Thermal analyis of hexadecyltrimethylammonium–montmorillonites

Na-montmorillonite (Na-MONT) was loaded with hexadecyltrimethylammonium cations (HDTMA) by replacing 41 and 90% of the exchangeable Na with HDTMA, labeled OC-41 and OC-90, respectively. Na-MONT, OC-41, and OC-90 were heated in air up to 900 °C. Unheated and thermally treated organoclays heated at 150, 250, 360, and 420 °C are used in our laboratory as sorbents of different hazardous organic compounds from waste water. In order to get a better knowledge about the composition and nature of the thermally treated organoclays Na-MONT and the two organo-clays were studied by thermogravimetry (TG) in air and under nitrogen. Carbon and hydrogen contents in each of the thermal treated sample were determined and their infrared spectra were recorded. The present results showed that at 150 °C both organoclays lost water but not intercalated HDTMA cations. At 250 °C, many HDTMA cations persisted in OC-41, but in OC-90 significant part of the cations were air-oxidized into H₂O and CO₂ and the residual carbon formed charcoal. After heating both samples at 360 °C charcoal was present in both organo clays. This charcoal persisted at 420 °C but was gradually oxidized by air with further rise in temperature. TG runs under nitrogen showed stepwise degradation corresponding to interlayer water desorption followed by decomposition of the organic compound, volatilization of small fragments and condensation of non-volatile fragments into quasi-charcoal. After dehydroxylation of the clay the last stages of organic matter pyrolysis and volatilization occurred.     

Thermal analysis of tetraethylammonium and benzyltrimethylammonium montmorillonites

Na-montmorillonite was loaded with tetraethylammonium cations (TEA) or with benzyltrimethylammonium cations (BTMA) by replacing 77 and 81% of the exchangeable Na with TEA or BTMA, labeled TEA-MONT and BTMA-MONT, respectively. TEA- and BTMA-MONT were heated in air up to 900?°C. Thermally treated organoclays are used in our laboratory as sorbents of organic compounds from water. The two organoclays were studied by TG and DTG in air and under nitrogen. Carbon content in each of the heated sample was determined. They were diffracted by X-ray, and fitting calculations of d(001) peaks were performed on each diffractogram. TG and thermo-C analysis showed that at 150 and 250?°C both organoclays lost water but not intercalated ammonium cations. DTG peak of the first oxidation step of the organic cation with the formation of low-temperature stable charcoal (LTSC) appeared at 364 and 313?°C for TEA- and BTMA-MONT, respectively. The charcoal was gradually oxidized by air with further rise in temperature. DTG peak of the second oxidation step with the formation of high-temperature stable charcoal (HTSC) appeared at 397 and 380?°C for TEA- and BTMA-MONT, respectively. DTG peak of the final oxidation step of the organic matter appeared at 694 and 705?°C for TEA- and BTMA-MONT, respectively, after the dehydroxylation of the clay. Thermo-XRD analysis detected TEA-MONT tactoids with spacing 1.40 and 1.46?nm up to 300?°C. At 300 and 360?°C, LTSC-MONT tactoids were detected with spacing of 1.29?nm. At higher temperatures, HTSC-MONT-?? and -?? tactoids were detected with spacings of 1.28 and 1.13?nm, respectively. BTMA-MONT tactoids with spacings 1.46 and 1.53?nm were detected up to 250?°C. At 300 and 360?°C, LTSC-MONT tactoids were detected with a spacing of 1.38?nm. At higher temperatures, HTSC-MONT-?? and -?? tactoids were detected with spacings of 1.28 and 1.17?nm, respectively. At 650?°C, both clays were collapsed. HTSC-??-MONT differs from HTSC-??-MONT by having carbon atoms keying into the ditrigonal holes of the clay-O-planes. At 900?°C, the clay fraction is amorphous. Trace amounts of spinel and cristobalite are obtained from thermal recrystallization of amorphous meta-MONT.     

