Synthesis and evaluation of new propazine-imprinted polymer formats for use as stationary phases in liquid chromatography

Silica particles have been used as supports for the preparation of three different propazine-imprinted polymer formats. First format refers to grafting of thin films of molecularly imprinted polymers (MIPs) using an immobilised iniferter-type initiator (inif-MIP). The other two new formats were obtained by complete filling of the silica pores with the appropriate polymerisation mixture leading to a silica-MIP composite material (c-MIP) followed by the dissolution of the silica matrix resulting in spherical MIP beads (dis-MIP). These techniques offer a mean of fine-tuning the particle morphology of the resulting MIP particles leading to enhanced capacity in chromatographic applications. Porous silica (specific surface area S = 380 m² g⁻¹, particle size p_s = 10 μm, pore volume V_p = 1.083 ml g⁻¹ and pore diameter d_p = 10.5 nm), methacrylic acid and ethylenglycol dimethacrylate were used for the preparation of the materials. All the MIP formats imprinted with propazine have been characterised by elemental analysis, FT-IR spectroscopy, nitrogen adsorption and scanning electron microscopy. Further, the materials were assessed as stationary phases in HPLC. Capacity factors, imprinting factors and theoretical plate numbers were calculated for propazine and other related triazines in order to compare the chromatographic properties of the three different stationary phases. For the inif-MIPs the column efficiency depended strongly on the amount of grafted polymer. Thus, only the polymers grafted as thin films of ca. 1.3 nm average thickness show imprinting effects and the highest column efficiency giving plate numbers (N) of 1600 m⁻¹ for the imprinted propazine. The performance of the c-MIP stationary phase decreases as result of the complete pore filling after polymerisation and increases again after the removal of the silica matrix due to a better mass transfer in the porous mirror-image resulting polymer. From this study can be concluded that the inif-MIP shows the best efficiency for use as stationary phase in HPLC for the separation of triazinic herbicides.     

The absorption and thermal behaviors of PET-SiO2 nanocomposite films

In this paper, to improve properties of Poly(ethylene terephthalate) (PET) in thermal stability and barrier to water, the films of PET, PET with micronmeter Silica/Polystyrene (SiO₂/PS) composites (SPET) and PET with nano-SiO₂/PS composites (SNPET) are prepared and their water absorption and thermal stable behaviors are investigated.In the samples, silica load is optimized as 2 wt%, at which silica not only disperses well but also forms the tough morphology in PET as investigated by SEM. The nanoeffect and thermal degradation behaviors of SNPET are firstly presented.The water absorption experiments for the samples show that the maximum absorption water weight percentage (C_∞) and the pseudo-diffusion coefficient (D) of water reduce with SiO₂ particle size varying from 440 nm to 40 nm, and the barrier property to water of SNPET is superior to those of pure PET and SPET. At the minimum silica size of 40 nm, the C_∞ and D of SNPET approach the minimum values that are 0.946% and 7.075 × 10⁻¹³ m² s⁻¹, respectively. Fixing SiO₂ size at 40 nm, with un-modified SiO₂ and modified SiO₂, the core-shell SiO₂/PS nanocomposite particles are more effective on keeping PET from absorbing water. With the increase in nano-SiO₂ load, the C_∞ and D of SNPET films reduce, proving that the nano-SiO₂ particles can inhibit water absorption. When amorphous SNPET films are annealed at 130 °C, their C_∞ and D quickly decrease with the increase in annealing time, stating that the crystallized SNPET also retards the water absorption or diffusion in PET. Under oversaturated oxygen atmosphere, the C_∞ and D of amorphous PET and SNPET, and crystallized SNPET samples are higher than those of corresponding samples without flowing oxygen, showing that oxygen promotes the films to absorb water.TGA results show that SNPET keeps similar thermal degradation behavior under the conditions of with and without both water and oxygen. But SNPET is more thermally stable than PET.     

