Thermoluminescence and optically stimulated luminescence characteristics of Al2O3 doped with Tb

In the present work policrystals of α − Al₂O₃ doped with terbium were synthesized using the solvent evaporation method. The samples were prepared using Al(NO₃)₃·9H₂O and Tb(NO₃)₃·5H₂O reagents, with Tb concentrations between 1 and 5 mol% and thermally treated at high temperature above ∼1400 °C. X-ray diffraction measurements showed the α-phase formation of samples. TL glow curve presented an intense peak at ∼190 °C and two other with low intensity at 290 and 350 °C after gamma irradiation. The best doping concentration which presented high luminescence was the sample doped with 3 mol% of Tb. TL spectra and fluorescence measurements showed similar luminescence spectra with lines attribute to Tb³⁺ ions. A linear behavior to gamma dose between 1 and 20 Gy was observed in TL, using 190 °C peak as well as in OSL signal, this last carried out using 532 nm wavelength stimulation.     

Enhanced luminescence and degradation of SiO2:Ce,Tb powder phosphors prepared by a sol-gel process

Enhanced green photoluminescence and cathodoluminescence (CL) from Tb³⁺ ions due to co-doping with Ce³⁺ ions were observed from SiO₂:Ce,Tb powder phosphors prepared by a sol-gel technique. Blue emission from the Ce³⁺ ions was completely suppressed by Tb co-doping, presumably due to energy transfer from Ce³⁺ to Tb³⁺. In addition, the green CL intensity from SiO₂:Ce,Tb degraded by ∼50% when the powders were irradiated for 10 h with a 2 keV, 54 mA/cm² beam of electrons in an ultra-high vacuum chamber containing either 1×10⁻⁸ or 1×10⁻⁷ Torr O₂. Desorption of oxygen from the surface was observed during the decrease of CL intensity. The mechanisms for energy transfer from Ce³⁺ ions to Tb³⁺ ions to enhance the green luminescence, and mechanisms for desorption of oxygen from the phosphor surface that would result in decreased CL intensity are discussed.     

Dosimeter properties of Ce and Eu doped LiCaAlF6

Optical, scintillation properties, optical stimulated luminescence, and thermally stimulated luminescence of Ce 1, 3, and 5% doped and Eu 1, 1.5, and 2% doped LiCaAlF₆ crystals fabricated by Tokuyama Corp. were investigated. In transmittance, absorption was proportional to dopant concentrations and typical optical quantum yield of Ce and Eu-doped LiCaAlF₆ were 40 and 100%, respectively. Scintillation wavelength and decay time profiles were investigated under X-ray irradiation. Ce³⁺ and Eu²⁺ 5d-4f luminescence appeared around 300 nm and 370 nm with typical decay time of 40 ns and 1.5 μs, respectively. Optically stimulated luminescence of Ce-doped ones appeared under 405 nm stimulation with detectable intensity while those of Eu doped ones were quite weak. Thermally stimulated luminescence of Ce- and Eu-doped LiCaAlF₆ were enough strong and they exhibited good response function from 1 to 1000 mGy exposure.     

Scintillation and optical stimulated luminescence of Ce-doped CaF2

Scintillation and optical stimulated luminescence of Ce 0.1–20% doped CaF₂ crystals prepared by Tokuyama Corp. were investigated. In X-ray induced scintillation spectra, luminescence due to Ce³⁺ 5d–4f transition appeared around 320 nm with typically 40 ns decay time. By ²⁴¹Am 5.5 MeV α-ray irradiation, 0.1% doped one showed the highest scintillation light yield and the light yield monotonically decreased with Ce concentrations. Optically stimulated luminescence after X-ray irradiation was observed around 320 nm under 550 or 830 nm stimulation in all samples. As a result, intensities of optically stimulated luminescence were proportional to Ce concentrations. Consequently, scintillation and optically stimulated luminescence resulted to have a complementary relation in Ce-doped CaF₂ system.     

