Comparison of DNA Hybridization at Rotating and Heated Gold Disk Electrodes

This paper reports about the influence of temperature, hybridization time and convection upon the detection of osmium tetroxide bipyridine‐labeled target oligonucleotides at rotating gold disk (RDE) and heated low temperature co‐fired ceramics (LTCC) gold disk electrodes. We used mixed self‐assembled monolayers of hexathiol‐linked probe oligonucleotides and mercaptohexanol on the gold surface of the electrodes for the hybridization detection of the labeled targets by means of square‐wave voltammetry. Due to protective strands, the osmium tetroxide‐modified target strands were still able to hybridize with the immobilized probe strands. The hybridization of such osmium tetroxide bipyridine‐modified target strands with thiol‐linked probe strands immobilized on gold yielded large reversible square‐wave‐voltammetric signals. Rotation speed and, hence, mass transport due to convection has only marginal effects. On the other hand, temperature affects greatly the hybridization step as indicated by both heated LTCC electrode in cold and RDE in warm hybridization solution. Calculated detection limits of 3.6 and 3.1 nM targets at the RDE and the LTCC electrode, respectively, have been almost the same at both types of electrodes. Applying an appropriate temperature during hybridization is more important than mechanically enhanced mass transport.     

Detection of DNA immobilized on bare gold electrodes and gold nanoparticle-modified electrodes via electrogenerated chemiluminescence using a ruthenium complex as a tag

Electrogenerated chemiluminescence (ECL) for DNA hybridization detection is demonstrated based on DNA that was self-assembled onto a bare gold electrode and onto a gold nanoparticles modified gold electrode. A ruthenium complex served as an ECL tag. Gold nanoparticles were self-assembled on a gold electrode associated with a 1,6-hexanedithiol monolayer. The surface density of single stranded DNA (ssDNA) on the gold nanoparticle modified gold electrode was 4.8?×?10¹⁴ molecules per square centimeter which was 12-fold higher than that on the bare gold electrode. Hybridization was induced by exposure of the target ssDNA gold electrode to the solution of ECL probe consisting of complementary ssDNA tagged with ruthenium complex. The detection limit of target ssDNA on a gold nanoparticle modified gold electrode (6.7?×?10^?12 mol L^?1) is much lower than that on a bare gold electrode (1.2?×?10^?10 mol L^?1). The method has been applied to the detection of the DNA sequence related to cystic fibrosis. This work demonstrates that employment of gold nanoparticles self-assembled on a gold electrode is a promising strategy for the enhancement of the sensitivity of ECL detection of DNA.     

A Sensitive Nanoporous Gold-Based Electrochemical DNA Biosensor for Escherichia coli Detection

A sensitive electrochemical DNA biosensor based on a mixed monolayer structure self-assembled at nanoporous gold (NPG) electrode surface was prepared for Escherichia coli (E. coli) detection. The NPG was fabricated on gold electrode, onto which thiolated oligonucleotides (SH-DNA) and mercaptohexanol (MCH) were covalently linked forming a mixed self-assembled monolayer (SAM). The hybridization between the SH-DNA/MCH modified biosensor and E. coli DNA was monitored with differential pulse voltammetry measurement using methylene blue (MB) as the hybridization indicator. The biosensor can detect 1 × 10^?12 M DNA target and 50 cfu/μL E. coli without any nucleic acid amplification steps. The detection limit was lowered to 50 cfu/mL after 5.0 h of incubation.     

DNA Hydrolysis and Voltammetric Determination of Guanine and Adenine Using Different Electrodes

Abstract

This work reports the development of a biosensor method for the label‐free detection of specific DNA sequences. In the initial phase, square wave voltammetry (SWV) was used in a comparative investigation into the electrochemical oxidation of purines (guanine and adenine) and DNA fragments at various electrode surfaces: carbon paste (CPE), glassy carbon electrode (GCE), and gold (AuE). Relative to the carbon electrodes, an approximate 4.0‐fold, 6.0‐fold, and 3.25‐fold increase in the anodic response was observed when guanine, adenine, and hydrolyzed DNA, respectively, were measured on the AuE. It was shown that the guanine and adenine bases could be successfully determined by use of SWV for a deoxyribonucleic acid sample following acid hydrolysis. This label‐free detection of hydrolyzed DNA on gold electrodes has significant advantages over methods using existing carbon electrode materials because of its higher sensitivity and the potential applicability of microfabrication techniques for the production of the requisite gold electrodes.

