New potential humic acid stationary phase toward drug components: Development of a chemometric‐assisted RP‐HPLC method for the determination of paracetamol and caffeine in tablet formulations

A new humic acid based stationary phase has been used, for the first time, to achieve the separation and quantification of paracetamol and caffeine in pharmaceutical preparations under reversed‐phase high‐performance liquid chromatography conditions. Central composite design was applied as a powerful tool to optimize the most dominant parameters that influence the resolution of reversed‐phase high‐performance liquid chromatography, that is, mobile phase composition (acetonitrile percentage in water), flow rate, and column temperature. The optimum conditions were obtained as 21.69%, 1.5 mL/min, and 15°C, respectively, with the aid of a second‐order quadratic model and desirability function. Under the optimum conditions, the peaks could be baseline separated within 10 min. For the developed reversed‐phase high‐performance liquid chromatography method, the linearity was investigated in the concentration ranges of 2–160 mg/mL (R² = 0.999) for paracetamol and 2–9.9 mg/mL (R² = 0.991) for caffeine. Mean recoveries for paracetamol and caffeine were 95.90 and 95.68%, respectively. The limits of detection and quantification were 4.1 × 10^‐4 and 1.3 × 10^‐3 mg/mL for paracetamol and 1.6 × 10^‐4 and 5.0 × 10^‐4 mg/mL for caffeine. The results showed that the new humic acid based stationary phase is very suitable for the separation of paracetamol and caffeine in pharmaceutical preparations and, thus it can be used effectively in the pharmaceutical industry.     

Free radical polymerization of caffeine‐containing methacrylate monomers

The incorporation of acrylic functionality into caffeine enables the preparation of a vast array of novel thermoplastics and thermosets. A two‐step derivatization provided a novel caffeine‐containing methacrylate monomer capable of free radical polymerization. Copolymers of 2‐ethylhexyl methacrylate and caffeine methacrylate (CMA) allowed for a systematic study of the effect of covalently bound caffeine on polymer properties. ¹H NMR and UV‐vis spectroscopy confirmed caffeine incorporation at 5 and 13 mol %, and SEC revealed the formation of high molecular weight (co)polymers (>40,000 g/mol). CMA incorporation resulted in a multistep degradation profile with initial mass loss closely correlating to caffeine content. Differential scanning calorimetry, rheological, and thermomechanical analysis demonstrated that relatively low levels of CMA increased the glass transition temperature, resulting in higher moduli and elucidating the benefits of incorporating caffeine into polymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2829–2837     

Measurement of caffeine and its three primary metabolites in human plasma by HPLC‐ESI‐MS/MS and clinical application

Caffeine is a mild stimulant with significant potential for abuse, being consumed in larger doses with the widespread availability of energy drinks and by novel routes of administration such as inspired powder, oral sprays and electronic cigarettes. How these recent changes in caffeine consumption affecting caffeine disposition and abuse potential is of growing concern. In the study of caffeine disposition in humans, it is common to only measure the caffeine concentration; however, caffeine's three major metabolites (paraxanthine, theobromine and theophylline) retain central nervous system stimulant activity that may contribute to the overall pharmacological activity and toxicity. Therefore, it would be scientifically more rigorous to measure caffeine and its major metabolites in the evaluation of caffeine disposition in human subjects. Herein, we report a method for the simultaneous quantification of caffeine and its three major metabolites in human plasma by high‐performance liquid chromatography coupled to electrospray tandem mass spectrometry (HPLC‐ESI‐MS/MS). Human plasma samples were treated by simple protein precipitation and the analytes were separated using a 6 min gradient program. Precision and accuracy were well within in the 15% acceptance range. The simple sample preparation, short runtime, sensitivity and the inclusion of caffeine's major metabolites make this assay methodology optimal for the study of caffeine's pharmacokinetics and pharmacodynamics in human subjects.     

HgCl2(Caf): Co‐crystallization of Mercuric Chloride and Caffeine

Colourless single crystals of the co‐crystallizate of mercuric chloride and caffeine, HgCl₂(Caf), were obtained from an ethanolic solution of mercuric chloride, HgCl₂, and caffeine (Caf) and recrystallized from hot water. The crystal structure (monoclinic, P2₁, Z = 2, a = 398.36(8), b = 1964.5(4), c = 809.6(2) pm, β = 99.24(3)°, Z = 2, R₁ = 0.0584 for 1430 F_o > 4σ(F_o)) contains helical chains (parallel to the 2₁ screw axis) of almost unaffected HgCl₂ molecules and caffeine molecules which are very weakly bound to one keto‐oxygen atom (O4) of one and N9 of a second caffeine molecule at distances of 282 and 281 pm, respectively. To the contrary, theoretical calculations show that the molecule HgCl₂(Caf)₂ is stable (in the gas phase at T = 0 K) with surprisingly strong bonding as indicated by the “tetrahedrization” of the molecule.     