Secondary adsorption of nitrobenzene and m-nitrophenol by hexadecyltrimethylammonium-montmorillonite thermo-XRD-analysis

In the present research we studied the effect of the solvent used, whether it was polar water or a non-polar organic solvent (n-hexane or n-hexadecane), on the basal-spacing and bulk structure of the sorbate-sorbent complexes obtained by the secondary adsorption of nitrobenzene and m-nitrophenol by two types of organo-montmorillonites. X-ray measured basal spacings before and after thermal treatments up to 360°C. The organo-clays were synthesized, with 41 and 90% replacement of the exchangeable Na⁺ by hexadecyltrimethylammonium (HDTMA), with mono-and bilayers of HDTMA cations in the interlayer space, labelled OC-41 and OC-90, respectively. After heating at 360°C both organo-clays showed spacing at 1.25–1.28 nm, due to the presence of interlayer-charcoal, indicating that in the preheated organo-clays the HDTMA was located in the interlayer. The thermo-XRD-analysis of Na-clay complexes showed that from organic solvents both sorbates were adsorbed on the external surface but from water they were intercalated. m-Nitrophenol complexes of both organo-clays obtained in aqueous suspensions contain water molecules. Spacings of nitrobenzene complexes of OC-41 and OC-90 and those of nitrophenol complexes of OC-41 showed that the adsorbed molecules were imbedded in cavities in the HDTMA layers. Adsorption of m-nitrophenol by OC-90 from water and n-hexane resulted in an increase of basal spacing (0.21 and 0.29 nm, respectively) suggesting the existence of a layer of nitrophenol molecules sandwiched between two parallel HDTMA layers.     

Organoclays from alkaline-treated acid-activated clays

The cetyltrimethylammonium hydroxide (C16TMAOH) solution was proposed for the preparation of organoclays. Montmorillonite clay was acid activated at different acid/clay (a/c) (in mass) ratios, then treated with alkaline (sodium hydroxide) solution before being reacted with C16TMAOH solution. The acid activation caused a reduction in the number of cation exchange sites, and hence improved the exfoliation of the silicate sheets at higher pH values. The basal spacing increased significantly from 2.20 to 4.01 nm, and depended on the a/c ratios. The acid-activated clays with a/c ratios greater than 0.3 adsorbed significant amounts of C16TMA cations with a basal spacing of 4.01 nm compared with the non-acid-activated montmorillonite (2.51 nm). Meanwhile, the treatment of NaOH solution yielded clays with similar properties to that of the raw used clay. The XRF data, FT-IR, and ²⁹Si MAS-NMR techniques confirmed that the resulting amorphous silica during the acid activation was dissolved, and accompanied by a dramatical reduction in the surface areas. Similar amounts of C16TMA cations were adsorbed, i.e., close to 1 mmol g^?1, with a single basal spacing of 2.52 nm, independently of the treated acid-activated clays. The in-situ powder XRD studies revealed that an increase of the basal spacing to 4.20 nm was observed at intermediate temperatures ranging from 50 to 150 °C for organo-acid-activated clays with basal spacing of 4.01 nm, while a continuous decrease of the basal spacing was observed for organoclays with a basal spacing of 2.52 nm. At higher temperatures greater than 250 °C, the decomposition of the surfactant occurs, and the basal spacing decreases to a value of about 1.4 nm.     

Thermo-XRD-analysis of Co-, Ni- and Cu-montmorillonite treated with anionic alizarinate

Co- and Ni-montmorillonites adsorb in aqueous suspensions up to 13 mmol alizarinate per 100 g clay, onto the broken-bonds whereas Cu-clay adsorbs up to 25 mmol dye per 100 g clay into the interlayer space. Unloaded Co-, Ni- and Cu-clays and samples loaded with increasing amounts of alizarinate, were gradually heated in air to 360°C and analyzed by X-ray diffraction. All diffractograms were curve-fitted. Fitted diffractograms of non-heated samples, showed two peak components labeled C and D, at<span lang=EN-US style='font-size:10.0pt;font-family:Symbol;mso-bidi-font-family: Symbol;mso-ansi-language:EN-US'>?1.22 and<span lang=EN-US style='font-size:10.0pt;font-family:Symbol;mso-bidi-font-family: Symbol;mso-ansi-language:EN-US'>?1.32 nm, characterizing tactoids with mono- and non-complete bilayers of water, respectively. After heating at 120°C component D decreased or disappeared and two new components A and B appeared at<span lang=EN-US style='font-size:10.0pt;font-family:Symbol;mso-bidi-font-family:Symbol; mso-ansi-language:EN-US'>?0.99 and<span lang=EN-US style='font-size:10.0pt;font-family:Symbol;mso-bidi-font-family: Symbol;mso-ansi-language:EN-US'>?1.08 nm, representing collapsed tactoids and tactoids with interlamellar oxy-cations, respectively. At 250°C, C and D decreased or disappeared but A and B appeared in all fitted diffractograms. Co- and Ni-clay after heating at 360°C did not show C and D. Components A and B proved that these clays collapsed indicating that initially there was no alizarinate in the interlayers. At 360°C, C and D persisted in the fitted-diffractograms of Cu-clay, representing tactoids with interlamellar charcoal formed from the partial oxidation of adsorbed dye initially located in the interlayers.     