In another phase of development, the times and conditions for DNA hydrolysis and purine release were investigated. It was shown that under optimal conditions, trace levels of the purine bases could be readily detected following 20 min of hydrolysis at room temperature. The proposed method can be used to estimate the guanine and adenine contents in DNA with in a linear range of 5–30 ng ml^?1.

Finally, when appropriate probe sequences were first adsorbed on the surface of the screen‐printed gold electrode (SPGE), this electrochemical biosensor could be used to specifically detect sequences from ss corona virus aviair following hybridization and hydrolysis reactions on the sensor surface. No enhancement of the voltammetric response was observed when the sensor was challenged with a non‐complementary DNA sequence.     

ToF-secondary ion mass-spectrometric study of copper deposition and stripping on directly heated screen-printed gold electrodes

We report about a new kind of directly heated gold electrode. All electrodes including a directly heated gold loop electrode, a Ag pseudo reference, and a carbon counter electrode have been screen-printed on a ceramic alumina substrate. Thermal behaviour was studied by potentiometry using either an external or the integrated reference electrode. Stripping voltammetric copper signals were greatly improved at elevated deposition temperature. Secondary ion mass spectrometric studies (ToF-SIMS) revealed that different negative ionic species of copper complexes can be found on the gold electrode surface as a result of ion bombardment during SIMS analysis like Cu^?, CuCl^? and CuCl₂ ^?. SIMS surface imaging using a fine focussed ion beam over the surface allowed us to obtain ion images (chemical maps) of the analyzed sample. SIMS depth profile analysis of the gold loop electrode was performed after copper deposition at room temperature (23 °C) and at 60 °C. CuCl₂ ^? ion was used for the depth profile studies as it has shown the highest intensity among other observed species. Surface spectroscopic analysis, surface imaging and depth profile analysis have shown that the amount of deposited copper species on the gold loop electrode was increased upon increasing electrode temperature during the deposition step. Therefore, the presence of chloride in the solution will hinder underpotential deposition of Cu(0) and lead to badly defined and resolved stripping peaks.     

Sensitive detection of enteropathogenic E. coli using a bfpA gene-based electrochemical sensor

We have developed a sensitive assay for enteropathogenic E. coli (EPEC) by integrating DNA extraction, specific polymerase chain reaction (PCR) and DNA detection using an electrode modified with the bundle-forming pilus (bfpA) structural gene. The PCR amplified products are captured on the electrode and hybridized with biotinylated detection probes to form a sandwich hybrid containing two biotinylated detection probes. The sandwich hybridization structure significantly combined the numerous streptavidin alkaline phosphatase on the electrode by biotin-streptavidin connectors. Electrochemical readout is based on dual signal amplification by both the sandwich hybridization structure and the enzyme. The electrode can satisfactorily discriminate complementary and mismatched oligonucleotides. Under optimal conditions, synthetic target DNA can be detected in the 1 pM to 10 nM concentration range, with a detection limit of 0.3 pM. EPEC can be quantified in the 10 to 10⁷ CFU mL^?1 levels within 3.5 h. The method also is believed to present a powerful platform for the screening of pathogenic microorganisms in clinical diagnostics, food safety and environmental monitoring.

Electrochemical Detection of DNA Melting Curves by Means of Heated Biosensors

This article reports about the detection of DNA melting curves at heated electrochemical biosensors. Osmium tetroxide‐bipyridine‐labeled target oligonucleotides are hybridized with probe oligonucleotides immobilized on gold electrodes. Then, the gold electrode is successively heated in order to measure a complete melting curve consisting of alternating current voltammetric signals. Melting temperatures ?_m, determined at various ionic strengths and in dependence on different numbers of base pair mismatches, have been compared with those obtained by means of UV spectrophotometry. The proposed method holds great promise for the fast and easy parallel detection of nucleic acids sequences on selectively heated electrode arrays. A stringent hybridization temperature can be easily adjusted in order to discriminate base pair mismatches.     

Nano-ZnO/Chitosan Composite Film Modified Electrode for Voltammetric Detection of DNA Hybridization

Abstract

A sensitive electrochemical DNA biosensor based on nano-ZnO/chitosan composite matrix for DNA hybridization detection was developed. The Nano-ZnO was synthesized by the hydrothermal method and dispersed in chitosan, which was used to fabricate the modification of the glassy carbon electrode (GCE) surface. The ZnO/chitosan-modified electrode exhibited good biocompatibility and excellent electrochemical conductivity. The hybridization detection was monitored with differential pulse voltammetry (DPV) measurement using methylene blue (MB) as an indicator. The established biosensor can effectively discriminate complementary target sequence and two-base-mismatched sequence, with a detection limit of 1.09 × 10^?11 mol L^?1 of complementary target.     