Investigation of the photoluminescence properties of composite optical resins containing high lanthanide content

Novel composite optical resins with high lanthanide content have been synthesized through a free radical copolymerization of methacrylic acid (MA), styrene (St) and Eu(DBM)₃·H₂O nanocrystals. We characterized the structure, the thermal properties, dimensions and photoluminescence properties of Eu(DBM)₃·H₂O nanocrystals. Our results indicated that the diameters of the Eu(DBM)₃·H₂O nanocrystals were within the range of 30 to 300 nm. These materials exhibited characteristic europium ion luminescence. The europium-bearing nanocrystals and were then incorporated into the copolymer systems of MA/St and luminescence functional optical resins with high lanthanide content (50 wt%) were obtained. The combination of these particles and optical resins is facile because the diameter of Eu(DBM)₃·H₂O is decreased. These copolymer-based optical resins not only possess good transparency and mechanical performance, but also exhibit an intense narrow band emission of lanthanide complexes and longer fluorescence lifetimes under UV excitation at room temperature.     

Luminescence decay kinetics of Eu<Superscript>3+</Superscript> ions in phosphate glasses of different composition under photo- and electron excitations

The influence of matrix composition, coactivators, and excitation method on the luminescence kinetics of Eu³⁺ ions in lithium–phosphate and lithium–phosphate–borate glasses activated by Eu, Eu/Tb, and Eu/Dy is studied. Luminescence is excited by a high current electron beam and a xenon lamp. It is found that, under photoexcitation, the europium luminescence decays more slowly than under electronic excitation. Depending on the content of cation modifiers ZnO and Li₂O, the decay time decreases with increasing amount of ZnO. The decay time weakly depends on the europium concentration. The decay of the luminescence of europium ions is well described by the Inokuti–Hirayama model.     

Europium(III) Concentration Effect on the Spectroscopic and Photoluminescent Properties of BaMoO4:Eu

BaMoO₄:Eu (BEMO) powders were synthesized by the polymeric precursor method (PPM), heat treated at 800 °C for 2 h in a heating rate of 5 °C/min and characterized by powder X-ray diffraction patterns (XRD), Fourier Transform Infra-Red (FTIR) and Raman spectroscopy, besides room temperature Photoluminescence (PL) measurements. The emission spectra of BEMO samples under excitation of 394 nm present the characteristic Eu³⁺ transitions. The relative intensities of the Eu³⁺ emissions increase as the concentration of this ion increases from 0.01 to 0.075 mol, but the luminescence is drastically quenched for the Ba_0.855Eu_0.145MoO₄ sample. The one exponential decay curves of the Eu^{3+ 5}D₀→⁷F₂ transition, λ _exc = 394 nm and λ _em = 614 nm, provided the decay times of around 0.54 ms for all samples. It was observed a broadening of the Bragg reflections and Raman bands when the Eu⁺³ concentration increases as a consequence of a more disordered material. The presence of MoO₃ and Eu₂Mo₂O₇ as additional phases in the BEMO samples where observed when the Eu³⁺ concentration was 14.5 mol%.     

Synthesis and Fluorescence Properties of Lanthanide (III) Perchlorate Complexes with Naphthyl-Naphthalinesulphonylpropyl Sulfoxide

A ligand with double sulfinyl groups, naphthyl-naphthalinesulphonylpropyl sulfoxide(dinaphthyl disulfoxide, L), was synthesized by a new method and its several lanthanide (III) complexes were synthesized and characterized by element analysis, molar conductivity, coordination titration analysis, IR, TG-DTA, ¹HNMR and UV spectra. The composition of these complexes, were RE₂(ClO₄)₆·(L)₅·nH₂O (RE = La, Nd, Eu, Tb, Yb, n = 2 ∼ 6, L = C₁₀H₇SOC₃H₆SOC₁₀H₇). The fluorescent spectra illustrated that the Eu (III) complex had an excellent luminescence. It was supposed that the ligand was benefited for transferring the energy from ligand to the excitation state energy level (⁵D₀) of Eu (III). The Tb (III) complex displayed weak luminescence, which attributed to low energy transferring efficiency between the average triplet state energy level of ligand and the excited state (⁵D₄) of Tb (III). So the Eu (III) complex displayed a good antenna effect for luminescence. The phosphorescence spectra and the relationship between fluorescence lifetime and fluorescence intensity were also discussed.     

