界面本质的认识

介绍了对半导体超晶格中宏观和微观两种界面声子研究的最新结果，深入讨论了这些新结果的物理意义，以及有待进一步研究的问题 。     

低频室内声散射计算机模拟方法

近年来,声散射的模拟成为室内声场计算机模拟研究的重点。现有的方法一般是依据壁面性质(结构、粗糙度等),利用经验确定散射系数,并基于该系数来模拟室内散射声能的分布。这种方法在低频情况下的精度较差,主要原因是忽略了在低频声场中起重要作用的波动现象。为此,本文提出一种新的计算壁面散射的模型,该模型既可考虑壁面上产生的散射声能,又可计算因壁面边缘衍射而产生的散射声能。文中通过模拟和实测数据的对比,分析验证了该模型的有效性,并给出了表面散射系数的取值规则。     

多重随机声散射模型及计算机仿真

声波在室内的传播过程是很复杂的,尤其是当室内有许多家具和机器设备时。要经历由上述物体引起的多重散射过程。本文提出的多重随机声散射模型及相应的计算机仿真程序,较全面地描述了声波在室内的复杂散射、反射与吸收,与实测结果相比较,具有良好的精度,能较为精确地预测声能在空间的分布,可用于厂房、办公室等的噪声控制,在室内音质设计实践中也具有广泛的应用前景。     

考虑界面状况时柱状弹性固体的声波散射

导出了求解母材料固体中镶嵌的柱状弹性固体(两固体间存在界面薄层)声波散射系数的一般表达式.根据Flax的共振散射理论,对背向散射谱中的共振模式进行了识别.利用模拟界面薄层的弹簧模型,考察了界面层切向劲度常数K_T对共振模式形态的影响关键词：声波散射共振模式界面     

相干声线跟踪理论中的周期界面迭代散射 仿真方法*

界面声反射模拟是室内复杂声学现象仿真的关键。针对传统声学仿真方法对于周期散射结构存在条件下声场仿真精度较低的问题,本文发展了一种基于迭代散射模型的室内相干声线跟踪法。此方法以经典的相干声线跟踪法为基础,将室内中常见的周期散射结构进行几何形状上的简化处理,然后依据周期散射定理给出声波在界面上的散射方向及能量,并将原始声线迭代分裂为相应的散射子声线,继续对其跟踪处理,此迭代散射模型对周期散射结构上的界面散射现象进行了准确的模拟。数值验证结果表明,本文方法可以有效地在低频段提高室内声场仿真精度,可为具有复杂散射现象的室内仿真提供新思路。     

柱状分层固体媒质的声散射

本文评述了各向同性和横向各向同性柱状分层固体声散射理论和实验研究进展 ,介绍了描述圆柱状界面薄层特性的弹簧模型 ,也讨论了该领域中有待进一步研究的一些问题。     

金属中表面和界面散射的量子力学处理

中图分类号:     

考虑超声探测器脉冲响应和方向性的光声图像重建方法

在光声成像中,假设超声探测器为具有全向响应的理想点探测器通常会导致图像分辨率下降。为了解决探测器效应引起的图像质量下降问题,提出一种考虑探测器特性的光声图像重建方法,建立包含探测器方向性和脉冲响应的前向成像模型,通过迭代求解前向模型的逆问题,实现光吸收能量分布图的高质量重建。仿真和仿体实验结果表明,与未考虑或未充分考虑探测器特性的传统重建方法和其他重建增强方法相比,所提方法可以显著提高图像分辨率和对比度,改善图像质量。     