DNA hybridization detection at heated electrodes

The detection of DNA hybridization is of central importance to the diagnosis and treatment of genetic diseases. Due to cost limitations, small and easy-to-handle testing devices are required. Electrochemical detection is a promising alternative to evaluation of chip data with optical readout. Independent of the actual readout principle, the hybridization process still takes a lot of time, hampering daily use of these techniques, especially in hospitals or doctor's surgery. Here we describe how direct local electrical heating of a DNA-probe-modified gold electrode affects the surface hybridization process dramatically. We obtained a 140-fold increase of alternating current voltammetric signals for 20-base ferrocene-labeled target strands when elevating the electrode temperature during hybridization from 3 to 48 degrees C while leaving the bulk electrolyte at 3 degrees C. At optimum conditions, a target concentration of 500 pmol/L could be detected. Electrothermal regeneration of the immobilized DNA-probe strands allowed repetitive use of the same probe-modified electrode. The surface coverage of DNA probes, monitored by chronocoulometry of hexaammineruthenium(III), was almost constant upon heating to 70 degrees C. However, the hybridization ability of the probe self-assembled monolayer declined irreversibly when using a 70 degrees C hybridization temperature. Coupling of heated electrodes and highly sensitive electrochemical DNA hybridization detection methods should enhance detection limits of the latter significantly.     

A Sequence‐Selective Electrochemical DNA Biosensor Based on HRP‐Labeled Probe for Colorectal Cancer DNA Detection

Abstract

A highly‐sensitive sequence‐selective DNA sensor based on HRP‐labeled probe to detect specific K‐ras gene which is highly associated with colorectal cancer has been reported. Capture probe modified with–SH was first chemically adsorbed on the gold electrode through self‐assembly. Then, the hybridization of a complementary nucleic acid (target DNA:K‐ras gene) and HRP labeled oligonucleotide detection probe occurred in a sandwich way. Finally, H₂O₂ electroreduction current catalyzed by HRP was measured amperometrically in the presence of hydroquinon as mediator. The sequence selectivity is double guaranteed by the complementary hybridization of target DNA with capture and detection probes. The experimental conditions were optimized. The linear range is 1.17×10^?11～1.17×10^?7 mol l^?1 with a detection limit of 5.85×10^?12 mol l^?1. The electrode with capture probe can be reused after regeneration in boiling water.     

Ultra-sensitive electrochemical DNA biosensor based on signal amplification using gold nanoparticles modified with molybdenum disulfide,graphene and horseradish peroxidase

We have developed an ultra-sensitive electrochemical DNA biosensor by assembling probe ssDNA on a glassy carbon electrode modified with a composite made from molybdenum disulfide, graphene, chitosan and gold nanoparticles. A thiol-tagged DNA strand coupled to horseradish peroxidase conjugated to AuNP served as a tracer. The nanocomposite on the surface acts as relatively good electrical conductor for accelerating the electron transfer, while the enzyme tagged gold nanoparticles provide signal amplification. Hybridization with the target DNA was studied by measuring the electrochemical signal response of horseradish peroxidase using differential pulse voltammetry. The calibration plot is linear in the 5.0?×?10^?14 and 5.0?×?10^?9 M concentration range, and the limit of detection is 2.2?×?10^?15 M. The biosensor displays high selectivity and can differentiate between single-base mismatched and three-base mismatched sequences of DNA. The approach is deemed to provide a sensitive and reliable tool for highly specific detection of DNA.

Label-Free DNA Biosensor for Electrochemical Detection of Short DNA Sequences Related to Human Papilloma Virus

Abstract

Highly sensitive label-free techniques of DNA determination are particularly interesting in relation to the present development of an electrochemical hybridization biosensor for the detection of short DNA fragments specific to the human papilloma virus (HPV). Unlabeled DNA probes have been immobilized by spontaneous coadsorption of thiolated single-stranded oligonucleotides (HS-ssDNA) onto the sensing surface of a screen-printed gold electrode (SPGE). The covalently immobilized single-stranded DNA probe (HS-ssDNA) could selectively hybridize with its complementary DNA (cDNA) in solution to form double-stranded DNA (dsDNA) on the surface. DNA is treated with acid (e.g., 0.5 M chloridric acid), and the acid-released purine bases are directly determined by square wave voltammetry (SWV).