A new resonance scattering spectral method for the determination of trace amounts of iodate with rhodamine 6G

Under the conditions of 0.04 mol L⁻¹ HCl-8.0 × 10⁻⁴ mol L⁻¹ KI, there is a fluorescence peak at 540 nm and a synchronous fluorescence peak at 540 nm for rhodamine 6G (RhG). When there is IO₃⁻, it reacts with exceed I⁻ to form I₃⁻. And I₃⁻ and RhG combine into ion association particles. The particles exhibit three resonance scattering peaks at 320, 400 and 595 nm. And there is fluorescence quenching at 540 nm. Iodine concentration is proportional to the intensity of the resonance scattering intensity at 400 nm in the range of 1.0-20 × 10⁻⁷ mol L⁻¹. And a new resonance scattering spectral (RSS) method has been described for the determination of IO₃⁻ in salt samples. The spectral results have been verified that the formation of (RhG-I₃)_n association particles and solid-liquid interfaces are the main factor that cause the fluorescence quenching and resonance scattering effects.     

Determination of citrate in tablets and of oxytetracycline in serum using europium (III) luminescence

A direct method for the determination of citrate and oxytetracycline in samples containing complex matrices like tablets or serum has been developed using the luminescence of the ternary complex formed with Eu(III) ions. The triplet-state energy level of oxytetracycline (OxTc), the excitation maximum (412 nm) and the luminescence lifetime of Eu-OxTc (58 μs) were determined. A 17-fold luminescence enhancement at 615 nm occurs upon addition of citrate within a short 5-min incubation time at neutral pH. This is accompanied by a threefold increase of the luminescence decay time. The optimal conditions for determination of OxTc are equal concentrations of Eu (III) and citrate (C = 1 · 10^− 4 mol L^− 1) and pH 7.2. For determination of citrate, the optimal concentrations of Eu(III) and OxTc are 1 : 0.5 (C_Eu = 1 · 10^− 4 mol L^− 1, C_OxTc = 5 · 10^− 5 mol L^− 1) at pH 7.2. The linear range for determination of OxTc in serum is 0.25-250 μg mL^− 1, and for citrate in tablets from 0.5 to 10.0 μg mL^− 1 (2.3 · 10^− 6- 4 · 10^− 5 mol L^− 1). The detection limit was 0.1 μg mL^− 1 for OxTc and 0.2 μg mL^− 1 (1 · 10^-6 mol L^− 1) for citrate, respectively. A comparison of the new method with other methods for determination of citrate is given.     

Multicommutated flow system for the determination of glucose in honey with immobilized glucose oxidase reactor and spectrophotometric detection

A new automated method for the determination of glucose in honey is proposed. The method is based on multicommutated flow analysis (MCFA) and employs an immobilized glucose oxidase reactor and spectrophotometric detection at 505 nm of the red quinoneimine formed (Trinder's method).The calibration curve obeyed a second order equation in the range 0-0.14 g L⁻¹ (h = −2.2199 C² + 1.3741C + 0.0077, r² = 0.9991, where h is the peak height (absorbance) and C the concentration in g L⁻¹). The method was validated analyzing eight commercial samples, both by the AOAC 954.11 and 977.20 official methods. According to Student's t-test of mean values, at the confidence level of 95% the results obtained with the proposed method were in agreement with those obtained by the official methods. Precision (s_r(%), n = 10) was 3% and the sampling frequency of the system was 20 samples h⁻¹.     

Development of cloud point extraction using pH-sensitive hydrogel for preconcentration and determination of malachite green

A novel and sensitive cloud point extraction procedure using pH-sensitive hydrogel was developed for preconcentration and spectrophotometric determination of trace amounts of malachite green (MG). In this extraction method, appropriate amounts of poly(styrene-alt-maleic acid), as a pH-sensitive hydrogel, and HCl were added respectively into the aqueous sample so a cloudy solution was formed. The cloudy phase consists of hydrogel particles distributed entirely into the aqueous phase. Organic or inorganic compounds having the potential to interact with polymer particles (chemical interaction or physical adsorption) could be extracted to cloudy phase. After centrifuging, these particles of hydrogel were sedimented in the bottom of sample tube. The sedimented hydrogel-rich phase was diluted with acetonitrile and its absorbance was measured at 617 nm (λ_max of malachite green in hydrogel). Central composite design and response surface method were applied to design the experiments and optimize the experimental parameters such as, concentration of hydrogel and HCl, extraction time and salting out effect. Under the optimum conditions, the linear range was 1 × 10⁻⁸-5 × 10⁻⁷ mol L⁻¹ malachite green with a correlation coefficient of 0.992. The limit of detection (S/N = 3) was 4.1 × 10⁻⁹ mol L⁻¹. Relative standard deviation (RSD) for 7 replicate determinations of 10⁻⁷ mol L⁻¹ malachite green was 3.03%. In this work, the concentration factor of 20 was reached. Also the improvement factor of the proposed method was 23. The advantages of this method are simplicity of operation, rapidity and low cost.     