重放自由场虚拟源距离信息的动态双耳Ambisonics方法

提出了一种面向虚拟现实应用场景的房间脉冲响应计算模型, 将深度学习神经网络技术与心理声学感知参数结合, 能够高效地从虚拟现实场景信息中预测具有听觉感知意义的房间脉冲响应。在确保高质量预测结果的同时, 该模型可以满足虚拟现实音频场景中生成房间脉冲响应所需的实时性、高采样率、非受限长度和轻量化的要求。模型首先通过图卷积神经网络将场景中的声学信息编码, 然后通过神经声场与转置卷积模型将声学信息解码得到房间脉冲响应感知参数, 最后根据房间脉冲响应感知参数恢复出房间脉冲响应信号。实验结果表明, 所提模型在房间脉冲响应生成质量、计算开销以及功能性方面都有较大的优势, 可较好地满足虚拟现实音频对于实时生成房间脉冲响应的需求。

     

A hybrid MLS technique for room impulse response estimation

The measurement of room impulse response (RIR) when there are high background noise levels frequently means one must deal with very low signal-to-noise ratios (SNR). If such is the case, the measurement might yield unreliable results, even when synchronous averaging techniques are used. Furthermore, if there are non-linearities in the apparatus or system time variances, the final SNR can be severely degraded. The test signals used in RIR measurement are often disturbed by non-stationary ambient noise components. A novel approach based on the energy analysis of ambient noise - both in the time and in frequency - was considered. A modified maximum length sequence (MLS) measurement technique, referred to herein as the hybrid MLS technique, was developed for use in room acoustics. The technique consists of reducing the noise energy of the captured sequences before applying the averaging technique in order to improve the overall SNRs and frequency response accuracy. Experiments were conducted under real conditions with different types of underlying ambient noises. Results are shown and discussed. Advantages and disadvantages of the hybrid MLS technique over standard MLS technique are evaluated and discussed. Our findings show that the new technique leads to a significant increase in the overall SNR.     

A comparison of measured room acoustics metrics using a spherical microphone array and conventional methods

The traditional microphone configuration used to measure room impulse responses (IRs) according to ISO 3382:2009 is an omnidirectional and figure-8 microphone pair. IRs measurements were taken in a 2500-seat auditorium to determine how the results from a spherical microphone array (an mh acoustics Eigenmike-em32) compare to those from the traditional microphone setup (a Brüel & Kjær Type-4192 omnidirectional microphone and a Sennheiser MKH30 figure-8 microphone). Measurements were obtained at six receiver locations, with three repetitions each in order to first evaluate repeatability. The metrics considered in this study were: reverberation time (T30), early decay time (EDT), clarity index (C80), strength (G), lateral energy fraction (J_LF) and late lateral energy level (L_J). Before calculating these quantities, the IRs were filtered to equalize the frequency response of the microphones and sound source. For the spherical array measurements, the omnidirectional (monopole) and figure-8 (dipole) patterns were extracted using beamforming. In terms of repeatability, the average standard deviation of the three measurements at each receiver location averaged across all metrics, receivers, and octave bands was found to be 0.01 just noticeable differences (JNDs). The analysis comparing the measurements from the two microphone configurations yielded differences which were less than 1 JND for the majority of metrics, with a few exceptions of EDT and C80 slightly above 1 JND. Based on this case study, these results indicate that spherical microphone arrays can be used to obtain valid room IR measurements, which will allow for the development of new metrics utilizing the higher spatial resolution made possible with spherical arrays.     

A hybrid model for the acoustic response of a two-dimensional rough surface to an impulse incident from a refracting medium

A numerical model to calculate the impulse response of a two-dimensional, impenetrable, rough surface directly in the time domain has been recently introduced [J. Acoust. Soc. Am. (2000) 107, 27]. This model is based on wedge diffraction theory and assumes that the half-space containing the source and receiver is homogeneous. In this work, the model is extended to handle media where the index of refraction varies with the distance to the surface by merging the scattering model with a ray-based propagation model. The resulting hybrid model is tested against a Finite-Difference Time-Domain (FDTD) method for the problem of backscattering from a corrugated surface in the presence of a refractive layer. This new model can be applied, for example, to calculate acoustic reverberation from the sea surface in cases where the water mass is inhomogeneous and in the presence of a subsurface bubble layer at low frequencies where dispersion is negligible. It can also be used for atmospheric propagation problems where there is a sound speed gradient overlying rough terrain.     