Thermo-X-ray-diffraction analysis of dimethylsulfoxide-kaolinite intercalation complexes

DMSO-kaolinite complexes of low- and high-defect Georgia kaolinite (KGa-1 and KGa-2, respectively) were investigated by thermo-XRD-analysis. X-ray patterns showed that DMSO was intercalated in both kaolinites with a d(001)-value of 1.11 nm (type I complex). The samples were gradually heated up to 170°C and diffracted by X-ray at room-temperature. With the rise in temperature, due to the thermal evolution of the guest molecules, the relative intensity of the 1.11 nm peak decreased and that of the 0.72 nm peak (neat kaolinite) increased indicating that the fraction of the non-intercalated tactoids increased. The 1.11 peak disappeared at 130–140°C. During the thermal treatment of both complexes two additional peaks appeared at 110 and 120°C, respectively, with d-values of 0.79–0.94 and 0.61–0.67 nm in DMSO-KGa-1 and 0.81–0.86 and 0.62–0.66 nm in DMSO-KGa-2, indicating the formation of a new phase (type II complex). The new complex was obtained by the dehydration of type I complex and was composed of intercalated DMSO molecules which did not escape. The new peaks disappeared at 150–160°C indicating the complete escape of DMSO.     

Fabrications of Nb-doped TiO<Subscript>2</Subscript> (TNO) transparent conductive oxide polycrystalline films on glass substrates by sol–gel method

Anatase Ti_0.94Nb_0.06O₂ (TNO) films were fabricated on glass substrates by sol–gel method using a dip-coating technique. The annealing treatment was separated into two steps, first in air at 350–550 °C for 1 h and then in vacuum of 4.0 × 10⁻⁴ Pa at 550 °C for 1 h. The influence of vacuum annealing treatment to the electrical and optical properties was discussed. Especially, the role of air annealing treatment from 350 to 550 °C on the crystallization and the structure of the films was analyzed. It is proved that the films annealed at 550 °C in air and then 550 °C in vacuum exhibited the minimum resistivity of 19.3 Ω·cm and the average optical transmittance of about 75% in the visible range, indicating that the sol–gel method is a feasible and promising method to fabricate TNO films.     

Mild pre-heating of organic cation-exchanged clays enhances their interactions with nitrobenzene in aqueous environment

Aqueous sorption kinetics and equilibrium isotherms of nitrobenzene were studied on two series of sorbents that were prepared by (i) replacing inorganic exchangeable cations in Wyoming bentonite with tetraethylammonium (TEA) and benzyltrimethylammonium (BTMA) and (ii) heating synthesized complexes in air at different temperatures (between 150 and 420°C). The aim of this work was to examine recently observed enhancement of aqueous sorption of a probe organic sorbate on organoclays after mild thermal pre-treatment of sorbents. Thermal pre-treatment of TEA- and BTMA-clays at 150°C results in the maximal enhancement of nitrobenzene–sorbent interactions as compared with treatment of original bentonite and its exchange complexes formed with long-chain quaternary ammonium (n-hexadecyltrimethylammonium, HDTMA). Based on C, N content data and FTIR spectra of TEA- and BTMA-clay complexes, no indications of decomposition of organic matter were found in organoclays heated at 250°C (and below this temperature). Suppressed hydration of pre-heated sorbents resulting in a lessening of water–organic sorbate competition for sorption sites is considered to be responsible for thermally induced enhancement of nitrobenzene–sorbent interactions. In the HDTMA-based organoclays, the long-chain aliphatic groups of the quaternary ammonium can additionally interact with clay surface thus competing with organic sorbate–sorbent surface interactions and, in this way, mitigating the enhancement of nitrobenzene sorption on thermally treated sorbents.     