CaS:Ce,Tb中Tb3+到Ce3+的能量传递

本文通过发射光谱、激发光谱和发光的衰减特性,研究了三价稀土离子Ce3+和Tb3+在CaS基质中的相互作用。实验结果表明,在CaS中Tb3+敏化了Ce3+的发光,监测Ce3+的发光(505nm),在激发光谱中出现Tb3+中心特征辐射的激发带。而且在CaS:Ce、Tb中,Ce3+中心的发光衰减变慢,衰减后期的慢成份正是反映了能量施主Tb3+的衰减特性,证明在CaS:Ce、Tb中存在着Tb3+到Ce3+的能量传递。     

Synthesis and Fluorescence Properties of Lanthanide (III) Perchlorate Complexes with Bis(benzoylmethyl) Sulfoxide

A ligand with two carbonyl groups and one sulfinyl group has been synthesized by a new method and its several lanthanide (III) complexes were synthesized and characterized by element analysis, molar conductivity, coordination titration analysis, IR, TG-DSC, ¹H NMR and UV spectra. The results indicated that the composition of these complexes is REL₅(ClO₄)₃·3H₂O (RE = La(III), Pr(III), Eu(III), Tb(III), Yb(III), L = C₆H₅COCH₂SOCH₂COC₆H₅). The fluorescent spectra illustrate that both the Tb (III) and Eu (III) complexes display characteristic metal-centered fluorescence in solid state, indicating the ligand favors energy transfer to the excitation state energy level of them. However, the Tb (III) complex displays more effective luminescence than the Eu (III) complex, which is attributed to especial effectively in transferring energy from the average triplet energy level of the ligands (T) onto the excited state (⁵D₄) of Tb (III) than that (⁵D₀) of Eu (III), showing a good antenna effect for Tb(III) luminescence. The phosphorescence spectra and the relationship between fluorescence lifetimes and fluorescence intensities were also discussed.     

Luminescence and Scintillation Characterization of Cs2NaGdBr6: Ce3+ Single Crystal

Luminescence and scintillation properties of newly discovered bromo-elpasolites Cs₂NaGdBr₆: Ce³⁺ (CNGB: Ce³⁺) are presented. Single crystals of CNGB: Ce³⁺ with dimensions up to Ø7×10 mm³ are successfully grown by the Bridgman technique. X-ray excited luminescence measurements of the grown samples showed a broad emission band in the wavelength range from 365 to 470 nm. It offered an energy resolution of 5.1% (FWHM) at 662 keV for 10% Ce sample. The light output of the investigated samples increases along with cerium concentration. A maximum light yield of ～36,800 ph/MeV is measured for the 10% Ce sample crystal. Under γ-ray excitation, CNGB: Ce³⁺ crystals showed three exponential decay time components. The scintillation mechanism in the sample crystal is presented.     

Effect of excitation level on the photoluminescence of barium thiogallate activated with europium and cerium ions

The photoluminescence of barium thiogallates doped with Eu²⁺, Ce³⁺, and Eu²⁺ + Ce³⁺ ions is studied over a wide range of excitation levels (10^–3–10⁶ W/cm²). Introduction of 3 at.% Eu and 3 at.% Ce instead of 5 at.% Eu into a BaGa₂S₄ matrix doubles the luminescence quantum yield of the phosphor. Doped BaGa₂S₄ exhibits a high linearity in its luminescence intensity as a function of excitation level (a constant efficiency) up to 2·10⁴ W/cm² for excitation pulse durations of 8 ns, which corresponds to cw pumping at a power density of about 5·10² W/cm² in terms of the concentration of excited ions. It is shown that using BaGa₂S₄:Eu,Ce along with the “yellow” phosphor of a Nichia NS6L083 LED may increase its color rendering index from 0.64 to 0.80 with no reduction in its luminous efficiency.     

Luminescence enhancement by the reduction–oxidation synthesis in monoclinic RE2O3 (RE=Eu,Gd) phosphors containing Eu3+ activator