An efficient and simultaneous analysis of caffeine and paracetamol in pharmaceutical formulations using TLC with a fluorescence plate reader

A simple, rapid, and efficient method using TLC with a fluorescence plate reader has been described for simultaneous determination of caffeine and paracetamol. Determination was carried out using the fluorescence-quenching action of caffeine and paracetamol on a TLC plate with a fluorescent indicator at lambda ex = 254 nm in the linear ranges of 0.2-1.9 and 0.03-1.5 microg/L, respectively. Separation of caffeine and paracetamol were performed on the TLC plate, and the best results were obtained using the optimized mobile phase n-hexane-ethyl acetate-ethanol (2.5 + 1.5 + 0.4, v/v). Some important parameters, such as solvent type and ratio of the mobile phase, the presence of other components, and instrumental parameters, were studied. Caffeine and paracetamol detection limits were 0.025 and 0.032 microg/L, and RSD values for 0.6 microg/L caffeine and 0.06 microg/L paracetamol (n = 5) were 1.93 and 2.06%, respectively. Using this technique, some pharmaceuticals containing caffeine and paracetamol were analyzed with satisfactory results.     

三重-比导数分光光度法同时测定氨基比林、非那西丁和咖啡因含量的研究

阐述了三重-比导数分光光度法同时测定氨基比林、非那西丁和咖啡因的基本原理,并研究了实验条件。试验结果表明,氨基比林的平均回收率为103.3%,相对标准偏差(RSD)为2.3%(n=13);非那西丁的平均回收率为99.44%,RSD为1.2%(n=13);咖啡因的平均回收率为98.41%,RSD为1.1%(n=13)。     

A graphene-based electrochemical sensor for sensitive determination of caffeine

An electrochemical sensor based on the electrocatalytic activity of graphene (Gr) for sensitive detection of caffeine is presented. The electrochemical behaviors of caffeine on Nafion-Gr modified glassy carbon electrode (Nafion-Gr/GCE) were investigated by cyclic voltammetry and differential pulse voltammetry. The results showed that the Nafion-Gr/GCE exhibited excellent electrocatalytic activity to caffeine. Caffeine can be effectively accumulated at Nafion-Gr/GCE and produce a sensitive anodic peak. Such electrocatalytic behavior of Gr is attributed to its unique physical and chemical properties, e.g., subtle electronic characteristics and strong adsorptive capability. This electrochemical sensor shows an excellent performance for detecting caffeine with a detection limit of 1.2×10(-7) M (S/N=3), a reproducibility of 5.2% relative standard deviation, and a satisfied recovery from 98.6% to 102.0%. The sensor shows great promise for simple and sensitive determination of caffeine.     

Determination of caffeine and its metabolites in urine by capillary electrophoresis-mass spectrometry

The caffeine content of foods and beverages varies considerably, interfering with our ability to obtain valid interpretations in many human studies with regard to the mechanism of action(s) of caffeine and/or its metabolites. The rate of metabolism of caffeine and other xanthine drugs also varies greatly from one individual to another. Therefore, it is extremely important to develop accurate, reliable analytical methods to quantify caffeine and its metabolites in simple and complex matrixes. A simple method is described for the separation and characterization of caffeine and its major metabolites employing capillary electrophoresis (CE) coupled to ultraviolet-absorption and mass spectrometry (MS) detection. After optimization of the electrophoresis separation conditions, a reliable separation of caffeine and 11 of its major metabolites was achieved in 50 mM ammonium carbonate buffer, pH 11.0. The volatile aqueous electrolyte system used with a normal electroosmotic flow polarity also provided an optimal separation condition for the characterization of the analytes by MS. The CE method achieved baseline resolution for all 12 compounds in less than 30 min. The CE-MS method is suitable for use as a routine procedure for the rapid separation and characterization of caffeine and its metabolites. The usefulness of this method was demonstrated by the extraction, separation, and identification of caffeine and its 11 metabolites from normal urine samples. The urine specimens were first acidified to obtain optimum binding efficiency to the sorbents of the off-line, solid-phase extraction procedure employed here, and an acidified eluent solvent was employed for the desorption step to maximize the recovery of the bound analytes.     