Variables of the probe-immobilization and hybridization steps are optimized to offer convenient quantitation of HPV DNA target, in connection with a short hybridization time. Peak currents were found to increase in the following order: hybrid-modified SPGE, 11-base mismatched modified SPGE, 18-base mismatched SPGE, and the probe modified SPGE. Control experiments with noncomplementary oligonucleotides were carried out to assess whether the suggested DNA sensor responds selectively to the target. The effect of the target DNA concentration on the hybridization signal was also studied. Under optimal conditions, this sensor has a good calibration range with HPV DNA sequence detection limit of 2 pg · ml^?1 (S/N = 3).     

Basics of temperature pulse voltammetry

A new electrochemical technique is presented that allows peak-shaped voltammograms to be recorded at local temperature values from room temperature to above boiling point. This new method, temperature pulse voltammetry (TPV), is analogous to differential pulse voltammetry (DPV), but makes use of temperature jumps instead of potential pulses. Fundamentals are presented and potentialities demonstrated. As an example, ferrocyanide is investigated using a new kind of heated electrode on the basis of screen-printed gold layer structures on low-temperature cofired ceramics (LTCC) substrates.     

Designs of Enterobacteriaceae Lac Z Gene DNA Gold Screen Printed Biosensors

This paper describes specific electrochemical enterobacteriaceae lac Z gene DNA sensors based on immobilization of a thiolated 25 base single stranded probe onto disposable screen printed gold electrodes (gold SPEs). Two configurations have been evaluated. In the first one, the capture probe was attached to the electrode surface through its ? SH moiety, while mercaptohexanol (MCH) was used as spacer for the displacement of nonspecifically adsorbed oligonucleotide molecules. The hybridization event between the probe and target DNA sequences was detected at ?0.20 V by square‐wave voltammetry (SWV), using methylene blue (MB) as electrochemical indicator. The second genosensor configuration involved modification of gold high temperature SPEs with a 3,3′‐dithiodipropionic acid di(N‐succinimidyl ester) (DTSP) self‐assembled monolayer (SAM). Moreover, 2‐aminoethanol was used as blocking agent, and further modification with avidin allowed binding of the biotinylated enterobacteriaceae lac Z gene DNA probe. An enzyme amplified detection scheme was applied, based on the coupling of streptavidin‐peroxidase to the biotinylated complementary target, after the hybridization process, and immobilization of tetrathiafulvalene (TTF) as redox mediator atop the modified electrode. The amperometric response obtained at ?0.15 V after the addition of hydrogen peroxide was used to detect the hybridization process. Experimental variables concerning sensors composition and electrochemical transduction were evaluated in both cases. A better precision and reproducibility in the fabrication process, as well as a higher sensitivity were achieved using the biotinylated probe‐based sensor configuration. A limit of detection of 0.002 ng/μL was obtained without any preconcentration step.     

Temperature pulse voltammetry: hot layer electrodes made by LTCC technology

A new electrochemical technique is presented that allows peak-shaped voltammograms to be recorded at local temperature values from room temperature to above boiling point. This new method, temperature pulse voltammetry (TPV), is analogous to differential pulse voltammetry (DPV), but makes use of temperature jumps instead of potential pulses. Fundamentals are presented and potentialities demonstrated. As an example, ferrocyanide is investigated using a new kind of heated electrode on the basis of screen-printed gold layer structures on low-temperature cofired ceramics (LTCC) substrates.     

Lable‐Free Electrochemical DNA Sensor Based on Gold Nanoparticles/Poly(neutral red) Modified Electrode

We present a new strategy for the label‐free electrochemical detection of DNA hybridization based on gold nanoparticles (AuNPs)/poly(neutral red) (PNR) modified electrode. Probe oligonucledotides with thiol groups at the 5‐end were covalently linked onto the surface of AuNPs/PNR modified electrode via S‐Au binding. The hybridization event was monitored by using differential pulse voltammetry (DPV) upon hybridization generates electrochemical changes at the PNR‐solution interface. A significant decrease in the peak current was observed upon hybridization of probe with complementary target ssDNA, whereas no obvious change was observed with noncomplementary target ssDNA. And the DNA sensor also showed a high selectivity for detecting one‐mismatched and three‐mismatched target ssDNA and a high sensitivity for detecting complementary target ssDNA, the detection limit is 4.2×10^?12 M for complementary target ssDNA. In addition, the DNA biosensor showed an excellent reproducibility and stability under the DNA‐hybridization conditions.     