Thermal degradation of poly(lactic acid) measured by thermogravimetry coupled to Fourier transform infrared spectroscopy

Thermogravimetric (TG), differential thermal analysis (DTA) and thermal degradation kinetics, FTIR and X-ray diffraction (XRD) analysis of synthesized glycine–montmorillonite (Gly–MMT) and montmorillonite bound dipeptide (Gly–Gly–MMT) along with pure Na–MMT samples have been performed. TG analysis at the temperature range 25–250 °C showed a mass loss for pure Na–MMT, Gly–MMT and Gly–Gly–MMT of about 8.0%, 4.0% and 2.0%, respectively. DTA curves show the endothermic reaction at 136, 211 and 678 °C in pure Na–MMT whereas Gly–MMT shows the exothermic reaction at 322 and 404 °C and that of Gly–Gly–MMT at 371 °C. The activation energies of the first order thermal degradation reaction were found to be 1.64 and 9.78 kJ mol⁻¹ for Gly–MMT and Gly–Gly–MMT, respectively. FTIR analyses indicate that the intercalated compounds decomposed at the temperature more than 250 °C in Gly–MMT and at 250 °C in Gly–Gly–MMT.     

Preparation and characterization of nanocomposite ZnO–Ag thin film containing nano-sized Ag particles: influence of preheating,annealing temperature and silver content on characteristics

Nanocomposite ZnO–Ag thin film containing nano-sized Ag particles have been grown on glass substrate by spin-coating technique using zinc acetate dihydrate as starting precursor in 2-propanol as solvent and monoethanolamine as stabilizer. Silver nanoparticles were added in the ZnO sol using silver nitrate dissolved in ethanol-acetonitrile. Their structural, electrical, crystalline size and optical properties were investigated as a function of preheating, annealing temperature and silver content. The results indicated that the crystalline phase was increased with increase of annealing temperature up to 550 °C at optimum preheating temperature of 275 °C. Thermal gravimetric differential thermal analysis results indicated that the decomposition of pure ZnO and nanocomposite ZnO–Ag precursors occurred at 225 and 234 °C, respectively with formation of ZnO wurtzite crystals. The scanning electron microscopy and atomic force microscopy revealed that the surface structure (the porosity and grain size) of the ZnO–Ag thin film (the film thickness is about 379 nm) was changed compared to pure ZnO thin film. The result of transmission electron microscopy showed that Ag particles were about 5 nm and ZnO particles 58 nm with uniform silver nanoclusters. Optical absorption results indicated that optical absorption of ZnO–Ag thin films decreased with increase of annealing temperature. Nanocomposite ZnO–Ag thin films with [Ag] = 0.068 M and [Ag] = 0.110 M showed an intense absorption band, whose maximum signals appear at 430 nm which is not present in pure ZnO thin films. The result of X-ray photoelectron spectroscopy revealed that the binding energy of Ag 3d_5/2 for ZnO–Ag shifts remarkably to the lower binding energy compared to the pure metallic Ag due to the interaction between Ag and ZnO.     

Pyrolysis of polystyrene in coal tar and ethylene tar pitches

Pyrolysis of polystyrene in the medium of coal tar pitch and of pitch prepared from ethylene production tar was performed in the temperature range 360–420°C at atmospheric pressure.     

Synthesis and optical property of NaTaO<Subscript>3</Subscript> nanofibers prepared by electrospinning

This paper describes a procedure of preparing sodium tantalite nanofibers for the first time. Sodium tantalite nanofibers were synthesised by electrospinning a sol–gel precursor solution of poly(vinyl pyrrolidone)/sodium tantalite, followed by careful sintering of the as-electrospun composite fibers at 550 °C for 3 h. The morphology, microstructure and crystal phase were investigated by transmission electron microcopy and X-ray diffraction. The optical property was characterized by ultraviolet–visible (UV–vis) spectrometer. Typical nanofibers were with diameter between 70 and 90 nm and length exceeding 0.1 mm. An unusual phenomenon, the red-shift of optical absorption band edge happened, indicated the fabricated NaTaO₃ nanofibers were potential good candidates for photocatalytic application. The experiment photodegradation of methylene blue by NaTaO₃ nanofibers under UV light irradiation was performed.     