Synthesis,characterization, and drug release behaviors of a novel thermo‐sensitive poly(N‐acryloylglycinates)

In this study, a novel thermo‐sensitive poly(N‐acryloylglycinates) was prepared in order to get a potential drug release carrier. The corresponding monomers and the polymers were characterized with Fourier‐transform infrared (FTIR) and ¹H NMR. The thermo‐sensitivity of the poly(N‐acryloylglycinates) was evaluated by measuring their lower critical solution temperatures (LCST) in water, inorganic salt solution, and different pH solutions. The results indicated that poly(N‐acryloylglycine methyl ester) (NAGME) and poly(N‐acryloylglycine ethyl ester) (NAGEE) exhibit a reversible thermo‐sensibility in their aqueous solutions at 61.5 and 12.5°C, respectively. However, no thermo‐sensitive behavior of poly(N‐acryloylglycine propyl ester) (NAGPE) was found due to its over hydrophobicity. The swelling studies on hydrogels were carried out at different temperatures, in different pH, and inorganic salt solutions. The hydrogels showed a remarkable phase transition at about 35°C with changing temperature. The release rate of caffeine from the thermo‐sensitive hydrogel was apparently decreased as the crosslinker content increased and temperature decreased. Seventy five percent caffeine from the polymeric hydrogel with 5% NMBA (N, N‐methylenebis(acrylamide)) was released at room temperature within 240 min, whereas 95.4% caffeine diffused into the medium at 37°C. Copyright © 2009 John Wiley & Sons, Ltd.     

Quantitative Auswertung von Dünnschicht-Chromatogrammen: On line-Kopplung mit programmierbaren elektronischen Tischrechnern

A TLC method for the determination of phenacetin and caffeine in pharmaceutical preparations using a densitometer in line with an integrator and electronic desk calculator is described. The calibration curves of each compound were prepared where the higher and lower tolerance concentration levels were defined. The accuracy of the method is 1.51% (phenacetin) and 2.56% (caffeine) for two experiments carried out on each plate; 1.50% (phenacetin) and 2.64% (caffeine) for four experiments for each plate (relative standard deviation, n=18 and n=36, respectively).     

Physical origin of peak tailing on C18-bonded silica in reversed-phase liquid chromatography

Single component isotherm data of caffeine and phenol were acquired on two different stationary phases for RPLC, using a methanol/water solution (25%, v/v, methanol) as the mobile phase. The columns were the non-endcapped Waters Resolve-C18, and the Waters XTerra MS C18. Both columns exhibit similar C18 -chain densities (2.45 and 2.50 micromol/m2) and differ essentially by the nature of the underivatized solid support (a conventional, highly polar silica made from water glass, hence containing metal impurities, versus a silica-methylsilane hybrid surface with a lower density of less acidic free silanols). Thirty-two adsorption data points were acquired by FA, for caffeine, between 10(-3) and 24 g/l, a dynamic range of 24,000. Twenty-eigth adsorption data points were acquired for phenol, from 0.025 to 75 g/l, a dynamic range of 3000. The expectation-maximization procedure was used to derive the affinity energy distribution (AED) from the raw FA data points, assuming a local Langmuir isotherm. For caffeine, the AEDs converge to a bimodal and a quadrimodal distribution on XTerra MS-C18 and Resolve-C18, respectively. The values of the saturation capacity (q(s,1) approximately equal to 0.80 mol/l and q(s,2) approximately equal to 0.10 mol/l) and the adsorption constant (b1 approximately equal to 3.11/mol and b2 approximately equal to 29.1 l/mol) measured on the two columns for the lowest two energy modes 1 and 2, are comparable. These data are consistent with those previously measured on an endcapped Kromasil-C18 in a 30/70 (v/v), methanol/water solution (q(s,1) = 0.9 mol/l and q(s,2) = 0.10 mol/l, b1 = 2.4 l/mol and b2 = 16.1 l/mol). The presence of two higher energy modes on the Waters Resolve-C18 column (q(s,3) approximately equal to 0.013 mol/l and q(s,4) approximately equal to 2.6 10(-4) mol/l, b3 approximately equal to 252 l/mol and b4 = 13,200 l/mol) and the strong peak tailing of caffeine are explained by the existence of adsorption sites buried inside the C18-bonded layer. It is demonstrated that strong interactions between caffeine and the water protected bare silica surface cannot explain these high-energy sites because the retention of caffeine on an underivatized Resolve silica column is almost zero. Possible hydrogen-bond interactions between caffeine and the non-protected isolated silanol groups remaining after synthesis amidst the C18-chain network cannot explain these high energy interactions because, then, the smaller phenol molecule should exhibit similarly strong interactions with these isolated silanols on the same Resolve-C18 column and, yet, the consequences of such interactions are not observed. These sites are more consistent with the heterogeneity of the local structure of the C18-bonded layer. Regarding the adsorption of phenol, no matter whether the column is endcapped or not, its molecular interactions with the bare silica were negligible. For both columns, the best adsorption isotherm was the Bilangmuir model (with q(s,1) approximately equal to 2 and q(s,2) approximately equal to 0.67 mol/l, b1 0.61 and b2 approximately equal to 10.3 l/mol). These parameters are consistent with those measured previously on an endcapped Kromasil-C18 column under the same conditions (q(s,1) = 1.5 and q(s,2) = 0.71 mol/l, b1 = 1.4 l/mol and b2 = 11.3 l/mol). As for caffeine, the high-energy sites are definitely located within the C18-bonded layer, not on the bare surface of the adsorbent.     