Development of polyoxadiazole nanocomposites for high temperature polymer electrolyte membrane fuel cells

Novel nanocomposite membranes were prepared with sulfonated polyoxadiazole and different amounts of sulfonated dense and mesoporous (MCM-41) silica particles. It has been shown that particle size and functionality of sulfonated silica particles play an important role when they are used as fillers for the development of polymer electrolyte nanocomposite membrane for fuel cells. No significant particle agglomerates were observed in all nanocomposite membranes prepared with sulfonated dense silica particles, as analyzed by SEM, AFM, TGA, DMTA and tensile tests. The T_g values of the composite membranes increased with addition of sulfonated silica, indicating an interaction between the sulfonic acid groups of the silica and the polyoxadiazole. Constrained polymer chains in the vicinity of the inorganic particles were confirmed by the reduction of the relative peak height of tan δ. A proton conductivity of 0.034 S cm⁻¹ at 120 °C and 25% RH, which is around two-fold higher than the value of the pristine polymer membrane was obtained.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

Adsorptive stripping voltammetry of nickel with 1-nitroso-2-napthol using a bismuth film electrode

A sensitive procedure is presented for the voltammetric determination of nickel. The procedure involves an adsorptive accumulation of nickel 1-nitroso-2-napthol (NN) complex on a bismuth film electrode prepared ex situ by electrodeposition. The most suitable operating conditions and parameters such as pH, ligand concentration (C_NN), adsorptive potential (E_ads), adsorptive time (t_ads), scan rate and others were selected and the determination of nickel in aqueous solutions using the standard addition method was possible. The adsorbed Ni-NN complex gives a well defined cathodic stripping peak current at −0.70 V, which was used for the determination of nickel in the concentration range of 10.0-70.0 μg L⁻¹ (pH 7.5; C_NN 6.5 μmol L⁻¹; E_ads −0.30 V; t_ads 60 s) with a detection limit of 0.1 μg L⁻¹. The relative standard deviation for a solution containing 10.0 μg L⁻¹ of Ni(II) was 3.5% (n = 4). The proposed method was validated determining Ni(II) in certified reference waste water (SPS-WW1) and Certified Reference Water for Trace Elements (TMDA 51.3) with satisfactory results. Then lake water samples were analyzed.     

Determination of lead in the presence of morin-5′-sulfonic acid and sodium dodecyl sulfate by adsorptive stripping voltammetry

A simple and sensitive electroanalytical method is developed for the determination of lead by adsorptive stripping voltammetry (AdSV) in the presence of morin-5′-sulfonic acid (MSA) and sodium dodecyl sulfate (SDS). The Pb-MSA complex accumulates on the surface of a hanging mercury drop electrode (HMDE) and peak current is measured by square wave voltammetry (SWV). The complex is reduced at −0.48 V and peak current increases when low concentrations of SDS are added to the sample solution. The experimental variables pH, MSA concentration (C_MSA); accumulation time (t_acc); accumulation potential (E_acc), and SDS concentration (C_SDS), as well as potential interferences, are investigated. Under the optimized conditions (pH 3.2; C_MSA: 0.5 μmol L⁻¹; t_acc: 60 s; E_acc: −0.35 V, and C_SDS: 20 μmol L⁻¹), peak current is proportional to the concentration of Pb(II) over the 0.1-32.0 μg L⁻¹ range, with a detection limit of 0.04 μg L⁻¹. The relative standard deviation for a solution containing 5.0 μg L⁻¹ of Pb(II) solution was 1.5% for seven successive assays. The method was validated by determining Pb(II) in synthetic sea water (ASTM D665) spiked with ICP multi-element standard solution and in certified reference water (GBW08607). Finally, the method was successfully applied to the determination of Pb(II) in tap water and sea water after UV digestion.     