Proximity-based electrochemical biosensor for highly sensitive determination of methyltransferase activity using gold nanoparticle-based cooperative signal amplification

We describe a turn-on electrochemical biosensor for the detection of methyltransferases (MTases) causing DNA adenine methylation. This biosensor is based on insertion, methylation-resistant cleavage, signal enrichment caused by gold nanoparticles (AuNPs), and a signal probe-dragging strategy. A double-stranded DNA (dsDNA) containing identical MTase and methylation-resistant endonuclease (Mbo I) sites was immobilized on the surface of a gold electrode via Au-S covalent binding. The surface was subsequently treated with MTase and Mbo I and then washed. Results revealed that the surface of the electrode contains methylated dsDNA and 12-base nucleotides residual. Depending on biotin-streptavidin interactions that enabled signal probes and nucleotide residue hybridization and AuNP enrichment, a large number of signal probes labeled with ferrocene (Fc) are captured by the electrode. Under optimal conditions, the differential pulse voltammetry signals of Fc tags (at a working voltage of 0.24 V vs. Ag/AgCl) are linearly related to the log of the MTase activity in the 0.1 to 40 U·mL⁻¹ range. The dynamic range extends from 0.05 to 50 U·mL⁻¹, and the limit of detection is 0.024 U·mL⁻¹ (at an S/N ratio of 3). The assay is well reproducible and highly selective. In our perception, this strategy provides a promising approach for simple, sensitive and selective detection of Dam MTase and may be extended to the determination of other MTase by exchanging the corresponding DNA.

Proximity-based electrochemical biosensor for highly sensitive detection of DNA adenine methylation methyltransferase (Dam MTase) activity using methylation-resistant cleavage coupled with gold nanoparticle based cooperative signal amplification.

     

Development of electrochemical genosensor for MYCN oncogene detection using rhodamine B as electroactive label

A novel electrochemical genosensor based on a graphite electrode modified with poly(4-aminophenol) has been constructed for prognostic of neuroblastoma, a malignant tumor originating from embryonic precursor cells of the sympathetic nervous system and associated with the amplification of the MYCN oncogene. The genosensor exhibited distinct electrical and morphological properties using rhodamine B as indicator of DNA hybridization. The detection limit was evaluated to be 0.47 μmol L^?1 (n = 3), and the electrochemical genosensor was selective for the complementary DNA, using serum sample. This DNA sensing platform was successfully applied to detect MYCN, an important biomarker for neuroblastoma.     

Hybridization Detection of Osmium Tetroxide Bipyridine‐Labeled DNA and RNA on Heated Gold Wire Electrodes

We report about hybridization detection of different nucleic acids on capture probe‐modified heated gold wire electrodes. We have compared three kinds of nucleic acid targets: DNA, uracil‐conjugated DNA, and RNA. All three sorts of nucleic acids targets could be labeled with osmium tetroxide bipyridine, hybridized with immobilized DNA capture probes and then detected by square‐wave voltammetry. Heating the gold electrode instead of the entire bulk hybridization solution leads to improved hybridization efficiency in most cases. The reason could be found in a thermal micro‐stirring effect around the heated wire electrode. Also selectivity was improved. Mismatches could be discriminated for DNA and uracil‐conjugated DNA targets. Mismatches in RNA strands, however, are more difficult to detect due to relatively stable secondary structures.     

Impedimetic biosensor for the DNA of the human papilloma virus based on the use of gold nanosheets

The authors describe an impedimetric method for the quantitation of the DNA of the human papilloma virus (HPV) type 16. A glassy carbon electrode (GCE) was modified with gold nanosheets and is shown to be superior to a common gold disk electrode. A single-stranded 25mer oligonucleotide (ssDNA) acting as the probe DNA was immobilized via its thiolated 5′ end on both electrodes. After hybridization with target (analyte) DNA, electrochemical impedance spectra were acquired in the presence of hexacyanoferrate as a redox marker. The sensor can distinguish between complementary, non-complementary and single base pair mismatches of HPV ssDNA. At a 1 mM hexacyanoferrate concentration, the biosensors respond to target DNA in the 1 μM to 1 pM concentration range, and the detection limit is 0.15 pM. The results illustrate that the use of gold nanosheets on a GCE distinctly improves the detection and differentiation of HPV compared to using bare gold.

Open image in new window

Graphical abstract Schematic of exploiting gold nanosheets as a platform for HPV detection. The method works in the 1 μM to 1 pM HPV concentration range and has a 0.15 pM detection limit..