Monitoring bronchodilators with direct injection

A procedure was developed for the determination of caffeine and theophylline using a C18 column (5 microm, 250 mm x 4.6 mm) and micellar liquid chromatography using hybrid mobile phases containing sodium dodecyl sulfate (SDS) and propanol, butanol or pentanol as modifiers. Detection was performed with a variable wavelength UV-vis detector at 272 nm. After the application of an interpretative strategy for the selection of the optimimum mobile phase, caffeine and theophylline can be resolved and determined in serum samples by direct injection, using a mobile phase made up of 50 mM SDS-2.5% (v/v) propanol-10 mM KH2PO4, pH 7, with an analysis time below 5 min. Calibration was linear in the range 0.05 to 50 microg mL(-1) with r > 0.999. The statistical evaluation of the method was examined by performing intra-day (n = 6) and inter-day calibration (n = 7) and was found to be satisfactory, with highly accurate and precise results. The proposed method was suitably validated and applied to the determination of caffeine and theophylline in serum samples of patients treated with bronchodilators.     

In vivo evaluation of CYP1A2, CYP2A6, NAT-2 and xanthine oxidase activities in a Greek population sample by the RP-HPLC monitoring of caffeine metabolic ratios

A RP-HPLC method was developed for the assessment of caffeine and its metabolites in urine and was used for the evaluation of the CYP1A2, CYP2A6, xanthine oxidase (XO) and N-acetyl-transferase-2 (NAT-2) in vivo activities in 44 Greek volunteers (21 men, 23 women). Spot urine samples were analyzed 6 h after 200 mg caffeine consumption, following a 30 h methylxantine-free diet. The major urinary caffeine metabolites are 1-methyluric acid (1U), 5-acetylamino-6-formylamino-3-methyluracil (AFMU), 1-methylxanthine (1X), 1,7-dimethyluric acid (17U) and 1,7-dimethylxanthine (17X). CYP1A2, CYP2A6, XO and NAT-2 activities were estimated from the metabolic ratios (AFMU + 1U + 1X)/17U, 17U/17X, 1U/(1X + 1U) and AFMU/(AFMU + 1U + 1X), respectively. Metabolites and internal standard were extracted with chloroform/isopropanol (85:15, v/v) and separated on a C18 column by an isocratic HPLC system using a two-step elution with manual switch from solvent A (0.1% acetic acid-methanol-acetonitrile, 92:4:5 v/v) to solvent B (0.1% acetic acid-methanol, 60:40, v/v), and detected at 280 nm. The method exhibited adequate metabolite separation (resolution factors >1.48), accuracy (94.1-106.3%) and intraday and interday precision <8.02 and <8.78%, respectively (n = 6). Smoking affected only CYP1A2, whereas gender had no effect in any enzyme activity. NAT-2 exhibited bimodal distribution, 63.6% of volunteers being slow acetylators. The developed RP-HPLC method was fully validated and successfully applied for the evaluation of CYP1A2, CYP2A6, XO and NAT-2 activities.     