Determination of hydrogen sulfide and volatile thiols in air samples by mercury probe derivatization coupled with liquid chromatography-atomic fluorescence spectrometry

A new procedure is proposed for the sampling and storage of hydrogen sulphide (H₂S) and volatile thiols (methanethiol or methyl mercaptan, ethanethiol and propanethiol) for their determination by liquid chromatography. The sampling procedure is based on the trapping/pre-concentration of the analytes in alkaline aqueous solution containing an organic mercurial probe p-hydroxymercurybenzoate, HO-Hg-C₆H₄-COO⁻ (PHMB), where they are derivatized to stable PHMB complexes based on mercury-sulfur covalent bonds. PHMB complexes are separated on a C₁₈ reverse phase column, allowing their determination by liquid chromatography coupled with sequential non-selective UV-vis (DAD) and mercury specific (chemical vapor generation atomic fluorescence spectrometry, CVGAFS) on-line detectors. PHMB complexes, S(PHMB)₂CH₃S-PHMB, C₂H₅S-PHMB and C₃H₇S-PHMB, are stable alt least for 12 h at room temperature and for 3 months if stored frozen (−20 °C).The best analytical figures of merits in the optimized conditions were obtained by CVGAFS detection, with detection limits (LODc) of 9.7 μg L⁻¹ for H₂S, 13.7 μg L⁻¹ for CH₃SH, 17.7 μg L⁻¹ for C₂H₅SH and 21.7 μg L⁻¹ for C₃H₇SH in the trapping solution in form of RS-PHMB complexes, the relative standard deviation (R.S.D.) ranging between 1.0 and 1.5%, and a linear dynamic range (LDR) between 10 and 9700 μg L⁻¹. Conventional UV absorbance detectors tuned at 254 nm can be employed as well with comparable R.S.D. and LDR, but with LODc one order of magnitude higher than AFS detector and lower specificity. The sampling procedure followed by LC-DAD-CVGAFS analysis has been validated, as example, for H₂S determination by a certified gas permeation tube as a source of 3.071 ± 0.154 μg min⁻¹ of H₂S, giving a recovery of 99.8 ± 7% and it has been applied to the determination of sulfur compounds in real gas samples (biogas and the air of a plant for fractional distillation of crude oil).     

Determination of aluminium in water samples by adsorptive cathodic stripping voltammetry in the presence of pyrogallol red and a quaternary ammonium salt

A fast, sensitive and selective method for the determination of aluminium based on the reaction of the metal with pyrogallol red (PR) in the presence of tetrabutylammonium tetrafluoroborate (TBATFB) to form an Al(PR)₃x9TBATFB complex which is adsorbed on the mercury electrode is presented. Under these conditions complexation of aluminium is rapid and no waiting period or heating of the sample is required. The reduction current of the accumulated complex is measured by scanning the potential in the cathodic direction. The variation of peak current with pH, adsorption time, adsorption potential, ligand and quaternary ammonium salt concentration, and some instrumental parameters, such as stirring rate in the accumulation stage, and step amplitude, pulse amplitude and step duration while obtaining the square wave voltamperograms were optimized. The best experimental parameters were pH 8.5, (NH₄Ac-NH₃ buffer), C_PR = 25 μmol L⁻¹, C_TBATFB over 75 μmol L⁻¹, t_ads = 60 s, and E_ads = −0.60 V versus Ag/AgCl. A linear response is observed over the 0.0-30.0 μg L⁻¹ concentration range, with a detection limit of 1.0 μg L⁻¹. Reproducibility for 9.0 μg L⁻¹ aluminium solution was 2.3% (n = 6). Synthetic sea water and sea water reference material CRM-SW were used for validation measurements. Aluminium in urine samples of a volunteer who ingested 800 mg of Al(OH)₃ was analyzed.     