Thermal study on electrospun polyvinylpyrrolidone/ammonium metatungstate nanofibers: optimising the annealing conditions for obtaining WO<Subscript>3</Subscript> nanofibers

This article demonstrates how important it is to find the optimal heating conditions when electrospun organic/inorganic composite fibers are annealed to get ceramic nanofibers in appropriate quality (crystal structure, composition, and morphology) and to avoid their disintegration. Polyvinylpyrrolidone [PVP, (C₆H₉NO) _n ] and ammonium metatungstate [AMT, (NH₄)₆[H₂W₁₂O₄₀]·nH₂O] nanofibers were prepared by electrospinning aqueous solutions of PVP and AMT. The as-spun fibers and their annealing were characterized by TG/DTA-MS, XRD, SEM, Raman, and FTIR measurements. The 400–600 nm thick and tens of micrometer long PVP/AMT fibers decomposed thermally in air in four steps, and pure monoclinic WO₃ nanofibers formed between 500 and 600 °C. When a too high heating rate and heating temperature (10 °C min⁻¹, 600 °C) were used, the WO₃ nanofibers completely disintegrated. At lower heating rate but too high temperature (1 °C min⁻¹, 600 °C), the fibers broke into rods. If the heating rate was adequate, but the annealing temperature was too low (1 °C min⁻¹, 500 °C), the nanofiber morphology was excellent, but the sample was less crystalline. When the optimal heating rate and temperature (1 °C min⁻¹, 550 °C) were applied, WO₃ nanofibers with excellent morphology (250 nm thick and tens of micrometer long nanofibers, which consisted of 20–80 nm particles) and crystallinity (monoclinic WO₃) were obtained. The FTIR and Raman measurements confirmed that with these heating parameters the organic matter was effectively removed from the nanofibers and monoclinic WO₃ was present in a highly crystalline and ordered form.     

Novel conductive characteristics of ITO:Ti films deposited by spin coating from colloidal precursor

Transparent semiconducting ITO:Ti thin films, prepared by a sol–gel process, has been deposited by spin-coating technique onto alkali-free glass substrates. The as-coated films were annealed in ambient air at 550 °C for 1 h and further annealed in a reducing atmosphere. The influences of the Ti content in the sol on the surface morphology, microstructure, optical properties and electrical resistivity have been investigated. These properties were found to depend on the Ti content in the coating sol. Ti addition led to dense smooth layers with larger crystallite size (20–30 nm). Double layers synthesized with Ti:ITO = 0.53 wt% and submitted to reducing treatment in forming gas exhibited the lowest sheet resistance R_□ = 60 Ω_□ with an average transmittance of 87% at 550 nm.     

Dried–Reswollen Immobilized Biocatalysts for Detoxification of Organophosphorous Compounds in the Flow Systems

New immobilized biocatalysts based on polypeptides containing N- or C-terminal polyhistidine sequences and possessing organophosphorus hydrolase activity were investigated for detoxification of organophosphorous neurotoxic compounds in the flow systems. The biocatalysts were revealed to have a high catalytic activity within wide pH and temperature ranges 7.5–12.5 °C and 15–65 °C, respectively. The immobilized biocatalysts can be dried and reswollen before use with 92–93% catalytic activity remaining after drying and rehydration procedures. The half-lives of the biocatalysts under wet and dry storage conditions were 420 and 540 days, respectively.     

Thermal behaviour of cephalexin in different mixtures

The thermoanalytical curves (TA), i.e. TG, DTG and DTA for pure cephalexin and its mixtures with talc, magnesium stearate, starch and microcrystalline cellulose, respectively, were drawn up in air and nitrogen at a heating rate of 10 °C min⁻¹. The thermal degradation was discussed on the basis of EGA data obtained for a heating rate of 20 °C min⁻¹. Until 250 °C, the TA curves are similar for all mixtures, up this some peculiarities depending on the additive appears. These certify that between the pure cephalosporin and the excipients do not exists any interaction until 250 °C. A kinetic analysis was performed using the TG/DTG data in air for the first step of cephalexin decomposition at four heating rates: 5, 7, 10 and 12 °C min⁻¹. The data processing strategy was based on a differential method (Friedman), an integral method (Flynn–Wall–Ozawa) and a nonparametric kinetic method (NPK). This last one allowed an intrinsic separation of the temperature, respective conversion dependence on the reaction rate and less speculative discussions on the kinetic model. All there methods had furnished very near values of the activation energy, this being an argument for a single thermooxidative degradation at the beginning (192–200 °C).     