Automated interface for hyphenation of planar chromatography with mass spectrometry

A fully automated interface to couple high-performance thin-layer chromatography (HPTLC) with mass spectrometry (MS) is described. This universal hands-free interface connects intact normal-phase plates to any liquid chromatography/mass spectrometry (LC/MS) system without any adjustments or modifications to the mass spectrometer. The interface extracts the complete substance band with its depth profile and thus allows detections in the pg/band range. The high performance of the automated interface was evaluated through caffeine quantification in real samples, viz., energy drinks and pharmaceutical tablets, without internal standard. Following chromatographic separation on silica gel 60 F(254) HPTLC plates, caffeine bands were eluted from the plate by means of the automated interface to the electrospray ionization (ESI) source of a triple-quadrupole mass spectrometer. Since in full scan mode only the protonated molecule [M+H](+) was observed, caffeine quantification was performed using the selected-ion monitoring (SIM) mode at m/z 195. The validation showed highly reliable results for the linear range (R(2) = 0.9973), repeatability (RSD = 5.6%, n = 6) and intermediate precision (RSD = 1.5%, n = 3). Regarding accuracy the results obtained by HPTLC/MS were not statistically different (F-test, t-test) from those obtained by validated HPTLC/UV methods. Hence, this interface proved to be one of the most reliable and universal interfaces for HPTLC/MS.     

Sensitive determination of MDMA and its metabolite MDA in rat blood and brain microdialysates by HPLC with fluorescence detection

Simultaneous determination of 3,4-methylenedioxymethamphetamine (MDMA) and 3,4-methylenedioxyamphetamine (MDA) in rat blood and brain microdialysates by high-performance liquid chromatography with fluorescence detection (HPLC-FL) was developed. Microdialysates were directly subjected to derivatization with 4-(4,5-diphenyl-1H-imidazol-2-yl)benzoyl chloride (DIB-Cl). The DIB-derivatives of MDMA, MDA and the internal standard, 1-methyl-3-phenylpropylamine (MPPA), were isocratically separated on an ODS column using a mixture of 50 mm phosphate buffer (pH 7.0)-acetonitrile-methanol-2-propanol (50:45:5:2, v/v/v/v %) as an eluent at a flow rate of 1.5 mL/min. The calibration curves of MDA and MDMA spiked to blood and brain microdialysates were linear over the ranges 2.5-500 and 5.0-1000 ng/mL, respectively. The detection limits of MDA and MDMA were 1.2 and 4.2 for blood and 1.3 and 4.8 ng/mL for brain, respectively. Additionally, the intra- and the inter-assay precisions were lower than 5.6% for the blood and brain microdialysates (n = 4). The proposed method was successfully applied for the monitoring of MDMA and its metabolite MDA in rat blood and brain microdialysates, and the pharmacokinetic parameters of MDMA and MDA in the microdialysates after administration of MDMA (5 mg/kg, i.p.) with or without caffeine (20 mg/kg, i.p.) were evaluated.     

Simultaneous Determination of Caffeine and Acetylsalicylic Acid in Pharmaceutical Formulations Using a Boron‐Doped Diamond Film Electrode by Differential Pulse Voltammetry

This work presents a simple, fast and low‐cost method for simultaneous determination of acetylsalicylic acid (ASA), without alkaline hydrolysis and caffeine (CF) in pharmaceutical formulations using a boron‐doped diamond as the working electrode through differential pulse voltammetry. A good repeatability was reached for 20 measurements, with a low relative standard deviation of less than 1.0 %. The calibration curves presented a great linear correlation coefficient for both drugs (R=0.999) with a limit of detection of 1.6×10^?7 mol L^?1 for CF and 2.3×10^?7 mol L^?1 for ASA. The system was validated in comparison with the official method.     