A novel synthesis was developed for enhanced luminescence in sesquioxide phosphors containing Eu³⁺ activator. It consisted of two annealing steps: reduction under vacuum with gaseous H₂ at 10 Torr and 1300 °C and re-oxidation at 300–1500 °C in air. The integrated luminescence intensity of the monoclinic Eu₂O₃ phosphor was enhanced ca. 21 times by this method compared with conventional processing. The photoluminescence (PL) intensity was maximized at re-oxidation temperatures of 500–1100 °C. The PL characteristics of monoclinic Eu₂O₃ and Gd₂O₃:0.06Eu samples were compared with a commercial cubic Y₂O₃:Eu phosphor. The evolution of physical characteristics during the two-step annealing was studied by Raman spectroscopy, XPS, XRD, PL decay analysis, and SEM. PL decay lifetime increased proportionally to the PL intensity over the range 0.5–100 μs. Additional vibrational modes appeared at 490, 497, and 512 cm^?1 after the two-step annealing. The increase in PL intensity was ascribed to the formation of excess oxygen vacancies and their redistribution during annealing. Resonance crossovers between the charge transfer state and the emitting ⁵D_J states are discussed in relation to reported luminescence saturation mechanisms for oxysulfides Ln₂O₂S:Eu³⁺ (Ln=Y, La).     

Na2CaSiO4∶RE3+(RE=Ce3+,Tb3+,Eu3+) 的制备及发光特性

采用高温固相法,合成了三价稀土离子(RE³⁺=Ce³⁺, Tb³⁺, Eu³⁺)掺杂的Na₂CaSiO₄(NCS)系列样品,并研究了其在紫外光激发下的发光特性。研究结果表明,Ce³⁺、Tb³⁺ 和Eu³⁺掺杂的NSC系列样品在紫外光源激发下,均呈现其特征发射,随着掺杂浓度的提高,发射强度逐渐增大。Ce³⁺、Tb³⁺和Eu³⁺的最佳摩尔分数分别为0.13、0.13和0.12,相应的色坐标分别计算为(0.17, 0.17)、(0.34, 0.58)和(0.66, 0.34),分别为很好的蓝光、绿光和红光。继续增加稀土离子的含量,发射强度降低。     

Further performance tests of a picosecond X-ray and laser induced streak camera system with fast scintillation materials

A further performance test of a fluorescence lifetime spectroscopy system with 2D-photon counting based on a streak camera was carried out. This system offers three different excitation light sources. It includes a pulsable X-ray tube with 40 kV and a laser. A pulsed UV-LED has been installed for sample excitation. The table top measurement device has a temporal resolution down to 20 ps after deconvolution and fluorescence/scintillation decay times can be evaluated in a wavelength selectable range between 200 and 850 nm. Cesium fluoride, cesium chloride and cesium bromide as fast core-valence luminescence emitters with a relatively low light yield were used in the presented performance test. The easily manageable system is able to detect low light levels and to determine the decay times in agreement with literature in most instances. Beside mentioned scintillators PbCO₃, SrI₂ and Lu₂SiO₅:Ce as a high light yield material were also measured.     

Thermoluminescent analysis of CaSO4:Tb,Eu crystal powder for dosimetric purposes

The motivation of this work was to produce crystals of CaSO₄ doped with an unusual combination of RE elements such as terbium (Tb) and europium (Eu) in different concentrations, and analyze its thermoluminescent (TL) properties. The crystals were produced by the slow evaporation route using calcium carbonate (CaCO₃) as precursor, and incorporating the dopants (Tb₂O₃ and Eu₂O₃) in a solution of sulfuric acid, that is evaporated and collected again, leaving just CaSO₄:Tb,Eu crystal powder. The terbium and europium ions were incorporated in concentration ratios of 1:1, 2:1 and 5:1 (weight proportions). X-ray diffraction analyses showed that samples of doped CaSO₄ exhibit only a single phase corresponding to the crystal structure of anhydrite. The radioluminescence confirmed the presence of Tb³⁺ and Eu²⁺ in the crystal matrix. The CaSO₄:Tb,Eu crystal powders showed TL emission glow curves with three peaks centered around 170 °C, 270 °C and 340 °C, after irradiation with a ⁹⁰Sr/⁹⁰Y source. Thermoluminescent (TL) characteristics such as linearity, reproducibility and fading were evaluated. Samples produced with concentration ratio of 2:1 of Tb and Eu showed the highest TL intensity. The produced CaSO₄:Tb,Eu samples present TL properties useful for dosimetric purposes.     