虚拟声技术及其应用(上)

本文综述了虚拟声技术及其应用。在简单回顾了有关虚拟声的心理声学基础后，论述和分析了耳机和扬声器重发虚拟声的基本原理和基本的缺陷，总结了近年所提出的虚拟声的改进方法，最后探讨了虚拟声在科学研究、工程技术和消费电子领域的各种应用。     

About the nature of increase of the nonlinear optical response of a rough surface

It is shown that during the propagation of surface plasmon polariton (SPP) in the system of two touching spheres (or cones) when one is a metal and the other is a semiconductor, the conditions of strong localization of the surface wave are realized. At the point of contact, an essential decrease of the wavelength of the SPP is observed and the diffraction processes do not hinder its localization on the nanometric scale. As a result, wave fields increase anomalously. The considered phenomena open a new possibility to propose the experimental way for exploring the gigantic enhancement of the nonlinear optical response from a rough surface.     

高光洁度玻璃基片的表面散射和体散射测量

 提出了一种利用总积分散射（TIS）测量K9玻璃基片表面散射和体散射的实验方法。首先采用磁控溅射技术在基片表面沉积厚度为几十nm的金属Ag薄膜,然后将基片的表面和体区分开考虑,通过TIS测得了基片上下表面的均方根粗糙度, 进而求得基片的总散射和表面散射,最后计算得到了体散射。分别利用TIS和原子力显微镜（AFM）测量了3个样品上表面所镀Ag膜的均方根粗糙度,两种方法所得的均方根粗糙度的数值相差不明显,差值分别为0.08,0.11和0.09 nm, 表明TIS和AFM的测量结果相一致。利用该方法测得3块K9玻璃基片的总散射分别为6.06×10^-4,5.84×10^-4和6.48×10^-4,表面散射介于1.25×10^-4~1.56×10^-4之间,由此计算得到的体散射分别为3.10×10^-4,3.30×10^-4和3.61×10^-4。     

多通路空间声的前方四扬声器局域Ambisonics信号馈给法*

典型的多通路空间声扬声器布置一般包含水平面左前、右前,高仰角左前上、右前上四个方向的扬声器。 本文提出一种利用该四个扬声器产生前方水平与垂直方向虚拟源的一阶局域Ambisonics 信号馈给法。该信号馈给法是通过对目标和重放声场进行球谐函数展开并取一阶近似得到。采用简化的头部模型和精确的头相关传输函数模型分析表明,一阶局域Ambisonics 信号馈给法可以产生合适的低频听觉定位因素,包括双耳时间差及其随头部转动的动态变化。虚拟源定位实验结果表明,该方法可以在扬声器布置的范围内,甚至在略超出扬声器布置的范围内产生不同方位角和仰角的虚拟源。因而本文的方法可用在多通路空间声重放中产生与图像配合的虚拟源定位效果。     

改进的5.1通路环绕声三扬声器虚拟重发系统

提出一种改进的5．1通路环绕声的三扬声器虚拟重发系统。本文首先指出,现有的两扬声器虚拟重发存在听音区域窄、声像稳定性差等缺陷。通过理论分析和心理声实验证明,采用一对布置在前方±30°的全频带扬声器和一个前方0°的高频中置扬声器组成5．1通路环绕声虚拟重发系统,不但可提高重发声像的稳定性,且扬声器布置实际可行,信号处理相对简单。因此所提出的虚拟系统及其扬声器布置是适合于电视和多媒体计算机的应用。     

动态光散射实验中散射光偏振状态的研究

颗粒散射光的偏振状态对提高动态光散射实验系统空间相干性和测量结果正确性有着重要影响,因此研究散射光的偏振状态具有重要现实意义的。本文利用米散射理论分析了入射光与散射光偏振状态之间的关系,在此基础上揭示了在动态光散射中使用垂直偏振光作为入射光的理论依据,并在实验中验证了上述理论的正确性。