Development and validation of a method for determination of caffeine in diuretic tablets and capsules by high-performance thin-layer chromatography on silica gel plates with a concentration zone using manual spotting and ultraviolet absorption densitometry

A new quantitative method using silica gel high-performance thin-layer chromatography plates with channels and a concentration zone, manual application of standards and samples, development with methanol-ethyl acetate (15 + 85) mobile phase, and ultraviolet absorption densitometry is reported for the determination of caffeine in diuretic pharmaceutical preparations. Tablet and capsule products containing potassium salicylate, acetaminophen, and salicylamide as active ingredients were analyzed to test the applicability of the new method, and precision, accuracy, linearity, limits of detection and quantitation, and selectivity were validated. The milligrams of caffeine in each tablet ranged from 48.0 to 51.0, and the milligrams in each capsule from 37.9 to 40.3. Within-day precision was 1.48 and 1.78% (n=6), and interday precision 0.723 and 1.26% (n=5) for analysis of 2 tablets and 2 capsules, respectively. Accuracy validation of the tablet and capsule results produced errors of 1.0 and 1.9% for spiked blank analyses and 2.6 and 3.5% for standard addition analyses, respectively. A comparative study using a caffeine standard solution and a multicomponent analgesic tablet solution containing caffeine, acetaminophen, and acetylsalicylic acid showed that manual application on the concentration zone, instrumental application on the concentration zone, and instrumental application on the silica gel gave quite similar results in terms of number of theoretical plates, resolution, limit of detection, and linearity.     

Electrochemical Sensor for Caffeine Based on a Glassy Carbon Electrode Modified with an Attapulgite/Nafion Film

In the present work, a simple and economic analytical method based on attapulgite/nafion coated glassy carbon electrode (AT/Naf/GCE) has been developped for the electrochemical determination of caffeine. Prior to its use, the ionic exchange properties and conductivity of AT/Naf/GCE were studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Caffeine gave an irreversible oxidation peak around +1.41 V (vs Ag/AgCl reference electrode) in 0.1 M H₂SO₄ at pH 1.5. The peak current varied linearly with the square root of the scan rate, showing that the transfer process is controlled by diffusion. The heterogeneous rate constant, the transfer coefficient and the number of electrons involved were calculated. Upon optimization of key analytical parameters involved in the electroanalysis of caffeine by DPV, the recorded oxidation peak current varied linearly with caffeine concentration in the range from 0.1 to 4 μm, leading to a detection limit of 4.57×10^?8 M (S/N=3). The developed electrode exhibited good stability and was easily regenerated. The effect of some important potential interfering compounds (ascorbic acid, dopamine, uric acid, sulphite ions and glucose) on the signal of caffeine was also examined. The obtained electrode was successfully employed in the determination of caffeine content in a commercial drug.     

Fiber‐in‐tube solid‐phase microextraction of caffeine as a molecular tracer in wastewater by electrochemically deposited layered double hydroxide

Modified stainless‐steel wires with a layer of polyaniline conductive polymer were coated by electrochemical deposition with Zn/Al layered double hydroxide to make solid‐phase microextraction fibers. The coating layer was also electrochemically deposited on the inner surface of a stainless‐steel tube. Then, ten prepared fibers were put inside the inner coated tube to make a fiber‐in‐tube solid phase microextraction device. The device was applied for the extraction of caffeine (1,3,7‐trimethylxanthine) from domestic wastewater samples. Extraction conditions including extraction and desorption times, pH and ionic strength of the sample solution, and content of the organic desorption solvent were investigated and optimized. Under the optimized conditions, the fiber‐in‐tube solid phase microextraction exhibited excellent extraction efficiency toward caffeine. The precision of the method was evaluated. Average relative standard deviation of 5.7% (n = 6) for intraday analysis and 8.3% (n = 5) for interday analysis was obtained. The limits of detection and limits of quantification of the method (at signal to noise ratio of 3 and 10) were obtained as 0.14 and 0.37 ng/mL, respectively. The current study can provide new prospective applications of layered double hydroxide conductive polymer fiber coatings.     

以马来松香丙烯酸乙二醇酯为交联剂的咖啡因分子印迹电化学传感器

以咖啡因为模板分子, 含菲环骨架的马来松香丙烯酸乙二醇酯为交联剂, 甲基丙烯酸为功能单体, 在玻碳电极表面以自由基热聚合的方式制备分子印迹聚合物敏感膜, 构建了测定咖啡因的新型分子印迹膜电化学传感器. 通过循环伏安法、 差分脉冲伏安法及电化学交流阻抗法研究了传感器对咖啡因的响应特性. 结果表明, 在最佳的实验条件下, 传感器的峰电流与咖啡因浓度在3.00×10^-3~2.73 mmol/L范围内呈现良好的线性关系, 检出限(S/N=3)为1.12×10^-4 mmol/L. 传感器具有良好的选择性和重现性. 将该传感器用于可口可乐饮料中咖啡因含量的测定, 平均回收率为98.7%.