Thermal characteristics of bitumen pyrolysis

The pyrolysis behavior of bitumen was investigated using a thermogravimetric analyzer–mass spectrometer system (TG–MS) and a differential scanning calorimeter (DSC) as well as a pyrolysis-gas chromatograph/mass spectrometer system (Py-GC/MS). TG results showed that there were three stages of weight loss during pyrolysis—less than 110, 110–380, and 380–600 °C. Using distributed activation energy model, the average activation energy of the thermal decomposition of bitumen was calculated at 79 kJ mol⁻¹. The evolved gas from the pyrolysis showed that organic species, such as alkane and alkene fragments had a peak maximum temperature of 130 and 480 °C, respectively. Benzene, toluene, and styrene released at 100 and 420 °C. Most of the inorganic compounds, such as H₂, H₂S, COS, and SO₂, released at about 380 °C while the CO₂ had the maximum temperature peaks at 400 and 540 °C, respectively. FTIR spectra were taken of the residues of the different stages, and the results showed that the C–H bond intensity decreased dramatically at 380 °C. Py-GC/MS confirmed the composition of the evolved gas. The DSC revealed the endothermic nature of the bitumen pyrolysis.     

Nano-sized polycrystalline bismuth silicon oxide powder by sol–gel technique

Bismuth silicon oxide (Bi₁₂SiO₂₀, BSO) nano crystalline powder was prepared by sol–gel technique using bismuth nitrate and tetraethyl orthosilicate as starting materials. The prepared samples were sintered at various temperatures (750 °C maximum) and characteristic sillenite single cubic phase with crystallite size ~38 nm (calculated from room temperature powder XRD measurements) was realized at 750 °C sintering temperature. SEM analysis showed that the powder contains the nano-sized particles with almost spherical morphology. The observed frequencies in room temperature FTIR spectrum could be assigned to Bi–O, Si–O and Bi–O–Si bonds. The FWHM (full width at half maximum) of the diffraction peaks decreased while the intensity of FTIR absorption lines increased with the increase in the sintering temperature indicating better bond formation and crystallization. The thermograph of the samples recorded in the temperature range 50–1,000 °C showed almost no weight loss after ~575 °C further confirmed the conclusion arrived at from XRD and FTIR analysis. The samples sintered at 750 °C showed about 50% absorbance in 400–600 nm region which was consistent with the pale yellow color of the sample. Broad blue emission centered ~478 nm was observed when excited by 350 nm radiation from a Xe-lamp. The intensity of this broad emission band increased while its FWHM decreased with the increase in sintering temperature. Self-trapped excitons could be responsible for this emission.     

Correlation between structural and optical properties of TiO<Subscript>2</Subscript>:ZnO thin films prepared by sol–gel method

We have studied structural and optical properties of thin films of TiO₂, doped with 5% ZnO and deposited on glass substrate (by the sol–gel method). Dip-coated thin films have been examined at different annealing temperatures (350–450 °C) and for various layer thicknesses (89–289 nm). Refractive index, porosity and energy band gap were calculated from the measured transmittance spectrum. The values of the index of refraction are in the range of 1.97–2.44, the porosity is in the range of 0.07–0.46 and the energy band gap is in the range of 3.32–3.43. The coefficient of transmission varies from 50 to 90%. In the case of the powder of TiO₂, doped with 5% ZnO, and aged for 3 months in ambient temperature, we have noticed the formation of the anatase phase (tetragonal structure with 20.23 nm grains). However, the undoped TiO₂ exhibits an amorphous phase. After heat treatments of thin films, titanium oxide starts to crystallize at the annealing temperature 350 °C. The obtained structures are anatase and brookite. The calculated grain size, depending on the annealing temperature and the layer thickness, is in the range of 8.61–29.48 nm.     

A simple route to obtain TiO2 nanowires by the sol–gel method

In this work, titanium dioxide (TiO₂) nanowires were synthesized by the sol–gel method, without using any kind of templates, instead of that acetic acid was used as morphological modifier. In order to control crystalline phases and crystal size, TiO₂ was calcinated at 400, 500 and 600 °C during 1 h. The resulting morphology was nanowires, which diameter was maintained constant after calcination at different temperature (about 76 nm). Moreover, crystalline phases in order of predominance were anatase, anatase–rutile and rutile–anatase at 400, 500 and 600 °C, respectively. Additionally, the crystallite size increases with respect to temperature from 13 to 75 nm.