Synthesis and characterization of silica-silver core-shell composite particles with uniform thin silver layers

Silica-silver core-shell composite particles with uniform thin silver layers were successfully synthesized by a facile and one-step ultrasonic electrodeposition method. By electrolysis of the slurry consisting of preformed silica spheres and silver perchlorate without any additives, the homogenous composite particles can be prepared. The average size of single silver crystals in the composite is about 12 nm and the thickness of silver layer is 14±2 nm. Moreover, the continuity of Ag distribution, the surface roughness and the thickness of silver layer are controllable by adjusting the current density (I), the concentration of electrolyte (C) and the reaction time (t). Optical properties of the composite particles with different silver content were also investigated.     

Fluorimetric determination of phytic acid in urine based on replacement reaction

A sensitive fluorimetric method for determination of phytic acid in human urine samples was described. The method was based on a fluorimetric replacement reaction, in which the added phytic acid replaced the Cu²⁺ ion from Cu²⁺-gelatin complex, liberating the fluorescent gelatin molecule. The fluorescence of the solution was accordingly recovered proportionally to the amount of the foreign phytic acid. The excitation wavelength was 273.5 nm and the characteristic emission wavelength was 305.0 nm, respectively. The calibration graph was obtained by plotting the recovered fluorescent intensity at maximum 305.0 nm against the added standard phytic acid, and was divided into two sections. One section was linear over the range of 0.40-2.40 mg L⁻¹ with a linear regression equation of I_f = −0.895 + 15.146c (R² > 0.9993), and the other over the range of 2.40-9.20 mg L⁻¹ with a linear regression equation of I_f = −29.526 + 26.113c (R² > 0.9996), respectively. The relative standard deviation (R.S.D.) at 95% confidence degree for a 2.0 mg L⁻¹ of standard phytic acid within 1 month was less than 1.26% (n = 5), indicating the procedure is reproducible. The detection and the quantification limits of phytic acid were estimated to be 0.23 and 0.40 mg L⁻¹, respectively. The proposed method was applied to the determination of phytic acid in urine samples and the found concentrations of phytic acid in urine were in the range of 0.49-0.75 mg L⁻¹ with recoveries of 96.2-108.8%. Comparison of the obtained results with the reported HPLC was performed, indicating the proposed method was reliable.     

Synthesis and applications of surface-grafted Th(IV)-imprinted polymers for selective solid-phase extraction of thorium(IV)

A new functional monomer N-(o-carboxyphenyl)maleamic acid (CPMA) was synthesized and chosen for the preparation of surface-grafted ion-imprinted polymers (IIPs) specific for thorium(IV). Polymerizable double bond was introduced to silica gel surface by amidation reaction between -NH₂ and maleic anhydride. In the ion-imprinting process, thorium(IV) was complexed with the carboxyl groups, then was imprinted in the polymers grafted to the silica gel surface. The imprinted Th(IV) was removed with 3 mol L⁻¹ HCl. The obtained imprinted particles exhibited excellent selectivity and rapid kinetics process for Th(IV). The relatively selective factor (α_r) values of Th(IV)/La(III), Th(IV)/Ce(III), Th(IV)/Nd(III), Th(IV)/U(VI), and Th(IV)/Zr(IV) were 85.7, 88.9, 26.6, 64.4, and 433.8, respectively, which were greater than 1. The precision (R.S.D.), the detection limit (3σ), and the quantification limit (10σ) of the method were 1.9%, 0.51 ng mL⁻¹ and 1.19 ng mL⁻¹, respectively. The prepared IIPs as solid-phase extractants were successfully applied for the preconcentration of trace thorium in natural and certified samples prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES) with satisfactory results.     

A sensitive post-column photochemical derivatization/fluorimetric detection system for HPLC determination of bisphosphonates