Luminescent features of sol–gel derived rare-earth multi-doped oxyfluoride nano-structured phosphors for white LED application

Rare-earth doped oxyfluoride 75SiO₂:25PbF₂ nano-structured phosphors for white-light-emitting diodes were synthesized by thermal treatment of precursor sol–gel derived glasses. Room temperature luminescence features of Eu³⁺, Sm³⁺, Tb³⁺, Eu³⁺/Tb³⁺, and Sm³⁺/Tb³⁺ ions incorporated into low-phonon-energy PbF₂ nanocrystals dispersed in the aluminosilicate glass matrix and excited with UV light emitting diode were investigated. The luminescence spectra exhibited strong emission signals in the red (600, 610, 625, and 646 nm), green (548 and 560 nm), and blue (485 nm) wavelength regions. White-light emission was observed in Sm/Tb and Eu/Tb double-doped activated phosphors employing UV-LED excitation at 395 nm. The dependence of the luminescence emission intensities upon annealing temperature and rare-earth concentration was also examined. The results indicated that there exist optimum annealing temperature and activator ion concentration in order to obtain intense visible emission light with high color rendering index. The study suggests that the nanocomposite phosphor based upon 75SiO₂:25PbF₂ host herein reported is a promising contender for white-light LED applications.     

Peculiarities of luminescent properties of cerium doped YAG transparent nanoceramics

Optical and luminescence properties of transparent nanosized cerium doped Y₃Al₅O₁₂ (YAG:Ce) ceramics have been studied. YAG:Ce nanoceramics were obtained by means of low temperature and high pressure (LTHP) sintering method. Nanoceramic samples were sintered in the 2–8 GPa pressure range, whereas Ce³⁺ concentration was varied in the 0.5–5 at. % range. It is shown that, in contrast to the single crystal, a strong rise of absorption coefficient was detected already at wavelength shorter than 400 nm in all nanoceramic samples studied. Furthermore, in nanoceramic samples unusual UV emission band near 3.1 eV was observed, which is not observed in the YAG:Ce single crystal. High pressure applied during nanoceramics sintering leads to significant changes in their optical and luminescence properties.     

Scintillation timing characteristics of (La,Gd)2Si2O7:Ce and Gd2SiO5:Ce single crystal scintillators: A comparative study

The scintillation timing characteristics of (La,Gd)₂Si₂O₇:Ce (GPSLa23.5%:Ce) single crystal were studied and compared with Gd₂SiO₅:Ce (GSO:Ce) single crystal. The photoelectron yield, scintillation decay times and coincidence time resolution were measured. At 511 keV γ-rays, the photoelectron yield of 10,770 ± 500 phe MeV⁻¹ and energy resolution of 5.4 ± 0.2% obtained for GPSLa23.5%:Ce are much better than those of 3350 ± 160 phe MeV⁻¹ and 7.8 ± 0.3% obtained for GSO:Ce. The scintillation decay time profile was measured by the time-correlated single photon counting technique using a fast-slow coincidence setup. In both materials the comparable rise times of several nanoseconds are present. The fast component decay time of 56 ns with relative intensity of 49% obtained for GPSLa23.5%:Ce is inferior to that of 32 ns(88%) obtained for GSO:Ce. Consequently, the coincidence time resolution of GPSLa23.5%:Ce is slightly worse than that of GSO:Ce. The normalized time resolution was also discussed in terms of a number of photoelectrons and decay time of the scintillation pulse.     

Sensitization of Luminescence of Europium Compounds on Solid Matrices by Terbium (III) Ions

The conditions of sensitization of the luminescence of Eu(III) by Tb(III) ions in complexes with inorganic (Na₂WO₄) and organic (nalidixic acid) ligands in sorbates on solid matrices (zeolite CaX and crystalline zirconium phosphate (ZrP)) and in coprecipitation with CaWO₄ have been investigated. It has been established that the maximum sensitization of the europium luminescence is attained in the case where Eu and Tb are present in a 1:0.5 ratio. In this case, the integral intensity of luminescence of Eu(III) (the band with _max = 612 nm) in the sorbate of its complex with nalidixic acid on ZrP accounts for more than 60% of the luminescence intensity of the industrial photoluminophor Y₂O₃:Eu (FL-612) possessing red luminescence, and the intensity of Tb(III) luminescence (the band with _max = 545 nm) accounts for about 40% of the luminescence intensity of the photoluminophor Gd₂O₂S:Tb possessing green luminescence.