A new reversed-phase ion-pair high-performance liquid chromatographic (HPLC) method has been developed for the determination of the following bisphosphonic acids: alendronic acid (ALEN), etidronic acid (ETID), ibandronic acid (IBAN) and risedronic acid (RISE). Separation was achieved on a C₁₈ column using a mixture of 50 mmol L⁻¹ borate buffer pH 9.0 containing 0.25 mmol L⁻¹ tetrabutylammonium chloride and 0.5 mmol L⁻¹ EDTA and acetonitrile (97:3) as the mobile phase. The sensitive detection of the above bisphosphonic acids was based on their oxidation to orthophosphate by the on-line peroxydisulfate-assisted photolysis followed by post-column reaction with molybdate to yield phosphomolybdate. This subsequently reacted with thiamine to generate thiochrome and, finally, the fluorescence of thiochrome was measured at 440 nm with excitation at 375 nm. The developed method is precise with a mean relative standard deviation of 1.3%, sensitive (with a detection limit at the nmol L⁻¹ level), accurate, specific, rapid (analysis time approximately 13 min) and inexpensive because to the low cost of the reagents. The assay was applied to the analysis of the four bisphosphonic acids in commercial dosage formulations, in which the excipients did not interfere with the determination. The method was also applied to the determination of etidronate, risedronate and ibandronate in human urine. Sample preparation involves precipitation of the analytes from urine along with endogenous phosphates such as calcium salts by addition of calcium chloride at alkaline pH and dissolution of the precipitate in 0.05 mol L⁻¹ ethylene glycol-bis(β-aminoethyl ether)-N,N,N′,N′-tetraacetic acid.     

Flow injection analysis of ethyl xanthate by gas diffusion and UV detection as CS2 for process monitoring of sulfide ore flotation

A sensitive and robust analytical method for spectrophotometric determination of ethyl xanthate, CH₃CH₂OCS₂⁻ at trace concentrations in pulp solutions from froth flotation process is proposed. The analytical method is based on the decomposition of ethyl xanthate, EtX⁻, with 2.0 mol L⁻¹ HCl generating ethanol and carbon disulfide, CS₂. A gas diffusion cell assures that only the volatile compounds diffuse through a PTFE membrane towards an acceptor stream of deionized water, thus avoiding the interferences of non-volatile compounds and suspended particles. The CS₂ is selectively detected by UV absorbance at 206 nm (? = 65,000 L mol⁻¹ cm⁻¹). The measured absorbance is directly proportional to EtX⁻ concentration present in the sample solutions. The Beer's law is obeyed in a 1 × 10⁻⁶ to 2 × 10⁻⁴ mol L⁻¹ concentration range of ethyl xanthate in the pulp with an excellent correlation coefficient (r = 0.999) and a detection limit of 3.1 × 10⁻⁷ mol L⁻¹, corresponding to 38 μg L⁻¹. At flow rates of 200 μL min⁻¹ of the donor stream and 100 μL min⁻¹ of the acceptor channel a sampling rate of 15 injections per hour could be achieved with RSD < 2.3% (n = 10, 300 μL injections of 1 × 10⁻⁵ mol L⁻¹ EtX⁻). Two practical applications demonstrate the versatility of the FIA method: (i) evaluation the free EtX⁻ concentration during a laboratory study of the EtX⁻ adsorption capacity on pulverized sulfide ore (pyrite) and (ii) monitoring of EtX⁻ at different stages (from starting load to washing effluents) of a flotation pilot plant processing a Cu-Zn sulfide ore.     

Determination of azoxystrobin residues in grapes, musts and wines with a multicommuted flow-through optosensor implemented with photochemically induced fluorescence

In this paper, the conversion of azoxystrobin in a strongly fluorescent degradation product by UV irradiation with quantitative purposes and its fluorimetric determination are reported for the first time. A multicommuted flow injection-solid phase spectroscopy (FI-SPS) system combined with photochemically-induced fluorescence (PIF) is developed for the determination of azoxystrobin in grapes, must and wine. Grape samples were homogenized and extracted with methanol and further cleaned-up by solid-phase extraction on C₁₈ silica gel. Wine samples were solid-phase extracted on C₁₈ sorbent using dichloromethane as eluent. Recoveries of azoxystrobin from spiked grapes (0.5-2.0 mg Kg⁻¹), must (0.5-2.0 μg mL⁻¹) and wine (0.5-2.0 μg mL⁻¹) were 84.0-87.6%, 95.5-105.9% and 88.5-111.2%, respectively. The quantification limit for grapes was 0.021 mg Kg⁻¹, being within European Union regulations, and 18 μg L⁻¹ and 8 μg L⁻¹ for must and wine, respectively.